--- /dev/null
+Device tree bindings for Atmel capacitive touch device, typically
+an Atmel touch sensor connected to AtmegaXX MCU running firmware
+based on Qtouch library.
+
+The node for this device must be a child of a I2C controller node, as the
+device communicates via I2C.
+
+Required properties:
+
+ compatible: Must be "atmel,captouch".
+ reg: The I2C slave address of the device.
+ interrupts: Property describing the interrupt line the device
+ is connected to. The device only has one interrupt
+ source.
+ linux,keycodes: Specifies an array of numeric keycode values to
+ be used for reporting button presses. The array can
+ contain up to 8 entries.
+
+Optional properties:
+
+ autorepeat: Enables the Linux input system's autorepeat
+ feature on the input device.
+
+Example:
+
+ atmel-captouch@51 {
+ compatible = "atmel,captouch";
+ reg = <0x51>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+ linux,keycodes = <BTN_0>, <BTN_1>,
+ <BTN_2>, <BTN_3>,
+ <BTN_4>, <BTN_5>,
+ <BTN_6>, <BTN_7>;
+ autorepeat;
+ };
--- /dev/null
+Raydium I2C touchscreen
+
+Required properties:
+- compatible: must be "raydium,rm32380"
+- reg: The I2C address of the device
+- interrupt-parent: the phandle for the interrupt controller
+- interrupts: interrupt to which the chip is connected
+ See ../interrupt-controller/interrupts.txt
+Optional properties:
+- avdd-supply: analog power supply needed to power device
+- vccio-supply: IO Power source
+- reset-gpios: reset gpio the chip is connected to.
+
+Example:
+ touchscreen@39 {
+ compatible = "raydium,rm32380";
+ reg = <0x39>;
+ interrupt-parent = <&gpio>;
+ interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
+ };
- syna,reset-delay-ms: The number of milliseconds to wait after resetting the
device.
+- syna,startup-delay-ms: The number of milliseconds to wait after powering on
+ the device.
+
+- vdd-supply: VDD power supply.
+See ../regulator/regulator.txt
+
+- vio-supply: VIO power supply
+See ../regulator/regulator.txt
+
Function Parameters:
Parameters specific to RMI functions are contained in child nodes of the rmi device
node. Documentation for the parameters of each function can be found in:
ralink Mediatek/Ralink Technology Corp.
ramtron Ramtron International
raspberrypi Raspberry Pi Foundation
+raydium Raydium Semiconductor Corp.
realtek Realtek Semiconductor Corp.
renesas Renesas Electronics Corporation
richtek Richtek Technology Corporation
}
input_event(dev, EV_KEY, BTN_TOUCH, count > 0);
- if (use_count)
+
+ if (use_count) {
+ if (count == 0 &&
+ !test_bit(ABS_MT_DISTANCE, dev->absbit) &&
+ test_bit(ABS_DISTANCE, dev->absbit) &&
+ input_abs_get_val(dev, ABS_DISTANCE) != 0) {
+ /*
+ * Force reporting BTN_TOOL_FINGER for devices that
+ * only report general hover (and not per-contact
+ * distance) when contact is in proximity but not
+ * on the surface.
+ */
+ count = 1;
+ }
+
input_mt_report_finger_count(dev, count);
+ }
if (oldest) {
int x = input_mt_get_value(oldest, ABS_MT_POSITION_X);
rcu_read_unlock();
- add_input_randomness(vals->type, vals->code, vals->value);
-
/* trigger auto repeat for key events */
if (test_bit(EV_REP, dev->evbit) && test_bit(EV_KEY, dev->evbit)) {
for (v = vals; v != vals + count; v++) {
static void input_handle_event(struct input_dev *dev,
unsigned int type, unsigned int code, int value)
{
- int disposition;
+ int disposition = input_get_disposition(dev, type, code, &value);
- disposition = input_get_disposition(dev, type, code, &value);
+ if (disposition != INPUT_IGNORE_EVENT && type != EV_SYN)
+ add_input_randomness(type, code, value);
if ((disposition & INPUT_PASS_TO_DEVICE) && dev->event)
dev->event(dev, type, code, value);
#define TC3589x_PULL_DOWN_MASK 0x1
#define TC3589x_PULL_UP_MASK 0x2
#define TC3589x_PULLUP_ALL_MASK 0xAA
-#define TC3589x_IO_PULL_VAL(index, mask) ((mask)<<((index)%4)*2))
+#define TC3589x_IO_PULL_VAL(index, mask) ((mask)<<((index)%4)*2)
/* Bit masks for IOCFG register */
#define IOCFG_BALLCFG 0x01
if (!num_rows || !num_cols || ((num_rows + num_cols) > KBC_MAX_GPIO)) {
dev_err(kbc->dev,
- "keypad rows/columns not porperly specified\n");
+ "keypad rows/columns not properly specified\n");
return -EINVAL;
}
To compile this driver as a module, choose M here: the
module will be called arizona-haptics.
+config INPUT_ATMEL_CAPTOUCH
+ tristate "Atmel Capacitive Touch Button Driver"
+ depends on OF || COMPILE_TEST
+ depends on I2C
+ help
+ Say Y here if an Atmel Capacitive Touch Button device which
+ implements "captouch" protocol is connected to I2C bus. Typically
+ this device consists of Atmel Touch sensor controlled by AtMegaXX
+ MCU running firmware based on Qtouch library.
+ One should find "atmel,captouch" node in the board specific DTS.
+
+ To compile this driver as a module, choose M here: the
+ module will be called atmel_captouch.
+
config INPUT_BMA150
tristate "BMA150/SMB380 acceleration sensor support"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called drv2667-haptics.
+config INPUT_HISI_POWERKEY
+ tristate "Hisilicon PMIC ONKEY support"
+ depends on ARCH_HISI || COMPILE_TEST
+ help
+ Say Y to enable support for PMIC ONKEY.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hisi_powerkey.
+
endif
obj-$(CONFIG_INPUT_ARIZONA_HAPTICS) += arizona-haptics.o
obj-$(CONFIG_INPUT_ATI_REMOTE2) += ati_remote2.o
obj-$(CONFIG_INPUT_ATLAS_BTNS) += atlas_btns.o
+obj-$(CONFIG_INPUT_ATMEL_CAPTOUCH) += atmel_captouch.o
obj-$(CONFIG_INPUT_BFIN_ROTARY) += bfin_rotary.o
obj-$(CONFIG_INPUT_BMA150) += bma150.o
obj-$(CONFIG_INPUT_CM109) += cm109.o
obj-$(CONFIG_INPUT_GP2A) += gp2ap002a00f.o
obj-$(CONFIG_INPUT_GPIO_BEEPER) += gpio-beeper.o
obj-$(CONFIG_INPUT_GPIO_TILT_POLLED) += gpio_tilt_polled.o
+obj-$(CONFIG_INPUT_HISI_POWERKEY) += hisi_powerkey.o
obj-$(CONFIG_HP_SDC_RTC) += hp_sdc_rtc.o
obj-$(CONFIG_INPUT_IMS_PCU) += ims-pcu.o
obj-$(CONFIG_INPUT_IXP4XX_BEEPER) += ixp4xx-beeper.o
if (slave != i2c_addr) {
pr_notice(APANEL ": only one SMBus slave "
- "address supported, skiping device...\n");
+ "address supported, skipping device...\n");
continue;
}
--- /dev/null
+/*
+ * Atmel Atmegaxx Capacitive Touch Button Driver
+ *
+ * Copyright (C) 2016 Google, inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * It's irrelevant that the HW used to develop captouch driver is based
+ * on Atmega88PA part and uses QtouchADC parts for sensing touch.
+ * Calling this driver "captouch" is an arbitrary way to distinguish
+ * the protocol this driver supported by other atmel/qtouch drivers.
+ *
+ * Captouch driver supports a newer/different version of the I2C
+ * registers/commands than the qt1070.c driver.
+ * Don't let the similarity of the general driver structure fool you.
+ *
+ * For raw i2c access from userspace, use i2cset/i2cget
+ * to poke at /dev/i2c-N devices.
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+
+/* Maximum number of buttons supported */
+#define MAX_NUM_OF_BUTTONS 8
+
+/* Registers */
+#define REG_KEY1_THRESHOLD 0x02
+#define REG_KEY2_THRESHOLD 0x03
+#define REG_KEY3_THRESHOLD 0x04
+#define REG_KEY4_THRESHOLD 0x05
+
+#define REG_KEY1_REF_H 0x20
+#define REG_KEY1_REF_L 0x21
+#define REG_KEY2_REF_H 0x22
+#define REG_KEY2_REF_L 0x23
+#define REG_KEY3_REF_H 0x24
+#define REG_KEY3_REF_L 0x25
+#define REG_KEY4_REF_H 0x26
+#define REG_KEY4_REF_L 0x27
+
+#define REG_KEY1_DLT_H 0x30
+#define REG_KEY1_DLT_L 0x31
+#define REG_KEY2_DLT_H 0x32
+#define REG_KEY2_DLT_L 0x33
+#define REG_KEY3_DLT_H 0x34
+#define REG_KEY3_DLT_L 0x35
+#define REG_KEY4_DLT_H 0x36
+#define REG_KEY4_DLT_L 0x37
+
+#define REG_KEY_STATE 0x3C
+
+/*
+ * @i2c_client: I2C slave device client pointer
+ * @input: Input device pointer
+ * @num_btn: Number of buttons
+ * @keycodes: map of button# to KeyCode
+ * @prev_btn: Previous key state to detect button "press" or "release"
+ * @xfer_buf: I2C transfer buffer
+ */
+struct atmel_captouch_device {
+ struct i2c_client *client;
+ struct input_dev *input;
+ u32 num_btn;
+ u32 keycodes[MAX_NUM_OF_BUTTONS];
+ u8 prev_btn;
+ u8 xfer_buf[8] ____cacheline_aligned;
+};
+
+/*
+ * Read from I2C slave device
+ * The protocol is that the client has to provide both the register address
+ * and the length, and while reading back the device would prepend the data
+ * with address and length for verification.
+ */
+static int atmel_read(struct atmel_captouch_device *capdev,
+ u8 reg, u8 *data, size_t len)
+{
+ struct i2c_client *client = capdev->client;
+ struct device *dev = &client->dev;
+ struct i2c_msg msg[2];
+ int err;
+
+ if (len > sizeof(capdev->xfer_buf) - 2)
+ return -EINVAL;
+
+ capdev->xfer_buf[0] = reg;
+ capdev->xfer_buf[1] = len;
+
+ msg[0].addr = client->addr;
+ msg[0].flags = 0;
+ msg[0].buf = capdev->xfer_buf;
+ msg[0].len = 2;
+
+ msg[1].addr = client->addr;
+ msg[1].flags = I2C_M_RD;
+ msg[1].buf = capdev->xfer_buf;
+ msg[1].len = len + 2;
+
+ err = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+ if (err != ARRAY_SIZE(msg))
+ return err < 0 ? err : -EIO;
+
+ if (capdev->xfer_buf[0] != reg) {
+ dev_err(dev,
+ "I2C read error: register address does not match (%#02x vs %02x)\n",
+ capdev->xfer_buf[0], reg);
+ return -ECOMM;
+ }
+
+ memcpy(data, &capdev->xfer_buf[2], len);
+
+ return 0;
+}
+
+/*
+ * Handle interrupt and report the key changes to the input system.
+ * Multi-touch can be supported; however, it really depends on whether
+ * the device can multi-touch.
+ */
+static irqreturn_t atmel_captouch_isr(int irq, void *data)
+{
+ struct atmel_captouch_device *capdev = data;
+ struct device *dev = &capdev->client->dev;
+ int error;
+ int i;
+ u8 new_btn;
+ u8 changed_btn;
+
+ error = atmel_read(capdev, REG_KEY_STATE, &new_btn, 1);
+ if (error) {
+ dev_err(dev, "failed to read button state: %d\n", error);
+ goto out;
+ }
+
+ dev_dbg(dev, "%s: button state %#02x\n", __func__, new_btn);
+
+ changed_btn = new_btn ^ capdev->prev_btn;
+ capdev->prev_btn = new_btn;
+
+ for (i = 0; i < capdev->num_btn; i++) {
+ if (changed_btn & BIT(i))
+ input_report_key(capdev->input,
+ capdev->keycodes[i],
+ new_btn & BIT(i));
+ }
+
+ input_sync(capdev->input);
+
+out:
+ return IRQ_HANDLED;
+}
+
+/*
+ * Probe function to setup the device, input system and interrupt
+ */
+static int atmel_captouch_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct atmel_captouch_device *capdev;
+ struct device *dev = &client->dev;
+ struct device_node *node;
+ int i;
+ int err;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_WORD_DATA |
+ I2C_FUNC_SMBUS_I2C_BLOCK)) {
+ dev_err(dev, "needed i2c functionality is not supported\n");
+ return -EINVAL;
+ }
+
+ capdev = devm_kzalloc(dev, sizeof(*capdev), GFP_KERNEL);
+ if (!capdev)
+ return -ENOMEM;
+
+ capdev->client = client;
+ i2c_set_clientdata(client, capdev);
+
+ err = atmel_read(capdev, REG_KEY_STATE,
+ &capdev->prev_btn, sizeof(capdev->prev_btn));
+ if (err) {
+ dev_err(dev, "failed to read initial button state: %d\n", err);
+ return err;
+ }
+
+ capdev->input = devm_input_allocate_device(dev);
+ if (!capdev->input) {
+ dev_err(dev, "failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ capdev->input->id.bustype = BUS_I2C;
+ capdev->input->id.product = 0x880A;
+ capdev->input->id.version = 0;
+ capdev->input->name = "ATMegaXX Capacitive Button Controller";
+ __set_bit(EV_KEY, capdev->input->evbit);
+
+ node = dev->of_node;
+ if (!node) {
+ dev_err(dev, "failed to find matching node in device tree\n");
+ return -EINVAL;
+ }
+
+ if (of_property_read_bool(node, "autorepeat"))
+ __set_bit(EV_REP, capdev->input->evbit);
+
+ capdev->num_btn = of_property_count_u32_elems(node, "linux,keymap");
+ if (capdev->num_btn > MAX_NUM_OF_BUTTONS)
+ capdev->num_btn = MAX_NUM_OF_BUTTONS;
+
+ err = of_property_read_u32_array(node, "linux,keycodes",
+ capdev->keycodes,
+ capdev->num_btn);
+ if (err) {
+ dev_err(dev,
+ "failed to read linux,keycode property: %d\n", err);
+ return err;
+ }
+
+ for (i = 0; i < capdev->num_btn; i++)
+ __set_bit(capdev->keycodes[i], capdev->input->keybit);
+
+ capdev->input->keycode = capdev->keycodes;
+ capdev->input->keycodesize = sizeof(capdev->keycodes[0]);
+ capdev->input->keycodemax = capdev->num_btn;
+
+ err = input_register_device(capdev->input);
+ if (err)
+ return err;
+
+ err = devm_request_threaded_irq(dev, client->irq,
+ NULL, atmel_captouch_isr,
+ IRQF_ONESHOT,
+ "atmel_captouch", capdev);
+ if (err) {
+ dev_err(dev, "failed to request irq %d: %d\n",
+ client->irq, err);
+ return err;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id atmel_captouch_of_id[] = {
+ {
+ .compatible = "atmel,captouch",
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_captouch_of_id);
+#endif
+
+static const struct i2c_device_id atmel_captouch_id[] = {
+ { "atmel_captouch", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, atmel_captouch_id);
+
+static struct i2c_driver atmel_captouch_driver = {
+ .probe = atmel_captouch_probe,
+ .id_table = atmel_captouch_id,
+ .driver = {
+ .name = "atmel_captouch",
+ .of_match_table = of_match_ptr(atmel_captouch_of_id),
+ },
+};
+module_i2c_driver(atmel_captouch_driver);
+
+/* Module information */
+MODULE_AUTHOR("Hung-yu Wu <hywu@google.com>");
+MODULE_DESCRIPTION("Atmel ATmegaXX Capacitance Touch Sensor I2C Driver");
+MODULE_LICENSE("GPL v2");
--- /dev/null
+/*
+ * Hisilicon PMIC powerkey driver
+ *
+ * Copyright (C) 2013 Hisilicon Ltd.
