BCM11130, BCM11140, BCM11351, BCM28145, BCM28155, BCM21664
The enable method is specified by defining the following required
-properties in the "cpus" device tree node:
+properties in the "cpu" device tree node:
- enable-method = "brcm,bcm11351-cpu-method";
- secondary-boot-reg = <...>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
- enable-method = "brcm,bcm11351-cpu-method";
- secondary-boot-reg = <0x3500417c>;
cpu0: cpu@0 {
device_type = "cpu";
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <1>;
+ enable-method = "brcm,bcm11351-cpu-method";
+ secondary-boot-reg = <0x3500417c>;
};
};
--- /dev/null
+Broadcom Kona Family CPU Enable Method
+--------------------------------------
+This binding defines the enable method used for starting secondary
+CPUs in the following Broadcom SoCs:
+ BCM23550
+
+The enable method is specified by defining the following required
+properties in the "cpu" device tree node:
+ - enable-method = "brcm,bcm23550";
+ - secondary-boot-reg = <...>;
+
+The secondary-boot-reg property is a u32 value that specifies the
+physical address of the register used to request the ROM holding pen
+code release a secondary CPU. The value written to the register is
+formed by encoding the target CPU id into the low bits of the
+physical start address it should jump to.
+
+Example:
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <1>;
+ enable-method = "brcm,bcm23550";
+ secondary-boot-reg = <0x3500417c>;
+ };
+ };
--- /dev/null
+Broadcom BCM23550 device tree bindings
+--------------------------------------
+
+This document describes the device tree bindings for boards with the BCM23550
+SoC.
+
+Required root node property:
+ - compatible: brcm,bcm23550
+
+Example:
+ / {
+ model = "BCM23550 SoC";
+ compatible = "brcm,bcm23550";
+ [...]
+ }
"allwinner,sun6i-a31"
"allwinner,sun8i-a23"
"arm,realview-smp"
+ "brcm,bcm11351-cpu-method"
+ "brcm,bcm23550"
"brcm,bcm-nsp-smp"
"brcm,brahma-b15"
"marvell,armada-375-smp"
"qcom,gcc-msm8660"
"qcom,kpss-acc-v1"
"qcom,kpss-acc-v2"
+ "renesas,apmu"
"rockchip,rk3036-smp"
"rockchip,rk3066-smp"
"ste,dbx500-smp"
--- /dev/null
+* Hisilicon Hi3519 System Controller Block
+
+This bindings use the following binding:
+Documentation/devicetree/bindings/mfd/syscon.txt
+
+Required properties:
+- compatible: "hisilicon,hi3519-sysctrl".
+- reg: the register region of this block
+
+Examples:
+sysctrl: system-controller@12010000 {
+ compatible = "hisilicon,hi3519-sysctrl", "syscon";
+ reg = <0x12010000 0x1000>;
+};
-Olimex i.MX Platforms Device Tree Bindings
-------------------------------------------
+Olimex Device Tree Bindings
+---------------------------
+
+SAM9-L9260 Board
+Required root node properties:
+ - compatible = "olimex,sam9-l9260", "atmel,at91sam9260";
i.MX23 Olinuxino Low Cost Board
Required root node properties:
Required root node properties:
- compatible = "rockchip,rk3228-evb", "rockchip,rk3228";
+- Rockchip RK3229 Evaluation board:
+ - compatible = "rockchip,rk3229-evb", "rockchip,rk3229";
+
- Rockchip RK3399 evb:
Required root node properties:
- compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
- "hardkernel,odroid-u3" - for Exynos4412-based Hardkernel Odroid U3.
- "hardkernel,odroid-x" - for Exynos4412-based Hardkernel Odroid X.
- "hardkernel,odroid-x2" - for Exynos4412-based Hardkernel Odroid X2.
+ - "hardkernel,odroid-xu" - for Exynos5410-based Hardkernel Odroid XU.
- "hardkernel,odroid-xu3" - for Exynos5422-based Hardkernel Odroid XU3.
- "hardkernel,odroid-xu3-lite" - for Exynos5422-based Hardkernel
Odroid XU3 Lite board.
compatible = "renesas,ape6evm", "renesas,r8a73a4"
- Atmark Techno Armadillo-800 EVA
compatible = "renesas,armadillo800eva"
+ - Blanche (RTP0RC7792SEB00010S)
+ compatible = "renesas,blanche", "renesas,r8a7792"
- BOCK-W
compatible = "renesas,bockw", "renesas,r8a7778"
- Genmai (RTK772100BC00000BR)
nvidia,whistler
toradex,apalis_t30
toradex,apalis_t30-eval
+ toradex,apalis-tk1
+ toradex,apalis-tk1-eval
toradex,colibri_t20-512
+ toradex,colibri_t30
+ toradex,colibri_t30-eval-v3
toradex,iris
Trusted Foundations
- reg: Memory map of eDMA CC
- reg-names: "edma3_cc"
- interrupts: Interrupt lines for CCINT, MPERR and CCERRINT.
-- interrupt-names: "edma3_ccint", "emda3_mperr" and "edma3_ccerrint"
+- interrupt-names: "edma3_ccint", "edma3_mperr" and "edma3_ccerrint"
- ti,tptcs: List of TPTCs associated with the eDMA in the following form:
<&tptc_phandle TC_priority_number>. The highest priority is 0.
reg = <0x49000000 0x10000>;
reg-names = "edma3_cc";
interrupts = <12 13 14>;
- interrupt-names = "edma3_ccint", "emda3_mperr", "edma3_ccerrint";
+ interrupt-names = "edma3_ccint", "edma3_mperr", "edma3_ccerrint";
dma-requests = <64>;
#dma-cells = <2>;
--- /dev/null
+QCOM Secure Channel Manager (SCM)
+
+Qualcomm processors include an interface to communicate to the secure firmware.
+This interface allows for clients to request different types of actions. These
+can include CPU power up/down, HDCP requests, loading of firmware, and other
+assorted actions.
+
+Required properties:
+- compatible: must contain one of the following:
+ * "qcom,scm-apq8064" for APQ8064 platforms
+ * "qcom,scm-msm8660" for MSM8660 platforms
+ * "qcom,scm-msm8690" for MSM8690 platforms
+ * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc)
+- clocks: One to three clocks may be required based on compatible.
+ * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960"
+ * Core, iface, and bus clocks required for "qcom,scm"
+- clock-names: Must contain "core" for the core clock, "iface" for the interface
+ clock and "bus" for the bus clock per the requirements of the compatible.
+
+Example for MSM8916:
+
+ firmware {
+ scm {
+ compatible = "qcom,scm";
+ clocks = <&gcc GCC_CRYPTO_CLK> , <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ };
+ };
atmel,adc-res-names = "lowres", "highres";
atmel,adc-use-res = "lowres";
- trigger@0 {
- reg = <0>;
+ trigger0 {
trigger-name = "external-rising";
trigger-value = <0x1>;
trigger-external;
};
- trigger@1 {
- reg = <1>;
+ trigger1 {
trigger-name = "external-falling";
trigger-value = <0x2>;
trigger-external;
};
- trigger@2 {
- reg = <2>;
+ trigger2 {
trigger-name = "external-any";
trigger-value = <0x3>;
trigger-external;
};
- trigger@3 {
- reg = <3>;
+ trigger3 {
trigger-name = "continuous";
trigger-value = <0x6>;
};
- functions: "usb3-ss", "sata"
For Tegra210, the list of valid PHY nodes is given below:
-- utmi: utmi-0, utmi-1, utmi-2, utmi-3
+- usb2: usb2-0, usb2-1, usb2-2, usb2-3
- functions: "snps", "xusb", "uart"
- hsic: hsic-0, hsic-1
- functions: "snps", "xusb"
--- /dev/null
+DT bindings for the Renesas Advanced Power Management Unit
+
+Renesas R-Car line of SoCs utilize one or more APMU hardware units
+for CPU core power domain control including SMP boot and CPU Hotplug.
+
+Required properties:
+
+- compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback.
+ Examples with soctypes are:
+ - "renesas,r8a7790-apmu" (R-Car H2)
+ - "renesas,r8a7791-apmu" (R-Car M2-W)
+ - "renesas,r8a7792-apmu" (R-Car V2H)
+ - "renesas,r8a7793-apmu" (R-Car M2-N)
+ - "renesas,r8a7794-apmu" (R-Car E2)
+
+- reg: Base address and length of the I/O registers used by the APMU.
+
+- cpus: This node contains a list of CPU cores, which should match the order
+ of CPU cores used by the WUPCR and PSTR registers in the Advanced Power
+ Management Unit section of the device's datasheet.
+
+
+Example:
+
+This shows the r8a7791 APMU that can control CPU0 and CPU1.
+
+ apmu@e6152000 {
+ compatible = "renesas,r8a7791-apmu", "renesas,apmu";
+ reg = <0 0xe6152000 0 0x188>;
+ cpus = <&cpu0 &cpu1>;
+ };
Required properties:
- compatible: Must be "ti,<soc>-ecap".
- for am33xx - compatible = "ti,am33xx-ecap";
- for da850 - compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+ for am33xx - compatible = "ti,am3352-ecap", "ti,am33xx-ecap";
+ for am4372 - compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
+ for da850 - compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
+ for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap";
- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
the cells format. The PWM channel index ranges from 0 to 4. The only third
cell flag supported by this binding is PWM_POLARITY_INVERTED.
- reg: physical base address and size of the registers map.
Optional properties:
-- ti,hwmods: Name of the hwmod associated to the ECAP:
- "ecap<x>", <x> being the 0-based instance number from the HW spec
+- clocks: Handle to the ECAP's functional clock.
+- clock-names: Must be set to "fck".
Example:
-ecap0: ecap@0 { /* ECAP on am33xx */
- compatible = "ti,am33xx-ecap";
+ecap0: ecap@48300100 { /* ECAP on am33xx */
+ compatible = "ti,am3352-ecap", "ti,am33xx-ecap";
+ #pwm-cells = <3>;
+ reg = <0x48300100 0x80>;
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
+};
+
+ecap0: ecap@48300100 { /* ECAP on am4372 */
+ compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48300100 0x80>;
ti,hwmods = "ecap0";
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
+};
+
+ecap0: ecap@1f06000 { /* ECAP on da850 */
+ compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
+ #pwm-cells = <3>;
+ reg = <0x1f06000 0x80>;
};
-ecap0: ecap@0 { /* ECAP on da850 */
- compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+ecap0: ecap@4843e100 {
+ compatible = "ti,dra746-ecap", "ti,am3352-ecap";
#pwm-cells = <3>;
- reg = <0x306000 0x80>;
+ reg = <0x4843e100 0x80>;
+ clocks = <&l4_root_clk_div>;
+ clock-names = "fck";
};
Required properties:
- compatible: Must be "ti,<soc>-ehrpwm".
- for am33xx - compatible = "ti,am33xx-ehrpwm";
- for da850 - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+ for am33xx - compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
+ for am4372 - compatible = "ti,am4372-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
+ for da850 - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
+ for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm";
- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
- reg: physical base address and size of the registers map.
Optional properties:
-- ti,hwmods: Name of the hwmod associated to the EHRPWM:
- "ehrpwm<x>", <x> being the 0-based instance number from the HW spec
+- clocks: Handle to the PWM's time-base and functional clock.
+- clock-names: Must be set to "tbclk" and "fck".
Example:
-ehrpwm0: ehrpwm@0 { /* EHRPWM on am33xx */
- compatible = "ti,am33xx-ehrpwm";
+ehrpwm0: pwm@48300200 { /* EHRPWM on am33xx */
+ compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48300200 0x100>;
+ clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
+};
+
+ehrpwm0: pwm@48300200 { /* EHRPWM on am4372 */
+ compatible = "ti,am4372-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x48300200 0x80>;
+ clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
ti,hwmods = "ehrpwm0";
};
-ehrpwm0: ehrpwm@0 { /* EHRPWM on da850 */
- compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+ehrpwm0: pwm@1f00000 { /* EHRPWM on da850 */
+ compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x1f00000 0x2000>;
+};
+
+ehrpwm0: pwm@4843e200 { /* EHRPWM on dra746 */
+ compatible = "ti,dra746-ehrpwm", "ti,am3352-ehrpwm";
#pwm-cells = <3>;
- reg = <0x300000 0x2000>;
+ reg = <0x4843e200 0x80>;
+ clocks = <&ehrpwm0_tbclk>, <&l4_root_clk_div>;
+ clock-names = "tbclk", "fck";
};
TI SOC based PWM Subsystem
Required properties:
-- compatible: Must be "ti,am33xx-pwmss";
+- compatible: Must be "ti,<soc>-pwmss".
+ for am33xx - compatible = "ti,am33xx-pwmss";
+ for am4372 - compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+ for dra746 - compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss"
+
- reg: physical base address and size of the registers map.
- address-cells: Specify the number of u32 entries needed in child nodes.
Should set to 1.
Also child nodes should also populated under PWMSS DT node.
Example:
-pwmss0: pwmss@48300000 {
+epwmss0: epwmss@48300000 { /* PWMSS for am33xx */
compatible = "ti,am33xx-pwmss";
reg = <0x48300000 0x10>;
ti,hwmods = "epwmss0";
/* child nodes go here */
};
+
+epwmss0: epwmss@48300000 { /* PWMSS for am4372 */
+ compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"
+ reg = <0x48300000 0x10>;
+ ti,hwmods = "epwmss0";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+ ranges = <0x48300100 0x48300100 0x80 /* ECAP */
+ 0x48300180 0x48300180 0x80 /* EQEP */
+ 0x48300200 0x48300200 0x80>; /* EHRPWM */
+
+ /* child nodes go here */
+};
+
+epwmss0: epwmss@4843e000 { /* PWMSS for DRA7xx */
+ compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+ reg = <0x4843e000 0x30>;
+ ti,hwmods = "epwmss0";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /* child nodes go here */
+};
--- /dev/null
+Qualcomm WCNSS Binding
+
+This binding describes the Qualcomm WCNSS hardware. It consists of control
+block and a BT, WiFi and FM radio block, all using SMD as command channels.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be: "qcom,wcnss",
+
+- qcom,smd-channel:
+ Usage: required
+ Value type: <string>
+ Definition: standard SMD property specifying the SMD channel used for
+ communication with the WiFi firmware.
+ Should be "WCNSS_CTRL".
+
+- qcom,mmio:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: reference to a node specifying the wcnss "ccu" and "dxe"
+ register blocks. The node must be compatible with one of
+ the following:
+ "qcom,riva",
+ "qcom,pronto"
+
+= SUBNODES
+The subnodes of the wcnss node are optional and describe the individual blocks in
+the WCNSS.
+
+== Bluetooth
+The following properties are defined to the bluetooth node:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be:
+ "qcom,wcnss-bt"
+
+== WiFi
+The following properties are defined to the WiFi node:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,wcnss-wlan",
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the "rx" and "tx" interrupts
+
+- interrupt-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must contain "rx" and "tx"
+
+- qcom,smem-state:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should reference the tx-enable and tx-rings-empty SMEM states
+
+- qcom,smem-state-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must contain "tx-enable" and "tx-rings-empty"
+
+= EXAMPLE
+The following example represents a SMD node, with one edge representing the
+"pronto" subsystem, with the wcnss device and its wcn3680 BT and WiFi blocks
+described; as found on the 8974 platform.
