#include <linux/phy.h>
#include <linux/timer.h>
#include <linux/workqueue.h>
+#include <linux/mdio.h>
#include <linux/atomic.h>
#include <asm/io.h>
schedule_delayed_work(&phydev->state_queue, PHY_STATE_TIME * HZ);
}
+
+static inline void mmd_phy_indirect(struct mii_bus *bus, int prtad, int devad,
+ int addr)
+{
+ /* Write the desired MMD Devad */
+ bus->write(bus, addr, MII_MMD_CTRL, devad);
+
+ /* Write the desired MMD register address */
+ bus->write(bus, addr, MII_MMD_DATA, prtad);
+
+ /* Select the Function : DATA with no post increment */
+ bus->write(bus, addr, MII_MMD_CTRL, (devad | MII_MMD_CTRL_NOINCR));
+}
+
+/**
+ * phy_read_mmd_indirect - reads data from the MMD registers
+ * @bus: the target MII bus
+ * @prtad: MMD Address
+ * @devad: MMD DEVAD
+ * @addr: PHY address on the MII bus
+ *
+ * Description: it reads data from the MMD registers (clause 22 to access to
+ * clause 45) of the specified phy address.
+ * To read these register we have:
+ * 1) Write reg 13 // DEVAD
+ * 2) Write reg 14 // MMD Address
+ * 3) Write reg 13 // MMD Data Command for MMD DEVAD
+ * 3) Read reg 14 // Read MMD data
+ */
+static int phy_read_mmd_indirect(struct mii_bus *bus, int prtad, int devad,
+ int addr)
+{
+ u32 ret;
+
+ mmd_phy_indirect(bus, prtad, devad, addr);
+
+ /* Read the content of the MMD's selected register */
+ ret = bus->read(bus, addr, MII_MMD_DATA);
+
+ return ret;
+}
+
+/**
+ * phy_write_mmd_indirect - writes data to the MMD registers
+ * @bus: the target MII bus
+ * @prtad: MMD Address
+ * @devad: MMD DEVAD
+ * @addr: PHY address on the MII bus
+ * @data: data to write in the MMD register
+ *
+ * Description: Write data from the MMD registers of the specified
+ * phy address.
+ * To write these register we have:
+ * 1) Write reg 13 // DEVAD
+ * 2) Write reg 14 // MMD Address
+ * 3) Write reg 13 // MMD Data Command for MMD DEVAD
+ * 3) Write reg 14 // Write MMD data
+ */
+static void phy_write_mmd_indirect(struct mii_bus *bus, int prtad, int devad,
+ int addr, u32 data)
+{
+ mmd_phy_indirect(bus, prtad, devad, addr);
+
+ /* Write the data into MMD's selected register */
+ bus->write(bus, addr, MII_MMD_DATA, data);
+}
+
+static u32 phy_eee_to_adv(u16 eee_adv)
+{
+ u32 adv = 0;
+
+ if (eee_adv & MDIO_EEE_100TX)
+ adv |= ADVERTISED_100baseT_Full;
+ if (eee_adv & MDIO_EEE_1000T)
+ adv |= ADVERTISED_1000baseT_Full;
+ if (eee_adv & MDIO_EEE_10GT)
+ adv |= ADVERTISED_10000baseT_Full;
+ if (eee_adv & MDIO_EEE_1000KX)
+ adv |= ADVERTISED_1000baseKX_Full;
+ if (eee_adv & MDIO_EEE_10GKX4)
+ adv |= ADVERTISED_10000baseKX4_Full;
+ if (eee_adv & MDIO_EEE_10GKR)
+ adv |= ADVERTISED_10000baseKR_Full;
+
+ return adv;
+}
+
+static u32 phy_eee_to_supported(u16 eee_caported)
+{
+ u32 supported = 0;
+
+ if (eee_caported & MDIO_EEE_100TX)
+ supported |= SUPPORTED_100baseT_Full;
+ if (eee_caported & MDIO_EEE_1000T)
+ supported |= SUPPORTED_1000baseT_Full;
+ if (eee_caported & MDIO_EEE_10GT)
+ supported |= SUPPORTED_10000baseT_Full;
+ if (eee_caported & MDIO_EEE_1000KX)
+ supported |= SUPPORTED_1000baseKX_Full;
+ if (eee_caported & MDIO_EEE_10GKX4)
+ supported |= SUPPORTED_10000baseKX4_Full;
+ if (eee_caported & MDIO_EEE_10GKR)
+ supported |= SUPPORTED_10000baseKR_Full;
+
+ return supported;
+}
+
+static u16 phy_adv_to_eee(u32 adv)
+{
+ u16 reg = 0;
+
+ if (adv & ADVERTISED_100baseT_Full)
+ reg |= MDIO_EEE_100TX;
+ if (adv & ADVERTISED_1000baseT_Full)
+ reg |= MDIO_EEE_1000T;
+ if (adv & ADVERTISED_10000baseT_Full)
+ reg |= MDIO_EEE_10GT;
+ if (adv & ADVERTISED_1000baseKX_Full)
+ reg |= MDIO_EEE_1000KX;
+ if (adv & ADVERTISED_10000baseKX4_Full)
+ reg |= MDIO_EEE_10GKX4;
+ if (adv & ADVERTISED_10000baseKR_Full)
+ reg |= MDIO_EEE_10GKR;
+
+ return reg;
+}
+
+/**
+ * phy_init_eee - init and check the EEE feature
+ * @phydev: target phy_device struct
+ * @clk_stop_enable: PHY may stop the clock during LPI
+ *
+ * Description: it checks if the Energy-Efficient Ethernet (EEE)
+ * is supported by looking at the MMD registers 3.20 and 7.60/61
+ * and it programs the MMD register 3.0 setting the "Clock stop enable"
+ * bit if required.