+ * Copyright (C) 2015, 2016 Linaro Ltd.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/reboot.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+
+/* the held interrupt will trigger after 4 seconds */
+#define MAX_HELD_TIME (4 * MSEC_PER_SEC)
+
+static irqreturn_t hi65xx_power_press_isr(int irq, void *q)
+{
+ struct input_dev *input = q;
+
+ pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+ input_report_key(input, KEY_POWER, 1);
+ input_sync(input);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t hi65xx_power_release_isr(int irq, void *q)
+{
+ struct input_dev *input = q;
+
+ pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+ input_report_key(input, KEY_POWER, 0);
+ input_sync(input);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t hi65xx_restart_toggle_isr(int irq, void *q)
+{
+ struct input_dev *input = q;
+ int value = test_bit(KEY_RESTART, input->key);
+
+ pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+ input_report_key(input, KEY_RESTART, !value);
+ input_sync(input);
+
+ return IRQ_HANDLED;
+}
+
+static const struct {
+ const char *name;
+ irqreturn_t (*handler)(int irq, void *q);
+} hi65xx_irq_info[] = {
+ { "down", hi65xx_power_press_isr },
+ { "up", hi65xx_power_release_isr },
+ { "hold 4s", hi65xx_restart_toggle_isr },
+};
+
+static int hi65xx_powerkey_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct input_dev *input;
+ int irq, i, error;
+
+ input = devm_input_allocate_device(&pdev->dev);
+ if (!input) {
+ dev_err(&pdev->dev, "failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ input->phys = "hisi_on/input0";
+ input->name = "HISI 65xx PowerOn Key";
+
+ input_set_capability(input, EV_KEY, KEY_POWER);
+ input_set_capability(input, EV_KEY, KEY_RESTART);
+
+ for (i = 0; i < ARRAY_SIZE(hi65xx_irq_info); i++) {
+
+ irq = platform_get_irq_byname(pdev, hi65xx_irq_info[i].name);
+ if (irq < 0) {
+ error = irq;
+ dev_err(dev, "couldn't get irq %s: %d\n",
+ hi65xx_irq_info[i].name, error);
+ return error;
+ }
+
+ error = devm_request_any_context_irq(dev, irq,
+ hi65xx_irq_info[i].handler,
+ IRQF_ONESHOT,
+ hi65xx_irq_info[i].name,
+ input);
+ if (error < 0) {
+ dev_err(dev, "couldn't request irq %s: %d\n",
+ hi65xx_irq_info[i].name, error);
+ return error;
+ }
+ }
+
+ error = input_register_device(input);
+ if (error) {
+ dev_err(&pdev->dev, "failed to register input device: %d\n",
+ error);
+ return error;
+ }
+
+ device_init_wakeup(&pdev->dev, 1);
+
+ return 0;
+}
+
+static int hi65xx_powerkey_remove(struct platform_device *pdev)
+{
+ device_init_wakeup(&pdev->dev, 0);
+
+ return 0;
+}
+
+static struct platform_driver hi65xx_powerkey_driver = {
+ .driver = {
+ .name = "hi65xx-powerkey",
+ },
+ .probe = hi65xx_powerkey_probe,
+ .remove = hi65xx_powerkey_remove,
+};
+module_platform_driver(hi65xx_powerkey_driver);
+
+MODULE_AUTHOR("Zhiliang Xue <xuezhiliang@huawei.com");
+MODULE_DESCRIPTION("Hisi PMIC Power key driver");
+MODULE_LICENSE("GPL v2");
node = dev->of_node;
if(!node) {
- dev_err(dev, "Missing dveice tree data\n");
+ dev_err(dev, "Missing device tree data\n");
return -EINVAL;
}
if (xenbus_scanf(XBT_NIL, dev->otherend, "feature-abs-pointer", "%d", &abs) < 0)
abs = 0;
if (abs) {
- ret = xenbus_printf(XBT_NIL, dev->nodename,
- "request-abs-pointer", "1");
+ ret = xenbus_write(XBT_NIL, dev->nodename,
+ "request-abs-pointer", "1");
if (ret) {
pr_warning("xenkbd: can't request abs-pointer");
abs = 0;
if (ret < 0)
val = 0;
if (val) {
- ret = xenbus_printf(XBT_NIL, info->xbdev->nodename,
- "request-abs-pointer", "1");
+ ret = xenbus_write(XBT_NIL, info->xbdev->nodename,
+ "request-abs-pointer", "1");
if (ret)
pr_warning("xenkbd: can't request abs-pointer");
}
snprintf(etd->tp_phys, sizeof(etd->tp_phys), "%s/input1",
psmouse->ps2dev.serio->phys);
tp_dev->phys = etd->tp_phys;
- tp_dev->name = "Elantech PS/2 TrackPoint";
+ tp_dev->name = "ETPS/2 Elantech TrackPoint";
tp_dev->id.bustype = BUS_I8042;
tp_dev->id.vendor = 0x0002;
tp_dev->id.product = PSMOUSE_ELANTECH;
"%s/input1", psmouse->ps2dev.serio->phys);
dev2->phys = priv->phys;
- dev2->name = "PS/2 Touchpad";
+ dev2->name = "LBPS/2 Fujitsu Lifebook Touchpad";
dev2->id.bustype = BUS_I8042;
dev2->id.vendor = 0x0002;
dev2->id.product = PSMOUSE_LIFEBOOK;
* This bit disables whatever sleep mode may be selected by the sleep_mode
* field and forces the device to run at full power without sleeping.
*/
-#define RMI_F01_CRTL0_NOSLEEP_BIT BIT(2)
+#define RMI_F01_CTRL0_NOSLEEP_BIT BIT(2)
/*
* When this bit is set, the touch controller employs a noise-filtering
* algorithm designed for use with a connected battery charger.
*/
-#define RMI_F01_CRTL0_CHARGER_BIT BIT(5)
+#define RMI_F01_CTRL0_CHARGER_BIT BIT(5)
/*
* Sets the report rate for the device. The effect of this setting is
* highly product dependent. Check the spec sheet for your particular
* touch sensor.
*/
-#define RMI_F01_CRTL0_REPORTRATE_BIT BIT(6)
+#define RMI_F01_CTRL0_REPORTRATE_BIT BIT(6)
/*
* Written by the host as an indicator that the device has been
* successfully configured.
*/
-#define RMI_F01_CRTL0_CONFIGURED_BIT BIT(7)
+#define RMI_F01_CTRL0_CONFIGURED_BIT BIT(7)
/**
* @ctrl0 - see the bit definitions above.
case RMI_F01_NOSLEEP_DEFAULT:
break;
case RMI_F01_NOSLEEP_OFF:
- f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+ f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_NOSLEEP_BIT;
break;
case RMI_F01_NOSLEEP_ON:
- f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+ f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
break;
}
f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
}
- f01->device_control.ctrl0 |= RMI_F01_CRTL0_CONFIGURED_BIT;
+ f01->device_control.ctrl0 |= RMI_F01_CTRL0_CONFIGURED_BIT;
error = rmi_write(rmi_dev, fn->fd.control_base_addr,
f01->device_control.ctrl0);
int error;
f01->old_nosleep =
- f01->device_control.ctrl0 & RMI_F01_CRTL0_NOSLEEP_BIT;
- f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+ f01->device_control.ctrl0 & RMI_F01_CTRL0_NOSLEEP_BIT;
+ f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_NOSLEEP_BIT;
f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
if (device_may_wakeup(fn->rmi_dev->xport->dev))
if (error) {
dev_err(&fn->dev, "Failed to write sleep mode: %d.\n", error);
if (f01->old_nosleep)
- f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+ f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
return error;
int error;
if (f01->old_nosleep)
- f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+ f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
struct f11_2d_data *data = &f11->data;
s8 x, y;
- x = data->rel_pos[n_finger * 2];
- y = data->rel_pos[n_finger * 2 + 1];
+ x = data->rel_pos[n_finger * RMI_F11_REL_BYTES];
+ y = data->rel_pos[n_finger * RMI_F11_REL_BYTES + 1];
rmi_2d_sensor_rel_report(sensor, x, y);
}
struct rmi_driver_data *drvdata = dev_get_drvdata(&rmi_dev->dev);
struct f11_data *f11 = dev_get_drvdata(&fn->dev);
u16 data_base_addr = fn->fd.data_base_addr;
- u16 data_base_addr_offset = 0;
int error;
if (rmi_dev->xport->attn_data) {
rmi_dev->xport->attn_size -= f11->sensor.attn_size;
} else {
error = rmi_read_block(rmi_dev,
- data_base_addr + data_base_addr_offset,
- f11->sensor.data_pkt,
+ data_base_addr, f11->sensor.data_pkt,
f11->sensor.pkt_size);
if (error < 0)
return error;
rmi_f11_finger_handler(f11, &f11->sensor, irq_bits,
drvdata->num_of_irq_regs);
- data_base_addr_offset += f11->sensor.pkt_size;
return 0;
}
};
struct f12_data {
- struct rmi_function *fn;
struct rmi_2d_sensor sensor;
struct rmi_2d_sensor_platform_data sensor_pdata;
#include <linux/rmi.h>
#include <linux/irq.h>
#include <linux/of.h>
+#include <linux/delay.h>
+#include <linux/regulator/consumer.h>
#include "rmi_driver.h"
#define BUFFER_SIZE_INCREMENT 32
u8 *tx_buf;
size_t tx_buf_size;
+
+ struct regulator_bulk_data supplies[2];
+ u32 startup_delay;
};
#define RMI_PAGE_SELECT_REGISTER 0xff
return -ENODEV;
}
+ rmi_i2c->supplies[0].supply = "vdd";
+ rmi_i2c->supplies[1].supply = "vio";
+ retval = devm_regulator_bulk_get(&client->dev,
+ ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
+ if (retval < 0)
+ return retval;
+
+ retval = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
+ if (retval < 0)
+ return retval;
+
+ of_property_read_u32(client->dev.of_node, "syna,startup-delay-ms",
+ &rmi_i2c->startup_delay);
+
+ msleep(rmi_i2c->startup_delay);
+
rmi_i2c->client = client;
mutex_init(&rmi_i2c->page_mutex);
struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
rmi_unregister_transport_device(&rmi_i2c->xport);
+ regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
return 0;
}
dev_warn(dev, "Failed to enable irq for wake: %d\n",
ret);
}
+
+ regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
+
return ret;
}
struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
int ret;
+ ret = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
+ if (ret)
+ return ret;
+
+ msleep(rmi_i2c->startup_delay);
+
enable_irq(rmi_i2c->irq);
if (device_may_wakeup(&client->dev)) {
ret = disable_irq_wake(rmi_i2c->irq);
disable_irq(rmi_i2c->irq);
+ regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
+
return 0;
}
struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
int ret;
+ ret = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
+ if (ret)
+ return ret;
+
+ msleep(rmi_i2c->startup_delay);
+
enable_irq(rmi_i2c->irq);
ret = rmi_driver_resume(rmi_i2c->xport.rmi_dev);
/* it should be odd */
if (!(parity & 0x01)) {
dev_warn(&ams_delta_serio->dev,
- "paritiy check failed, data=0x%X parity=0x%X\n",
+ "parity check failed, data=0x%X parity=0x%X\n",
data, parity);
return SERIO_PARITY;
}
To compile this driver as a module, choose M here: the
module will be called kbtab.
+config TABLET_USB_PEGASUS
+ tristate "Pegasus Mobile Notetaker Pen input tablet support"
+ depends on USB_ARCH_HAS_HCD
+ select USB
+ help
+ Say Y here if you want to use the Pegasus Mobile Notetaker,
+ also known as:
+ Genie e-note The Notetaker,
+ Staedtler Digital ballpoint pen 990 01,
+ IRISnotes Express or
+ NEWLink Digital Note Taker.