+
+smd {
+ compatible = "qcom,smd";
+
+ pronto-edge {
+ interrupts = <0 142 1>;
+
+ qcom,ipc = <&apcs 8 17>;
+ qcom,smd-edge = <6>;
+
+ wcnss {
+ compatible = "qcom,wcnss";
+ qcom,smd-channels = "WCNSS_CTRL";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcom,mmio = <&pronto>;
+
+ bt {
+ compatible = "qcom,wcnss-bt";
+ };
+
+ wlan {
+ compatible = "qcom,wcnss-wlan";
+
+ interrupts = <0 145 0>, <0 146 0>;
+ interrupt-names = "tx", "rx";
+
+ qcom,smem-state = <&apps_smsm 10>, <&apps_smsm 9>;
+ qcom,smem-state-names = "tx-enable", "tx-rings-empty";
+ };
+ };
+ };
+};
+
+soc {
+ pronto: pronto {
+ compatible = "qcom,pronto";
+
+ reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
+ reg-names = "ccu", "dxe", "pmu";
+ };
+};
clock-names = "hclk", "pclk";
atmel,vbus-gpio = <&pioB 19 0>;
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
nvidia,xusb-padctl = <&padctl>;
- phys = <&{/padctl@0,7009f000/pads/usb2/usb2-1}>, /* mini-PCIe USB */
- <&{/padctl@0,7009f000/pads/usb2/usb2-2}>, /* USB A */
- <&{/padctl@0,7009f000/pads/pcie/pcie-0}>; /* USB A */
- phy-names = "utmi-1", "utmi-2", "usb3-0";
+ phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* mini-PCIe USB */
+ <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* USB A */
+ <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>; /* USB A */
+ phy-names = "usb2-1", "usb2-2", "usb3-0";
avddio-pex-supply = <&vdd_1v05_run>;
dvddio-pex-supply = <&vdd_1v05_run>;
dtb-$(CONFIG_MACH_ASM9260) += \
alphascale-asm9260-devkit.dtb
# Keep at91 dtb files sorted alphabetically for each SoC
-dtb-$(CONFIG_SOC_SAM_V4_V5) += \
+dtb-$(CONFIG_SOC_AT91RM9200) += \
at91rm9200ek.dtb \
- mpa1600.dtb \
+ mpa1600.dtb
+dtb-$(CONFIG_SOC_AT91SAM9) += \
animeo_ip.dtb \
at91-qil_a9260.dtb \
aks-cdu.dtb \
evk-pro3.dtb \
tny_a9260.dtb \
usb_a9260.dtb \
+ at91sam9260ek.dtb \
at91sam9261ek.dtb \
at91sam9263ek.dtb \
+ at91-sam9_l9260.dtb \
tny_a9263.dtb \
usb_a9263.dtb \
at91-foxg20.dtb \
bcm47094-dlink-dir-885l.dtb \
bcm94708.dtb \
bcm94709.dtb \
+ bcm953012er.dtb \
bcm953012k.dtb
dtb-$(CONFIG_ARCH_BCM_63XX) += \
bcm963138dvt.dtb
bcm958305k.dtb
dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
bcm28155-ap.dtb \
- bcm21664-garnet.dtb
+ bcm21664-garnet.dtb \
+ bcm23550-sparrow.dtb
dtb-$(CONFIG_ARCH_BCM_NSP) += \
+ bcm958525xmc.dtb \
+ bcm958625hr.dtb \
bcm958625k.dtb
dtb-$(CONFIG_ARCH_BERLIN) += \
berlin2-sony-nsz-gs7.dtb \
berlin2q-marvell-dmp.dtb
dtb-$(CONFIG_ARCH_BRCMSTB) += \
bcm7445-bcm97445svmb.dtb
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+ ep7211-edb7211.dtb
dtb-$(CONFIG_ARCH_DAVINCI) += \
da850-enbw-cmc.dtb \
da850-evm.dtb
exynos5250-snow-rev5.dtb \
exynos5250-spring.dtb \
exynos5260-xyref5260.dtb \
+ exynos5410-odroidxu.dtb \
exynos5410-smdk5410.dtb \
exynos5420-arndale-octa.dtb \
exynos5420-peach-pit.dtb \
exynos5800-peach-pi.dtb
dtb-$(CONFIG_ARCH_HI3xxx) += \
hi3620-hi4511.dtb
-dtb-$(CONFIG_ARCH_HIX5HD2) += \
- hisi-x5hd2-dkb.dtb
dtb-$(CONFIG_ARCH_HIGHBANK) += \
highbank.dtb \
ecx-2000.dtb
hip01-ca9x2.dtb
dtb-$(CONFIG_ARCH_HIP04) += \
hip04-d01.dtb
+dtb-$(CONFIG_ARCH_HISI) += \
+ hi3519-demb.dtb
+dtb-$(CONFIG_ARCH_HIX5HD2) += \
+ hisi-x5hd2-dkb.dtb
dtb-$(CONFIG_ARCH_INTEGRATOR) += \
integratorap.dtb \
integratorcp.dtb
imx6q-gw54xx.dtb \
imx6q-gw551x.dtb \
imx6q-gw552x.dtb \
+ imx6q-h100.dtb \
imx6q-hummingboard.dtb \
imx6q-icore-rqs.dtb \
imx6q-marsboard.dtb \
imx6q-tx6q-1110.dtb \
imx6q-tx6q-11x0-mb7.dtb \
imx6q-udoo.dtb \
+ imx6q-utilite-pro.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
imx6qp-nitrogen6_max.dtb \
imx6ul-tx6ul-mainboard.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
+ imx7d-colibri-eval-v3.dtb \
imx7d-nitrogen7.dtb \
imx7d-sbc-imx7.dtb \
- imx7d-sdb.dtb
+ imx7d-sdb.dtb \
+ imx7s-colibri-eval-v3.dtb
dtb-$(CONFIG_SOC_LS1021A) += \
ls1021a-qds.dtb \
ls1021a-twr.dtb
dtb-$(CONFIG_ARCH_MXS) += \
imx23-evk.dtb \
imx23-olinuxino.dtb \
+ imx23-sansa.dtb \
imx23-stmp378x_devb.dtb \
+ imx23-xfi3.dtb \
imx28-apf28.dtb \
imx28-apf28dev.dtb \
imx28-apx4devkit.dtb \
dtb-$(CONFIG_ARCH_OXNAS) += \
wd-mbwe.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-apq8064-arrow-db600c.dtb \
+ qcom-apq8060-dragonboard.dtb \
+ qcom-apq8064-arrow-sd-600eval.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
rk3066a-rayeager.dtb \
rk3188-radxarock.dtb \
rk3228-evb.dtb \
+ rk3229-evb.dtb \
rk3288-evb-act8846.dtb \
rk3288-evb-rk808.dtb \
rk3288-firefly-beta.dtb \
r8a7790-lager.dtb \
r8a7791-koelsch.dtb \
r8a7791-porter.dtb \
+ r8a7792-blanche.dtb \
r8a7793-gose.dtb \
r8a7794-alt.dtb \
r8a7794-silk.dtb \
sun6i-a31s-yones-toptech-bs1078-v2.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-bananapi.dtb \
+ sun7i-a20-bananapi-m1-plus.dtb \
sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a23-evb.dtb \
sun8i-a23-gt90h-v4.dtb \
+ sun8i-a23-inet86dz.dtb \
sun8i-a23-ippo-q8h-v5.dtb \
sun8i-a23-ippo-q8h-v1.2.dtb \
+ sun8i-a23-polaroid-mid2407pxe03.dtb \
sun8i-a23-polaroid-mid2809pxe04.dtb \
sun8i-a23-q8-tablet.dtb \
sun8i-a33-et-q8-v1.6.dtb \
sun8i-a33-sinlinx-sina33.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
sun8i-a83t-cubietruck-plus.dtb \
+ sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-one.dtb \
sun8i-h3-orangepi-pc.dtb \
- sun8i-h3-orangepi-plus.dtb
+ sun8i-h3-orangepi-plus.dtb \
+ sun8i-r16-parrot.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb
tegra114-roth.dtb \
tegra114-tn7.dtb
dtb-$(CONFIG_ARCH_TEGRA_124_SOC) += \
+ tegra124-apalis-eval.dtb \
tegra124-jetson-tk1.dtb \
tegra124-nyan-big.dtb \
tegra124-nyan-blaze.dtb \
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
reg = <0x80000000 0x10000000>; /* 256 MB */
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
leds {
pinctrl-names = "default";
pinctrl-0 = <&user_leds_s0>;
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
regulator-name = "vdd_mpu";
regulator-min-microvolt = <925000>;
- regulator-max-microvolt = <1325000>;
+ regulator-max-microvolt = <1351500>;
regulator-boot-on;
regulator-always-on;
};
phy-mode = "mii";
};
-&cpsw_emac1 {
- phy_id = <&davinci_mdio>, <1>;
- phy-mode = "mii";
-};
-
&mac {
+ slaves = <1>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cpsw_default>;
pinctrl-1 = <&cpsw_sleep>;
status = "okay";
};
+&cpu0_opp_table {
+ /*
+ * All PG 2.0 silicon may not support 1GHz but some of the early
+ * BeagleBone Blacks have PG 2.0 silicon which is guaranteed
+ * to support 1GHz OPP so enable it for PG 2.0 on this board.
+ */
+ oppnitro@1000000000 {
+ opp-supported-hw = <0x06 0x0100>;
+ };
+};
+
&am33xx_pinmux {
nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
pinctrl-single,pins = <
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
regulator-name = "vdd_mpu";
regulator-min-microvolt = <912500>;
- regulator-max-microvolt = <1312500>;
+ regulator-max-microvolt = <1351500>;
regulator-boot-on;
regulator-always-on;
};
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
regulator-name = "vdd_mpu";
regulator-min-microvolt = <912500>;
- regulator-max-microvolt = <1312500>;
+ regulator-max-microvolt = <1351500>;
regulator-boot-on;
regulator-always-on;
};
gpio-controller;
#gpio-cells = <2>;
};
+
+ pca9536: gpio@41 {
+ compatible = "ti,pca9536";
+ reg = <0x41>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
};
#include "tps65910.dtsi"
device_type = "cpu";
reg = <0>;
- /*
- * To consider voltage drop between PMIC and SoC,
- * tolerance value is reduced to 2% from 4% and
- * voltage value is increased as a precaution.
- */
- operating-points = <
- /* kHz uV */
- 720000 1285000
- 600000 1225000
- 500000 1125000
- 275000 1125000
- >;
- voltage-tolerance = <2>; /* 2 percentage */
+ operating-points-v2 = <&cpu0_opp_table>;
+ ti,syscon-efuse = <&scm_conf 0x7fc 0x1fff 0>;
+ ti,syscon-rev = <&scm_conf 0x600>;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
};
};
+ cpu0_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+
+ /*
+ * The three following nodes are marked with opp-suspend
+ * because the can not be enabled simultaneously on a
+ * single SoC.
+ */
+ opp50@300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ opp-microvolt = <950000 931000 969000>;
+ opp-supported-hw = <0x06 0x0010>;
+ opp-suspend;
+ };
+
+ opp100@275000000 {
+ opp-hz = /bits/ 64 <275000000>;
+ opp-microvolt = <1100000 1078000 1122000>;
+ opp-supported-hw = <0x01 0x00FF>;
+ opp-suspend;
+ };
+
+ opp100@300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ opp-microvolt = <1100000 1078000 1122000>;
+ opp-supported-hw = <0x06 0x0020>;
+ opp-suspend;
+ };
+
+ opp100@500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <1100000 1078000 1122000>;
+ opp-supported-hw = <0x01 0xFFFF>;
+ };
+
+ opp100@600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <1100000 1078000 1122000>;
+ opp-supported-hw = <0x06 0x0040>;
+ };
+
+ opp120@600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <1200000 1176000 1224000>;
+ opp-supported-hw = <0x01 0xFFFF>;
+ };
+
+ opp120@720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <1200000 1176000 1224000>;
+ opp-supported-hw = <0x06 0x0080>;
+ };
+
+ oppturbo@720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <1260000 1234800 1285200>;
+ opp-supported-hw = <0x01 0xFFFF>;
+ };
+
+ oppturbo@800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = <1260000 1234800 1285200>;
+ opp-supported-hw = <0x06 0x0100>;
+ };
+
+ oppnitro@1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <1325000 1298500 1351500>;
+ opp-supported-hw = <0x04 0x0200>;
+ };
+ };
+
pmu {
compatible = "arm,cortex-a8-pmu";
interrupts = <3>;
reg = <0x49000000 0x10000>;
reg-names = "edma3_cc";
interrupts = <12 13 14>;
- interrupt-names = "edma3_ccint", "emda3_mperr",
+ interrupt-names = "edma3_ccint", "edma3_mperr",
"edma3_ccerrint";
dma-requests = <64>;
#dma-cells = <2>;
0x48300200 0x48300200 0x80>; /* EHRPWM */
ecap0: ecap@48300100 {
- compatible = "ti,am33xx-ecap";
+ compatible = "ti,am3352-ecap",
+ "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48300100 0x80>;
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
interrupts = <31>;
interrupt-names = "ecap0";
- ti,hwmods = "ecap0";
status = "disabled";
};
ehrpwm0: pwm@48300200 {
- compatible = "ti,am33xx-ehrpwm";
+ compatible = "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48300200 0x80>;
- ti,hwmods = "ehrpwm0";
+ clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
0x48302200 0x48302200 0x80>; /* EHRPWM */
ecap1: ecap@48302100 {
- compatible = "ti,am33xx-ecap";
+ compatible = "ti,am3352-ecap",
+ "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48302100 0x80>;
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
interrupts = <47>;
interrupt-names = "ecap1";
- ti,hwmods = "ecap1";
status = "disabled";
};
ehrpwm1: pwm@48302200 {
- compatible = "ti,am33xx-ehrpwm";
+ compatible = "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48302200 0x80>;
- ti,hwmods = "ehrpwm1";
+ clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
0x48304200 0x48304200 0x80>; /* EHRPWM */
ecap2: ecap@48304100 {
- compatible = "ti,am33xx-ecap";
+ compatible = "ti,am3352-ecap",
+ "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48304100 0x80>;
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
interrupts = <61>;
interrupt-names = "ecap2";
- ti,hwmods = "ecap2";
status = "disabled";
};
ehrpwm2: pwm@48304200 {
- compatible = "ti,am33xx-ehrpwm";
+ compatible = "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48304200 0x80>;
- ti,hwmods = "ehrpwm2";
+ clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- vbat: fixedregulator@0 {
+ vbat: fixedregulator {
compatible = "regulator-fixed";
regulator-name = "vbat";
regulator-min-microvolt = <5000000>;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ ti,syscon-efuse = <&scm_conf 0x610 0x3f 0>;
+ ti,syscon-rev = <&scm_conf 0x600>;
+
clock-latency = <300000>; /* From omap-cpufreq driver */
};
};
+ cpu0_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+
+ opp50@300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ opp-microvolt = <950000 931000 969000>;
+ opp-supported-hw = <0xFF 0x01>;
+ opp-suspend;
+ };
+
+ opp100@600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <1100000 1078000 1122000>;
+ opp-supported-hw = <0xFF 0x04>;
+ };
+
+ opp120@720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <1200000 1176000 1224000>;
+ opp-supported-hw = <0xFF 0x08>;
+ };
+
+ oppturbo@800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = <1260000 1234800 1285200>;
+ opp-supported-hw = <0xFF 0x10>;
+ };
+
+ oppnitro@1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <1325000 1298500 1351500>;
+ opp-supported-hw = <0xFF 0x20>;
+ };
+ };
+
gic: interrupt-controller@48241000 {
compatible = "arm,cortex-a9-gic";
interrupt-controller;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "edma3_ccint", "emda3_mperr",
+ interrupt-names = "edma3_ccint", "edma3_mperr",
"edma3_ccerrint";
dma-requests = <64>;
#dma-cells = <2>;
status = "disabled";
ecap0: ecap@48300100 {
- compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ compatible = "ti,am4372-ecap",
+ "ti,am3352-ecap",
+ "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48300100 0x80>;
- ti,hwmods = "ecap0";
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
status = "disabled";
};
ehrpwm0: pwm@48300200 {
- compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ compatible = "ti,am4372-ehrpwm",
+ "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48300200 0x80>;
- ti,hwmods = "ehrpwm0";
+ clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
status = "disabled";
ecap1: ecap@48302100 {
- compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ compatible = "ti,am4372-ecap",
+ "ti,am3352-ecap",
+ "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48302100 0x80>;
- ti,hwmods = "ecap1";
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
status = "disabled";
};
ehrpwm1: pwm@48302200 {
- compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ compatible = "ti,am4372-ehrpwm",
+ "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48302200 0x80>;
- ti,hwmods = "ehrpwm1";
+ clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
status = "disabled";
ecap2: ecap@48304100 {
- compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ compatible = "ti,am4372-ecap",
+ "ti,am3352-ecap",
+ "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48304100 0x80>;
- ti,hwmods = "ecap2";
+ clocks = <&l4ls_gclk>;
+ clock-names = "fck";
status = "disabled";
};
ehrpwm2: pwm@48304200 {
- compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ compatible = "ti,am4372-ehrpwm",
+ "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48304200 0x80>;
- ti,hwmods = "ehrpwm2";
+ clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
status = "disabled";
ehrpwm3: pwm@48306200 {
- compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ compatible = "ti,am4372-ehrpwm",
+ "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48306200 0x80>;
- ti,hwmods = "ehrpwm3";
+ clocks = <&ehrpwm3_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
status = "disabled";
ehrpwm4: pwm@48308200 {
- compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ compatible = "ti,am4372-ehrpwm",
+ "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x48308200 0x80>;
- ti,hwmods = "ehrpwm4";
+ clocks = <&ehrpwm4_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
status = "disabled";
ehrpwm5: pwm@4830a200 {
- compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ compatible = "ti,am4372-ehrpwm",
+ "ti,am3352-ehrpwm",
+ "ti,am33xx-ehrpwm";
#pwm-cells = <3>;
reg = <0x4830a200 0x80>;
- ti,hwmods = "ehrpwm5";
+ clocks = <&ehrpwm5_tbclk>, <&l4ls_gclk>;
+ clock-names = "tbclk", "fck";
status = "disabled";
};
};
dma-names = "tx", "rx";
};
+ rng: rng@48310000 {
+ compatible = "ti,omap4-rng";
+ ti,hwmods = "rng";
+ reg = <0x48310000 0x2000>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
mcasp0: mcasp@48038000 {
compatible = "ti,am33xx-mcasp-audio";
ti,hwmods = "mcasp0";
pinctrl-0 = <&dss_pins>;
port {
- dpi_out: endpoint@0 {
+ dpi_out: endpoint {
remote-endpoint = <&lcd_in>;
data-lines = <24>;
};
clock-names = "ext-clk", "int-clk";
status = "okay";
};
+
+&cpu {
+ cpu0-supply = <&dcdc2>;
+};
};
&mac {
+ slaves = <1>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cpsw_default>;
pinctrl-1 = <&cpsw_sleep>;
pinctrl-0 = <&dss_pinctrl_default>;
port {
- dpi_lcd_out: endpoint@0 {
+ dpi_lcd_out: endpoint {
remote-endpoint = <&lcd_in>;
data-lines = <24>;
};
pinctrl-0 = <&dss_pins>;
port {
- dpi_out: endpoint@0 {
+ dpi_out: endpoint {
remote-endpoint = <&lcd_in>;
data-lines = <24>;
};
clock-div = <1>;
};
+ rng_fck: rng_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
ehrpwm0_tbclk: ehrpwm0_tbclk@664 {
#clock-cells = <0>;
compatible = "ti,gate-clock";
vdda_video-supply = <&ldoln_reg>;
port {
- dpi_lcd_out: endpoint@0 {
+ dpi_lcd_out: endpoint {
remote-endpoint = <&lcd_in>;
data-lines = <24>;
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <18432000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>;
status = "okay";
status = "okay";
};
- mdio@72004 {
- pinctrl-0 = <&mdio_pins>;
- pinctrl-names = "default";
-
- phy_dedicated: ethernet-phy@0 {
- /*
- * Annoyingly, the marvell phy driver
- * configures the LED register, rather
- * than preserving reset-loaded setting.
- * We undo that rubbish here.