+ */
+int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable)
+{
+ int ret = -EPROTONOSUPPORT;
+
+ /* According to 802.3az,the EEE is supported only in full duplex-mode.
+ * Also EEE feature is active when core is operating with MII, GMII
+ * or RGMII.
+ */
+ if ((phydev->duplex == DUPLEX_FULL) &&
+ ((phydev->interface == PHY_INTERFACE_MODE_MII) ||
+ (phydev->interface == PHY_INTERFACE_MODE_GMII) ||
+ (phydev->interface == PHY_INTERFACE_MODE_RGMII))) {
+ int eee_lp, eee_cap, eee_adv;
+ u32 lp, cap, adv;
+ int idx, status;
+
+ /* Read phy status to properly get the right settings */
+ status = phy_read_status(phydev);
+ if (status)
+ return status;
+
+ /* First check if the EEE ability is supported */
+ eee_cap = phy_read_mmd_indirect(phydev->bus, MDIO_PCS_EEE_ABLE,
+ MDIO_MMD_PCS, phydev->addr);
+ if (eee_cap < 0)
+ return eee_cap;
+
+ cap = phy_eee_to_supported(eee_cap);
+ if (!cap)
+ goto eee_exit;
+
+ /* Check which link settings negotiated and verify it in
+ * the EEE advertising registers.
+ */
+ eee_lp = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_LPABLE,
+ MDIO_MMD_AN, phydev->addr);
+ if (eee_lp < 0)
+ return eee_lp;
+
+ eee_adv = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_ADV,
+ MDIO_MMD_AN, phydev->addr);
+ if (eee_adv < 0)
+ return eee_adv;
+
+ adv = phy_eee_to_adv(eee_adv);
+ lp = phy_eee_to_adv(eee_lp);
+ idx = phy_find_setting(phydev->speed, phydev->duplex);
+ if ((lp & adv & settings[idx].setting))
+ goto eee_exit;
+
+ if (clk_stop_enable) {
+ /* Configure the PHY to stop receiving xMII
+ * clock while it is signaling LPI.
+ */
+ int val = phy_read_mmd_indirect(phydev->bus, MDIO_CTRL1,
+ MDIO_MMD_PCS,
+ phydev->addr);
+ if (val < 0)
+ return val;
+
+ val |= MDIO_PCS_CTRL1_CLKSTOP_EN;
+ phy_write_mmd_indirect(phydev->bus, MDIO_CTRL1,
+ MDIO_MMD_PCS, phydev->addr, val);
+ }
+
+ ret = 0; /* EEE supported */
+ }
+
+eee_exit:
+ return ret;
+}
+EXPORT_SYMBOL(phy_init_eee);
+
+/**
+ * phy_get_eee_err - report the EEE wake error count
+ * @phydev: target phy_device struct
+ *
+ * Description: it is to report the number of time where the PHY
+ * failed to complete its normal wake sequence.
+ */
+int phy_get_eee_err(struct phy_device *phydev)
+{
+ return phy_read_mmd_indirect(phydev->bus, MDIO_PCS_EEE_WK_ERR,
+ MDIO_MMD_PCS, phydev->addr);
+
+}
+EXPORT_SYMBOL(phy_get_eee_err);
+
+/**
+ * phy_ethtool_get_eee - get EEE supported and status
+ * @phydev: target phy_device struct
+ * @data: ethtool_eee data
+ *
+ * Description: it reportes the Supported/Advertisement/LP Advertisement
+ * capabilities.