+
+ To compile this driver as a module, choose M here: the
+ module will be called pegasus_notetaker.
+
config TABLET_SERIAL_WACOM4
tristate "Wacom protocol 4 serial tablet support"
select SERIO
obj-$(CONFIG_TABLET_USB_GTCO) += gtco.o
obj-$(CONFIG_TABLET_USB_HANWANG) += hanwang.o
obj-$(CONFIG_TABLET_USB_KBTAB) += kbtab.o
+obj-$(CONFIG_TABLET_USB_PEGASUS) += pegasus_notetaker.o
obj-$(CONFIG_TABLET_SERIAL_WACOM4) += wacom_serial4.o
--- /dev/null
+/*
+ * Pegasus Mobile Notetaker Pen input tablet driver
+ *
+ * Copyright (c) 2016 Martin Kepplinger <martink@posteo.de>
+ */
+
+/*
+ * request packet (control endpoint):
+ * |-------------------------------------|
+ * | Report ID | Nr of bytes | command |
+ * | (1 byte) | (1 byte) | (n bytes) |
+ * |-------------------------------------|
+ * | 0x02 | n | |
+ * |-------------------------------------|
+ *
+ * data packet after set xy mode command, 0x80 0xb5 0x02 0x01
+ * and pen is in range:
+ *
+ * byte byte name value (bits)
+ * --------------------------------------------
+ * 0 status 0 1 0 0 0 0 X X
+ * 1 color 0 0 0 0 H 0 S T
+ * 2 X low
+ * 3 X high
+ * 4 Y low
+ * 5 Y high
+ *
+ * X X battery state:
+ * no state reported 0x00
+ * battery low 0x01
+ * battery good 0x02
+ *
+ * H Hovering
+ * S Switch 1 (pen button)
+ * T Tip
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/input.h>
+#include <linux/usb/input.h>
+#include <linux/slab.h>
+
+/* USB HID defines */
+#define USB_REQ_GET_REPORT 0x01
+#define USB_REQ_SET_REPORT 0x09
+
+#define USB_VENDOR_ID_PEGASUSTECH 0x0e20
+#define USB_DEVICE_ID_PEGASUS_NOTETAKER_EN100 0x0101
+
+/* device specific defines */
+#define NOTETAKER_REPORT_ID 0x02
+#define NOTETAKER_SET_CMD 0x80
+#define NOTETAKER_SET_MODE 0xb5
+
+#define NOTETAKER_LED_MOUSE 0x02
+#define PEN_MODE_XY 0x01
+
+#define SPECIAL_COMMAND 0x80
+#define BUTTON_PRESSED 0xb5
+#define COMMAND_VERSION 0xa9
+
+/* in xy data packet */
+#define BATTERY_NO_REPORT 0x40
+#define BATTERY_LOW 0x41
+#define BATTERY_GOOD 0x42
+#define PEN_BUTTON_PRESSED BIT(1)
+#define PEN_TIP BIT(0)
+
+struct pegasus {
+ unsigned char *data;
+ u8 data_len;
+ dma_addr_t data_dma;
+ struct input_dev *dev;
+ struct usb_device *usbdev;
+ struct usb_interface *intf;
+ struct urb *irq;
+ char name[128];
+ char phys[64];
+ struct work_struct init;
+};
+
+static int pegasus_control_msg(struct pegasus *pegasus, u8 *data, int len)
+{
+ const int sizeof_buf = len + 2;
+ int result;
+ int error;
+ u8 *cmd_buf;
+
+ cmd_buf = kmalloc(sizeof_buf, GFP_KERNEL);
+ if (!cmd_buf)
+ return -ENOMEM;
+
+ cmd_buf[0] = NOTETAKER_REPORT_ID;
+ cmd_buf[1] = len;
+ memcpy(cmd_buf + 2, data, len);
+
+ result = usb_control_msg(pegasus->usbdev,
+ usb_sndctrlpipe(pegasus->usbdev, 0),
+ USB_REQ_SET_REPORT,
+ USB_TYPE_VENDOR | USB_DIR_OUT,
+ 0, 0, cmd_buf, sizeof_buf,
+ USB_CTRL_SET_TIMEOUT);
+
+ kfree(cmd_buf);
+
+ if (unlikely(result != sizeof_buf)) {
+ error = result < 0 ? result : -EIO;
+ dev_err(&pegasus->usbdev->dev, "control msg error: %d\n",
+ error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int pegasus_set_mode(struct pegasus *pegasus, u8 mode, u8 led)
+{
+ u8 cmd[] = { NOTETAKER_SET_CMD, NOTETAKER_SET_MODE, led, mode };
+
+ return pegasus_control_msg(pegasus, cmd, sizeof(cmd));
+}
+
+static void pegasus_parse_packet(struct pegasus *pegasus)
+{
+ unsigned char *data = pegasus->data;
+ struct input_dev *dev = pegasus->dev;
+ u16 x, y;
+
+ switch (data[0]) {
+ case SPECIAL_COMMAND:
+ /* device button pressed */
+ if (data[1] == BUTTON_PRESSED)
+ schedule_work(&pegasus->init);
+
+ break;
+
+ /* xy data */
+ case BATTERY_LOW:
+ dev_warn_once(&dev->dev, "Pen battery low\n");
+ /* fall through */
+
+ case BATTERY_NO_REPORT:
+ case BATTERY_GOOD:
+ x = le16_to_cpup((__le16 *)&data[2]);
+ y = le16_to_cpup((__le16 *)&data[4]);
+
+ /* pen-up event */
+ if (x == 0 && y == 0)
+ break;
+
+ input_report_key(dev, BTN_TOUCH, data[1] & PEN_TIP);
+ input_report_key(dev, BTN_RIGHT, data[1] & PEN_BUTTON_PRESSED);
+ input_report_key(dev, BTN_TOOL_PEN, 1);
+ input_report_abs(dev, ABS_X, (s16)x);
+ input_report_abs(dev, ABS_Y, y);
+
+ input_sync(dev);
+ break;
+
+ default:
+ dev_warn_once(&pegasus->usbdev->dev,
+ "unknown answer from device\n");
+ }
+}
+
+static void pegasus_irq(struct urb *urb)
+{
+ struct pegasus *pegasus = urb->context;
+ struct usb_device *dev = pegasus->usbdev;
+ int retval;
+
+ switch (urb->status) {
+ case 0:
+ pegasus_parse_packet(pegasus);
+ usb_mark_last_busy(pegasus->usbdev);
+ break;
+
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ dev_err(&dev->dev, "%s - urb shutting down with status: %d",
+ __func__, urb->status);
+ return;
+
+ default:
+ dev_err(&dev->dev, "%s - nonzero urb status received: %d",
+ __func__, urb->status);
+ break;
+ }
+
+ retval = usb_submit_urb(urb, GFP_ATOMIC);
+ if (retval)
+ dev_err(&dev->dev, "%s - usb_submit_urb failed with result %d",
+ __func__, retval);
+}
+
+static void pegasus_init(struct work_struct *work)
+{
+ struct pegasus *pegasus = container_of(work, struct pegasus, init);
+ int error;
+
+ error = pegasus_set_mode(pegasus, PEN_MODE_XY, NOTETAKER_LED_MOUSE);
+ if (error)
+ dev_err(&pegasus->usbdev->dev, "pegasus_set_mode error: %d\n",
+ error);
+}
+
+static int pegasus_open(struct input_dev *dev)
+{
+ struct pegasus *pegasus = input_get_drvdata(dev);
+ int error;
+
+ error = usb_autopm_get_interface(pegasus->intf);
+ if (error)
+ return error;
+
+ pegasus->irq->dev = pegasus->usbdev;
+ if (usb_submit_urb(pegasus->irq, GFP_KERNEL)) {
+ error = -EIO;
+ goto err_autopm_put;
+ }
+
+ error = pegasus_set_mode(pegasus, PEN_MODE_XY, NOTETAKER_LED_MOUSE);
+ if (error)
+ goto err_kill_urb;
+
+ return 0;
+
+err_kill_urb:
+ usb_kill_urb(pegasus->irq);
+ cancel_work_sync(&pegasus->init);
+err_autopm_put:
+ usb_autopm_put_interface(pegasus->intf);
+ return error;
+}
+
+static void pegasus_close(struct input_dev *dev)
+{
+ struct pegasus *pegasus = input_get_drvdata(dev);
+
+ usb_kill_urb(pegasus->irq);
+ cancel_work_sync(&pegasus->init);
+ usb_autopm_put_interface(pegasus->intf);
+}
+
+static int pegasus_probe(struct usb_interface *intf,
+ const struct usb_device_id *id)
+{
+ struct usb_device *dev = interface_to_usbdev(intf);
+ struct usb_endpoint_descriptor *endpoint;
+ struct pegasus *pegasus;
+ struct input_dev *input_dev;
+ int error;
+ int pipe;
+
+ /* We control interface 0 */
+ if (intf->cur_altsetting->desc.bInterfaceNumber >= 1)
+ return -ENODEV;
+
+ /* Sanity check that the device has an endpoint */
+ if (intf->altsetting[0].desc.bNumEndpoints < 1) {
+ dev_err(&intf->dev, "Invalid number of endpoints\n");
+ return -EINVAL;
+ }
+
+ endpoint = &intf->cur_altsetting->endpoint[0].desc;
+
+ pegasus = kzalloc(sizeof(*pegasus), GFP_KERNEL);
+ input_dev = input_allocate_device();
+ if (!pegasus || !input_dev) {
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ pegasus->usbdev = dev;
+ pegasus->dev = input_dev;
+ pegasus->intf = intf;
+
+ pipe = usb_rcvintpipe(dev, endpoint->bEndpointAddress);
+ pegasus->data_len = usb_maxpacket(dev, pipe, usb_pipeout(pipe));
+
+ pegasus->data = usb_alloc_coherent(dev, pegasus->data_len, GFP_KERNEL,
+ &pegasus->data_dma);
+ if (!pegasus->data) {
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ pegasus->irq = usb_alloc_urb(0, GFP_KERNEL);
+ if (!pegasus->irq) {
+ error = -ENOMEM;
+ goto err_free_dma;
+ }
+
+ usb_fill_int_urb(pegasus->irq, dev, pipe,
+ pegasus->data, pegasus->data_len,
+ pegasus_irq, pegasus, endpoint->bInterval);
+
+ pegasus->irq->transfer_dma = pegasus->data_dma;
+ pegasus->irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+
+ if (dev->manufacturer)
+ strlcpy(pegasus->name, dev->manufacturer,
+ sizeof(pegasus->name));
+
+ if (dev->product) {
+ if (dev->manufacturer)
+ strlcat(pegasus->name, " ", sizeof(pegasus->name));
+ strlcat(pegasus->name, dev->product, sizeof(pegasus->name));
+ }
+
+ if (!strlen(pegasus->name))
+ snprintf(pegasus->name, sizeof(pegasus->name),
+ "USB Pegasus Device %04x:%04x",
+ le16_to_cpu(dev->descriptor.idVendor),
+ le16_to_cpu(dev->descriptor.idProduct));
+
+ usb_make_path(dev, pegasus->phys, sizeof(pegasus->phys));
+ strlcat(pegasus->phys, "/input0", sizeof(pegasus->phys));
+
+ INIT_WORK(&pegasus->init, pegasus_init);
+
+ usb_set_intfdata(intf, pegasus);
+
+ input_dev->name = pegasus->name;
+ input_dev->phys = pegasus->phys;
+ usb_to_input_id(dev, &input_dev->id);
+ input_dev->dev.parent = &intf->dev;
+
+ input_set_drvdata(input_dev, pegasus);
+
+ input_dev->open = pegasus_open;
+ input_dev->close = pegasus_close;
+
+ __set_bit(EV_ABS, input_dev->evbit);
+ __set_bit(EV_KEY, input_dev->evbit);
+
+ __set_bit(ABS_X, input_dev->absbit);
+ __set_bit(ABS_Y, input_dev->absbit);
+
+ __set_bit(BTN_TOUCH, input_dev->keybit);
+ __set_bit(BTN_RIGHT, input_dev->keybit);
+ __set_bit(BTN_TOOL_PEN, input_dev->keybit);
+
+ __set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
+ __set_bit(INPUT_PROP_POINTER, input_dev->propbit);
+
+ input_set_abs_params(input_dev, ABS_X, -1500, 1500, 8, 0);
+ input_set_abs_params(input_dev, ABS_Y, 1600, 3000, 8, 0);
+
+ error = input_register_device(pegasus->dev);
+ if (error)
+ goto err_free_urb;
+
+ return 0;
+
+err_free_urb:
+ usb_free_urb(pegasus->irq);
+err_free_dma:
+ usb_free_coherent(dev, pegasus->data_len,
+ pegasus->data, pegasus->data_dma);
+err_free_mem:
+ input_free_device(input_dev);
+ kfree(pegasus);
+ usb_set_intfdata(intf, NULL);
+
+ return error;
+}
+
+static void pegasus_disconnect(struct usb_interface *intf)
+{
+ struct pegasus *pegasus = usb_get_intfdata(intf);
+
+ input_unregister_device(pegasus->dev);
+
+ usb_free_urb(pegasus->irq);
+ usb_free_coherent(interface_to_usbdev(intf),
+ pegasus->data_len, pegasus->data,
+ pegasus->data_dma);
+
+ kfree(pegasus);
+ usb_set_intfdata(intf, NULL);
+}
+
+static int pegasus_suspend(struct usb_interface *intf, pm_message_t message)
+{
+ struct pegasus *pegasus = usb_get_intfdata(intf);
+
+ mutex_lock(&pegasus->dev->mutex);
+ usb_kill_urb(pegasus->irq);
+ cancel_work_sync(&pegasus->init);
+ mutex_unlock(&pegasus->dev->mutex);
+
+ return 0;
+}
+
+static int pegasus_resume(struct usb_interface *intf)
+{
+ struct pegasus *pegasus = usb_get_intfdata(intf);
+ int retval = 0;
+
+ mutex_lock(&pegasus->dev->mutex);
+ if (pegasus->dev->users && usb_submit_urb(pegasus->irq, GFP_NOIO) < 0)
+ retval = -EIO;
+ mutex_unlock(&pegasus->dev->mutex);
+
+ return retval;
+}
+
+static int pegasus_reset_resume(struct usb_interface *intf)
+{
+ struct pegasus *pegasus = usb_get_intfdata(intf);
+ int retval = 0;
+
+ mutex_lock(&pegasus->dev->mutex);
+ if (pegasus->dev->users) {
+ retval = pegasus_set_mode(pegasus, PEN_MODE_XY,
+ NOTETAKER_LED_MOUSE);
+ if (!retval && usb_submit_urb(pegasus->irq, GFP_NOIO) < 0)
+ retval = -EIO;
+ }
+ mutex_unlock(&pegasus->dev->mutex);
+
+ return retval;
+}
+
+static const struct usb_device_id pegasus_ids[] = {
+ { USB_DEVICE(USB_VENDOR_ID_PEGASUSTECH,
+ USB_DEVICE_ID_PEGASUS_NOTETAKER_EN100) },
+ { }
+};
+MODULE_DEVICE_TABLE(usb, pegasus_ids);
+
+static struct usb_driver pegasus_driver = {
+ .name = "pegasus_notetaker",
+ .probe = pegasus_probe,
+ .disconnect = pegasus_disconnect,
+ .suspend = pegasus_suspend,
+ .resume = pegasus_resume,
+ .reset_resume = pegasus_reset_resume,
+ .id_table = pegasus_ids,
+ .supports_autosuspend = 1,
+};
+
+module_usb_driver(pegasus_driver);
+
+MODULE_AUTHOR("Martin Kepplinger <martink@posteo.de>");
+MODULE_DESCRIPTION("Pegasus Mobile Notetaker Pen tablet driver");
+MODULE_LICENSE("GPL");
config TOUCHSCREEN_MIGOR
tristate "Renesas MIGO-R touchscreen"
- depends on SH_MIGOR && I2C
+ depends on (SH_MIGOR || COMPILE_TEST) && I2C
help
Say Y here to enable MIGO-R touchscreen support.