- */
- marvell,reg-init = <3 16 0 0x101e>;
- reg = <0>;
- };
- };
-
pinctrl@18000 {
clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins {
marvell,pins = "mpp46";
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
- onewire@0 {
+ onewire {
compatible = "w1-gpio";
gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <18432000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
};
- i2c@0 {
+ i2c-gpio-0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c0>;
i2c-gpio,delay-us = <5>; /* ~85 kHz */
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <1>;
status = "okay";
};
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
rtc: pcf8563@51 {
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
};
};
--- /dev/null
+/*
+ * at91-sam9_l9260.dts - Device Tree file for Olimex SAM9-L9260 board
+ *
+ * Copyright (C) 2016 Raashid Muhammed <raashidmuhammed@zilogic.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9260.dtsi"
+
+/ {
+ model = "Olimex sam9-l9260";
+ compatible = "olimex,sam9-l9260", "atmel,at91sam9260", "atmel,at91sam9";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <18432000>;
+ };
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc@fffa8000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot1_cmd_dat0
+ &pinctrl_mmc0_slot1_dat1_3>;
+ status = "okay";
+
+ slot@1 {
+ reg = <1>;
+ bus-width = <4>;
+ cd-gpios = <&pioC 8 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&pioC 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ macb0: ethernet@fffc4000 {
+ pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii_alt>;
+ phy-mode = "mii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ };
+ };
+
+ spi0: spi@fffc8000 {
+ cs-gpios = <&pioC 11 0>, <0>, <0>, <0>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <15000000>;
+ reg = <0>;
+ };
+ };
+
+ dbgu: serial@fffff200 {
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOC 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* CD pin */
+ AT91_PIOC 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* WP pin */
+ };
+ };
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt = <1>;
+ status = "okay";
+ };
+
+ usb0: ohci@500000 {
+ status = "okay";
+ };
+
+ };
+
+ i2c-gpio-0 {
+ status = "okay";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "sam9-l9260:yellow:pwr";
+ gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
+ };
+
+ status_led {
+ label = "sam9-l9260:green:status";
+ gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "timer";
+ };
+ };
+};
i2c-sda-hold-time-ns = <350>;
status = "okay";
- pmic: act8865@5b {
- compatible = "active-semi,act8865";
+ pmic@5b {
+ compatible = "active-semi,act8945a";
reg = <0x5b>;
active-semi,vsel-high;
+ active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>;
+ active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>;
+ active-semi,irq_gpios = <&pioA 45 GPIO_ACTIVE_LOW>;
+ active-semi,input-voltage-threshold-microvolt = <6600>;
+ active-semi,precondition-timeout = <40>;
+ active-semi,total-timeout = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
status = "okay";
regulators {
- vdd_1v35_reg: DCDC_REG1 {
+ vdd_1v35_reg: REG_DCDC1 {
regulator-name = "VDD_1V35";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
- vdd_1v2_reg: DCDC_REG2 {
+ vdd_1v2_reg: REG_DCDC2 {
regulator-name = "VDD_1V2";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
};
- vdd_3v3_reg: DCDC_REG3 {
+ vdd_3v3_reg: REG_DCDC3 {
regulator-name = "VDD_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
- vdd_fuse_reg: LDO_REG1 {
+ vdd_fuse_reg: REG_LDO1 {
regulator-name = "VDD_FUSE";
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-always-on;
};
- vdd_3v3_lp_reg: LDO_REG2 {
+ vdd_3v3_lp_reg: REG_LDO2 {
regulator-name = "VDD_3V3_LP";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
- vdd_led_reg: LDO_REG3 {
+ vdd_led_reg: REG_LDO3 {
regulator-name = "VDD_LED";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
- vdd_sdhc_1v8_reg: LDO_REG4 {
+ vdd_sdhc_1v8_reg: REG_LDO4 {
regulator-name = "VDD_SDHC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
bias-disable;
};
+ pinctrl_charger_chglev: charger_chglev {
+ pinmux = <PIN_PA12__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_charger_irq: charger_irq {
+ pinmux = <PIN_PB13__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_charger_lbo: charger_lbo {
+ pinmux = <PIN_PC8__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_flx0_default: flx0_default {
pinmux = <PIN_PB28__FLEXCOM0_IO0>,
<PIN_PB29__FLEXCOM0_IO1>;
};
};
- vcc_mmc0_reg: fixedregulator@0 {
+ vcc_mmc0_reg: fixedregulator_mmc0 {
compatible = "regulator-fixed";
gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
regulator-name = "mmc0-card-supply";
};
clocks {
- main_clock: main_clock {
- compatible = "atmel,osc", "fixed-clock";
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
clock-frequency = <12000000>;
};
};
};
- vcc_3v3_reg: fixedregulator@0 {
+ vcc_3v3_reg: fixedregulator_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC 3V3";
regulator-min-microvolt = <3300000>;
regulator-always-on;
};
- vcc_mmc0_reg: fixedregulator@1 {
+ vcc_mmc0_reg: fixedregulator_mmc0 {
compatible = "regulator-fixed";
gpio = <&pioE 15 GPIO_ACTIVE_HIGH>;
regulator-name = "RST_n MCI0";
};
};
- vcc_mmc1_reg: fixedregulator@2 {
+ vcc_mmc1_reg: fixedregulator_mmc1 {
compatible = "regulator-fixed";
gpio = <&pioE 17 GPIO_ACTIVE_LOW>;
regulator-name = "VDD MCI1";
};
};
- vcc_3v3_reg: fixedregulator@0 {
+ vcc_3v3_reg: fixedregulator_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC 3V3";
regulator-min-microvolt = <3300000>;
regulator-always-on;
};
- vcc_mmc1_reg: fixedregulator@1 {
+ vcc_mmc1_reg: fixedregulator_mmc1 {
compatible = "regulator-fixed";
gpio = <&pioE 4 GPIO_ACTIVE_LOW>;
regulator-name = "VDD MCI1";
ahb {
apb {
- lcd_bus@f0000000 {
- status = "okay";
-
- lcd@f0000000 {
- status = "okay";
- };
-
- lcdovl1@f0000140 {
- status = "okay";
- };
-
- lcdovl2@f0000240 {
- status = "okay";
- };
-
- lcdheo1@f0000340 {
- status = "okay";
- };
- };
-
adc0: adc@fc034000 {
pinctrl-names = "default";
pinctrl-0 = <
};
- vcc_3v3_reg: fixedregulator@0 {
+ vcc_3v3_reg: fixedregulator_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC 3V3";
regulator-min-microvolt = <3300000>;
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 25 GPIO_ACTIVE_HIGH /* sda */
&pioA 26 GPIO_ACTIVE_HIGH /* scl */
atmel,adc-res-names = "lowres", "highres";
atmel,adc-use-res = "highres";
- trigger@0 {
- reg = <0>;
+ trigger0 {
trigger-name = "timer-counter-0";
trigger-value = <0x1>;
};
- trigger@1 {
- reg = <1>;
+ trigger1 {
trigger-name = "timer-counter-1";
trigger-value = <0x3>;
};
- trigger@2 {
- reg = <2>;
+ trigger2 {
trigger-name = "timer-counter-2";
trigger-value = <0x5>;
};
- trigger@3 {
- reg = <3>;
+ trigger3 {
trigger-name = "external";
trigger-value = <0xd>;
trigger-external;
status = "disabled";
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x100000>;
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */
&pioA 24 GPIO_ACTIVE_HIGH /* scl */
--- /dev/null
+/*
+ * Device Tree file for Atmel at91sam9260 Evaluation Kit
+ *
+ * Copyright (C) 2016 Atmel,
+ * 2016 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "at91sam9260.dtsi"
+
+/ {
+ model = "Atmel at91sam9260ek";
+ compatible = "atmel,at91sam9260ek", "atmel,at91sam9260", "atmel,at91sam9";
+
+ chosen {
+ stdout-path = &dbgu;
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <18432000>;
+ };
+ };
+
+ ahb {
+ apb {
+ usb1: gadget@fffa4000 {
+ atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ mmc0: mmc@fffa8000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0_slot1
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot1_cmd_dat0
+ &pinctrl_mmc0_slot1_dat1_3>;
+ status = "okay";
+ slot@1 {
+ reg = <1>;
+ bus-width = <4>;
+ cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ usart0: serial@fffb0000 {
+ pinctrl-0 =
+ <&pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts
+ &pinctrl_usart0_dtr_dsr
+ &pinctrl_usart0_dcd
+ &pinctrl_usart0_ri>;
+ status = "okay";
+ };
+
+ usart1: serial@fffb4000 {
+ status = "okay";
+ };
+
+ ssc0: ssc@fffbc000 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_ssc0_tx>;
+ };
+
+ macb0: ethernet@fffc4000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ spi0: spi@fffc8000 {
+ cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <50000000>;
+ reg = <1>;
+ };
+ };
+
+ dbgu: serial@fffff200 {
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ board {
+ pinctrl_board_mmc0_slot1: mmc0_slot1-board {
+ atmel,pins =
+ <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ };
+ };
+
+ shdwc@fffffd10 {
+ atmel,wakeup-counter = <10>;
+ atmel,wakeup-rtt-timer;
+ };
+
+ rtc@fffffd20 {
+ atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+ status = "okay";
+ };
+
+ watchdog@fffffd40 {
+ status = "okay";
+ };
+
+ gpbr: syscon@fffffd50 {
+ status = "okay";
+ };
+ };
+
+ usb0: ohci@500000 {
+ num-ports = <2>;
+ status = "okay";
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ btn3 {
+ label = "Button 3";
+ gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
+ linux,code = <0x103>;
+ gpio-key,wakeup;
+ };
+
+ btn4 {
+ label = "Button 4";
+ gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ gpio-key,wakeup;
+ };
+ };
+
+ i2c-gpio-0 {
+ status = "okay";
+
+ 24c512@50 {
+ compatible = "24c512";
+ reg = <0x50>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ds1 {
+ label = "ds1";
+ gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds5 {
+ label = "ds5";
+ gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c_bitbang>;
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
&pioB 5 GPIO_ACTIVE_HIGH /* scl */
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
24c512@50 {
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
24c512@50 {
i2c0: i2c@f8010000 {
ov2640: camera@0x30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
+ clocks = <&pck0>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck0>;
+ assigned-clock-rates = <25000000>;
status = "okay";
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
};
};
isi: isi@f8048000 {
status = "okay";
+ port {
+ isi_0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ vsync-active = <1>;
+ hsync-active = <1>;
+ };
+ };
};
};
};
atmel,adc-res-names = "lowres", "highres";
atmel,adc-use-res = "highres";
- trigger@0 {
- reg = <0>;
+ trigger0 {
trigger-name = "external-rising";
trigger-value = <0x1>;
trigger-external;
};
- trigger@1 {
- reg = <1>;
+ trigger1 {
trigger-name = "external-falling";
trigger-value = <0x2>;
trigger-external;
};
- trigger@2 {
- reg = <2>;
+ trigger2 {
trigger-name = "external-any";
trigger-value = <0x3>;
trigger-external;
};
- trigger@3 {
- reg = <3>;
+ trigger3 {
trigger-name = "continuous";
trigger-value = <0x6>;
};
clock-names = "pclk", "hclk";
status = "disabled";
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */
&pioA 21 GPIO_ACTIVE_HIGH /* scl */
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
&pioA 31 GPIO_ACTIVE_HIGH /* scl */
atmel,adc-res-names = "lowres", "highres";
atmel,adc-use-res = "highres";
- trigger@0 {
- reg = <0>;
+ trigger0 {
trigger-name = "timer-counter-0";
trigger-value = <0x1>;
};
- trigger@1 {
- reg = <1>;
+ trigger1 {
trigger-name = "timer-counter-1";
trigger-value = <0x3>;
};
- trigger@2 {
- reg = <2>;
+ trigger2 {
trigger-name = "timer-counter-2";
trigger-value = <0x5>;
};
- trigger@3 {
- reg = <3>;
+ trigger3 {
trigger-name = "external";
trigger-value = <0x13>;
trigger-external;
clock-names = "pclk", "hclk";
status = "disabled";
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 23 GPIO_ACTIVE_HIGH>, /* sda */
<&pioA 24 GPIO_ACTIVE_HIGH>; /* scl */
status = "disabled";
};
- i2c@1 {
+ i2c-gpio-1 {
compatible = "i2c-gpio";
gpios = <&pioD 10 GPIO_ACTIVE_HIGH>, /* sda */
<&pioD 11 GPIO_ACTIVE_HIGH>; /* scl */
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
};
- i2c@1 {
+ i2c-gpio-1 {
status = "okay";
};
};
atmel,adc-res-names = "lowres", "highres";
atmel,adc-use-res = "highres";
- trigger@0 {
- reg = <0>;
+ trigger0 {
trigger-name = "external-rising";
trigger-value = <0x1>;
trigger-external;
};
- trigger@1 {
- reg = <1>;
+ trigger1 {
trigger-name = "external-falling";
trigger-value = <0x2>;
trigger-external;
};
- trigger@2 {
- reg = <2>;
+ trigger2 {
trigger-name = "external-any";
trigger-value = <0x3>;
trigger-external;
};
- trigger@3 {
- reg = <3>;
+ trigger3 {
trigger-name = "continuous";
trigger-value = <0x6>;
};
clock-names = "hclk", "pclk";
status = "disabled";
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
&pioA 31 GPIO_ACTIVE_HIGH /* scl */
status = "disabled";
};
- i2c@1 {
+ i2c-gpio-1 {
compatible = "i2c-gpio";
gpios = <&pioC 0 GPIO_ACTIVE_HIGH /* sda */
&pioC 1 GPIO_ACTIVE_HIGH /* scl */
status = "disabled";
};
- i2c@2 {
+ i2c-gpio-2 {
compatible = "i2c-gpio";
gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
&pioB 5 GPIO_ACTIVE_HIGH /* scl */
status = "okay";
};
- isi: isi@f8048000 {
- status = "disabled";
- port {
- isi_0: endpoint@0 {
- remote-endpoint = <&ov2640_0>;
- bus-width = <8>;
- vsync-active = <1>;
- hsync-active = <1>;
- };
- };
- };
-
i2c0: i2c@f8010000 {
status = "okay";
compatible = "wm8731";
reg = <0x1a>;
};
-
- ov2640: camera@0x30 {
- compatible = "ovti,ov2640";
- reg = <0x30>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
- resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
- pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
- clocks = <&pck0>;
- clock-names = "xvclk";
- assigned-clocks = <&pck0>;
- assigned-clock-rates = <25000000>;
- status = "disabled";
-
- port {
- ov2640_0: endpoint {
- remote-endpoint = <&isi_0>;
- bus-width = <8>;
- };
- };
- };
};
adc0: adc@f804c000 {
reg_ldo5: ldo5 {
regulator-name = "ldo5";
+ status = "disabled";
};
};
reg_ldo_io0: ldo_io0 {
regulator-name = "ldo_io0";
+ status = "disabled";
};
reg_ldo_io1: ldo_io1 {
regulator-name = "ldo_io1";
+ status = "disabled";
};
reg_rtc_ldo: rtc_ldo {
regulator-max-microvolt = <3000000>;
regulator-name = "rtc_ldo";
};
+
+ reg_drivevbus: drivevbus {
+ regulator-name = "drivevbus";
+ status = "disabled";
+ };
+ };
+
+ usb_power_supply: usb_power_supply {
+ compatible = "x-powers,axp221-usb-power-supply";
+ status = "disabled";
};
};
--- /dev/null
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * AXP809 Integrated Power Management Chip
+ */
+
+&axp809 {
+ compatible = "x-powers,axp809";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+};
interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
+
+ adc: adc@180a6000 {
+ compatible = "brcm,iproc-static-adc";
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+ adc-syscon = <&ts_adc_syscon>;
+ clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>;
+ clock-names = "tsc_clk";
+ interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
};
};
compatible = "arm,cortex-a9";
next-level-cache = <&L2>;
enable-method = "brcm,bcm-nsp-smp";
- secondary-boot-reg = <0xffff042c>;
+ secondary-boot-reg = <0xffff0fec>;
reg = <0x1>;
};
};
status = "disabled";
};
+ dma@20000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x20000 0x1000>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&iprocslow>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ };
+
nand: nand@26000 {
compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
reg = <0x026000 0x600>,
ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
status = "disabled";
+
+ msi-parent = <&msi0>;
+ msi0: msi@18012000 {
+ compatible = "brcm,iproc-msi";
+ msi-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
+ <GIC_SPI 128 IRQ_TYPE_NONE>,
+ <GIC_SPI 129 IRQ_TYPE_NONE>,
+ <GIC_SPI 130 IRQ_TYPE_NONE>;
+ brcm,pcie-msi-inten;
+ };
};
pcie1: pcie@18013000 {
ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
status = "disabled";
+
+ msi-parent = <&msi1>;
+ msi1: msi@18013000 {
+ compatible = "brcm,iproc-msi";
+ msi-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_NONE>,
+ <GIC_SPI 134 IRQ_TYPE_NONE>,
+ <GIC_SPI 135 IRQ_TYPE_NONE>,
+ <GIC_SPI 136 IRQ_TYPE_NONE>;
+ brcm,pcie-msi-inten;
+ };
};
pcie2: pcie@18014000 {
ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
status = "disabled";
+
+ msi-parent = <&msi2>;
+ msi2: msi@18014000 {
+ compatible = "brcm,iproc-msi";
+ msi-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>,
+ <GIC_SPI 140 IRQ_TYPE_NONE>,
+ <GIC_SPI 141 IRQ_TYPE_NONE>,
+ <GIC_SPI 142 IRQ_TYPE_NONE>;
+ brcm,pcie-msi-inten;
+ };
};
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
- enable-method = "brcm,bcm11351-cpu-method";
cpu0: cpu@0 {
device_type = "cpu";
cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
+ enable-method = "brcm,bcm11351-cpu-method";
secondary-boot-reg = <0x3500417c>;
reg = <1>;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
- enable-method = "brcm,bcm11351-cpu-method";
cpu0: cpu@0 {
device_type = "cpu";
cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
+ enable-method = "brcm,bcm11351-cpu-method";
secondary-boot-reg = <0x35004178>;
reg = <1>;
};
--- /dev/null
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2016 Broadcom. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm23550.dtsi"
+
+/ {
+ model = "BCM23550 Sparrow board";
+ compatible = "brcm,bcm23550-sparrow", "brcm,bcm23550";
+
+ chosen {
+ stdout-path = "/slaves@3e000000/serial@0:115200n8";
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ memory {
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+};
+
+&uartb {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&sdio1 {
+ max-frequency = <48000000>;
+ status = "okay";
+};
+
+&sdio2 {
+ non-removable;
+ max-frequency = <48000000>;
+ status = "okay";
+};
+
+&sdio4 {
+ max-frequency = <48000000>;
+ cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2016 Broadcom. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/* BCM23550 and BCM21664 have almost identical clocks */
+#include "dt-bindings/clock/bcm21664.h"
+
+#include "skeleton.dtsi"
+
+/ {
+ model = "BCM23550 SoC";
+ compatible = "brcm,bcm23550";
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0>;
+ clock-frequency = <1000000000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ enable-method = "brcm,bcm23550";
+ secondary-boot-reg = <0x35004178>;
+ reg = <1>;
+ clock-frequency = <1000000000>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ enable-method = "brcm,bcm23550";
+ secondary-boot-reg = <0x35004178>;
+ reg = <2>;
+ clock-frequency = <1000000000>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ enable-method = "brcm,bcm23550";
+ secondary-boot-reg = <0x35004178>;
+ reg = <3>;
+ clock-frequency = <1000000000>;
+ };
+ };
+
+ /* Hub bus */
+ hub@34000000 {
+ compatible = "simple-bus";
+ ranges = <0 0x34000000 0x102f83ac>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ smc@4e000 {
+ compatible = "brcm,bcm23550-smc", "brcm,kona-smc";
+ reg = <0x0004e000 0x400>; /* 1 KiB in SRAM */
+ };
+
+ resetmgr: reset-controller@1001f00 {
+ compatible = "brcm,bcm21664-resetmgr";
+ reg = <0x01001f00 0x24>;
+ };
+
+ gpio: gpio@1003000 {
+ compatible = "brcm,bcm23550-gpio", "brcm,kona-gpio";
+ reg = <0x01003000 0x524>;
+ interrupts =
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ timer@1006000 {
+ compatible = "brcm,kona-timer";
+ reg = <0x01006000 0x1c>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&aon_ccu BCM21664_AON_CCU_HUB_TIMER>;
+ };
+ };
+
+ /* Slaves bus */
+ slaves@3e000000 {
+ compatible = "simple-bus";
+ ranges = <0 0x3e000000 0x0001c070>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uartb: serial@0 {
+ compatible = "snps,dw-apb-uart";
+ status = "disabled";
+ reg = <0x00000000 0x118>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ uartb2: serial@1000 {
+ compatible = "snps,dw-apb-uart";
+ status = "disabled";
+ reg = <0x00001000 0x118>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ uartb3: serial@2000 {
+ compatible = "snps,dw-apb-uart";
+ status = "disabled";
+ reg = <0x00002000 0x118>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ bsc1: i2c@16000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x00016000 0x70>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC1>;
+ status = "disabled";
+ };
+
+ bsc2: i2c@17000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x00017000 0x70>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC2>;
+ status = "disabled";
+ };
+
+ bsc3: i2c@18000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x00018000 0x70>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC3>;
+ status = "disabled";
+ };
+
+ bsc4: i2c@1c000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x0001c000 0x70>;
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC4>;
+ status = "disabled";
+ };
+ };
+
+ /* Apps bus */
+ apps@3e300000 {
+ compatible = "simple-bus";
+ ranges = <0 0x3e300000 0x01b77000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ usbotg: usb@e20000 {
+ compatible = "snps,dwc2";
+ reg = <0x00e20000 0x10000>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_otg_ahb_clk>;
+ clock-names = "otg";
+ phys = <&usbphy>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+
+ usbphy: usb-phy@e30000 {
+ compatible = "brcm,kona-usb2-phy";
+ reg = <0x00e30000 0x28>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ sdio1: sdio@e80000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00e80000 0x801c>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO1>;
+ status = "disabled";
+ };
+
+ sdio2: sdio@e90000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00e90000 0x801c>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO2>;
+ status = "disabled";
+ };
+
+ sdio3: sdio@ea0000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00ea0000 0x801c>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO3>;
+ status = "disabled";
+ };
+
+ sdio4: sdio@eb0000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00eb0000 0x801c>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO4>;
+ status = "disabled";
+ };
+
+ cdc: cdc@1b0e000 {
+ compatible = "brcm,bcm23550-cdc";
+ reg = <0x01b0e000 0x78>;
+ };
+
+ gic: interrupt-controller@1b21000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x01b21000 0x1000>,
+ <0x01b22000 0x1000>;
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /*
+ * Fixed clocks are defined before CCUs whose
+ * clocks may depend on them.