+ */
+int phy_ethtool_get_eee(struct phy_device *phydev, struct ethtool_eee *data)
+{
+ int val;
+
+ /* Get Supported EEE */
+ val = phy_read_mmd_indirect(phydev->bus, MDIO_PCS_EEE_ABLE,
+ MDIO_MMD_PCS, phydev->addr);
+ if (val < 0)
+ return val;
+ data->supported = phy_eee_to_supported(val);
+
+ /* Get advertisement EEE */
+ val = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_ADV,
+ MDIO_MMD_AN, phydev->addr);
+ if (val < 0)
+ return val;
+ data->advertised = phy_eee_to_adv(val);
+
+ /* Get LP advertisement EEE */
+ val = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_LPABLE,
+ MDIO_MMD_AN, phydev->addr);
+ if (val < 0)
+ return val;
+ data->lp_advertised = phy_eee_to_adv(val);
+
+ return 0;
+}
+EXPORT_SYMBOL(phy_ethtool_get_eee);
+
+/**
+ * phy_ethtool_set_eee - set EEE supported and status
+ * @phydev: target phy_device struct
+ * @data: ethtool_eee data
+ *
+ * Description: it is to program the Advertisement EEE register.
+ */
+int phy_ethtool_set_eee(struct phy_device *phydev, struct ethtool_eee *data)
+{
+ int val;
+
+ val = phy_adv_to_eee(data->advertised);
+ phy_write_mmd_indirect(phydev->bus, MDIO_AN_EEE_ADV, MDIO_MMD_AN,
+ phydev->addr, val);
+
+ return 0;
+}
+EXPORT_SYMBOL(phy_ethtool_set_eee);
#define MDIO_PKGID2 15
#define MDIO_AN_ADVERTISE 16 /* AN advertising (base page) */
#define MDIO_AN_LPA 19 /* AN LP abilities (base page) */
+#define MDIO_PCS_EEE_ABLE 20 /* EEE Capability register */
+#define MDIO_PCS_EEE_WK_ERR 22 /* EEE wake error counter */
#define MDIO_PHYXS_LNSTAT 24 /* PHY XGXS lane state */
+#define MDIO_AN_EEE_ADV 60 /* EEE advertisement */
+#define MDIO_AN_EEE_LPABLE 61 /* EEE link partner ability */
/* Media-dependent registers. */
#define MDIO_PMA_10GBT_SWAPPOL 130 /* 10GBASE-T pair swap & polarity */
#define MDIO_PCS_10GBRT_STAT2 33 /* 10GBASE-R/-T PCS status 2 */
#define MDIO_AN_10GBT_CTRL 32 /* 10GBASE-T auto-negotiation control */
#define MDIO_AN_10GBT_STAT 33 /* 10GBASE-T auto-negotiation status */
-#define MDIO_AN_EEE_ADV 60 /* EEE advertisement */
/* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */
#define MDIO_PMA_LASI_RXCTRL 0x9000 /* RX_ALARM control */
#define MDIO_AN_CTRL1_RESTART BMCR_ANRESTART
#define MDIO_AN_CTRL1_ENABLE BMCR_ANENABLE
#define MDIO_AN_CTRL1_XNP 0x2000 /* Enable extended next page */
+#define MDIO_PCS_CTRL1_CLKSTOP_EN 0x400 /* Stop the clock during LPI */
/* 10 Gb/s */
#define MDIO_CTRL1_SPEED10G (MDIO_CTRL1_SPEEDSELEXT | 0x00)
#define MDIO_AN_10GBT_STAT_MS 0x4000 /* Master/slave config */
#define MDIO_AN_10GBT_STAT_MSFLT 0x8000 /* Master/slave config fault */
-/* AN EEE Advertisement register. */
-#define MDIO_AN_EEE_ADV_100TX 0x0002 /* Advertise 100TX EEE cap */
-#define MDIO_AN_EEE_ADV_1000T 0x0004 /* Advertise 1000T EEE cap */
+/* EEE Supported/Advertisement/LP Advertisement registers.
+ *
+ * EEE capability Register (3.20), Advertisement (7.60) and
+ * Link partner ability (7.61) registers have and can use the same identical
+ * bit masks.
+ */
+#define MDIO_AN_EEE_ADV_100TX 0x0002 /* Advertise 100TX EEE cap */
+#define MDIO_AN_EEE_ADV_1000T 0x0004 /* Advertise 1000T EEE cap */
+/* Note: the two defines above can be potentially used by the user-land
+ * and cannot remove them now.
+ * So, we define the new generic MDIO_EEE_100TX and MDIO_EEE_1000T macros
+ * using the previous ones (that can be considered obsolete).
+ */
+#define MDIO_EEE_100TX MDIO_AN_EEE_ADV_100TX /* 100TX EEE cap */
+#define MDIO_EEE_1000T MDIO_AN_EEE_ADV_1000T /* 1000T EEE cap */
+#define MDIO_EEE_10GT 0x0008 /* 10GT EEE cap */
+#define MDIO_EEE_1000KX 0x0010 /* 1000KX EEE cap */
+#define MDIO_EEE_10GKX4 0x0020 /* 10G KX4 EEE cap */
+#define MDIO_EEE_10GKR 0x0040 /* 10G KR EEE cap */
/* LASI RX_ALARM control/status registers. */
#define MDIO_PMA_LASI_RX_PHYXSLFLT 0x0001 /* PHY XS RX local fault */
projects / cascardo / linux.git / commitdiff