To compile this driver as a module, choose M here: the
module will be called pcap_ts.
+config TOUCHSCREEN_RM_TS
+ tristate "Raydium I2C Touchscreen"
+ depends on I2C
+ depends on GPIOLIB || COMPILE_TEST
+ help
+ Say Y here if you have Raydium series I2C touchscreen,
+ such as RM32380, connected to your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called raydium_i2c_ts.
+
config TOUCHSCREEN_ST1232
tristate "Sitronix ST1232 touchscreen controllers"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called sur40.
+config TOUCHSCREEN_SURFACE3_SPI
+ tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
+ depends on SPI
+ depends on GPIOLIB || COMPILE_TEST
+ help
+ Say Y here if you have the Ntrig/Microsoft SPI touchscreen
+ controller chip as found on the Surface 3 in your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called surface3_spi.
+
config TOUCHSCREEN_SX8654
tristate "Semtech SX8654 touchscreen"
depends on I2C
obj-$(CONFIG_TOUCHSCREEN_PCAP) += pcap_ts.o
obj-$(CONFIG_TOUCHSCREEN_PENMOUNT) += penmount.o
obj-$(CONFIG_TOUCHSCREEN_PIXCIR) += pixcir_i2c_ts.o
+obj-$(CONFIG_TOUCHSCREEN_RM_TS) += raydium_i2c_ts.o
obj-$(CONFIG_TOUCHSCREEN_S3C2410) += s3c2410_ts.o
obj-$(CONFIG_TOUCHSCREEN_ST1232) += st1232.o
obj-$(CONFIG_TOUCHSCREEN_STMPE) += stmpe-ts.o
obj-$(CONFIG_TOUCHSCREEN_SUN4I) += sun4i-ts.o
obj-$(CONFIG_TOUCHSCREEN_SUR40) += sur40.o
+obj-$(CONFIG_TOUCHSCREEN_SURFACE3_SPI) += surface3_spi.o
obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC) += ti_am335x_tsc.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
} else {
input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, 0, 0);
input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
- touchscreen_parse_properties(input_dev, false);
+ touchscreen_parse_properties(input_dev, false, NULL);
if (!input_abs_get_max(input_dev, ABS_PRESSURE)) {
dev_err(dev, "Touchscreen pressure is not specified\n");
return ERR_PTR(-EINVAL);
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
#include <linux/module.h>
#include <linux/of.h>
struct i2c_client *client;
struct input_dev *input;
struct gpio_desc *wake_gpio;
- u32 max_x;
- u32 max_y;
- bool invert_x;
- bool invert_y;
- bool swap_x_y;
+ struct touchscreen_properties prop;
};
static int icn8318_read_touch_data(struct i2c_client *client,
struct icn8318_data *data = dev_id;
struct device *dev = &data->client->dev;
struct icn8318_touch_data touch_data;
- int i, ret, x, y;
+ int i, ret;
ret = icn8318_read_touch_data(data->client, &touch_data);
if (ret < 0) {
if (!act)
continue;
- x = be16_to_cpu(touch->x);
- y = be16_to_cpu(touch->y);
-
- if (data->invert_x)
- x = data->max_x - x;
-
- if (data->invert_y)
- y = data->max_y - y;
-
- if (!data->swap_x_y) {
- input_event(data->input, EV_ABS, ABS_MT_POSITION_X, x);
- input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, y);
- } else {
- input_event(data->input, EV_ABS, ABS_MT_POSITION_X, y);
- input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, x);
- }
+ touchscreen_report_pos(data->input, &data->prop,
+ be16_to_cpu(touch->x),
+ be16_to_cpu(touch->y), true);
}
input_mt_sync_frame(data->input);
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
- struct device_node *np = dev->of_node;
struct icn8318_data *data;
struct input_dev *input;
- u32 fuzz_x = 0, fuzz_y = 0;
int error;
if (!client->irq) {
return error;
}
- if (of_property_read_u32(np, "touchscreen-size-x", &data->max_x) ||
- of_property_read_u32(np, "touchscreen-size-y", &data->max_y)) {
- dev_err(dev, "Error touchscreen-size-x and/or -y missing\n");
- return -EINVAL;
- }
-
- /* Optional */
- of_property_read_u32(np, "touchscreen-fuzz-x", &fuzz_x);
- of_property_read_u32(np, "touchscreen-fuzz-y", &fuzz_y);
- data->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
- data->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
- data->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
-
input = devm_input_allocate_device(dev);
if (!input)
return -ENOMEM;
input->close = icn8318_stop;
input->dev.parent = dev;
- if (!data->swap_x_y) {
- input_set_abs_params(input, ABS_MT_POSITION_X, 0,
- data->max_x, fuzz_x, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
- data->max_y, fuzz_y, 0);
- } else {
- input_set_abs_params(input, ABS_MT_POSITION_X, 0,
- data->max_y, fuzz_y, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
- data->max_x, fuzz_x, 0);
+ input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
+ input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
+
+ touchscreen_parse_properties(input, true, &data->prop);
+ if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
+ !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
+ dev_err(dev, "Error touchscreen-size-x and/or -y missing\n");
+ return -EINVAL;
}
error = input_mt_init_slots(input, ICN8318_MAX_TOUCHES,
input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_X);
input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_Y);
- touchscreen_parse_properties(input_dev, true);
+ touchscreen_parse_properties(input_dev, true, NULL);
error = input_mt_init_slots(input_dev, CY_MAX_ID, 0);
if (error) {
struct edt_ft5x06_ts_data {
struct i2c_client *client;
struct input_dev *input;
+ struct touchscreen_properties prop;
u16 num_x;
u16 num_y;
if (!down)
continue;
- input_report_abs(tsdata->input, ABS_MT_POSITION_X, x);
- input_report_abs(tsdata->input, ABS_MT_POSITION_Y, y);
+ touchscreen_report_pos(tsdata->input, &tsdata->prop, x, y,
+ true);
}
input_mt_report_pointer_emulation(tsdata->input, true);
input_set_abs_params(input, ABS_MT_POSITION_Y,
0, tsdata->num_y * 64 - 1, 0, 0);
- touchscreen_parse_properties(input, true);
+ touchscreen_parse_properties(input, true, &tsdata->prop);
error = input_mt_init_slots(input, tsdata->max_support_points,
INPUT_MT_DIRECT);
return 0;
}
-static int migor_ts_suspend(struct device *dev)
+static int __maybe_unused migor_ts_suspend(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct migor_ts_priv *priv = i2c_get_clientdata(client);
return 0;
}
-static int migor_ts_resume(struct device *dev)
+static int __maybe_unused migor_ts_resume(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct migor_ts_priv *priv = i2c_get_clientdata(client);
{ "migor_ts", 0 },
{ }
};
-MODULE_DEVICE_TABLE(i2c, migor_ts);
+MODULE_DEVICE_TABLE(i2c, migor_ts_id);
static struct i2c_driver migor_ts_driver = {
.driver = {
* @input: input device that should be parsed
* @multitouch: specifies whether parsed properties should be applied to
* single-touch or multi-touch axes
+ * @prop: pointer to a struct touchscreen_properties into which to store
+ * axis swap and invert info for use with touchscreen_report_x_y();
+ * or %NULL
*
* This function parses common DT properties for touchscreens and setups the
* input device accordingly. The function keeps previously set up default
* values if no value is specified via DT.
*/
-void touchscreen_parse_properties(struct input_dev *input, bool multitouch)
+void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
+ struct touchscreen_properties *prop)
{
struct device *dev = input->dev.parent;
unsigned int axis;
&fuzz);
if (data_present)
touchscreen_set_params(input, axis, maximum, fuzz);
+
+ if (!prop)
+ return;
+
+ axis = multitouch ? ABS_MT_POSITION_X : ABS_X;
+
+ prop->max_x = input_abs_get_max(input, axis);
+ prop->max_y = input_abs_get_max(input, axis + 1);
+ prop->invert_x =
+ device_property_read_bool(dev, "touchscreen-inverted-x");
+ prop->invert_y =
+ device_property_read_bool(dev, "touchscreen-inverted-y");
+ prop->swap_x_y =
+ device_property_read_bool(dev, "touchscreen-swapped-x-y");
+
+ if (prop->swap_x_y)
+ swap(input->absinfo[axis], input->absinfo[axis + 1]);
}
EXPORT_SYMBOL(touchscreen_parse_properties);
+
+static void
+touchscreen_apply_prop_to_x_y(const struct touchscreen_properties *prop,
+ unsigned int *x, unsigned int *y)
+{
+ if (prop->invert_x)
+ *x = prop->max_x - *x;
+
+ if (prop->invert_y)
+ *y = prop->max_y - *y;
+
+ if (prop->swap_x_y)
+ swap(*x, *y);
+}
+
+/**
+ * touchscreen_set_mt_pos - Set input_mt_pos coordinates
+ * @pos: input_mt_pos to set coordinates of
+ * @prop: pointer to a struct touchscreen_properties
+ * @x: X coordinate to store in pos
+ * @y: Y coordinate to store in pos
+ *
+ * Adjust the passed in x and y values applying any axis inversion and
+ * swapping requested in the passed in touchscreen_properties and store
+ * the result in a struct input_mt_pos.
+ */
+void touchscreen_set_mt_pos(struct input_mt_pos *pos,
+ const struct touchscreen_properties *prop,
+ unsigned int x, unsigned int y)
+{
+ touchscreen_apply_prop_to_x_y(prop, &x, &y);
+ pos->x = x;
+ pos->y = y;
+}
+EXPORT_SYMBOL(touchscreen_set_mt_pos);
+
+/**
+ * touchscreen_report_pos - Report touchscreen coordinates
+ * @input: input_device to report coordinates for
+ * @prop: pointer to a struct touchscreen_properties
+ * @x: X coordinate to report
+ * @y: Y coordinate to report
+ * @multitouch: Report coordinates on single-touch or multi-touch axes
+ *
+ * Adjust the passed in x and y values applying any axis inversion and
+ * swapping requested in the passed in touchscreen_properties and then
+ * report the resulting coordinates on the input_dev's x and y axis.