+ */
+
+ ref_32k_clk: ref_32k {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ bbl_32k_clk: bbl_32k {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ ref_13m_clk: ref_13m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <13000000>;
+ };
+
+ var_13m_clk: var_13m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <13000000>;
+ };
+
+ dft_19_5m_clk: dft_19_5m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <19500000>;
+ };
+
+ ref_crystal_clk: ref_crystal {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ };
+
+ ref_52m_clk: ref_52m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <52000000>;
+ };
+
+ var_52m_clk: var_52m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <52000000>;
+ };
+
+ usb_otg_ahb_clk: usb_otg_ahb {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <52000000>;
+ };
+
+ ref_96m_clk: ref_96m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <96000000>;
+ };
+
+ var_96m_clk: var_96m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <96000000>;
+ };
+
+ ref_104m_clk: ref_104m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <104000000>;
+ };
+
+ var_104m_clk: var_104m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <104000000>;
+ };
+
+ ref_156m_clk: ref_156m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <156000000>;
+ };
+
+ var_156m_clk: var_156m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <156000000>;
+ };
+
+ root_ccu: root_ccu {
+ compatible = BCM21664_DT_ROOT_CCU_COMPAT;
+ reg = <0x35001000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "frac_1m";
+ };
+
+ aon_ccu: aon_ccu {
+ compatible = BCM21664_DT_AON_CCU_COMPAT;
+ reg = <0x35002000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "hub_timer";
+ };
+
+ slave_ccu: slave_ccu {
+ compatible = BCM21664_DT_SLAVE_CCU_COMPAT;
+ reg = <0x3e011000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "uartb",
+ "uartb2",
+ "uartb3",
+ "bsc1",
+ "bsc2",
+ "bsc3",
+ "bsc4";
+ };
+
+ master_ccu: master_ccu {
+ compatible = BCM21664_DT_MASTER_CCU_COMPAT;
+ reg = <0x3f001000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "sdio1",
+ "sdio2",
+ "sdio3",
+ "sdio4",
+ "sdio1_sleep",
+ "sdio2_sleep",
+ "sdio3_sleep",
+ "sdio4_sleep";
+ };
+ };
+};
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
/ {
compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
/ {
compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
/ {
compatible = "raspberrypi,model-b", "brcm,bcm2835";
/dts-v1/;
#include "bcm2836.dtsi"
#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
/ {
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
--- /dev/null
+/ {
+ aliases {
+ ethernet = ðernet;
+ };
+};
+
+&usb {
+ usb1@1 {
+ compatible = "usb424,9512";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: usbether@1 {
+ compatible = "usb424,ec00";
+ reg = <1>;
+ };
+ };
+};
--- /dev/null
+/ {
+ aliases {
+ ethernet = ðernet;
+ };
+};
+
+&usb {
+ usb1@1 {
+ compatible = "usb424,9514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: usbether@1 {
+ compatible = "usb424,ec00";
+ reg = <1>;
+ };
+ };
+};
compatible = "brcm,bcm2835-usb";
reg = <0x7e980000 0x10000>;
interrupts = <1 9>;
+ #address-cells = <1>;
+ #size-cells = <0>;
};
v3d: v3d@7ec00000 {
&usb3 {
vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
};
+
+&spi_nor {
+ status = "okay";
+};
&usb3 {
vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
};
+
+&spi_nor {
+ status = "okay";
+};
};
};
};
+
+&spi_nor {
+ status = "okay";
+};
&spi_nor {
status = "okay";
};
+
+&srab {
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan4";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan1";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ };
+ };
+};
&usb2 {
vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
};
+
+&spi_nor {
+ status = "okay";
+};
/dts-v1/;
#include "bcm4708.dtsi"
-#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include "bcm5301x-nand-cs0-bch1.dtsi"
/ {
compatible = "dlink,dir-885l", "brcm,bcm47094", "brcm,bcm4708";
&usb3 {
vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
};
+
+&spi_nor {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Broadcom Northstar NAND.
+ *
+ * Copyright (C) 2016 Rafał Miłecki <rafal.milecki@gmail.com>
+ *
+ * Licensed under the ISC license.
+ */
+
+#include "bcm5301x-nand-cs0.dtsi"
+
+&nandcs {
+ nand-ecc-algo = "bch";
+ nand-ecc-strength = <1>;
+ nand-ecc-step-size = <512>;
+};
* Licensed under the GNU/GPL. See COPYING for details.
*/
-/ {
- nand@18028000 {
- nandcs@0 {
- compatible = "brcm,nandcs";
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
+#include "bcm5301x-nand-cs0.dtsi"
- nand-ecc-strength = <8>;
- nand-ecc-step-size = <512>;
- };
- };
+&nandcs {
+ nand-ecc-algo = "bch";
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
};
--- /dev/null
+/*
+ * Broadcom Northstar NAND.
+ *
+ * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/ {
+ nand@18028000 {
+ nandcs: nandcs@0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+};
/* ChipCommon */
<0x00000000 0 &gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+ /* Switch Register Access Block */
+ <0x00007000 0 &gic GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 1 &gic GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 2 &gic GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 3 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 4 &gic GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 5 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 6 &gic GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 7 &gic GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 8 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 9 &gic GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 10 &gic GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 11 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <0x00007000 12 &gic GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+
/* PCIe Controller 0 */
<0x00012000 0 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
<0x00012000 1 &gic GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
status = "disabled";
};
};
+
+ gmac0: ethernet@24000 {
+ reg = <0x24000 0x800>;
+ };
+
+ gmac1: ethernet@25000 {
+ reg = <0x25000 0x800>;
+ };
+
+ gmac2: ethernet@26000 {
+ reg = <0x26000 0x800>;
+ };
+
+ gmac3: ethernet@27000 {
+ reg = <0x27000 0x800>;
+ };
};
lcpll0: lcpll0@1800c100 {
"sata2";
};
+ srab: srab@18007000 {
+ compatible = "brcm,bcm5301x-srab";
+ reg = <0x18007000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ /* ports are defined in board DTS */
+ };
+
+ rng: rng@18004000 {
+ compatible = "brcm,bcm5301x-rng";
+ reg = <0x18004000 0x14>;
+ };
+
nand: nand@18028000 {
compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>;
--- /dev/null
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2016 Broadcom. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+ model = "NorthStar Enterprise Router (BCM953012ER)";
+ compatible = "brcm,bcm953012er", "brcm,brcm53012", "brcm,bcm4708";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x00000000 0x8000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wps {
+ label = "WPS";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+ };
+
+ restart {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&spi_nor {
+ status = "okay";
+};
+
+&srab {
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "port0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "port1";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ };
+ };
+};
--- /dev/null
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2016 Broadcom. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+
+/ {
+ model = "NorthStar Plus XMC (BCM958525xmc)";
+ compatible = "brcm,bcm58525", "brcm,nsp";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&nand {
+ nandcs@0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ nand-on-flash-bbt;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nand-ecc-strength = <24>;
+ nand-ecc-step-size = <1024>;
+
+ brcm,nand-oob-sector-size = <27>;
+
+ partition@0 {
+ label = "nboot";
+ reg = <0x00000000 0x00200000>;
+ read-only;
+ };
+ partition@200000 {
+ label = "nenv";
+ reg = <0x00200000 0x00400000>;
+ };
+ partition@600000 {
+ label = "nsystem";
+ reg = <0x00600000 0x00a00000>;
+ };
+ partition@1000000 {
+ label = "nrootfs";
+ reg = <0x01000000 0x03000000>;
+ };
+ partition@4000000 {
+ label = "ncustfs";
+ reg = <0x04000000 0x3c000000>;
+ };
+ };
+};
+
+/* XHCI, SATA, MMC, and Ethernet support needed to be complete */
+
+&uart0 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_sel>;
+ nand_sel: nand_sel {
+ function = "nand";
+ groups = "nand_grp";
+ };
+};
--- /dev/null
+/*
+ * BSD LICENSE
+ *
+ * Copyright (c) 2016 Broadcom. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+
+/ {
+ model = "NorthStar Plus SVK (BCM958625HR)";
+ compatible = "brcm,bcm58625", "brcm,nsp";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x60000000 0x20000000>;
+ };
+};
+
+&nand {
+ nandcs@0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ nand-on-flash-bbt;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nand-ecc-strength = <24>;
+ nand-ecc-step-size = <1024>;
+
+ brcm,nand-oob-sector-size = <27>;
+
+ partition@0 {
+ label = "nboot";
+ reg = <0x00000000 0x00200000>;
+ read-only;
+ };
+ partition@200000 {
+ label = "nenv";
+ reg = <0x00200000 0x00400000>;
+ };
+ partition@600000 {
+ label = "nsystem";
+ reg = <0x00600000 0x00a00000>;
+ };
+ partition@1000000 {
+ label = "nrootfs";
+ reg = <0x01000000 0x03000000>;
+ };
+ partition@4000000 {
+ label = "ncustfs";
+ reg = <0x04000000 0x3c000000>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_sel>;
+ nand_sel: nand_sel {
+ function = "nand";
+ groups = "nand_grp";
+ };
+};
};
};
- hdmi_conn: connector@0 {
+ hdmi_conn: connector {
compatible = "hdmi-connector";
label = "hdmi";
reg = <0x49000000 0x10000>;
reg-names = "edma3_cc";
interrupts = <12 13 14>;
- interrupt-names = "edma3_ccint", "emda3_mperr",
+ interrupt-names = "edma3_ccint", "edma3_mperr",
"edma3_ccerrint";
dma-requests = <64>;
#dma-cells = <2>;
interrupt-parent = <&gic>;
};
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <0>;
+
+ operating-points-v2 = <&cpu0_opp_table>;
+ ti,syscon-efuse = <&scm_wkup 0x20c 0xf80000 19>;
+ ti,syscon-rev = <&scm_wkup 0x204>;
+
+ clocks = <&dpll_mpu_ck>;
+ clock-names = "cpu";
+
+ clock-latency = <300000>; /* From omap-cpufreq driver */
+
+ /* cooling options */
+ cooling-min-level = <0>;
+ cooling-max-level = <2>;
+ #cooling-cells = <2>; /* min followed by max */
+ };
+ };
+
+ cpu0_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp_nom@1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <1060000 850000 1150000>;
+ opp-supported-hw = <0xFF 0x01>;
+ opp-suspend;
+ };
+
+ opp_od@1176000000 {
+ opp-hz = /bits/ 64 <1176000000>;
+ opp-microvolt = <1160000 885000 1160000>;
+ opp-supported-hw = <0xFF 0x02>;
+ };
+ };
+
/*
* The soc node represents the soc top level view. It is used for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
prm_clockdomains: clockdomains {
};
};
+
+ scm_wkup: scm_conf@c000 {
+ compatible = "syscon";
+ reg = <0xc000 0x1000>;
+ };
};
axi@0 {
ranges = <0x51800000 0x51800000 0x3000
0x0 0x30000000 0x10000000>;
status = "disabled";
- pcie@51000000 {
+ pcie@51800000 {
compatible = "ti,dra7-pcie";
reg = <0x51800000 0x2000>, <0x51802000 0x14c>, <0x1000 0x2000>;
reg-names = "rc_dbics", "ti_conf", "config";
};
};
+ ocmcram1: ocmcram@40300000 {
+ compatible = "mmio-sram";
+ reg = <0x40300000 0x80000>;
+ ranges = <0x0 0x40300000 0x80000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /*
+ * This is a placeholder for an optional reserved
+ * region for use by secure software. The size
+ * of this region is not known until runtime so it
+ * is set as zero to either be updated to reserve
+ * space or left unchanged to leave all SRAM for use.
+ * On HS parts that that require the reserved region
+ * either the bootloader can update the size to
+ * the required amount or the node can be overridden
+ * from the board dts file for the secure platform.
+ */
+ sram-hs@0 {
+ compatible = "ti,secure-ram";
+ reg = <0x0 0x0>;
+ };
+ };
+
+ /*
+ * NOTE: ocmcram2 and ocmcram3 are not available on all
+ * DRA7xx and AM57xx variants. Confirm availability in
+ * the data manual for the exact part number in use
+ * before enabling these nodes in the board dts file.
+ */
+ ocmcram2: ocmcram@40400000 {
+ status = "disabled";
+ compatible = "mmio-sram";
+ reg = <0x40400000 0x100000>;
+ ranges = <0x0 0x40400000 0x100000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ ocmcram3: ocmcram@40500000 {
+ status = "disabled";
+ compatible = "mmio-sram";
+ reg = <0x40500000 0x100000>;
+ ranges = <0x0 0x40500000 0x100000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
bandgap: bandgap@4a0021e0 {
reg = <0x4a0021e0 0xc
0x4a00232c 0xc
interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "edma3_ccint", "emda3_mperr",
+ interrupt-names = "edma3_ccint", "edma3_mperr",
"edma3_ccerrint";
dma-requests = <64>;
#dma-cells = <2>;
clock-names = "fck", "sys_clk";
};
};
+
+ epwmss0: epwmss@4843e000 {
+ compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+ reg = <0x4843e000 0x30>;
+ ti,hwmods = "epwmss0";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+ ranges;
+
+ ehrpwm0: pwm@4843e200 {
+ compatible = "ti,dra746-ehrpwm",
+ "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x4843e200 0x80>;
+ clocks = <&ehrpwm0_tbclk>, <&l4_root_clk_div>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ ecap0: ecap@4843e100 {
+ compatible = "ti,dra746-ecap",
+ "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x4843e100 0x80>;
+ clocks = <&l4_root_clk_div>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+ };
+
+ epwmss1: epwmss@48440000 {
+ compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+ reg = <0x48440000 0x30>;
+ ti,hwmods = "epwmss1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+ ranges;
+
+ ehrpwm1: pwm@48440200 {
+ compatible = "ti,dra746-ehrpwm",
+ "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x48440200 0x80>;
+ clocks = <&ehrpwm1_tbclk>, <&l4_root_clk_div>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ ecap1: ecap@48440100 {
+ compatible = "ti,dra746-ecap",
+ "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x48440100 0x80>;
+ clocks = <&l4_root_clk_div>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+ };
+
+ epwmss2: epwmss@48442000 {
+ compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+ reg = <0x48442000 0x30>;
+ ti,hwmods = "epwmss2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+ ranges;
+
+ ehrpwm2: pwm@48442200 {
+ compatible = "ti,dra746-ehrpwm",
+ "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x48442200 0x80>;