+ */
+void touchscreen_report_pos(struct input_dev *input,
+ const struct touchscreen_properties *prop,
+ unsigned int x, unsigned int y,
+ bool multitouch)
+{
+ touchscreen_apply_prop_to_x_y(prop, &x, &y);
+ input_report_abs(input, multitouch ? ABS_MT_POSITION_X : ABS_X, x);
+ input_report_abs(input, multitouch ? ABS_MT_POSITION_Y : ABS_Y, y);
+}
+EXPORT_SYMBOL(touchscreen_report_pos);
#include <linux/input/touchscreen.h>
#include <linux/gpio.h>
#include <linux/gpio/consumer.h>
-/*#include <linux/of.h>*/
#include <linux/of_device.h>
#include <linux/platform_data/pixcir_i2c_ts.h>
+#include <asm/unaligned.h>
#define PIXCIR_MAX_SLOTS 5 /* Max fingers supported by driver */
struct gpio_desc *gpio_enable;
struct gpio_desc *gpio_wake;
const struct pixcir_i2c_chip_data *chip;
+ struct touchscreen_properties prop;
int max_fingers; /* Max fingers supported in this instance */
bool running;
};
-struct pixcir_touch {
- int x;
- int y;
- int id;
-};
-
struct pixcir_report_data {
int num_touches;
- struct pixcir_touch touches[PIXCIR_MAX_SLOTS];
+ struct input_mt_pos pos[PIXCIR_MAX_SLOTS];
+ int ids[PIXCIR_MAX_SLOTS];
};
static void pixcir_ts_parse(struct pixcir_i2c_ts_data *tsdata,
bufptr = &rdbuf[2];
for (i = 0; i < touch; i++) {
- report->touches[i].x = (bufptr[1] << 8) | bufptr[0];
- report->touches[i].y = (bufptr[3] << 8) | bufptr[2];
-
+ touchscreen_set_mt_pos(&report->pos[i], &tsdata->prop,
+ get_unaligned_le16(bufptr),
+ get_unaligned_le16(bufptr + 2));
if (chip->has_hw_ids) {
- report->touches[i].id = bufptr[4];
+ report->ids[i] = bufptr[4];
bufptr = bufptr + 5;
} else {
bufptr = bufptr + 4;
static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
struct pixcir_report_data *report)
{
- struct input_mt_pos pos[PIXCIR_MAX_SLOTS];
int slots[PIXCIR_MAX_SLOTS];
- struct pixcir_touch *touch;
int n, i, slot;
struct device *dev = &ts->client->dev;
const struct pixcir_i2c_chip_data *chip = ts->chip;
if (n > PIXCIR_MAX_SLOTS)
n = PIXCIR_MAX_SLOTS;
- if (!ts->chip->has_hw_ids) {
- for (i = 0; i < n; i++) {
- touch = &report->touches[i];
- pos[i].x = touch->x;
- pos[i].y = touch->y;
- }
-
- input_mt_assign_slots(ts->input, slots, pos, n, 0);
- }
+ if (!ts->chip->has_hw_ids)
+ input_mt_assign_slots(ts->input, slots, report->pos, n, 0);
for (i = 0; i < n; i++) {
- touch = &report->touches[i];
-
if (chip->has_hw_ids) {
- slot = input_mt_get_slot_by_key(ts->input, touch->id);
+ slot = input_mt_get_slot_by_key(ts->input,
+ report->ids[i]);
if (slot < 0) {
dev_dbg(dev, "no free slot for id 0x%x\n",
- touch->id);
+ report->ids[i]);
continue;
}
} else {
}
input_mt_slot(ts->input, slot);
- input_mt_report_slot_state(ts->input,
- MT_TOOL_FINGER, true);
+ input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, true);
- input_event(ts->input, EV_ABS, ABS_MT_POSITION_X, touch->x);
- input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y, touch->y);
+ input_report_abs(ts->input, ABS_MT_POSITION_X,
+ report->pos[i].x);
+ input_report_abs(ts->input, ABS_MT_POSITION_Y,
+ report->pos[i].y);
dev_dbg(dev, "%d: slot %d, x %d, y %d\n",
- i, slot, touch->x, touch->y);
+ i, slot, report->pos[i].x, report->pos[i].y);
}
input_mt_sync_frame(ts->input);
} else {
input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
- touchscreen_parse_properties(input, true);
+ touchscreen_parse_properties(input, true, &tsdata->prop);
if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
!input_abs_get_max(input, ABS_MT_POSITION_Y)) {
dev_err(dev, "Touchscreen size is not specified\n");
--- /dev/null
+/*
+ * Raydium touchscreen I2C driver.
+ *
+ * Copyright (C) 2012-2014, Raydium Semiconductor Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2, and only version 2, as published by the
+ * Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Raydium reserves the right to make changes without further notice
+ * to the materials described herein. Raydium does not assume any
+ * liability arising out of the application described herein.
+ *
+ * Contact Raydium Semiconductor Corporation at www.rad-ic.com
+ */
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <asm/unaligned.h>
+
+/* Slave I2C mode */
+#define RM_BOOT_BLDR 0x02
+#define RM_BOOT_MAIN 0x03
+
+/* I2C bootoloader commands */
+#define RM_CMD_BOOT_PAGE_WRT 0x0B /* send bl page write */
+#define RM_CMD_BOOT_WRT 0x11 /* send bl write */
+#define RM_CMD_BOOT_ACK 0x22 /* send ack*/
+#define RM_CMD_BOOT_CHK 0x33 /* send data check */
+#define RM_CMD_BOOT_READ 0x44 /* send wait bl data ready*/
+
+#define RM_BOOT_RDY 0xFF /* bl data ready */
+
+/* I2C main commands */
+#define RM_CMD_QUERY_BANK 0x2B
+#define RM_CMD_DATA_BANK 0x4D
+#define RM_CMD_ENTER_SLEEP 0x4E
+#define RM_CMD_BANK_SWITCH 0xAA
+
+#define RM_RESET_MSG_ADDR 0x40000004
+
+#define RM_MAX_READ_SIZE 56
+#define RM_PACKET_CRC_SIZE 2
+
+/* Touch relative info */
+#define RM_MAX_RETRIES 3
+#define RM_MAX_TOUCH_NUM 10
+#define RM_BOOT_DELAY_MS 100
+
+/* Offsets in contact data */
+#define RM_CONTACT_STATE_POS 0
+#define RM_CONTACT_X_POS 1
+#define RM_CONTACT_Y_POS 3
+#define RM_CONTACT_PRESSURE_POS 5
+#define RM_CONTACT_WIDTH_X_POS 6
+#define RM_CONTACT_WIDTH_Y_POS 7
+
+/* Bootloader relative info */
+#define RM_BL_WRT_CMD_SIZE 3 /* bl flash wrt cmd size */
+#define RM_BL_WRT_PKG_SIZE 32 /* bl wrt pkg size */
+#define RM_BL_WRT_LEN (RM_BL_WRT_PKG_SIZE + RM_BL_WRT_CMD_SIZE)
+#define RM_FW_PAGE_SIZE 128
+#define RM_MAX_FW_RETRIES 30
+#define RM_MAX_FW_SIZE 0xD000
+
+#define RM_POWERON_DELAY_USEC 500
+#define RM_RESET_DELAY_MSEC 50
+
+enum raydium_bl_cmd {
+ BL_HEADER = 0,
+ BL_PAGE_STR,
+ BL_PKG_IDX,
+ BL_DATA_STR,
+};
+
+enum raydium_bl_ack {
+ RAYDIUM_ACK_NULL = 0,
+ RAYDIUM_WAIT_READY,
+ RAYDIUM_PATH_READY,
+};
+
+enum raydium_boot_mode {
+ RAYDIUM_TS_MAIN = 0,
+ RAYDIUM_TS_BLDR,
+};
+
+/* Response to RM_CMD_DATA_BANK request */
+struct raydium_data_info {
+ __le32 data_bank_addr;
+ u8 pkg_size;
+ u8 tp_info_size;
+};
+
+struct raydium_info {
+ __le32 hw_ver; /*device version */
+ u8 main_ver;
+ u8 sub_ver;
+ __le16 ft_ver; /* test version */
+ u8 x_num;
+ u8 y_num;
+ __le16 x_max;
+ __le16 y_max;
+ u8 x_res; /* units/mm */
+ u8 y_res; /* units/mm */
+};
+
+/* struct raydium_data - represents state of Raydium touchscreen device */
+struct raydium_data {
+ struct i2c_client *client;
+ struct input_dev *input;
+
+ struct regulator *avdd;
+ struct regulator *vccio;
+ struct gpio_desc *reset_gpio;
+
+ struct raydium_info info;
+
+ struct mutex sysfs_mutex;
+
+ u8 *report_data;
+
+ u32 data_bank_addr;
+ u8 report_size;
+ u8 contact_size;
+ u8 pkg_size;
+
+ enum raydium_boot_mode boot_mode;
+
+ bool wake_irq_enabled;
+};
+
+static int raydium_i2c_send(struct i2c_client *client,
+ u8 addr, const void *data, size_t len)
+{
+ u8 *buf;
+ int tries = 0;
+ int ret;
+
+ buf = kmalloc(len + 1, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ buf[0] = addr;
+ memcpy(buf + 1, data, len);
+
+ do {
+ ret = i2c_master_send(client, buf, len + 1);
+ if (likely(ret == len + 1))
+ break;
+
+ msleep(20);
+ } while (++tries < RM_MAX_RETRIES);
+
+ kfree(buf);
+
+ if (unlikely(ret != len + 1)) {
+ if (ret >= 0)
+ ret = -EIO;
+ dev_err(&client->dev, "%s failed: %d\n", __func__, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int raydium_i2c_read(struct i2c_client *client,
+ u8 addr, void *data, size_t len)
+{
+ struct i2c_msg xfer[] = {
+ {
+ .addr = client->addr,
+ .len = 1,
+ .buf = &addr,
+ },
+ {
+ .addr = client->addr,
+ .flags = I2C_M_RD,
+ .len = len,
+ .buf = data,
+ }
+ };
+ int ret;
+
+ ret = i2c_transfer(client->adapter, xfer, ARRAY_SIZE(xfer));
+ if (unlikely(ret != ARRAY_SIZE(xfer)))
+ return ret < 0 ? ret : -EIO;
+
+ return 0;
+}
+
+static int raydium_i2c_read_message(struct i2c_client *client,
+ u32 addr, void *data, size_t len)
+{
+ __be32 be_addr;
+ size_t xfer_len;
+ int error;
+
+ while (len) {
+ xfer_len = min_t(size_t, len, RM_MAX_READ_SIZE);
+
+ be_addr = cpu_to_be32(addr);
+
+ error = raydium_i2c_send(client, RM_CMD_BANK_SWITCH,
+ &be_addr, sizeof(be_addr));
+ if (!error)
+ error = raydium_i2c_read(client, addr & 0xff,
+ data, xfer_len);
+ if (error)
+ return error;
+
+ len -= xfer_len;
+ data += xfer_len;
+ addr += xfer_len;
+ }
+
+ return 0;
+}
+
+static int raydium_i2c_send_message(struct i2c_client *client,
+ u32 addr, const void *data, size_t len)
+{
+ __be32 be_addr = cpu_to_be32(addr);
+ int error;
+
+ error = raydium_i2c_send(client, RM_CMD_BANK_SWITCH,
+ &be_addr, sizeof(be_addr));
+ if (!error)
+ error = raydium_i2c_send(client, addr & 0xff, data, len);
+
+ return error;
+}
+
+static int raydium_i2c_sw_reset(struct i2c_client *client)
+{
+ const u8 soft_rst_cmd = 0x01;
+ int error;
+
+ error = raydium_i2c_send_message(client, RM_RESET_MSG_ADDR,
+ &soft_rst_cmd, sizeof(soft_rst_cmd));
+ if (error) {
+ dev_err(&client->dev, "software reset failed: %d\n", error);
+ return error;
+ }
+
+ msleep(RM_RESET_DELAY_MSEC);
+
+ return 0;
+}
+
+static int raydium_i2c_query_ts_info(struct raydium_data *ts)
+{
+ struct i2c_client *client = ts->client;
+ struct raydium_data_info data_info;
+ __le32 query_bank_addr;
+
+ int error, retry_cnt;
+
+ for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
+ error = raydium_i2c_read(client, RM_CMD_DATA_BANK,
+ &data_info, sizeof(data_info));
+ if (error)
+ continue;
+
+ /*
+ * Warn user if we already allocated memory for reports and
+ * then the size changed (due to firmware update?) and keep
+ * old size instead.
+ */
+ if (ts->report_data && ts->pkg_size != data_info.pkg_size) {
+ dev_warn(&client->dev,
+ "report size changes, was: %d, new: %d\n",
+ ts->pkg_size, data_info.pkg_size);
+ } else {
+ ts->pkg_size = data_info.pkg_size;
+ ts->report_size = ts->pkg_size - RM_PACKET_CRC_SIZE;
+ }
+
+ ts->contact_size = data_info.tp_info_size;
+ ts->data_bank_addr = le32_to_cpu(data_info.data_bank_addr);
+
+ dev_dbg(&client->dev,
+ "data_bank_addr: %#08x, report_size: %d, contact_size: %d\n",
+ ts->data_bank_addr, ts->report_size, ts->contact_size);
+
+ error = raydium_i2c_read(client, RM_CMD_QUERY_BANK,
+ &query_bank_addr,
+ sizeof(query_bank_addr));
+ if (error)
+ continue;
+
+ error = raydium_i2c_read_message(client,
+ le32_to_cpu(query_bank_addr),
+ &ts->info, sizeof(ts->info));
+ if (error)
+ continue;
+
+ return 0;
+ }
+
+ dev_err(&client->dev, "failed to query device parameters: %d\n", error);
+ return error;
+}
+
+static int raydium_i2c_check_fw_status(struct raydium_data *ts)
+{
+ struct i2c_client *client = ts->client;
+ static const u8 bl_ack = 0x62;
+ static const u8 main_ack = 0x66;
+ u8 buf[4];
+ int error;
+
+ error = raydium_i2c_read(client, RM_CMD_BOOT_READ, buf, sizeof(buf));
+ if (!error) {
+ if (buf[0] == bl_ack)
+ ts->boot_mode = RAYDIUM_TS_BLDR;
+ else if (buf[0] == main_ack)
+ ts->boot_mode = RAYDIUM_TS_MAIN;
+ return 0;
+ }
+
+ return error;
+}
+
+static int raydium_i2c_initialize(struct raydium_data *ts)
+{
+ struct i2c_client *client = ts->client;
+ int error, retry_cnt;
+
+ for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
+ /* Wait for Hello packet */
+ msleep(RM_BOOT_DELAY_MS);
+
+ error = raydium_i2c_check_fw_status(ts);
+ if (error) {
+ dev_err(&client->dev,
+ "failed to read 'hello' packet: %d\n", error);
+ continue;
+ }
+
+ if (ts->boot_mode == RAYDIUM_TS_BLDR ||
+ ts->boot_mode == RAYDIUM_TS_MAIN) {
+ break;
+ }
+ }
+
+ if (error)
+ ts->boot_mode = RAYDIUM_TS_BLDR;
+
+ if (ts->boot_mode == RAYDIUM_TS_BLDR) {
+ ts->info.hw_ver = cpu_to_le32(0xffffffffUL);
+ ts->info.main_ver = 0xff;
+ ts->info.sub_ver = 0xff;
+ } else {
+ raydium_i2c_query_ts_info(ts);
+ }
+
+ return error;
+}
+
+static int raydium_i2c_bl_chk_state(struct i2c_client *client,
+ enum raydium_bl_ack state)
+{
+ static const u8 ack_ok[] = { 0xFF, 0x39, 0x30, 0x30, 0x54 };
+ u8 rbuf[sizeof(ack_ok)];
+ u8 retry;
+ int error;
+
+ for (retry = 0; retry < RM_MAX_FW_RETRIES; retry++) {
+ switch (state) {
+ case RAYDIUM_ACK_NULL:
+ return 0;
+
+ case RAYDIUM_WAIT_READY:
+ error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
+ &rbuf[0], 1);
+ if (!error && rbuf[0] == RM_BOOT_RDY)
+ return 0;
+
+ break;
+
+ case RAYDIUM_PATH_READY:
+ error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
+ rbuf, sizeof(rbuf));
+ if (!error && !memcmp(rbuf, ack_ok, sizeof(ack_ok)))
+ return 0;
+
+ break;
+
+ default:
+ dev_err(&client->dev, "%s: invalid target state %d\n",
+ __func__, state);
+ return -EINVAL;
+ }
+
+ msleep(20);
+ }
+
+ return -ETIMEDOUT;
+}
+
+static int raydium_i2c_write_object(struct i2c_client *client,
+ const void *data, size_t len,
+ enum raydium_bl_ack state)
+{
+ int error;
+
+ error = raydium_i2c_send(client, RM_CMD_BOOT_WRT, data, len);
+ if (error) {
+ dev_err(&client->dev, "WRT obj command failed: %d\n",
+ error);
+ return error;
+ }
+
+ error = raydium_i2c_send(client, RM_CMD_BOOT_ACK, NULL, 0);
+ if (error) {
+ dev_err(&client->dev, "Ack obj command failed: %d\n", error);
+ return error;
+ }
+
+ error = raydium_i2c_bl_chk_state(client, state);
+ if (error) {
+ dev_err(&client->dev, "BL check state failed: %d\n", error);
+ return error;
+ }
+ return 0;
+}
+
+static bool raydium_i2c_boot_trigger(struct i2c_client *client)
+{
+ static const u8 cmd[7][6] = {
+ { 0x08, 0x0C, 0x09, 0x00, 0x50, 0xD7 },
+ { 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
+ { 0x08, 0x04, 0x09, 0x00, 0x50, 0x00 },
+ { 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
+ { 0x08, 0x0C, 0x09, 0x00, 0x50, 0x00 },
+ { 0x06, 0x01, 0x00, 0x00, 0x00, 0x00 },
+ { 0x02, 0xA2, 0x00, 0x00, 0x00, 0x00 },
+ };
+ int i;
+ int error;
+
+ for (i = 0; i < 7; i++) {
+ error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
+ RAYDIUM_WAIT_READY);
+ if (error) {
+ dev_err(&client->dev,
+ "boot trigger failed at step %d: %d\n",
+ i, error);
+ return error;
+ }
+ }
+
+ return 0;
+}
+
+static bool raydium_i2c_fw_trigger(struct i2c_client *client)
+{
+ static const u8 cmd[5][11] = {
+ { 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0xD7, 0, 0, 0 },
+ { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
+ { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
+ { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
+ { 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
+ };
+ int i;
+ int error;
+
+ for (i = 0; i < 5; i++) {
+ error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
+ RAYDIUM_ACK_NULL);
+ if (error) {
+ dev_err(&client->dev,
+ "fw trigger failed at step %d: %d\n",
+ i, error);
+ return error;
+ }
+ }
+
+ return 0;
+}
+
+static int raydium_i2c_check_path(struct i2c_client *client)
+{
+ static const u8 cmd[] = { 0x09, 0x00, 0x09, 0x00, 0x50, 0x10, 0x00 };
+ int error;
+
+ error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
+ RAYDIUM_PATH_READY);
+ if (error) {
+ dev_err(&client->dev, "check path command failed: %d\n", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int raydium_i2c_enter_bl(struct i2c_client *client)
+{
+ static const u8 cal_cmd[] = { 0x00, 0x01, 0x52 };
+ int error;
+
+ error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
+ RAYDIUM_ACK_NULL);
+ if (error) {
+ dev_err(&client->dev, "enter bl command failed: %d\n", error);
+ return error;
+ }
+
+ msleep(RM_BOOT_DELAY_MS);
+ return 0;
+}
+
+static int raydium_i2c_leave_bl(struct i2c_client *client)
+{
+ static const u8 leave_cmd[] = { 0x05, 0x00 };
+ int error;
+
+ error = raydium_i2c_write_object(client, leave_cmd, sizeof(leave_cmd),
+ RAYDIUM_ACK_NULL);
+ if (error) {
+ dev_err(&client->dev, "leave bl command failed: %d\n", error);
+ return error;
+ }
+
+ msleep(RM_BOOT_DELAY_MS);
+ return 0;
+}
+
+static int raydium_i2c_write_checksum(struct i2c_client *client,
+ size_t length, u16 checksum)
+{
+ u8 checksum_cmd[] = { 0x00, 0x05, 0x6D, 0x00, 0x00, 0x00, 0x00 };
+ int error;
+
+ put_unaligned_le16(length, &checksum_cmd[3]);
+ put_unaligned_le16(checksum, &checksum_cmd[5]);
+
+ error = raydium_i2c_write_object(client,
+ checksum_cmd, sizeof(checksum_cmd),
+ RAYDIUM_ACK_NULL);
+ if (error) {
+ dev_err(&client->dev, "failed to write checksum: %d\n",
+ error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int raydium_i2c_disable_watch_dog(struct i2c_client *client)
+{
+ static const u8 cmd[] = { 0x0A, 0xAA };
+ int error;
+
+ error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
+ RAYDIUM_WAIT_READY);
+ if (error) {
+ dev_err(&client->dev, "disable watchdog command failed: %d\n",
+ error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int raydium_i2c_fw_write_page(struct i2c_client *client,
+ u16 page_idx, const void *data, size_t len)
+{
+ u8 buf[RM_BL_WRT_LEN];
+ size_t xfer_len;
+ int error;
+ int i;
+
+ BUILD_BUG_ON((RM_FW_PAGE_SIZE % RM_BL_WRT_PKG_SIZE) != 0);
+
+ for (i = 0; i < RM_FW_PAGE_SIZE / RM_BL_WRT_PKG_SIZE; i++) {
+ buf[BL_HEADER] = RM_CMD_BOOT_PAGE_WRT;
+ buf[BL_PAGE_STR] = page_idx ? 0xff : 0;
+ buf[BL_PKG_IDX] = i + 1;
+
+ xfer_len = min_t(size_t, len, RM_BL_WRT_PKG_SIZE);
+ memcpy(&buf[BL_DATA_STR], data, xfer_len);
+ if (len < RM_BL_WRT_PKG_SIZE)
+ memset(&buf[BL_DATA_STR + xfer_len], 0xff,
+ RM_BL_WRT_PKG_SIZE - xfer_len);
+
+ error = raydium_i2c_write_object(client, buf, RM_BL_WRT_LEN,
+ RAYDIUM_WAIT_READY);
+ if (error) {
+ dev_err(&client->dev,
+ "page write command failed for page %d, chunk %d: %d\n",
+ page_idx, i, error);
+ return error;
+ }
+
+ data += xfer_len;
+ len -= xfer_len;
+ }
+
+ return error;
+}
+
+static u16 raydium_calc_chksum(const u8 *buf, u16 len)
+{
+ u16 checksum = 0;
+ u16 i;
+
+ for (i = 0; i < len; i++)
+ checksum += buf[i];
+
+ return checksum;
+}
+
+static int raydium_i2c_do_update_firmware(struct raydium_data *ts,
+ const struct firmware *fw)
+{
+ struct i2c_client *client = ts->client;
+ const void *data;
+ size_t data_len;
+ size_t len;
+ int page_nr;
+ int i;
+ int error;
+ u16 fw_checksum;
+
+ if (fw->size == 0 || fw->size > RM_MAX_FW_SIZE) {
+ dev_err(&client->dev, "Invalid firmware length\n");
+ return -EINVAL;
+ }
+
+ error = raydium_i2c_check_fw_status(ts);
+ if (error) {
+ dev_err(&client->dev, "Unable to access IC %d\n", error);
+ return error;
+ }
+
+ if (ts->boot_mode == RAYDIUM_TS_MAIN) {
+ for (i = 0; i < RM_MAX_RETRIES; i++) {
+ error = raydium_i2c_enter_bl(client);
+ if (!error) {
+ error = raydium_i2c_check_fw_status(ts);
+ if (error) {
+ dev_err(&client->dev,
+ "unable to access IC: %d\n",
+ error);
+ return error;
+ }
+
+ if (ts->boot_mode == RAYDIUM_TS_BLDR)
+ break;
+ }
+ }
+
+ if (ts->boot_mode == RAYDIUM_TS_MAIN) {
+ dev_err(&client->dev,
+ "failied to jump to boot loader: %d\n",
+ error);
+ return -EIO;
+ }
+ }
+
+ error = raydium_i2c_disable_watch_dog(client);
+ if (error)
+ return error;
+
+ error = raydium_i2c_check_path(client);
+ if (error)
+ return error;
+
+ error = raydium_i2c_boot_trigger(client);
+ if (error) {
+ dev_err(&client->dev, "send boot trigger fail: %d\n", error);
+ return error;
+ }
+
+ msleep(RM_BOOT_DELAY_MS);
+
+ data = fw->data;
+ data_len = fw->size;
+ page_nr = 0;
+
+ while (data_len) {
+ len = min_t(size_t, data_len, RM_FW_PAGE_SIZE);
+
+ error = raydium_i2c_fw_write_page(client, page_nr++, data, len);
+ if (error)
+ return error;
+
+ msleep(20);
+
+ data += len;
+ data_len -= len;
+ }
+
+ error = raydium_i2c_leave_bl(client);
+ if (error) {
+ dev_err(&client->dev,
+ "failed to leave boot loader: %d\n", error);
+ return error;
+ }
+
+ dev_dbg(&client->dev, "left boot loader mode\n");
+ msleep(RM_BOOT_DELAY_MS);
+
+ error = raydium_i2c_check_fw_status(ts);
+ if (error) {
+ dev_err(&client->dev,
+ "failed to check fw status after write: %d\n",
+ error);
+ return error;
+ }
+
+ if (ts->boot_mode != RAYDIUM_TS_MAIN) {
+ dev_err(&client->dev,
+ "failed to switch to main fw after writing firmware: %d\n",
+ error);
+ return -EINVAL;
+ }
+
+ error = raydium_i2c_fw_trigger(client);
+ if (error) {
+ dev_err(&client->dev, "failed to trigger fw: %d\n", error);
+ return error;
+ }
+
+ fw_checksum = raydium_calc_chksum(fw->data, fw->size);
+
+ error = raydium_i2c_write_checksum(client, fw->size, fw_checksum);
+ if (error)
+ return error;
+
+ return 0;
+}
+
+static int raydium_i2c_fw_update(struct raydium_data *ts)
+{
+ struct i2c_client *client = ts->client;
+ const struct firmware *fw = NULL;
+ const char *fw_file = "raydium.fw";
+ int error;
+
+ error = request_firmware(&fw, fw_file, &client->dev);
+ if (error) {
+ dev_err(&client->dev, "Unable to open firmware %s\n", fw_file);
+ return error;
+ }
+
+ disable_irq(client->irq);
+
+ error = raydium_i2c_do_update_firmware(ts, fw);
+ if (error) {
+ dev_err(&client->dev, "firmware update failed: %d\n", error);
+ ts->boot_mode = RAYDIUM_TS_BLDR;
+ goto out_enable_irq;
+ }
+
+ error = raydium_i2c_initialize(ts);
+ if (error) {
+ dev_err(&client->dev,
+ "failed to initialize device after firmware update: %d\n",
+ error);
+ ts->boot_mode = RAYDIUM_TS_BLDR;
+ goto out_enable_irq;
+ }
+
+ ts->boot_mode = RAYDIUM_TS_MAIN;
+
+out_enable_irq:
+ enable_irq(client->irq);
+ msleep(100);
+
+ release_firmware(fw);
+
+ return error;
+}
+
+static void raydium_mt_event(struct raydium_data *ts)
+{
+ int i;
+
+ for (i = 0; i < ts->report_size / ts->contact_size; i++) {
+ u8 *contact = &ts->report_data[ts->contact_size * i];
+ bool state = contact[RM_CONTACT_STATE_POS];
+ u8 wx, wy;
+
+ input_mt_slot(ts->input, i);
+ input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, state);
+
+ if (!state)
+ continue;
+
+ input_report_abs(ts->input, ABS_MT_POSITION_X,
+ get_unaligned_le16(&contact[RM_CONTACT_X_POS]));
+ input_report_abs(ts->input, ABS_MT_POSITION_Y,
+ get_unaligned_le16(&contact[RM_CONTACT_Y_POS]));
+ input_report_abs(ts->input, ABS_MT_PRESSURE,
+ contact[RM_CONTACT_PRESSURE_POS]);
+
+ wx = contact[RM_CONTACT_WIDTH_X_POS];
+ wy = contact[RM_CONTACT_WIDTH_Y_POS];
+
+ input_report_abs(ts->input, ABS_MT_TOUCH_MAJOR, max(wx, wy));
+ input_report_abs(ts->input, ABS_MT_TOUCH_MINOR, min(wx, wy));
+ }
+
+ input_mt_sync_frame(ts->input);
+ input_sync(ts->input);
+}
+
+static irqreturn_t raydium_i2c_irq(int irq, void *_dev)
+{
+ struct raydium_data *ts = _dev;
+ int error;
+ u16 fw_crc;
+ u16 calc_crc;
+
+ if (ts->boot_mode != RAYDIUM_TS_MAIN)
+ goto out;
+
+ error = raydium_i2c_read_message(ts->client, ts->data_bank_addr,
+ ts->report_data, ts->pkg_size);
+ if (error)
+ goto out;
+
+ fw_crc = get_unaligned_le16(&ts->report_data[ts->report_size]);
+ calc_crc = raydium_calc_chksum(ts->report_data, ts->report_size);
+ if (unlikely(fw_crc != calc_crc)) {
+ dev_warn(&ts->client->dev,
+ "%s: invalid packet crc %#04x vs %#04x\n",
+ __func__, calc_crc, fw_crc);
+ goto out;
+ }
+
+ raydium_mt_event(ts);
+
+out:
+ return IRQ_HANDLED;
+}
+
+static ssize_t raydium_i2c_fw_ver_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct raydium_data *ts = i2c_get_clientdata(client);
+
+ return sprintf(buf, "%d.%d\n", ts->info.main_ver, ts->info.sub_ver);
+}
+
+static ssize_t raydium_i2c_hw_ver_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct raydium_data *ts = i2c_get_clientdata(client);
+
+ return sprintf(buf, "%#04x\n", le32_to_cpu(ts->info.hw_ver));
+}
+
+static ssize_t raydium_i2c_boot_mode_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct raydium_data *ts = i2c_get_clientdata(client);
+
+ return sprintf(buf, "%s\n",
+ ts->boot_mode == RAYDIUM_TS_MAIN ?