+ clocks = <&ehrpwm2_tbclk>, <&l4_root_clk_div>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ ecap2: ecap@48442100 {
+ compatible = "ti,dra746-ecap",
+ "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x48442100 0x80>;
+ clocks = <&l4_root_clk_div>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+ };
+
+ aes1: aes@4b500000 {
+ compatible = "ti,omap4-aes";
+ ti,hwmods = "aes1";
+ reg = <0x4b500000 0xa0>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma_xbar 111 0>, <&edma_xbar 110 0>;
+ dma-names = "tx", "rx";
+ clocks = <&l3_iclk_div>;
+ clock-names = "fck";
+ };
+
+ aes2: aes@4b700000 {
+ compatible = "ti,omap4-aes";
+ ti,hwmods = "aes2";
+ reg = <0x4b700000 0xa0>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma_xbar 114 0>, <&edma_xbar 113 0>;
+ dma-names = "tx", "rx";
+ clocks = <&l3_iclk_div>;
+ clock-names = "fck";
+ };
+
+ des: des@480a5000 {
+ compatible = "ti,omap4-des";
+ ti,hwmods = "des";
+ reg = <0x480a5000 0xa0>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma_xbar 117>, <&sdma_xbar 116>;
+ dma-names = "tx", "rx";
+ clocks = <&l3_iclk_div>;
+ clock-names = "fck";
+ };
+
+ sham: sham@53100000 {
+ compatible = "ti,omap5-sham";
+ ti,hwmods = "sham";
+ reg = <0x4b101000 0x300>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma_xbar 119 0>;
+ dma-names = "rx";
+ clocks = <&l3_iclk_div>;
+ clock-names = "fck";
+ };
+
+ rng: rng@48090000 {
+ compatible = "ti,omap4-rng";
+ ti,hwmods = "rng";
+ reg = <0x48090000 0x2000>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&l3_iclk_div>;
+ clock-names = "fck";
+ };
};
thermal_zones: thermal-zones {
display0 = &hdmi0;
};
- evm_3v3: fixedregulator-evm_3v3 {
+ evm_3v3_sw: fixedregulator-evm_3v3 {
compatible = "regulator-fixed";
regulator-name = "evm_3v3";
regulator-min-microvolt = <3300000>;
/* TPS77018DBVT */
compatible = "regulator-fixed";
regulator-name = "aic_dvdd";
- vin-supply = <&evm_3v3>;
+ vin-supply = <&evm_3v3_sw>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
status = "okay";
/* Regulators */
- AVDD-supply = <&evm_3v3>;
- IOVDD-supply = <&evm_3v3>;
- DRVDD-supply = <&evm_3v3>;
+ AVDD-supply = <&evm_3v3_sw>;
+ IOVDD-supply = <&evm_3v3_sw>;
+ DRVDD-supply = <&evm_3v3_sw>;
DVDD-supply = <&aic_dvdd>;
};
};
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins_default>;
- vmmc-supply = <&evm_3v3>;
+ vmmc-supply = <&evm_3v3_sw>;
bus-width = <8>;
ti,non-removable;
max-frequency = <192000000>;
/ {
compatible = "ti,dra722", "ti,dra72", "ti,dra7";
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a15";
- reg = <0>;
-
- /* cooling options */
- cooling-min-level = <0>;
- cooling-max-level = <2>;
- #cooling-cells = <2>; /* min followed by max */
- };
- };
-
pmu {
compatible = "arm,cortex-a15-pmu";
interrupt-parent = <&wakeupgen>;
compatible = "ti,dra742", "ti,dra74", "ti,dra7";
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a15";
- reg = <0>;
-
- operating-points = <
- /* kHz uV */
- 1000000 1060000
- 1176000 1160000
- >;
-
- clocks = <&dpll_mpu_ck>;
- clock-names = "cpu";
-
- clock-latency = <300000>; /* From omap-cpufreq driver */
-
- /* cooling options */
- cooling-min-level = <0>;
- cooling-max-level = <2>;
- #cooling-cells = <2>; /* min followed by max */
- };
cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <1>;
+ operating-points-v2 = <&cpu0_opp_table>;
};
};
model = "EMEV2 KZM9D Board";
compatible = "renesas,kzm9d", "renesas,emev2";
- memory {
+ memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x8000000>;
};
+ aliases {
+ serial1 = &uart1;
+ };
+
chosen {
- bootargs = "console=ttyS1,115200n81 ignore_loglevel root=/dev/nfs ip=dhcp";
- stdout-path = &uart1;
+ bootargs = "ignore_loglevel root=/dev/nfs ip=dhcp";
+ stdout-path = "serial1:115200n8";
};
gpio_keys {
#address-cells = <1>;
#size-cells = <0>;
- button@1 {
+ one {
debounce_interval = <50>;
wakeup-source;
label = "DSW2-1";
linux,code = <KEY_1>;
gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
};
- button@2 {
+ two {
debounce_interval = <50>;
wakeup-source;
label = "DSW2-2";
linux,code = <KEY_2>;
gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
};
- button@3 {
+ three {
debounce_interval = <50>;
wakeup-source;
label = "DSW2-3";
linux,code = <KEY_3>;
gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
};
- button@4 {
+ four {
debounce_interval = <50>;
wakeup-source;
label = "DSW2-4";
};
};
- reg_1p8v: regulator@0 {
+ reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-boot-on;
};
- reg_3p3v: regulator@1 {
+ reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
};
&pfc {
- uart1_pins: serial@e1030000 {
+ uart1_pins: uart1 {
groups = "uart1_ctrl", "uart1_data";
function = "uart1";
};
clock-frequency = <32768>;
#clock-cells = <0>;
};
- iic0_sclkdiv: iic0_sclkdiv {
+ iic0_sclkdiv: iic0_sclkdiv@624,0 {
compatible = "renesas,emev2-smu-clkdiv";
reg = <0x624 0>;
clocks = <&pll3_fo>;
#clock-cells = <0>;
};
- iic0_sclk: iic0_sclk {
+ iic0_sclk: iic0_sclk@48c,1 {
compatible = "renesas,emev2-smu-gclk";
reg = <0x48c 1>;
clocks = <&iic0_sclkdiv>;
#clock-cells = <0>;
};
- iic1_sclkdiv: iic1_sclkdiv {
+ iic1_sclkdiv: iic1_sclkdiv@624,16 {
compatible = "renesas,emev2-smu-clkdiv";
reg = <0x624 16>;
clocks = <&pll3_fo>;
#clock-cells = <0>;
};
- iic1_sclk: iic1_sclk {
+ iic1_sclk: iic1_sclk@490,1 {
compatible = "renesas,emev2-smu-gclk";
reg = <0x490 1>;
clocks = <&iic1_sclkdiv>;
clock-mult = <7000>;
#clock-cells = <0>;
};
- usia_u0_sclkdiv: usia_u0_sclkdiv {
+ usia_u0_sclkdiv: usia_u0_sclkdiv@610,0 {
compatible = "renesas,emev2-smu-clkdiv";
reg = <0x610 0>;
clocks = <&pll3_fo>;
#clock-cells = <0>;
};
- usib_u1_sclkdiv: usib_u1_sclkdiv {
+ usib_u1_sclkdiv: usib_u1_sclkdiv@65c,0 {
compatible = "renesas,emev2-smu-clkdiv";
reg = <0x65c 0>;
clocks = <&pll3_fo>;
#clock-cells = <0>;
};
- usib_u2_sclkdiv: usib_u2_sclkdiv {
+ usib_u2_sclkdiv: usib_u2_sclkdiv@65c,16 {
compatible = "renesas,emev2-smu-clkdiv";
reg = <0x65c 16>;
clocks = <&pll3_fo>;
#clock-cells = <0>;
};
- usib_u3_sclkdiv: usib_u3_sclkdiv {
+ usib_u3_sclkdiv: usib_u3_sclkdiv@660,0 {
compatible = "renesas,emev2-smu-clkdiv";
reg = <0x660 0>;
clocks = <&pll3_fo>;
#clock-cells = <0>;
};
- usia_u0_sclk: usia_u0_sclk {
+ usia_u0_sclk: usia_u0_sclk@4a0,1 {
compatible = "renesas,emev2-smu-gclk";
reg = <0x4a0 1>;
clocks = <&usia_u0_sclkdiv>;
#clock-cells = <0>;
};
- usib_u1_sclk: usib_u1_sclk {
+ usib_u1_sclk: usib_u1_sclk@4b8,1 {
compatible = "renesas,emev2-smu-gclk";
reg = <0x4b8 1>;
clocks = <&usib_u1_sclkdiv>;
#clock-cells = <0>;
};
- usib_u2_sclk: usib_u2_sclk {
+ usib_u2_sclk: usib_u2_sclk@4bc,1 {
compatible = "renesas,emev2-smu-gclk";
reg = <0x4bc 1>;
clocks = <&usib_u2_sclkdiv>;
#clock-cells = <0>;
};
- usib_u3_sclk: usib_u3_sclk {
+ usib_u3_sclk: usib_u3_sclk@4c0,1 {
compatible = "renesas,emev2-smu-gclk";
reg = <0x4c0 1>;
clocks = <&usib_u3_sclkdiv>;
#clock-cells = <0>;
};
- sti_sclk: sti_sclk {
+ sti_sclk: sti_sclk@528,1 {
compatible = "renesas,emev2-smu-gclk";
reg = <0x528 1>;
clocks = <&c32ki>;
--- /dev/null
+/*
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ */
+
+/dts-v1/;
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/clock/clps711x-clock.h>
+
+/ {
+ model = "Cirrus Logic EP7209";
+ compatible = "cirrus,ep7209";
+
+ aliases {
+ gpio0 = &porta;
+ gpio1 = &portb;
+ gpio3 = &portd;
+ gpio4 = &porte;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ spi0 = &spi;
+ timer0 = &timer1;
+ timer1 = &timer2;
+ };
+
+ cpus {
+ #address-cells = <0>;
+ #size-cells = <0>;
+
+ cpu {
+ device_type = "cpu";
+ compatible = "arm,arm720t";
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&intc>;
+ ranges;
+
+ clks: clks@80000000 {
+ #clock-cells = <1>;
+ compatible = "cirrus,ep7209-clk";
+ reg = <0x80000000 0xc000>;
+ startup-frequency = <73728000>;
+ };
+
+ intc: intc@80000000 {
+ compatible = "cirrus,ep7209-intc";
+ reg = <0x80000000 0x4000>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ porta: gpio@80000000 {
+ compatible = "cirrus,ep7209-gpio";
+ reg = <0x80000000 0x1 0x80000040 0x1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ portb: gpio@80000001 {
+ compatible = "cirrus,ep7209-gpio";
+ reg = <0x80000001 0x1 0x80000041 0x1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ portd: gpio@80000003 {
+ compatible = "cirrus,ep7209-gpio";
+ reg = <0x80000003 0x1 0x80000043 0x1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ porte: gpio@80000083 {
+ compatible = "cirrus,ep7209-gpio";
+ reg = <0x80000083 0x1 0x800000c3 0x1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ syscon1: syscon@80000100 {
+ compatible = "cirrus,ep7209-syscon1", "syscon";
+ reg = <0x80000100 0x80>;
+ };
+
+ bus: bus@80000180 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "cirrus,ep7209-bus", "simple-bus";
+ clocks = <&clks CLPS711X_CLK_BUS>;
+ reg = <0x80000180 0x80>;
+ ranges = <
+ 0 0 0x00000000 0x10000000
+ 1 0 0x10000000 0x10000000
+ 2 0 0x20000000 0x10000000
+ 3 0 0x30000000 0x10000000
+ 4 0 0x40000000 0x10000000
+ 5 0 0x50000000 0x10000000
+ 6 0 0x60000000 0x0000c000
+ 7 0 0x70000000 0x00000080
+ >;
+ };
+
+ fb: fb@800002c0 {
+ compatible = "cirrus,ep7209-fb";
+ reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
+ clocks = <&clks CLPS711X_CLK_BUS>;
+ status = "disabled";
+ };
+
+ timer1: timer@80000300 {
+ compatible = "cirrus,ep7209-timer";
+ reg = <0x80000300 0x4>;
+ clocks = <&clks CLPS711X_CLK_TIMER1>;
+ interrupts = <8>;
+ };
+
+ timer2: timer@80000340 {
+ compatible = "cirrus,ep7209-timer";
+ reg = <0x80000340 0x4>;
+ clocks = <&clks CLPS711X_CLK_TIMER2>;
+ interrupts = <9>;
+ };
+
+ pwm: pwm@80000400 {
+ compatible = "cirrus,ep7209-pwm";
+ reg = <0x80000400 0x4>;
+ clocks = <&clks CLPS711X_CLK_PWM>;
+ #pwm-cells = <1>;
+ };
+
+ uart1: uart@80000480 {
+ compatible = "cirrus,ep7209-uart";
+ reg = <0x80000480 0x80>;
+ interrupts = <12 13>;
+ clocks = <&clks CLPS711X_CLK_UART>;
+ syscon = <&syscon1>;
+ };
+
+ spi: spi@80000500 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cirrus,ep7209-spi";
+ reg = <0x80000500 0x4>;
+ interrupts = <15>;
+ clocks = <&clks CLPS711X_CLK_SPI>;
+ status = "disabled";
+ };
+
+ syscon2: syscon@80001100 {
+ compatible = "cirrus,ep7209-syscon2", "syscon";
+ reg = <0x80001100 0x80>;
+ };
+
+ uart2: uart@80001480 {
+ compatible = "cirrus,ep7209-uart";
+ reg = <0x80001480 0x80>;
+ interrupts = <28 29>;
+ clocks = <&clks CLPS711X_CLK_UART>;
+ syscon = <&syscon2>;
+ };
+
+ dai: dai@80002000 {
+ #sound-dai-cells = <0>;
+ compatible = "cirrus,ep7209-dai";
+ reg = <0x80002000 0x604>;
+ clocks = <&clks CLPS711X_CLK_PLL>;
+ clock-names = "pll";
+ interrupts = <32>;
+ status = "disabled";
+ };
+
+ syscon3: syscon@80002200 {
+ compatible = "cirrus,ep7209-syscon3", "syscon";
+ reg = <0x80002200 0x40>;
+ };
+ };
+
+ mctrl: mctrl {
+ compatible = "cirrus,ep7209-mctrl-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
--- /dev/null
+/*
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ */
+
+#include "ep7211.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Cirrus Logic EP7211 Development Board";
+ compatible = "cirrus,edb7211", "cirrus,ep7211", "cirrus,ep7209";
+
+ memory {
+ reg = <0xc0000000 0x02000000>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0>;
+ brightness-levels = <
+ 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7
+ 0x8 0x9 0xa 0xb 0xc 0xd 0xe 0xf
+ >;
+ default-brightness-level = <0x0>;
+ power-supply = <&blen>;
+ };
+
+ display: display {
+ model = "320x240x4";
+ native-mode = <&timing0>;
+ bits-per-pixel = <4>;
+ ac-prescale = <17>;
+
+ display-timings {
+ timing0: 320x240 {
+ hactive = <320>;
+ hback-porch = <0>;
+ hfront-porch = <0>;
+ hsync-len = <0>;
+ vactive = <240>;
+ vback-porch = <0>;
+ vfront-porch = <0>;
+ vsync-len = <0>;
+ clock-frequency = <6500000>;
+ };
+ };
+ };
+
+ i2c: i2c {
+ compatible = "i2c-gpio";
+ gpios = <&portd 4 GPIO_ACTIVE_HIGH>,
+ <&portd 5 GPIO_ACTIVE_HIGH>;
+ i2c-gpio,delay-us = <2>;
+ i2c-gpio,scl-output-only;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ lcddc: lcddc {
+ compatible = "regulator-fixed";
+ regulator-name = "BACKLIGHT ENABLE";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&portd 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ blen: blen {
+ compatible = "regulator-fixed";
+ regulator-name = "BACKLIGHT ENABLE";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&portd 3 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&bus {
+ flash: nor@00000000 {
+ compatible = "cfi-flash";
+ reg = <0 0x00000000 0x02000000>;
+ bank-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&fb {
+ display = <&display>;
+ lcd-supply = <&lcddc>;
+ status = "okay";
+};
+
+&portd {
+ lcden {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LCD ENABLE";
+ };
+};
--- /dev/null
+/*
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ */
+
+#include "ep7209.dtsi"
+
+/ {
+ model = "Cirrus Logic EP7211";
+ compatible = "cirrus,ep7211", "cirrus,ep7209";
+};
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
pcf8563@50 {
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
};
#size-cells = <1>;
ranges;
- mfc_left: region@51000000 {
+ mfc_left: region_mfc_left {
compatible = "shared-dma-pool";
no-map;
- reg = <0x51000000 0x800000>;
+ size = <0x1000000>;
+ alignment = <0x100000>;
};
- mfc_right: region@43000000 {
+ mfc_right: region_mfc_right {
compatible = "shared-dma-pool";
no-map;
- reg = <0x43000000 0x800000>;
+ size = <0x800000>;
+ alignment = <0x100000>;
};
};
};
+
+&mfc {
+ memory-region = <&mfc_left>, <&mfc_right>;
+};
status = "okay";
};
-&mfc {
- status = "okay";
-};
-
&jpeg {
status = "okay";
};
clocks = <&cmu CLK_MFC>, <&cmu CLK_SCLK_MFC>;
power-domains = <&pd_mfc>;
iommus = <&sysmmu_mfc>;
- status = "disabled";
};
sysmmu_mfc: sysmmu@13620000 {
clock-names = "mfc", "sclk_mfc";
iommus = <&sysmmu_mfc_l>, <&sysmmu_mfc_r>;
iommu-names = "left", "right";
- status = "disabled";
};
serial_0: serial@13800000 {
};
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
- status = "okay";
-};
-
&sdhci_0 {
bus-width = <4>;
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
};
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
- status = "okay";
-};
-
&pinctrl_1 {
keypad_rows: keypad-rows {
samsung,pins = "gpx2-0", "gpx2-1";
regulator-name = "VDDQ_MMC2_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- regulator-always-on;
regulator-boot-on;
};
};
ldo21_reg: LDO21 {
- regulator-name = "LDO21_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
+ regulator-name = "TFLASH_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-boot-on;
+ };
+
+ ldo22_reg: LDO22 {
+ /*
+ * Only U3 uses it, so let it define the
+ * constraints
+ */
+ regulator-name = "LDO22";
regulator-boot-on;
};
};
buck8_reg: BUCK8 {
+ /*
+ * Constraints set by specific board: X,
+ * X2 and U3.