+ "Normal" : "Recovery");
+}
+
+static ssize_t raydium_i2c_update_fw_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct raydium_data *ts = i2c_get_clientdata(client);
+ int error;
+
+ error = mutex_lock_interruptible(&ts->sysfs_mutex);
+ if (error)
+ return error;
+
+ error = raydium_i2c_fw_update(ts);
+
+ mutex_unlock(&ts->sysfs_mutex);
+
+ return error ?: count;
+}
+
+static ssize_t raydium_i2c_calibrate_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct raydium_data *ts = i2c_get_clientdata(client);
+ static const u8 cal_cmd[] = { 0x00, 0x01, 0x9E };
+ int error;
+
+ error = mutex_lock_interruptible(&ts->sysfs_mutex);
+ if (error)
+ return error;
+
+ error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
+ RAYDIUM_WAIT_READY);
+ if (error)
+ dev_err(&client->dev, "calibrate command failed: %d\n", error);
+
+ mutex_unlock(&ts->sysfs_mutex);
+ return error ?: count;
+}
+
+static DEVICE_ATTR(fw_version, S_IRUGO, raydium_i2c_fw_ver_show, NULL);
+static DEVICE_ATTR(hw_version, S_IRUGO, raydium_i2c_hw_ver_show, NULL);
+static DEVICE_ATTR(boot_mode, S_IRUGO, raydium_i2c_boot_mode_show, NULL);
+static DEVICE_ATTR(update_fw, S_IWUSR, NULL, raydium_i2c_update_fw_store);
+static DEVICE_ATTR(calibrate, S_IWUSR, NULL, raydium_i2c_calibrate_store);
+
+static struct attribute *raydium_i2c_attributes[] = {
+ &dev_attr_update_fw.attr,
+ &dev_attr_boot_mode.attr,
+ &dev_attr_fw_version.attr,
+ &dev_attr_hw_version.attr,
+ &dev_attr_calibrate.attr,
+ NULL
+};
+
+static struct attribute_group raydium_i2c_attribute_group = {
+ .attrs = raydium_i2c_attributes,
+};
+
+static void raydium_i2c_remove_sysfs_group(void *_data)
+{
+ struct raydium_data *ts = _data;
+
+ sysfs_remove_group(&ts->client->dev.kobj, &raydium_i2c_attribute_group);
+}
+
+static int raydium_i2c_power_on(struct raydium_data *ts)
+{
+ int error;
+
+ if (!ts->reset_gpio)
+ return 0;
+
+ gpiod_set_value_cansleep(ts->reset_gpio, 1);
+
+ error = regulator_enable(ts->avdd);
+ if (error) {
+ dev_err(&ts->client->dev,
+ "failed to enable avdd regulator: %d\n", error);
+ goto release_reset_gpio;
+ }
+
+ error = regulator_enable(ts->vccio);
+ if (error) {
+ regulator_disable(ts->avdd);
+ dev_err(&ts->client->dev,
+ "failed to enable vccio regulator: %d\n", error);
+ goto release_reset_gpio;
+ }
+
+ udelay(RM_POWERON_DELAY_USEC);
+
+release_reset_gpio:
+ gpiod_set_value_cansleep(ts->reset_gpio, 0);
+
+ if (error)
+ return error;
+
+ msleep(RM_RESET_DELAY_MSEC);
+
+ return 0;
+}
+
+static void raydium_i2c_power_off(void *_data)
+{
+ struct raydium_data *ts = _data;
+
+ if (ts->reset_gpio) {
+ gpiod_set_value_cansleep(ts->reset_gpio, 1);
+ regulator_disable(ts->vccio);
+ regulator_disable(ts->avdd);
+ }
+}
+
+static int raydium_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ union i2c_smbus_data dummy;
+ struct raydium_data *ts;
+ int error;
+
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+ dev_err(&client->dev,
+ "i2c check functionality error (need I2C_FUNC_I2C)\n");
+ return -ENXIO;
+ }
+
+ ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL);
+ if (!ts)
+ return -ENOMEM;
+
+ mutex_init(&ts->sysfs_mutex);
+
+ ts->client = client;
+ i2c_set_clientdata(client, ts);
+
+ ts->avdd = devm_regulator_get(&client->dev, "avdd");
+ if (IS_ERR(ts->avdd)) {
+ error = PTR_ERR(ts->avdd);
+ if (error != -EPROBE_DEFER)
+ dev_err(&client->dev,
+ "Failed to get 'avdd' regulator: %d\n", error);
+ return error;
+ }
+
+ ts->vccio = devm_regulator_get(&client->dev, "vccio");
+ if (IS_ERR(ts->vccio)) {
+ error = PTR_ERR(ts->vccio);
+ if (error != -EPROBE_DEFER)
+ dev_err(&client->dev,
+ "Failed to get 'vccio' regulator: %d\n", error);
+ return error;
+ }
+
+ ts->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(ts->reset_gpio)) {
+ error = PTR_ERR(ts->reset_gpio);
+ if (error != -EPROBE_DEFER)
+ dev_err(&client->dev,
+ "failed to get reset gpio: %d\n", error);
+ return error;
+ }
+
+ error = raydium_i2c_power_on(ts);
+ if (error)
+ return error;
+
+ error = devm_add_action(&client->dev, raydium_i2c_power_off, ts);
+ if (error) {
+ dev_err(&client->dev,
+ "failed to install power off action: %d\n", error);
+ raydium_i2c_power_off(ts);
+ return error;
+ }
+
+ /* Make sure there is something at this address */
+ if (i2c_smbus_xfer(client->adapter, client->addr, 0,
+ I2C_SMBUS_READ, 0, I2C_SMBUS_BYTE, &dummy) < 0) {
+ dev_err(&client->dev, "nothing at this address\n");
+ return -ENXIO;
+ }
+
+ error = raydium_i2c_initialize(ts);
+ if (error) {
+ dev_err(&client->dev, "failed to initialize: %d\n", error);
+ return error;
+ }
+
+ ts->report_data = devm_kmalloc(&client->dev,
+ ts->pkg_size, GFP_KERNEL);
+ if (!ts->report_data)
+ return -ENOMEM;
+
+ ts->input = devm_input_allocate_device(&client->dev);
+ if (!ts->input) {
+ dev_err(&client->dev, "Failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ ts->input->name = "Raydium Touchscreen";
+ ts->input->id.bustype = BUS_I2C;
+
+ input_set_drvdata(ts->input, ts);
+
+ input_set_abs_params(ts->input, ABS_MT_POSITION_X,
+ 0, le16_to_cpu(ts->info.x_max), 0, 0);
+ input_set_abs_params(ts->input, ABS_MT_POSITION_Y,
+ 0, le16_to_cpu(ts->info.y_max), 0, 0);
+ input_abs_set_res(ts->input, ABS_MT_POSITION_X, ts->info.x_res);
+ input_abs_set_res(ts->input, ABS_MT_POSITION_Y, ts->info.y_res);
+
+ input_set_abs_params(ts->input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
+ input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
+
+ error = input_mt_init_slots(ts->input, RM_MAX_TOUCH_NUM,
+ INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
+ if (error) {
+ dev_err(&client->dev,
+ "failed to initialize MT slots: %d\n", error);
+ return error;
+ }
+
+ error = input_register_device(ts->input);
+ if (error) {
+ dev_err(&client->dev,
+ "unable to register input device: %d\n", error);
+ return error;
+ }
+
+ error = devm_request_threaded_irq(&client->dev, client->irq,
+ NULL, raydium_i2c_irq,
+ IRQF_ONESHOT, client->name, ts);
+ if (error) {
+ dev_err(&client->dev, "Failed to register interrupt\n");
+ return error;
+ }
+
+ error = sysfs_create_group(&client->dev.kobj,
+ &raydium_i2c_attribute_group);
+ if (error) {
+ dev_err(&client->dev, "failed to create sysfs attributes: %d\n",
+ error);
+ return error;
+ }
+
+ error = devm_add_action(&client->dev,
+ raydium_i2c_remove_sysfs_group, ts);
+ if (error) {
+ raydium_i2c_remove_sysfs_group(ts);
+ dev_err(&client->dev,
+ "Failed to add sysfs cleanup action: %d\n", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static void __maybe_unused raydium_enter_sleep(struct i2c_client *client)
+{
+ static const u8 sleep_cmd[] = { 0x5A, 0xff, 0x00, 0x0f };
+ int error;
+
+ error = raydium_i2c_send(client, RM_CMD_ENTER_SLEEP,
+ sleep_cmd, sizeof(sleep_cmd));
+ if (error)
+ dev_err(&client->dev,
+ "sleep command failed: %d\n", error);
+}
+
+static int __maybe_unused raydium_i2c_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct raydium_data *ts = i2c_get_clientdata(client);
+
+ /* Sleep is not available in BLDR recovery mode */
+ if (ts->boot_mode != RAYDIUM_TS_MAIN)
+ return -EBUSY;
+
+ disable_irq(client->irq);
+
+ if (device_may_wakeup(dev)) {
+ raydium_enter_sleep(client);
+
+ ts->wake_irq_enabled = (enable_irq_wake(client->irq) == 0);
+ } else {
+ raydium_i2c_power_off(ts);
+ }
+
+ return 0;
+}
+
+static int __maybe_unused raydium_i2c_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct raydium_data *ts = i2c_get_clientdata(client);
+
+ if (device_may_wakeup(dev)) {
+ if (ts->wake_irq_enabled)
+ disable_irq_wake(client->irq);
+ raydium_i2c_sw_reset(client);
+ } else {
+ raydium_i2c_power_on(ts);
+ raydium_i2c_initialize(ts);
+ }
+
+ enable_irq(client->irq);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(raydium_i2c_pm_ops,
+ raydium_i2c_suspend, raydium_i2c_resume);
+
+static const struct i2c_device_id raydium_i2c_id[] = {
+ { "raydium_i2c" , 0 },
+ { "rm32380", 0 },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, raydium_i2c_id);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id raydium_acpi_id[] = {
+ { "RAYD0001", 0 },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(acpi, raydium_acpi_id);
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id raydium_of_match[] = {
+ { .compatible = "raydium,rm32380", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, raydium_of_match);
+#endif
+
+static struct i2c_driver raydium_i2c_driver = {
+ .probe = raydium_i2c_probe,
+ .id_table = raydium_i2c_id,
+ .driver = {
+ .name = "raydium_ts",
+ .pm = &raydium_i2c_pm_ops,
+ .acpi_match_table = ACPI_PTR(raydium_acpi_id),
+ .of_match_table = of_match_ptr(raydium_of_match),
+ },
+};
+module_i2c_driver(raydium_i2c_driver);
+
+MODULE_AUTHOR("Raydium");
+MODULE_DESCRIPTION("Raydium I2c Touchscreen driver");
+MODULE_LICENSE("GPL v2");
--- /dev/null
+/*
+ * Driver for Ntrig/Microsoft Touchscreens over SPI
+ *
+ * Copyright (c) 2016 Red Hat Inc.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; version 2 of the License.
+ */
+
+#include <linux/kernel.h>
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/acpi.h>
+
+#include <asm/unaligned.h>
+
+#define SURFACE3_PACKET_SIZE 264
+
+#define SURFACE3_REPORT_TOUCH 0xd2
+#define SURFACE3_REPORT_PEN 0x16
+
+struct surface3_ts_data {
+ struct spi_device *spi;
+ struct gpio_desc *gpiod_rst[2];
+ struct input_dev *input_dev;
+ struct input_dev *pen_input_dev;
+ int pen_tool;
+
+ u8 rd_buf[SURFACE3_PACKET_SIZE] ____cacheline_aligned;
+};
+
+struct surface3_ts_data_finger {
+ u8 status;
+ __le16 tracking_id;
+ __le16 x;
+ __le16 cx;
+ __le16 y;
+ __le16 cy;
+ __le16 width;
+ __le16 height;
+ u32 padding;
+} __packed;
+
+struct surface3_ts_data_pen {
+ u8 status;
+ __le16 x;
+ __le16 y;
+ __le16 pressure;
+ u8 padding;
+} __packed;
+
+static int surface3_spi_read(struct surface3_ts_data *ts_data)
+{
+ struct spi_device *spi = ts_data->spi;
+
+ memset(ts_data->rd_buf, 0, sizeof(ts_data->rd_buf));
+ return spi_read(spi, ts_data->rd_buf, sizeof(ts_data->rd_buf));
+}
+
+static void surface3_spi_report_touch(struct surface3_ts_data *ts_data,
+ struct surface3_ts_data_finger *finger)
+{
+ int st = finger->status & 0x01;
+ int slot;
+
+ slot = input_mt_get_slot_by_key(ts_data->input_dev,
+ get_unaligned_le16(&finger->tracking_id));
+ if (slot < 0)
+ return;
+
+ input_mt_slot(ts_data->input_dev, slot);
+ input_mt_report_slot_state(ts_data->input_dev, MT_TOOL_FINGER, st);
+ if (st) {
+ input_report_abs(ts_data->input_dev,
+ ABS_MT_POSITION_X,
+ get_unaligned_le16(&finger->x));
+ input_report_abs(ts_data->input_dev,
+ ABS_MT_POSITION_Y,
+ get_unaligned_le16(&finger->y));
+ input_report_abs(ts_data->input_dev,
+ ABS_MT_WIDTH_MAJOR,
+ get_unaligned_le16(&finger->width));
+ input_report_abs(ts_data->input_dev,
+ ABS_MT_WIDTH_MINOR,
+ get_unaligned_le16(&finger->height));
+ }
+}
+
+static void surface3_spi_process_touch(struct surface3_ts_data *ts_data, u8 *data)
+{
+ u16 timestamp;
+ unsigned int i;
+ timestamp = get_unaligned_le16(&data[15]);
+
+ for (i = 0; i < 13; i++) {
+ struct surface3_ts_data_finger *finger;
+
+ finger = (struct surface3_ts_data_finger *)&data[17 +
+ i * sizeof(struct surface3_ts_data_finger)];
+
+ /*
+ * When bit 5 of status is 1, it marks the end of the report:
+ * - touch present: 0xe7
+ * - touch released: 0xe4
+ * - nothing valuable: 0xff
+ */
+ if (finger->status & 0x10)
+ break;
+
+ surface3_spi_report_touch(ts_data, finger);
+ }
+
+ input_mt_sync_frame(ts_data->input_dev);
+ input_sync(ts_data->input_dev);
+}
+
+static void surface3_spi_report_pen(struct surface3_ts_data *ts_data,
+ struct surface3_ts_data_pen *pen)
+{
+ struct input_dev *dev = ts_data->pen_input_dev;
+ int st = pen->status;
+ int prox = st & 0x01;
+ int rubber = st & 0x18;
+ int tool = (prox && rubber) ? BTN_TOOL_RUBBER : BTN_TOOL_PEN;
+
+ /* fake proximity out to switch tools */
+ if (ts_data->pen_tool != tool) {
+ input_report_key(dev, ts_data->pen_tool, 0);
+ input_sync(dev);
+ ts_data->pen_tool = tool;
+ }
+
+ input_report_key(dev, BTN_TOUCH, st & 0x12);
+
+ input_report_key(dev, ts_data->pen_tool, prox);
+
+ if (st) {
+ input_report_key(dev,
+ BTN_STYLUS,
+ st & 0x04);
+
+ input_report_abs(dev,
+ ABS_X,
+ get_unaligned_le16(&pen->x));
+ input_report_abs(dev,
+ ABS_Y,
+ get_unaligned_le16(&pen->y));
+ input_report_abs(dev,
+ ABS_PRESSURE,
+ get_unaligned_le16(&pen->pressure));
+ }
+}
+
+static void surface3_spi_process_pen(struct surface3_ts_data *ts_data, u8 *data)
+{
+ struct surface3_ts_data_pen *pen;
+
+ pen = (struct surface3_ts_data_pen *)&data[15];
+
+ surface3_spi_report_pen(ts_data, pen);
+ input_sync(ts_data->pen_input_dev);
+}
+
+static void surface3_spi_process(struct surface3_ts_data *ts_data)
+{
+ const char header[] = {
+ 0xff, 0xff, 0xff, 0xff, 0xa5, 0x5a, 0xe7, 0x7e, 0x01
+ };
+ u8 *data = ts_data->rd_buf;
+
+ if (memcmp(header, data, sizeof(header)))
+ dev_err(&ts_data->spi->dev,
+ "%s header error: %*ph, ignoring...\n",
+ __func__, (int)sizeof(header), data);
+
+ switch (data[9]) {
+ case SURFACE3_REPORT_TOUCH:
+ surface3_spi_process_touch(ts_data, data);
+ break;
+ case SURFACE3_REPORT_PEN:
+ surface3_spi_process_pen(ts_data, data);
+ break;
+ default:
+ dev_err(&ts_data->spi->dev,
+ "%s unknown packet type: %x, ignoring...\n",
+ __func__, data[9]);
+ break;
+ }
+}
+
+static irqreturn_t surface3_spi_irq_handler(int irq, void *dev_id)
+{
+ struct surface3_ts_data *data = dev_id;
+
+ if (surface3_spi_read(data))
+ return IRQ_HANDLED;
+
+ dev_dbg(&data->spi->dev, "%s received -> %*ph\n",
+ __func__, SURFACE3_PACKET_SIZE, data->rd_buf);
+ surface3_spi_process(data);
+
+ return IRQ_HANDLED;
+}
+
+static void surface3_spi_power(struct surface3_ts_data *data, bool on)
+{
+ gpiod_set_value(data->gpiod_rst[0], on);
+ gpiod_set_value(data->gpiod_rst[1], on);
+ /* let the device settle a little */
+ msleep(20);
+}
+
+/**
+ * surface3_spi_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: surface3_spi_ts_data pointer
+ */
+static int surface3_spi_get_gpio_config(struct surface3_ts_data *data)
+{
+ int error;
+ struct device *dev;
+ struct gpio_desc *gpiod;
+ int i;
+
+ dev = &data->spi->dev;
+
+ /* Get the reset lines GPIO pin number */
+ for (i = 0; i < 2; i++) {
+ gpiod = devm_gpiod_get_index(dev, NULL, i, GPIOD_OUT_LOW);
+ if (IS_ERR(gpiod)) {
+ error = PTR_ERR(gpiod);
+ if (error != -EPROBE_DEFER)
+ dev_err(dev,
+ "Failed to get power GPIO %d: %d\n",
+ i,
+ error);
+ return error;
+ }
+
+ data->gpiod_rst[i] = gpiod;
+ }
+
+ return 0;
+}
+
+static int surface3_spi_create_touch_input(struct surface3_ts_data *data)
+{
+ struct input_dev *input;
+ int error;
+
+ input = devm_input_allocate_device(&data->spi->dev);
+ if (!input)
+ return -ENOMEM;
+
+ data->input_dev = input;
+
+ input_set_abs_params(input, ABS_MT_POSITION_X, 0, 9600, 0, 0);
+ input_abs_set_res(input, ABS_MT_POSITION_X, 40);
+ input_set_abs_params(input, ABS_MT_POSITION_Y, 0, 7200, 0, 0);
+ input_abs_set_res(input, ABS_MT_POSITION_Y, 48);
+ input_set_abs_params(input, ABS_MT_WIDTH_MAJOR, 0, 1024, 0, 0);
+ input_set_abs_params(input, ABS_MT_WIDTH_MINOR, 0, 1024, 0, 0);
+ input_mt_init_slots(input, 10, INPUT_MT_DIRECT);
+
+ input->name = "Surface3 SPI Capacitive TouchScreen";
+ input->phys = "input/ts";
+ input->id.bustype = BUS_SPI;
+ input->id.vendor = 0x045e; /* Microsoft */
+ input->id.product = 0x0001;
+ input->id.version = 0x0000;
+
+ error = input_register_device(input);
+ if (error) {
+ dev_err(&data->spi->dev,
+ "Failed to register input device: %d", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int surface3_spi_create_pen_input(struct surface3_ts_data *data)
+{
+ struct input_dev *input;
+ int error;
+
+ input = devm_input_allocate_device(&data->spi->dev);
+ if (!input)
+ return -ENOMEM;
+
+ data->pen_input_dev = input;
+ data->pen_tool = BTN_TOOL_PEN;
+
+ __set_bit(INPUT_PROP_DIRECT, input->propbit);
+ __set_bit(INPUT_PROP_POINTER, input->propbit);
+ input_set_abs_params(input, ABS_X, 0, 9600, 0, 0);
+ input_abs_set_res(input, ABS_X, 40);
+ input_set_abs_params(input, ABS_Y, 0, 7200, 0, 0);
+ input_abs_set_res(input, ABS_Y, 48);
+ input_set_abs_params(input, ABS_PRESSURE, 0, 1024, 0, 0);
+ input_set_capability(input, EV_KEY, BTN_TOUCH);
+ input_set_capability(input, EV_KEY, BTN_STYLUS);
+ input_set_capability(input, EV_KEY, BTN_TOOL_PEN);
+ input_set_capability(input, EV_KEY, BTN_TOOL_RUBBER);
+
+ input->name = "Surface3 SPI Pen Input";
+ input->phys = "input/ts";
+ input->id.bustype = BUS_SPI;
+ input->id.vendor = 0x045e; /* Microsoft */
+ input->id.product = 0x0002;
+ input->id.version = 0x0000;
+
+ error = input_register_device(input);
+ if (error) {
+ dev_err(&data->spi->dev,
+ "Failed to register input device: %d", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int surface3_spi_probe(struct spi_device *spi)
+{
+ struct surface3_ts_data *data;
+ int error;
+
+ /* Set up SPI*/
+ spi->bits_per_word = 8;
+ spi->mode = SPI_MODE_0;
+ error = spi_setup(spi);
+ if (error)
+ return error;
+
+ data = devm_kzalloc(&spi->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->spi = spi;
+ spi_set_drvdata(spi, data);
+
+ error = surface3_spi_get_gpio_config(data);
+ if (error)
+ return error;
+
+ surface3_spi_power(data, true);
+ surface3_spi_power(data, false);
+ surface3_spi_power(data, true);
+
+ error = surface3_spi_create_touch_input(data);
+ if (error)
+ return error;
+
+ error = surface3_spi_create_pen_input(data);
+ if (error)
+ return error;
+
+ error = devm_request_threaded_irq(&spi->dev, spi->irq,
+ NULL, surface3_spi_irq_handler,
+ IRQF_ONESHOT,
+ "Surface3-irq", data);
+ if (error)
+ return error;
+
+ return 0;
+}
+
+static int __maybe_unused surface3_spi_suspend(struct device *dev)
+{
+ struct spi_device *spi = to_spi_device(dev);
+ struct surface3_ts_data *data = spi_get_drvdata(spi);
+
+ disable_irq(data->spi->irq);
+
+ surface3_spi_power(data, false);
+
+ return 0;
+}
+
+static int __maybe_unused surface3_spi_resume(struct device *dev)
+{
+ struct spi_device *spi = to_spi_device(dev);
+ struct surface3_ts_data *data = spi_get_drvdata(spi);
+
+ surface3_spi_power(data, true);
+
+ enable_irq(data->spi->irq);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(surface3_spi_pm_ops,
+ surface3_spi_suspend,
+ surface3_spi_resume);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id surface3_spi_acpi_match[] = {
+ { "MSHW0037", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, surface3_spi_acpi_match);
+#endif
+
+static struct spi_driver surface3_spi_driver = {
+ .driver = {
+ .name = "Surface3-spi",
+ .acpi_match_table = ACPI_PTR(surface3_spi_acpi_match),
+ .pm = &surface3_spi_pm_ops,
+ },
+ .probe = surface3_spi_probe,
+};
+
+module_spi_driver(surface3_spi_driver);
+
+MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>");
+MODULE_DESCRIPTION("Surface 3 SPI touchscreen driver");
+MODULE_LICENSE("GPL v2");
int err;
/* Allocate memory for device */
- ts_dev = kzalloc(sizeof(struct titsc), GFP_KERNEL);
+ ts_dev = kzalloc(sizeof(*ts_dev), GFP_KERNEL);
input_dev = input_allocate_device();
if (!ts_dev || !input_dev) {
dev_err(&pdev->dev, "failed to allocate memory.\n");
input_set_abs_params(input_dev, ABS_PRESSURE, 0, max_p, fudge_p, 0);
if (np)
- touchscreen_parse_properties(input_dev, false);
+ touchscreen_parse_properties(input_dev, false, NULL);
input_dev->open = tsc200x_open;
input_dev->close = tsc200x_close;
w8001->pktlen = W8001_PKTLEN_TOUCH2FG;
__set_bit(BTN_TOOL_DOUBLETAP, dev->keybit);
- input_mt_init_slots(dev, 2, 0);
+ error = input_mt_init_slots(dev, 2, 0);
+ if (error) {
+ dev_err(&w8001->serio->dev,
+ "failed to initialize MT slots: %d\n", error);
+ return error;
+ }
+
input_set_abs_params(dev, ABS_MT_POSITION_X,
0, touch.x, 0, 0);
input_set_abs_params(dev, ABS_MT_POSITION_Y,
0, touch.y, 0, 0);
input_set_abs_params(dev, ABS_MT_TOOL_TYPE,
0, MT_TOOL_MAX, 0, 0);
+ input_abs_set_res(dev, ABS_MT_POSITION_X, touch.panel_res);
+ input_abs_set_res(dev, ABS_MT_POSITION_Y, touch.panel_res);
strlcat(basename, " 2FG", basename_sz);
if (w8001->max_pen_x && w8001->max_pen_y)
* @grab: input handle that currently has the device grabbed (via
* EVIOCGRAB ioctl). When a handle grabs a device it becomes sole
* recipient for all input events coming from the device
- * @event_lock: this spinlock is is taken when input core receives
+ * @event_lock: this spinlock is taken when input core receives
* and processes a new event for the device (in input_event()).
* Code that accesses and/or modifies parameters of a device
* (such as keymap or absmin, absmax, absfuzz, etc.) after device
#define _TOUCHSCREEN_H
struct input_dev;
+struct input_mt_pos;
-void touchscreen_parse_properties(struct input_dev *dev, bool multitouch);
+struct touchscreen_properties {
+ unsigned int max_x;
+ unsigned int max_y;
+ bool invert_x;
+ bool invert_y;
+ bool swap_x_y;
+};
+
+void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
+ struct touchscreen_properties *prop);
+
+void touchscreen_set_mt_pos(struct input_mt_pos *pos,
+ const struct touchscreen_properties *prop,
+ unsigned int x, unsigned int y);
+
+void touchscreen_report_pos(struct input_dev *input,
+ const struct touchscreen_properties *prop,
+ unsigned int x, unsigned int y,
+ bool multitouch);
#endif
projects / cascardo / linux.git / commitdiff