+ */
regulator-name = "BUCK8_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
};
};
};
clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
- status = "okay";
-};
-
&mixer {
status = "okay";
};
&mshc_0 {
pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
pinctrl-names = "default";
- vmmc-supply = <&ldo20_reg &buck8_reg>;
+ vmmc-supply = <&ldo20_reg>;
mmc-pwrseq = <&emmc_pwrseq>;
status = "okay";
bus-width = <4>;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
pinctrl-names = "default";
- vmmc-supply = <&ldo4_reg &ldo21_reg>;
+ vmmc-supply = <&ldo21_reg>;
+ vqmmc-supply = <&ldo4_reg>;
cd-gpios = <&gpk2 2 GPIO_ACTIVE_HIGH>;
cd-inverted;
status = "okay";
};
};
+/* Supply for LAN9730/SMSC95xx */
+&buck8_reg {
+ regulator-name = "BUCK8_P3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+};
+
+/* VDDQ for MSHC (eMMC card) */
+&ldo22_reg {
+ regulator-name = "LDO22_VDDQ_MMC4_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
+
+&mshc_0 {
+ vqmmc-supply = <&ldo22_reg>;
+};
+
&pwm {
pinctrl-0 = <&pwm0_out>;
pinctrl-names = "default";
};
};
+/* VDDQ for MSHC (eMMC card) */
+&buck8_reg {
+ regulator-name = "BUCK8_VDDQ_MMC4_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
+
&ehci {
port@1 {
status = "okay";
};
};
+&mshc_0 {
+ vqmmc-supply = <&buck8_reg>;
+};
+
&pinctrl_1 {
gpio_home_key: home_key {
samsung,pins = "gpx2-2";
};
};
+/* VDDQ for MSHC (eMMC card) */
+&buck8_reg {
+ regulator-name = "BUCK8_VDDQ_MMC4_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
+
+&mshc_0 {
+ vqmmc-supply = <&buck8_reg>;
+};
+
&sound {
simple-audio-card,name = "Odroid-X2";
simple-audio-card,widgets =
cpu0-supply = <&buck2_reg>;
};
+&exynos_usbphy {
+ status = "okay";
+};
+
+&ehci {
+ samsung,vbus-gpio = <&gpx3 5 1>;
+ status = "okay";
+
+ port@1{
+ status = "okay";
+ };
+ port@2 {
+ status = "okay";
+ };
+};
+
&fimd {
pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
pinctrl-names = "default";
};
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
- status = "okay";
-};
-
&mshc_0 {
pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
pinctrl-names = "default";
};
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
- status = "okay";
-};
-
&pinctrl_1 {
keypad_rows: keypad-rows {
samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
};
thermistor-ap {
- compatible = "ntc,ncp15wb473";
+ compatible = "murata,ncp15wb473";
pullup-uv = <1800000>; /* VCC_1.8V_AP */
pullup-ohm = <100000>; /* 100K */
pulldown-ohm = <100000>; /* 100K */
};
thermistor-battery {
- compatible = "ntc,ncp15wb473";
+ compatible = "murata,ncp15wb473";
pullup-uv = <1800000>; /* VCC_1.8V_AP */
pullup-ohm = <100000>; /* 100K */
pulldown-ohm = <100000>; /* 100K */
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c_0;
+ i2c1 = &i2c_1;
+ i2c2 = &i2c_2;
+ i2c3 = &i2c_3;
serial0 = &serial_0;
serial1 = &serial_1;
serial2 = &serial_2;
serial3 = &serial_3;
};
- chipid@10000000 {
- compatible = "samsung,exynos4210-chipid";
- reg = <0x10000000 0x100>;
- };
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
- memory-controller@12250000 {
- compatible = "samsung,exynos4210-srom";
- reg = <0x12250000 0x14>;
- };
+ chipid@10000000 {
+ compatible = "samsung,exynos4210-chipid";
+ reg = <0x10000000 0x100>;
+ };
- combiner: interrupt-controller@10440000 {
- compatible = "samsung,exynos4210-combiner";
- #interrupt-cells = <2>;
- interrupt-controller;
- samsung,combiner-nr = <32>;
- reg = <0x10440000 0x1000>;
- interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
- <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
- <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
- <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
- <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
- <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
- <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
- <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>;
- };
+ sromc: memory-controller@12250000 {
+ compatible = "samsung,exynos4210-srom";
+ reg = <0x12250000 0x14>;
+ };
- gic: interrupt-controller@10481000 {
- compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
- #interrupt-cells = <3>;
- interrupt-controller;
- reg = <0x10481000 0x1000>,
- <0x10482000 0x1000>,
- <0x10484000 0x2000>,
- <0x10486000 0x2000>;
- interrupts = <1 9 0xf04>;
- };
+ combiner: interrupt-controller@10440000 {
+ compatible = "samsung,exynos4210-combiner";
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ samsung,combiner-nr = <32>;
+ reg = <0x10440000 0x1000>;
+ interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+ <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+ <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+ <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+ <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+ <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+ <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+ <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>;
+ };
- serial_0: serial@12C00000 {
- compatible = "samsung,exynos4210-uart";
- reg = <0x12C00000 0x100>;
- interrupts = <0 51 0>;
- };
+ gic: interrupt-controller@10481000 {
+ compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x10481000 0x1000>,
+ <0x10482000 0x1000>,
+ <0x10484000 0x2000>,
+ <0x10486000 0x2000>;
+ interrupts = <1 9 0xf04>;
+ };
- serial_1: serial@12C10000 {
- compatible = "samsung,exynos4210-uart";
- reg = <0x12C10000 0x100>;
- interrupts = <0 52 0>;
- };
+ sysreg_system_controller: syscon@10050000 {
+ compatible = "samsung,exynos5-sysreg", "syscon";
+ reg = <0x10050000 0x5000>;
+ };
- serial_2: serial@12C20000 {
- compatible = "samsung,exynos4210-uart";
- reg = <0x12C20000 0x100>;
- interrupts = <0 53 0>;
- };
+ serial_0: serial@12C00000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x12C00000 0x100>;
+ interrupts = <0 51 0>;
+ };
- serial_3: serial@12C30000 {
- compatible = "samsung,exynos4210-uart";
- reg = <0x12C30000 0x100>;
- interrupts = <0 54 0>;
- };
+ serial_1: serial@12C10000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x12C10000 0x100>;
+ interrupts = <0 52 0>;
+ };
- rtc: rtc@101E0000 {
- compatible = "samsung,s3c6410-rtc";
- reg = <0x101E0000 0x100>;
- interrupts = <0 43 0>, <0 44 0>;
- status = "disabled";
- };
+ serial_2: serial@12C20000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x12C20000 0x100>;
+ interrupts = <0 53 0>;
+ };
- fimd: fimd@14400000 {
- compatible = "samsung,exynos5250-fimd";
- interrupt-parent = <&combiner>;
- reg = <0x14400000 0x40000>;
- interrupt-names = "fifo", "vsync", "lcd_sys";
- interrupts = <18 4>, <18 5>, <18 6>;
- samsung,sysreg = <&sysreg_system_controller>;
- status = "disabled";
- };
+ serial_3: serial@12C30000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x12C30000 0x100>;
+ interrupts = <0 54 0>;
+ };
- dp: dp-controller@145B0000 {
- compatible = "samsung,exynos5-dp";
- reg = <0x145B0000 0x1000>;
- interrupts = <10 3>;
- interrupt-parent = <&combiner>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
+ i2c_0: i2c@12C60000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C60000 0x100>;
+ interrupts = <0 56 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ status = "disabled";
+ };
+
+ i2c_1: i2c@12C70000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C70000 0x100>;
+ interrupts = <0 57 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ status = "disabled";
+ };
+
+ i2c_2: i2c@12C80000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C80000 0x100>;
+ interrupts = <0 58 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ status = "disabled";
+ };
+
+ i2c_3: i2c@12C90000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C90000 0x100>;
+ interrupts = <0 59 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ status = "disabled";
+ };
+
+ pwm: pwm@12DD0000 {
+ compatible = "samsung,exynos4210-pwm";
+ reg = <0x12DD0000 0x100>;
+ samsung,pwm-outputs = <0>, <1>, <2>, <3>;
+ #pwm-cells = <3>;
+ };
+
+ rtc: rtc@101E0000 {
+ compatible = "samsung,s3c6410-rtc";
+ reg = <0x101E0000 0x100>;
+ interrupts = <0 43 0>, <0 44 0>;
+ status = "disabled";
+ };
+
+ fimd: fimd@14400000 {
+ compatible = "samsung,exynos5250-fimd";
+ interrupt-parent = <&combiner>;
+ reg = <0x14400000 0x40000>;
+ interrupt-names = "fifo", "vsync", "lcd_sys";
+ interrupts = <18 4>, <18 5>, <18 6>;
+ samsung,sysreg = <&sysreg_system_controller>;
+ status = "disabled";
+ };
+
+ dp: dp-controller@145B0000 {
+ compatible = "samsung,exynos5-dp";
+ reg = <0x145B0000 0x1000>;
+ interrupts = <10 3>;
+ interrupt-parent = <&combiner>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};
};
status = "okay";
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
num-slots = <1>;
status = "okay";
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
num-slots = <1>;
#address-cells = <1>;
#size-cells = <0>;
- i2c-parent = <&{/i2c@12CA0000}>;
+ i2c-parent = <&i2c_4>;
our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>;
their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
status = "okay";
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
num-slots = <1>;
mshc1 = &mmc_1;
mshc2 = &mmc_2;
mshc3 = &mmc_3;
- i2c0 = &i2c_0;
- i2c1 = &i2c_1;
- i2c2 = &i2c_2;
- i2c3 = &i2c_3;
i2c4 = &i2c_4;
i2c5 = &i2c_5;
i2c6 = &i2c_6;
};
};
- sysram@02020000 {
- compatible = "mmio-sram";
- reg = <0x02020000 0x30000>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0x02020000 0x30000>;
+ soc: soc {
+ sysram@02020000 {
+ compatible = "mmio-sram";
+ reg = <0x02020000 0x30000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x02020000 0x30000>;
- smp-sysram@0 {
- compatible = "samsung,exynos4210-sysram";
- reg = <0x0 0x1000>;
- };
+ smp-sysram@0 {
+ compatible = "samsung,exynos4210-sysram";
+ reg = <0x0 0x1000>;
+ };
- smp-sysram@2f000 {
- compatible = "samsung,exynos4210-sysram-ns";
- reg = <0x2f000 0x1000>;
+ smp-sysram@2f000 {
+ compatible = "samsung,exynos4210-sysram-ns";
+ reg = <0x2f000 0x1000>;
+ };
};
- };
- pd_gsc: gsc-power-domain@10044000 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x10044000 0x20>;
- #power-domain-cells = <0>;
- };
+ pd_gsc: gsc-power-domain@10044000 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10044000 0x20>;
+ #power-domain-cells = <0>;
+ };
- pd_mfc: mfc-power-domain@10044040 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x10044040 0x20>;
- #power-domain-cells = <0>;
- };
+ pd_mfc: mfc-power-domain@10044040 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10044040 0x20>;
+ #power-domain-cells = <0>;
+ };
- pd_disp1: disp1-power-domain@100440A0 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x100440A0 0x20>;
- #power-domain-cells = <0>;
- clocks = <&clock CLK_FIN_PLL>,
- <&clock CLK_MOUT_ACLK200_DISP1_SUB>,
- <&clock CLK_MOUT_ACLK300_DISP1_SUB>;
- clock-names = "oscclk", "clk0", "clk1";
- };
+ pd_disp1: disp1-power-domain@100440A0 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x100440A0 0x20>;
+ #power-domain-cells = <0>;
+ clocks = <&clock CLK_FIN_PLL>,
+ <&clock CLK_MOUT_ACLK200_DISP1_SUB>,
+ <&clock CLK_MOUT_ACLK300_DISP1_SUB>;
+ clock-names = "oscclk", "clk0", "clk1";
+ };
- clock: clock-controller@10010000 {
- compatible = "samsung,exynos5250-clock";
- reg = <0x10010000 0x30000>;
- #clock-cells = <1>;
- };
+ clock: clock-controller@10010000 {
+ compatible = "samsung,exynos5250-clock";
+ reg = <0x10010000 0x30000>;
+ #clock-cells = <1>;
+ };
- clock_audss: audss-clock-controller@3810000 {
- compatible = "samsung,exynos5250-audss-clock";
- reg = <0x03810000 0x0C>;
- #clock-cells = <1>;
- clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
- <&clock CLK_SCLK_AUDIO0>, <&clock CLK_DIV_PCM0>;
- clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
- };
+ clock_audss: audss-clock-controller@3810000 {
+ compatible = "samsung,exynos5250-audss-clock";
+ reg = <0x03810000 0x0C>;
+ #clock-cells = <1>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
+ <&clock CLK_SCLK_AUDIO0>, <&clock CLK_DIV_PCM0>;
+ clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
+ };
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <1 13 0xf08>,
- <1 14 0xf08>,
- <1 11 0xf08>,
- <1 10 0xf08>;
- /* Unfortunately we need this since some versions of U-Boot
- * on Exynos don't set the CNTFRQ register, so we need the
- * value from DT.
- */
- clock-frequency = <24000000>;
- };
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <1 13 0xf08>,
+ <1 14 0xf08>,
+ <1 11 0xf08>,
+ <1 10 0xf08>;
+ /*
+ * Unfortunately we need this since some versions
+ * of U-Boot on Exynos don't set the CNTFRQ register,
+ * so we need the value from DT.
+ */
+ clock-frequency = <24000000>;
+ };
- mct@101C0000 {
- compatible = "samsung,exynos4210-mct";
- reg = <0x101C0000 0x800>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupt-parent = <&mct_map>;
- interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
- <4 0>, <5 0>;
- clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
- clock-names = "fin_pll", "mct";
-
- mct_map: mct-map {
+ mct@101C0000 {
+ compatible = "samsung,exynos4210-mct";
+ reg = <0x101C0000 0x800>;
+ interrupt-controller;
#interrupt-cells = <2>;
- #address-cells = <0>;
- #size-cells = <0>;
- interrupt-map = <0x0 0 &combiner 23 3>,
- <0x1 0 &combiner 23 4>,
- <0x2 0 &combiner 25 2>,
- <0x3 0 &combiner 25 3>,
- <0x4 0 &gic 0 120 0>,
- <0x5 0 &gic 0 121 0>;
+ interrupt-parent = <&mct_map>;
+ interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
+ <4 0>, <5 0>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
+ clock-names = "fin_pll", "mct";
+
+ mct_map: mct-map {
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = <0x0 0 &combiner 23 3>,
+ <0x1 0 &combiner 23 4>,
+ <0x2 0 &combiner 25 2>,
+ <0x3 0 &combiner 25 3>,
+ <0x4 0 &gic 0 120 0>,
+ <0x5 0 &gic 0 121 0>;
+ };
};
- };
-
- pmu {
- compatible = "arm,cortex-a15-pmu";
- interrupt-parent = <&combiner>;
- interrupts = <1 2>, <22 4>;
- };
-
- pinctrl_0: pinctrl@11400000 {
- compatible = "samsung,exynos5250-pinctrl";
- reg = <0x11400000 0x1000>;
- interrupts = <0 46 0>;
- wakup_eint: wakeup-interrupt-controller {
- compatible = "samsung,exynos4210-wakeup-eint";
- interrupt-parent = <&gic>;
- interrupts = <0 32 0>;
+ pmu {
+ compatible = "arm,cortex-a15-pmu";
+ interrupt-parent = <&combiner>;
+ interrupts = <1 2>, <22 4>;
};
- };
-
- pinctrl_1: pinctrl@13400000 {
- compatible = "samsung,exynos5250-pinctrl";
- reg = <0x13400000 0x1000>;
- interrupts = <0 45 0>;
- };
- pinctrl_2: pinctrl@10d10000 {
- compatible = "samsung,exynos5250-pinctrl";
- reg = <0x10d10000 0x1000>;
- interrupts = <0 50 0>;
- };
-
- pinctrl_3: pinctrl@03860000 {
- compatible = "samsung,exynos5250-pinctrl";
- reg = <0x03860000 0x1000>;
- interrupts = <0 47 0>;
- };
-
- pmu_system_controller: system-controller@10040000 {
- compatible = "samsung,exynos5250-pmu", "syscon";
- reg = <0x10040000 0x5000>;
- clock-names = "clkout16";
- clocks = <&clock CLK_FIN_PLL>;
- #clock-cells = <1>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupt-parent = <&gic>;
- };
+ pinctrl_0: pinctrl@11400000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x11400000 0x1000>;
+ interrupts = <0 46 0>;
- sysreg_system_controller: syscon@10050000 {
- compatible = "samsung,exynos5-sysreg", "syscon";
- reg = <0x10050000 0x5000>;
- };
+ wakup_eint: wakeup-interrupt-controller {
+ compatible = "samsung,exynos4210-wakeup-eint";
+ interrupt-parent = <&gic>;
+ interrupts = <0 32 0>;
+ };
+ };
- watchdog@101D0000 {
- compatible = "samsung,exynos5250-wdt";
- reg = <0x101D0000 0x100>;
- interrupts = <0 42 0>;
- clocks = <&clock CLK_WDT>;
- clock-names = "watchdog";
- samsung,syscon-phandle = <&pmu_system_controller>;
- };
+ pinctrl_1: pinctrl@13400000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x13400000 0x1000>;
+ interrupts = <0 45 0>;
+ };
- g2d@10850000 {
- compatible = "samsung,exynos5250-g2d";
- reg = <0x10850000 0x1000>;
- interrupts = <0 91 0>;
- clocks = <&clock CLK_G2D>;
- clock-names = "fimg2d";
- iommus = <&sysmmu_g2d>;
- };
+ pinctrl_2: pinctrl@10d10000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x10d10000 0x1000>;
+ interrupts = <0 50 0>;
+ };
- mfc: codec@11000000 {
- compatible = "samsung,mfc-v6";
- reg = <0x11000000 0x10000>;
- interrupts = <0 96 0>;
- power-domains = <&pd_mfc>;
- clocks = <&clock CLK_MFC>;
- clock-names = "mfc";
- iommus = <&sysmmu_mfc_l>, <&sysmmu_mfc_r>;
- iommu-names = "left", "right";
- };
+ pinctrl_3: pinctrl@03860000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x03860000 0x1000>;
+ interrupts = <0 47 0>;
+ };
- rotator: rotator@11C00000 {
- compatible = "samsung,exynos5250-rotator";
- reg = <0x11C00000 0x64>;
- interrupts = <0 84 0>;
- clocks = <&clock CLK_ROTATOR>;
- clock-names = "rotator";
- iommus = <&sysmmu_rotator>;
- };
+ pmu_system_controller: system-controller@10040000 {
+ compatible = "samsung,exynos5250-pmu", "syscon";
+ reg = <0x10040000 0x5000>;
+ clock-names = "clkout16";
+ clocks = <&clock CLK_FIN_PLL>;
+ #clock-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ };
- tmu: tmu@10060000 {
- compatible = "samsung,exynos5250-tmu";
- reg = <0x10060000 0x100>;
- interrupts = <0 65 0>;
- clocks = <&clock CLK_TMU>;
- clock-names = "tmu_apbif";
- #include "exynos4412-tmu-sensor-conf.dtsi"
- };
+ watchdog@101D0000 {
+ compatible = "samsung,exynos5250-wdt";
+ reg = <0x101D0000 0x100>;
+ interrupts = <0 42 0>;
+ clocks = <&clock CLK_WDT>;
+ clock-names = "watchdog";
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ };
- thermal-zones {
- cpu_thermal: cpu-thermal {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tmu 0>;
+ g2d@10850000 {
+ compatible = "samsung,exynos5250-g2d";
+ reg = <0x10850000 0x1000>;
+ interrupts = <0 91 0>;
+ clocks = <&clock CLK_G2D>;
+ clock-names = "fimg2d";
+ iommus = <&sysmmu_g2d>;
+ };
- cooling-maps {
- map0 {
- /* Corresponds to 800MHz at freq_table */
- cooling-device = <&cpu0 9 9>;
- };
- map1 {
- /* Corresponds to 200MHz at freq_table */
- cooling-device = <&cpu0 15 15>;
- };
- };
+ mfc: codec@11000000 {
+ compatible = "samsung,mfc-v6";
+ reg = <0x11000000 0x10000>;
+ interrupts = <0 96 0>;
+ power-domains = <&pd_mfc>;
+ clocks = <&clock CLK_MFC>;
+ clock-names = "mfc";
+ iommus = <&sysmmu_mfc_l>, <&sysmmu_mfc_r>;
+ iommu-names = "left", "right";
};
- };
- sata: sata@122F0000 {
- compatible = "snps,dwc-ahci";
- samsung,sata-freq = <66>;
- reg = <0x122F0000 0x1ff>;
- interrupts = <0 115 0>;
- clocks = <&clock CLK_SATA>, <&clock CLK_SCLK_SATA>;
- clock-names = "sata", "sclk_sata";
- phys = <&sata_phy>;
- phy-names = "sata-phy";
- status = "disabled";
- };
+ rotator: rotator@11C00000 {
+ compatible = "samsung,exynos5250-rotator";
+ reg = <0x11C00000 0x64>;
+ interrupts = <0 84 0>;
+ clocks = <&clock CLK_ROTATOR>;
+ clock-names = "rotator";
+ iommus = <&sysmmu_rotator>;
+ };
- sata_phy: sata-phy@12170000 {
- compatible = "samsung,exynos5250-sata-phy";
- reg = <0x12170000 0x1ff>;
- clocks = <&clock CLK_SATA_PHYCTRL>;
- clock-names = "sata_phyctrl";
- #phy-cells = <0>;
- samsung,syscon-phandle = <&pmu_system_controller>;
- status = "disabled";
- };
+ tmu: tmu@10060000 {
+ compatible = "samsung,exynos5250-tmu";
+ reg = <0x10060000 0x100>;
+ interrupts = <0 65 0>;
+ clocks = <&clock CLK_TMU>;
+ clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
- i2c_0: i2c@12C60000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C60000 0x100>;
- interrupts = <0 56 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C0>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
+ sata: sata@122F0000 {
+ compatible = "snps,dwc-ahci";
+ samsung,sata-freq = <66>;
+ reg = <0x122F0000 0x1ff>;
+ interrupts = <0 115 0>;
+ clocks = <&clock CLK_SATA>, <&clock CLK_SCLK_SATA>;
+ clock-names = "sata", "sclk_sata";
+ phys = <&sata_phy>;
+ phy-names = "sata-phy";
+ status = "disabled";
+ };
- i2c_1: i2c@12C70000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C70000 0x100>;
- interrupts = <0 57 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C1>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
+ sata_phy: sata-phy@12170000 {
+ compatible = "samsung,exynos5250-sata-phy";
+ reg = <0x12170000 0x1ff>;
+ clocks = <&clock CLK_SATA_PHYCTRL>;
+ clock-names = "sata_phyctrl";
+ #phy-cells = <0>;
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ status = "disabled";
+ };
- i2c_2: i2c@12C80000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C80000 0x100>;
- interrupts = <0 58 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C2>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
+ /* i2c_0-3 are defined in exynos5.dtsi */
+ i2c_4: i2c@12CA0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CA0000 0x100>;
+ interrupts = <0 60 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_I2C4>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_bus>;
+ status = "disabled";
+ };
- i2c_3: i2c@12C90000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C90000 0x100>;
- interrupts = <0 59 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C3>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
+ i2c_5: i2c@12CB0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CB0000 0x100>;
+ interrupts = <0 61 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_I2C5>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_bus>;
+ status = "disabled";
+ };
- i2c_4: i2c@12CA0000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12CA0000 0x100>;
- interrupts = <0 60 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C4>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_bus>;
- status = "disabled";
- };
+ i2c_6: i2c@12CC0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CC0000 0x100>;
+ interrupts = <0 62 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_I2C6>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_bus>;
+ status = "disabled";
+ };
- i2c_5: i2c@12CB0000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12CB0000 0x100>;
- interrupts = <0 61 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C5>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_bus>;
- status = "disabled";
- };
+ i2c_7: i2c@12CD0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CD0000 0x100>;
+ interrupts = <0 63 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_I2C7>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_bus>;
+ status = "disabled";
+ };
- i2c_6: i2c@12CC0000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12CC0000 0x100>;
- interrupts = <0 62 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C6>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c6_bus>;
- status = "disabled";
- };
+ i2c_8: i2c@12CE0000 {
+ compatible = "samsung,s3c2440-hdmiphy-i2c";
+ reg = <0x12CE0000 0x1000>;
+ interrupts = <0 64 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_I2C_HDMI>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
- i2c_7: i2c@12CD0000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12CD0000 0x100>;
- interrupts = <0 63 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C7>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c7_bus>;
- status = "disabled";
- };
+ i2c_9: i2c@121D0000 {
+ compatible = "samsung,exynos5-sata-phy-i2c";
+ reg = <0x121D0000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_SATA_PHYI2C>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
- i2c_8: i2c@12CE0000 {
- compatible = "samsung,s3c2440-hdmiphy-i2c";
- reg = <0x12CE0000 0x1000>;
- interrupts = <0 64 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C_HDMI>;
- clock-names = "i2c";
- status = "disabled";
- };
+ spi_0: spi@12d20000 {
+ compatible = "samsung,exynos4210-spi";
+ status = "disabled";
+ reg = <0x12d20000 0x100>;
+ interrupts = <0 66 0>;
+ dmas = <&pdma0 5
+ &pdma0 4>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
+ clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_bus>;
+ };
- i2c_9: i2c@121D0000 {
- compatible = "samsung,exynos5-sata-phy-i2c";
- reg = <0x121D0000 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_SATA_PHYI2C>;
- clock-names = "i2c";
- status = "disabled";
- };
+ spi_1: spi@12d30000 {
+ compatible = "samsung,exynos4210-spi";
+ status = "disabled";
+ reg = <0x12d30000 0x100>;
+ interrupts = <0 67 0>;
+ dmas = <&pdma1 5
+ &pdma1 4>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
+ clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ };
- spi_0: spi@12d20000 {
- compatible = "samsung,exynos4210-spi";
- status = "disabled";
- reg = <0x12d20000 0x100>;
- interrupts = <0 66 0>;
- dmas = <&pdma0 5
- &pdma0 4>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
- clock-names = "spi", "spi_busclk0";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_bus>;
- };
+ spi_2: spi@12d40000 {
+ compatible = "samsung,exynos4210-spi";
+ status = "disabled";
+ reg = <0x12d40000 0x100>;
+ interrupts = <0 68 0>;
+ dmas = <&pdma0 7
+ &pdma0 6>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
+ clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_bus>;
+ };
- spi_1: spi@12d30000 {
- compatible = "samsung,exynos4210-spi";
- status = "disabled";
- reg = <0x12d30000 0x100>;
- interrupts = <0 67 0>;
- dmas = <&pdma1 5
- &pdma1 4>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
- clock-names = "spi", "spi_busclk0";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_bus>;
- };
+ mmc_0: mmc@12200000 {
+ compatible = "samsung,exynos5250-dw-mshc";
+ interrupts = <0 75 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x12200000 0x1000>;
+ clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ status = "disabled";
+ };
- spi_2: spi@12d40000 {
- compatible = "samsung,exynos4210-spi";
- status = "disabled";
- reg = <0x12d40000 0x100>;
- interrupts = <0 68 0>;
- dmas = <&pdma0 7
- &pdma0 6>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
- clock-names = "spi", "spi_busclk0";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_bus>;
- };
+ mmc_1: mmc@12210000 {
+ compatible = "samsung,exynos5250-dw-mshc";
+ interrupts = <0 76 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x12210000 0x1000>;
+ clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ status = "disabled";
+ };
- mmc_0: mmc@12200000 {
- compatible = "samsung,exynos5250-dw-mshc";
- interrupts = <0 75 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x12200000 0x1000>;
- clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>;
- clock-names = "biu", "ciu";
- fifo-depth = <0x80>;
- status = "disabled";
- };
+ mmc_2: mmc@12220000 {
+ compatible = "samsung,exynos5250-dw-mshc";
+ interrupts = <0 77 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x12220000 0x1000>;
+ clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ status = "disabled";
+ };
- mmc_1: mmc@12210000 {
- compatible = "samsung,exynos5250-dw-mshc";
- interrupts = <0 76 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x12210000 0x1000>;
- clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>;
- clock-names = "biu", "ciu";
- fifo-depth = <0x80>;
- status = "disabled";
- };
+ mmc_3: mmc@12230000 {
+ compatible = "samsung,exynos5250-dw-mshc";
+ reg = <0x12230000 0x1000>;
+ interrupts = <0 78 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ status = "disabled";
+ };
- mmc_2: mmc@12220000 {
- compatible = "samsung,exynos5250-dw-mshc";
- interrupts = <0 77 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x12220000 0x1000>;
- clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>;
- clock-names = "biu", "ciu";
- fifo-depth = <0x80>;
- status = "disabled";
- };
+ i2s0: i2s@03830000 {
+ compatible = "samsung,s5pv210-i2s";
+ status = "disabled";
+ reg = <0x03830000 0x100>;
+ dmas = <&pdma0 10
+ &pdma0 9
+ &pdma0 8>;
+ dma-names = "tx", "rx", "tx-sec";
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+ samsung,idma-addr = <0x03000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_bus>;
+ };
- mmc_3: mmc@12230000 {
- compatible = "samsung,exynos5250-dw-mshc";
- reg = <0x12230000 0x1000>;
- interrupts = <0 78 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>;
- clock-names = "biu", "ciu";
- fifo-depth = <0x80>;
- status = "disabled";
- };
+ i2s1: i2s@12D60000 {
+ compatible = "samsung,s3c6410-i2s";
+ status = "disabled";
+ reg = <0x12D60000 0x100>;
+ dmas = <&pdma1 12
+ &pdma1 11>;
+ dma-names = "tx", "rx";
+ clocks = <&clock CLK_I2S1>, <&clock CLK_DIV_I2S1>;
+ clock-names = "iis", "i2s_opclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1_bus>;
+ };
- i2s0: i2s@03830000 {
- compatible = "samsung,s5pv210-i2s";
- status = "disabled";
- reg = <0x03830000 0x100>;
- dmas = <&pdma0 10
- &pdma0 9
- &pdma0 8>;
- dma-names = "tx", "rx", "tx-sec";
- clocks = <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_SCLK_I2S>;
- clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
- samsung,idma-addr = <0x03000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2s0_bus>;
- };
+ i2s2: i2s@12D70000 {
+ compatible = "samsung,s3c6410-i2s";
+ status = "disabled";
+ reg = <0x12D70000 0x100>;
+ dmas = <&pdma0 12
+ &pdma0 11>;
+ dma-names = "tx", "rx";
+ clocks = <&clock CLK_I2S2>, <&clock CLK_DIV_I2S2>;
+ clock-names = "iis", "i2s_opclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s2_bus>;
+ };
- i2s1: i2s@12D60000 {
- compatible = "samsung,s3c6410-i2s";
- status = "disabled";
- reg = <0x12D60000 0x100>;
- dmas = <&pdma1 12
- &pdma1 11>;
- dma-names = "tx", "rx";
- clocks = <&clock CLK_I2S1>, <&clock CLK_DIV_I2S1>;
- clock-names = "iis", "i2s_opclk0";
- pinctrl-names = "default";
- pinctrl-0 = <&i2s1_bus>;
- };
+ usb_dwc3 {
+ compatible = "samsung,exynos5250-dwusb3";
+ clocks = <&clock CLK_USB3>;
+ clock-names = "usbdrd30";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbdrd_dwc3: dwc3@12000000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x12000000 0x10000>;
+ interrupts = <0 72 0>;
+ phys = <&usbdrd_phy 0>, <&usbdrd_phy 1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
- i2s2: i2s@12D70000 {
- compatible = "samsung,s3c6410-i2s";
- status = "disabled";
- reg = <0x12D70000 0x100>;
- dmas = <&pdma0 12
- &pdma0 11>;
- dma-names = "tx", "rx";
- clocks = <&clock CLK_I2S2>, <&clock CLK_DIV_I2S2>;
- clock-names = "iis", "i2s_opclk0";
- pinctrl-names = "default";
- pinctrl-0 = <&i2s2_bus>;
- };
+ usbdrd_phy: phy@12100000 {
+ compatible = "samsung,exynos5250-usbdrd-phy";
+ reg = <0x12100000 0x100>;
+ clocks = <&clock CLK_USB3>, <&clock CLK_FIN_PLL>;
+ clock-names = "phy", "ref";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ #phy-cells = <1>;
+ };
- usb_dwc3 {
- compatible = "samsung,exynos5250-dwusb3";
- clocks = <&clock CLK_USB3>;
- clock-names = "usbdrd30";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
+ ehci: usb@12110000 {
+ compatible = "samsung,exynos4210-ehci";
+ reg = <0x12110000 0x100>;
+ interrupts = <0 71 0>;
- usbdrd_dwc3: dwc3@12000000 {
- compatible = "synopsys,dwc3";
- reg = <0x12000000 0x10000>;
- interrupts = <0 72 0>;
- phys = <&usbdrd_phy 0>, <&usbdrd_phy 1>;
- phy-names = "usb2-phy", "usb3-phy";
+ clocks = <&clock CLK_USB2>;
+ clock-names = "usbhost";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phys = <&usb2_phy_gen 1>;
+ };
};
- };
-
- usbdrd_phy: phy@12100000 {
- compatible = "samsung,exynos5250-usbdrd-phy";
- reg = <0x12100000 0x100>;
- clocks = <&clock CLK_USB3>, <&clock CLK_FIN_PLL>;
- clock-names = "phy", "ref";
- samsung,pmu-syscon = <&pmu_system_controller>;
- #phy-cells = <1>;
- };
- ehci: usb@12110000 {
- compatible = "samsung,exynos4210-ehci";
- reg = <0x12110000 0x100>;
- interrupts = <0 71 0>;
+ ohci: usb@12120000 {
+ compatible = "samsung,exynos4210-ohci";
+ reg = <0x12120000 0x100>;
+ interrupts = <0 71 0>;
- clocks = <&clock CLK_USB2>;
- clock-names = "usbhost";
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- phys = <&usb2_phy_gen 1>;
+ clocks = <&clock CLK_USB2>;
+ clock-names = "usbhost";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phys = <&usb2_phy_gen 1>;
+ };
};
- };
- ohci: usb@12120000 {
- compatible = "samsung,exynos4210-ohci";
- reg = <0x12120000 0x100>;
- interrupts = <0 71 0>;
-
- clocks = <&clock CLK_USB2>;
- clock-names = "usbhost";
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- phys = <&usb2_phy_gen 1>;
+ usb2_phy_gen: phy@12130000 {
+ compatible = "samsung,exynos5250-usb2-phy";
+ reg = <0x12130000 0x100>;
+ clocks = <&clock CLK_USB2>, <&clock CLK_FIN_PLL>;
+ clock-names = "phy", "ref";
+ #phy-cells = <1>;
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ samsung,pmureg-phandle = <&pmu_system_controller>;
};
- };
- usb2_phy_gen: phy@12130000 {
- compatible = "samsung,exynos5250-usb2-phy";
- reg = <0x12130000 0x100>;
- clocks = <&clock CLK_USB2>, <&clock CLK_FIN_PLL>;
- clock-names = "phy", "ref";
- #phy-cells = <1>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- samsung,pmureg-phandle = <&pmu_system_controller>;
- };
+ amba {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ pdma0: pdma@121A0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x121A0000 0x1000>;
+ interrupts = <0 34 0>;
+ clocks = <&clock CLK_PDMA0>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+
+ pdma1: pdma@121B0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x121B0000 0x1000>;
+ interrupts = <0 35 0>;
+ clocks = <&clock CLK_PDMA1>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+
+ mdma0: mdma@10800000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x10800000 0x1000>;
+ interrupts = <0 33 0>;
+ clocks = <&clock CLK_MDMA0>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <1>;
+ };
+
+ mdma1: mdma@11C10000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x11C10000 0x1000>;
+ interrupts = <0 124 0>;
+ clocks = <&clock CLK_MDMA1>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <1>;
+ };
+ };
- pwm: pwm@12dd0000 {
- compatible = "samsung,exynos4210-pwm";
- reg = <0x12dd0000 0x100>;
- samsung,pwm-outputs = <0>, <1>, <2>, <3>;
- #pwm-cells = <3>;
- clocks = <&clock CLK_PWM>;
- clock-names = "timers";
- };
+ gsc_0: gsc@13e00000 {
+ compatible = "samsung,exynos5-gsc";
+ reg = <0x13e00000 0x1000>;
+ interrupts = <0 85 0>;
+ power-domains = <&pd_gsc>;
+ clocks = <&clock CLK_GSCL0>;
+ clock-names = "gscl";
+ iommu = <&sysmmu_gsc0>;
+ };
- amba {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- interrupt-parent = <&gic>;
- ranges;
-
- pdma0: pdma@121A0000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x121A0000 0x1000>;
- interrupts = <0 34 0>;
- clocks = <&clock CLK_PDMA0>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <32>;
- };
-
- pdma1: pdma@121B0000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x121B0000 0x1000>;
- interrupts = <0 35 0>;
- clocks = <&clock CLK_PDMA1>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <32>;
- };
-
- mdma0: mdma@10800000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x10800000 0x1000>;
- interrupts = <0 33 0>;
- clocks = <&clock CLK_MDMA0>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <1>;
- };
-
- mdma1: mdma@11C10000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x11C10000 0x1000>;
- interrupts = <0 124 0>;
- clocks = <&clock CLK_MDMA1>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <1>;
+ gsc_1: gsc@13e10000 {
+ compatible = "samsung,exynos5-gsc";
+ reg = <0x13e10000 0x1000>;
+ interrupts = <0 86 0>;
+ power-domains = <&pd_gsc>;
+ clocks = <&clock CLK_GSCL1>;
+ clock-names = "gscl";
+ iommu = <&sysmmu_gsc1>;
};
- };
- gsc_0: gsc@13e00000 {
- compatible = "samsung,exynos5-gsc";
- reg = <0x13e00000 0x1000>;
- interrupts = <0 85 0>;
- power-domains = <&pd_gsc>;
- clocks = <&clock CLK_GSCL0>;
- clock-names = "gscl";
- iommu = <&sysmmu_gsc0>;
- };
+ gsc_2: gsc@13e20000 {
+ compatible = "samsung,exynos5-gsc";
+ reg = <0x13e20000 0x1000>;
+ interrupts = <0 87 0>;
+ power-domains = <&pd_gsc>;
+ clocks = <&clock CLK_GSCL2>;
+ clock-names = "gscl";
+ iommu = <&sysmmu_gsc2>;
+ };
- gsc_1: gsc@13e10000 {
- compatible = "samsung,exynos5-gsc";
- reg = <0x13e10000 0x1000>;
- interrupts = <0 86 0>;
- power-domains = <&pd_gsc>;
- clocks = <&clock CLK_GSCL1>;
- clock-names = "gscl";
- iommu = <&sysmmu_gsc1>;
- };
+ gsc_3: gsc@13e30000 {
+ compatible = "samsung,exynos5-gsc";
+ reg = <0x13e30000 0x1000>;
+ interrupts = <0 88 0>;
+ power-domains = <&pd_gsc>;
+ clocks = <&clock CLK_GSCL3>;
+ clock-names = "gscl";
+ iommu = <&sysmmu_gsc3>;
+ };
- gsc_2: gsc@13e20000 {
- compatible = "samsung,exynos5-gsc";
- reg = <0x13e20000 0x1000>;
- interrupts = <0 87 0>;
- power-domains = <&pd_gsc>;
- clocks = <&clock CLK_GSCL2>;
- clock-names = "gscl";
- iommu = <&sysmmu_gsc2>;
- };
+ hdmi: hdmi@14530000 {
+ compatible = "samsung,exynos4212-hdmi";
+ reg = <0x14530000 0x70000>;
+ power-domains = <&pd_disp1>;
+ interrupts = <0 95 0>;
+ clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+ <&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+ <&clock CLK_MOUT_HDMI>;
+ clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
+ "sclk_hdmiphy", "mout_hdmi";
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ };
- gsc_3: gsc@13e30000 {
- compatible = "samsung,exynos5-gsc";
- reg = <0x13e30000 0x1000>;
- interrupts = <0 88 0>;
- power-domains = <&pd_gsc>;
- clocks = <&clock CLK_GSCL3>;
- clock-names = "gscl";
- iommu = <&sysmmu_gsc3>;
- };
+ mixer@14450000 {
+ compatible = "samsung,exynos5250-mixer";
+ reg = <0x14450000 0x10000>;
+ power-domains = <&pd_disp1>;
+ interrupts = <0 94 0>;
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>;
+ clock-names = "mixer", "hdmi", "sclk_hdmi";
+ iommus = <&sysmmu_tv>;
+ };
- hdmi: hdmi@14530000 {
- compatible = "samsung,exynos4212-hdmi";
- reg = <0x14530000 0x70000>;
- power-domains = <&pd_disp1>;
- interrupts = <0 95 0>;
- clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
- <&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
- <&clock CLK_MOUT_HDMI>;
- clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
- "sclk_hdmiphy", "mout_hdmi";
- samsung,syscon-phandle = <&pmu_system_controller>;
- };
+ dp_phy: video-phy {
+ compatible = "samsung,exynos5250-dp-video-phy";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ #phy-cells = <0>;
+ };
- mixer@14450000 {
- compatible = "samsung,exynos5250-mixer";
- reg = <0x14450000 0x10000>;
- power-domains = <&pd_disp1>;
- interrupts = <0 94 0>;
- clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
- <&clock CLK_SCLK_HDMI>;
- clock-names = "mixer", "hdmi", "sclk_hdmi";
- iommus = <&sysmmu_tv>;
- };
+ adc: adc@12D10000 {
+ compatible = "samsung,exynos-adc-v1";
+ reg = <0x12D10000 0x100>;
+ interrupts = <0 106 0>;
+ clocks = <&clock CLK_ADC>;
+ clock-names = "adc";
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ status = "disabled";
+ };
- dp_phy: video-phy {
- compatible = "samsung,exynos5250-dp-video-phy";
- samsung,pmu-syscon = <&pmu_system_controller>;
- #phy-cells = <0>;
- };
+ sss@10830000 {
+ compatible = "samsung,exynos4210-secss";
+ reg = <0x10830000 0x300>;
+ interrupts = <0 112 0>;
+ clocks = <&clock CLK_SSS>;
+ clock-names = "secss";
+ };
- adc: adc@12D10000 {
- compatible = "samsung,exynos-adc-v1";
- reg = <0x12D10000 0x100>;
- interrupts = <0 106 0>;
- clocks = <&clock CLK_ADC>;
- clock-names = "adc";
- #io-channel-cells = <1>;
- io-channel-ranges;
- samsung,syscon-phandle = <&pmu_system_controller>;
- status = "disabled";
- };
+ sysmmu_g2d: sysmmu@10A60000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x10A60000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <24 5>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_2D>, <&clock CLK_G2D>;
+ #iommu-cells = <0>;
+ };
- sss@10830000 {
- compatible = "samsung,exynos4210-secss";
- reg = <0x10830000 0x300>;
- interrupts = <0 112 0>;
- clocks = <&clock CLK_SSS>;
- clock-names = "secss";
- };
+ sysmmu_mfc_r: sysmmu@11200000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11200000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <6 2>;
+ power-domains = <&pd_mfc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MFCR>, <&clock CLK_MFC>;
+ #iommu-cells = <0>;
+ };
- sysmmu_g2d: sysmmu@10A60000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x10A60000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <24 5>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_2D>, <&clock CLK_G2D>;
- #iommu-cells = <0>;
- };
+ sysmmu_mfc_l: sysmmu@11210000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11210000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <8 5>;
+ power-domains = <&pd_mfc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MFCL>, <&clock CLK_MFC>;
+ #iommu-cells = <0>;
+ };
- sysmmu_mfc_r: sysmmu@11200000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11200000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <6 2>;
- power-domains = <&pd_mfc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MFCR>, <&clock CLK_MFC>;
- #iommu-cells = <0>;
- };
+ sysmmu_rotator: sysmmu@11D40000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11D40000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <4 0>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_ROTATOR>, <&clock CLK_ROTATOR>;
+ #iommu-cells = <0>;
+ };
- sysmmu_mfc_l: sysmmu@11210000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11210000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <8 5>;
- power-domains = <&pd_mfc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MFCL>, <&clock CLK_MFC>;
- #iommu-cells = <0>;
- };
+ sysmmu_jpeg: sysmmu@11F20000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11F20000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <4 2>;
+ power-domains = <&pd_gsc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_JPEG>, <&clock CLK_JPEG>;
+ #iommu-cells = <0>;
+ };
- sysmmu_rotator: sysmmu@11D40000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11D40000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <4 0>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_ROTATOR>, <&clock CLK_ROTATOR>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_isp: sysmmu@13260000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13260000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <10 6>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_ISP>;
+ #iommu-cells = <0>;
+ };
- sysmmu_jpeg: sysmmu@11F20000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11F20000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <4 2>;
- power-domains = <&pd_gsc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_JPEG>, <&clock CLK_JPEG>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_drc: sysmmu@13270000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13270000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <11 6>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_DRC>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_isp: sysmmu@13260000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13260000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <10 6>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_ISP>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_fd: sysmmu@132A0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x132A0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <5 0>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_FD>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_drc: sysmmu@13270000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13270000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <11 6>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_DRC>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_scc: sysmmu@13280000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13280000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <5 2>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_SCC>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_fd: sysmmu@132A0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x132A0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <5 0>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_FD>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_scp: sysmmu@13290000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13290000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <3 6>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_SCP>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_scc: sysmmu@13280000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13280000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <5 2>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_SCC>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_mcuctl: sysmmu@132B0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x132B0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <5 4>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_MCU>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_scp: sysmmu@13290000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13290000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <3 6>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_SCP>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_odc: sysmmu@132C0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x132C0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <11 0>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_ODC>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_mcuctl: sysmmu@132B0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x132B0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <5 4>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_MCU>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_dis0: sysmmu@132D0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x132D0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <10 4>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_DIS0>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_odc: sysmmu@132C0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x132C0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <11 0>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_ODC>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_dis1: sysmmu@132E0000{
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x132E0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <9 4>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_DIS1>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_dis0: sysmmu@132D0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x132D0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <10 4>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_DIS0>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_3dnr: sysmmu@132F0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x132F0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <5 6>;
+ clock-names = "sysmmu";
+ clocks = <&clock CLK_SMMU_FIMC_3DNR>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_dis1: sysmmu@132E0000{
- compatible = "samsung,exynos-sysmmu";
- reg = <0x132E0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <9 4>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_DIS1>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_lite0: sysmmu@13C40000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13C40000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <3 4>;
+ power-domains = <&pd_gsc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_FIMC_LITE0>, <&clock CLK_CAMIF_TOP>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_3dnr: sysmmu@132F0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x132F0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <5 6>;
- clock-names = "sysmmu";
- clocks = <&clock CLK_SMMU_FIMC_3DNR>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimc_lite1: sysmmu@13C50000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13C50000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <24 1>;
+ power-domains = <&pd_gsc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_FIMC_LITE1>, <&clock CLK_CAMIF_TOP>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_lite0: sysmmu@13C40000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13C40000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <3 4>;
- power-domains = <&pd_gsc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_FIMC_LITE0>, <&clock CLK_CAMIF_TOP>;
- #iommu-cells = <0>;
- };
+ sysmmu_gsc0: sysmmu@13E80000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13E80000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <2 0>;
+ power-domains = <&pd_gsc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>;
+ #iommu-cells = <0>;
+ };
- sysmmu_fimc_lite1: sysmmu@13C50000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13C50000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <24 1>;
- power-domains = <&pd_gsc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_FIMC_LITE1>, <&clock CLK_CAMIF_TOP>;
- #iommu-cells = <0>;
- };
+ sysmmu_gsc1: sysmmu@13E90000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13E90000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <2 2>;
+ power-domains = <&pd_gsc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_GSCL1>, <&clock CLK_GSCL1>;
+ #iommu-cells = <0>;
+ };
- sysmmu_gsc0: sysmmu@13E80000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13E80000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <2 0>;
- power-domains = <&pd_gsc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>;
- #iommu-cells = <0>;
- };
+ sysmmu_gsc2: sysmmu@13EA0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13EA0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <2 4>;
+ power-domains = <&pd_gsc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_GSCL2>, <&clock CLK_GSCL2>;
+ #iommu-cells = <0>;
+ };
- sysmmu_gsc1: sysmmu@13E90000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13E90000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <2 2>;
- power-domains = <&pd_gsc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_GSCL1>, <&clock CLK_GSCL1>;
- #iommu-cells = <0>;
- };
+ sysmmu_gsc3: sysmmu@13EB0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13EB0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <2 6>;
+ power-domains = <&pd_gsc>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_GSCL3>, <&clock CLK_GSCL3>;
+ #iommu-cells = <0>;
+ };
- sysmmu_gsc2: sysmmu@13EA0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13EA0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <2 4>;
- power-domains = <&pd_gsc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_GSCL2>, <&clock CLK_GSCL2>;
- #iommu-cells = <0>;
- };
+ sysmmu_fimd1: sysmmu@14640000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x14640000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <3 2>;
+ power-domains = <&pd_disp1>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_FIMD1>, <&clock CLK_FIMD1>;
+ #iommu-cells = <0>;
+ };
- sysmmu_gsc3: sysmmu@13EB0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13EB0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <2 6>;
- power-domains = <&pd_gsc>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_GSCL3>, <&clock CLK_GSCL3>;
- #iommu-cells = <0>;
+ sysmmu_tv: sysmmu@14650000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x14650000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <7 4>;
+ power-domains = <&pd_disp1>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_TV>, <&clock CLK_MIXER>;
+ #iommu-cells = <0>;
+ };
};
- sysmmu_fimd1: sysmmu@14640000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x14640000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <3 2>;
- power-domains = <&pd_disp1>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_FIMD1>, <&clock CLK_FIMD1>;
- #iommu-cells = <0>;
- };
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tmu 0>;
- sysmmu_tv: sysmmu@14650000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x14650000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <7 4>;
- power-domains = <&pd_disp1>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_TV>, <&clock CLK_MIXER>;
- #iommu-cells = <0>;
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 9 9>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 15 15>;
+ };
+ };
+ };
};
};
iommus = <&sysmmu_fimd1>;
};
+&i2c_0 {
+ clocks = <&clock CLK_I2C0>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+};
+
+&i2c_1 {
+ clocks = <&clock CLK_I2C1>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+};
+
+&i2c_2 {
+ clocks = <&clock CLK_I2C2>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
+
+&i2c_3 {
+ clocks = <&clock CLK_I2C3>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+};
+
+&pwm {
+ clocks = <&clock CLK_PWM>;
+ clock-names = "timers";
+};
+
&rtc {
clocks = <&clock CLK_RTC>;
clock-names = "rtc";
--- /dev/null
+/*
+ * Hardkernel Odroid XU board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2016 Krzysztof Kozlowski
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include "exynos5410.dtsi"
+#include <dt-bindings/clock/maxim,max77802.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "exynos54xx-odroidxu-leds.dtsi"
+
+/ {
+ model = "Hardkernel Odroid XU";
+ compatible = "hardkernel,odroid-xu", "samsung,exynos5410", "samsung,exynos5";
+
+ memory {
+ reg = <0x40000000 0x7ea00000>;
+ };
+
+ chosen {
+ linux,stdout-path = &serial_2;
+ };
+
+ emmc_pwrseq: pwrseq {
+ pinctrl-0 = <&emmc_nrst_pin>;
+ pinctrl-names = "default";
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>;
+ };
+
+ fan0: pwm-fan {
+ compatible = "pwm-fan";
+ pwms = <&pwm 0 20972 0>;
+ cooling-min-state = <0>;
+ cooling-max-state = <3>;
+ #cooling-cells = <2>;
+ cooling-levels = <0 130 170 230>;
+ };
+
+ fin_pll: xxti {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "fin_pll";
+ #clock-cells = <0>;
+ };
+
+ firmware@02073000 {
+ compatible = "samsung,secure-firmware";
+ reg = <0x02073000 0x1000>;
+ };
+};
+
+&cpu0_thermal {
+ thermal-sensors = <&tmu_cpu0 0>;
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ trips {
+ cpu_alert0: cpu-alert-0 {
+ temperature = <50000>; /* millicelsius */
+ hysteresis = <5000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_alert1: cpu-alert-1 {
+ temperature = <60000>; /* millicelsius */
+ hysteresis = <5000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_alert2: cpu-alert-2 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <5000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_crit0: cpu-crit-0 {
+ temperature = <120000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&fan0 0 1>;
+ };
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&fan0 1 2>;
+ };
+ map2 {
+ trip = <&cpu_alert2>;
+ cooling-device = <&fan0 2 3>;
+ };
+ };
+};
+
+&hsi2c_4 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <400000>;
+ status = "okay";
+
+ usb3503: usb-hub@08 {
+ compatible = "smsc,usb3503";
+ reg = <0x08>;
+
+ intn-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>;
+ connect-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpx1 4 GPIO_ACTIVE_HIGH>;
+ initial-mode = <1>;
+
+ clock-names = "refclk";
+ clocks = <&pmu_system_controller 0>;
+ refclk-frequency = <24000000>;
+ };
+
+ max77802: pmic@09 {
+ compatible = "maxim,max77802";
+ reg = <0x9>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <4 IRQ_TYPE_NONE>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77802_irq>, <&pmic_dvs_1>, <&pmic_dvs_2>,
+ <&pmic_dvs_3>;
+ #clock-cells = <1>;
+
+ inl1-supply = <&buck5_reg>;
+ inl2-supply = <&buck7_reg>;
+ inl3-supply = <&buck9_reg>;
+ inl4-supply = <&buck9_reg>;
+ inl5-supply = <&buck9_reg>;
+ inl6-supply = <&buck10_reg>;
+ inl7-supply = <&buck9_reg>;
+ /* inl9 supply is BOOST, not configured here */
+ inl10-supply = <&buck7_reg>;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "vdd_mem";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "vdd_kfc";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "buck7";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck8_reg: BUCK8 {
+ /* vdd_mmc0 */
+ regulator-name = "vddf_2v85";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "buck9";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "buck10";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "vdd_alive";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "vddq_m1_m2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "vddq_gpio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "vddq_mmc2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ /* Having it off prevents reboot */
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "vdd18_hsic";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "vdd18_bpll";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "vddq_lcd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "vdd10_hdmi";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "ldo9";
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "vdd18_mipi";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "vddq_mmc01";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ /*
+ * Having it off prevents accessing MMC after
+ * reboot with error:
+ * MMC Device 1: Clock OFF has been failed.
+ */
+ regulator-always-on;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "vdd33_usb3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "vddq_abbg0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "vddq_abbg1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "vdd10_usb3";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "ldo16";
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "cam_sensor_core";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "ldo18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "ldo19";
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "vdd_mmc0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo21_reg: LDO21 {
+ /* vdd_mmc2 */
+ regulator-name = "vddf_2v8";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "ldo22";
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "dp_p3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "cam_af";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "eth_p3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "usb30_extclk";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "ldo27";
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "ldo28";
+ };
+
+ ldo29_reg: LDO29 {
+ regulator-name = "ldo29";
+ };
+
+ ldo30_reg: LDO30 {
+ regulator-name = "vddq_e1_e2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo31_reg: LDO31 {
+ regulator-name = "ldo31";
+ };
+
+ /* On revisions with ti,ina231 this is sensor VS */
+ ldo32_reg: LDO32 {
+ regulator-name = "vs_power_meter";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo33_reg: LDO33 {
+ regulator-name = "ldo33";
+ };
+
+ ldo34_reg: LDO34 {
+ regulator-name = "ldo34";
+ };
+
+ ldo35_reg: LDO35 {
+ regulator-name = "ldo35";
+ };
+ };
+ };
+};
+
+&mmc_0 {
+ status = "okay";
+ mmc-pwrseq = <&emmc_pwrseq>;
+ cd-gpios = <&gpc0 2 GPIO_ACTIVE_LOW>;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ samsung,dw-mshc-hs400-timing = <0 2>;
+ samsung,read-strobe-delay = <90>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ vmmc-supply = <&ldo20_reg>;
+ vqmmc-supply = <&ldo11_reg>;
+};
+
+&mmc_2 {
+ status = "okay";
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ vmmc-supply = <&ldo21_reg>;
+ vqmmc-supply = <&ldo4_reg>;
+};
+
+&pinctrl_0 {
+ emmc_nrst_pin: emmc-nrst {
+ samsung,pins = "gpd1-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pmic_dvs_3: pmic-dvs-3 {
+ samsung,pins = "gpx0-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pmic_dvs_2: pmic-dvs-2 {
+ samsung,pins = "gpx0-1";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pmic_dvs_1: pmic-dvs-1 {
+ samsung,pins = "gpx0-2";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ samsung,pin-val = <1>;
+ };
+
+ max77802_irq: max77802-irq {
+ samsung,pins = "gpx0-4";
+ samsung,pin-function = <0xf>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pwm {
+ /*
+ * PWM 0 -- fan
+ * PWM 1 -- Green LED
+ * PWM 2 -- Blue LED
+ * PWM 3 -- on MIPI connector for backlight
+ */
+ pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+ clocks = <&clock CLK_RTC>, <&max77802 MAX77802_CLK_32K_AP>;
+ clock-names = "rtc", "rtc_src";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&tmu_cpu0 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu1 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu2 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu3 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "host";
+};
+
+&usbdrd_dwc3_1 {
+ dr_mode = "peripheral";
+};
+
+&usbdrd3_0 {
+ vdd33-supply = <&ldo12_reg>;
+ vdd10-supply = <&ldo15_reg>;
+};
+
+&usbdrd3_1 {
+ vdd33-supply = <&ldo12_reg>;
+ vdd10-supply = <&ldo15_reg>;
+};
interrupt-controller;
#interrupt-cells = <2>;
};
+
+ uart0_data: uart0-data {
+ samsung,pins = "gpa0-0", "gpa0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart0_fctl: uart0-fctl {
+ samsung,pins = "gpa0-2", "gpa0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart1_data: uart1-data {
+ samsung,pins = "gpa0-4", "gpa0-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart1_fctl: uart1-fctl {
+ samsung,pins = "gpa0-6", "gpa0-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c2_bus: i2c2-bus {
+ samsung,pins = "gpa0-6", "gpa0-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart2_data: uart2-data {
+ samsung,pins = "gpa1-0", "gpa1-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart2_fctl: uart2-fctl {
+ samsung,pins = "gpa1-2", "gpa1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c3_bus: i2c3-bus {
+ samsung,pins = "gpa1-2", "gpa1-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart3_data: uart3-data {
+ samsung,pins = "gpa1-4", "gpa1-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c4_hs_bus: i2c4-hs-bus {
+ samsung,pins = "gpa2-0", "gpa2-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c5_hs_bus: i2c5-hs-bus {
+ samsung,pins = "gpa2-2", "gpa2-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c6_hs_bus: i2c6-hs-bus {
+ samsung,pins = "gpb1-3", "gpb1-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm0_out: pwm0-out {
+ samsung,pins = "gpb2-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm1_out: pwm1-out {
+ samsung,pins = "gpb2-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm2_out: pwm2-out {
+ samsung,pins = "gpb2-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm3_out: pwm3-out {
+ samsung,pins = "gpb2-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c7_hs_bus: i2c7-hs-bus {
+ samsung,pins = "gpb2-2", "gpb2-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c0_bus: i2c0-bus {
+ samsung,pins = "gpb3-0", "gpb3-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c1_bus: i2c1-bus {
+ samsung,pins = "gpb3-2", "gpb3-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ sd0_clk: sd0-clk {
+ samsung,pins = "gpc0-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cmd: sd0-cmd {
+ samsung,pins = "gpc0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cd: sd0-cd {
+ samsung,pins = "gpc0-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus1: sd0-bus-width1 {
+ samsung,pins = "gpc0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus4: sd0-bus-width4 {
+ samsung,pins = "gpc0-4", "gpc0-5", "gpc0-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_clk: sd2-clk {
+ samsung,pins = "gpc2-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_cmd: sd2-cmd {
+ samsung,pins = "gpc2-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_cd: sd2-cd {
+ samsung,pins = "gpc2-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus1: sd2-bus-width1 {
+ samsung,pins = "gpc2-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus4: sd2-bus-width4 {
+ samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus8: sd0-bus-width8 {
+ samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
};
&pinctrl_1 {
};
};
-&uart0 {
+&serial_0 {
status = "okay";
};
-&uart1 {
+&serial_1 {
status = "okay";
};
-&uart2 {
+&serial_2 {
status = "okay";
};
* published by the Free Software Foundation.
*/
-#include "skeleton.dtsi"
+#include "exynos54xx.dtsi"
#include "exynos-syscon-restart.dtsi"
#include <dt-bindings/clock/exynos5410.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
compatible = "samsung,exynos5410", "samsung,exynos5";
pinctrl1 = &pinctrl_1;
pinctrl2 = &pinctrl_2;
pinctrl3 = &pinctrl_3;
- serial0 = &uart0;
- serial1 = &uart1;
- serial2 = &uart2;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
- CPU0: cpu@0 {
+ cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x0>;
clock-frequency = <1600000000>;
};
- CPU1: cpu@1 {
+ cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x1>;
clock-frequency = <1600000000>;
};
- CPU2: cpu@2 {
+ cpu2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x2>;
clock-frequency = <1600000000>;
};
- CPU3: cpu@3 {
+ cpu3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x3>;
#size-cells = <1>;
ranges;
- combiner: interrupt-controller@10440000 {
- compatible = "samsung,exynos4210-combiner";
- #interrupt-cells = <2>;
- interrupt-controller;
- samsung,combiner-nr = <32>;
- reg = <0x10440000 0x1000>;
- interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
- <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
- <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
- <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
- <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
- <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
- <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
- <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>;
- };
-
- gic: interrupt-controller@10481000 {
- compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
- #interrupt-cells = <3>;
- interrupt-controller;
- reg = <0x10481000 0x1000>,
- <0x10482000 0x1000>,
- <0x10484000 0x2000>,
- <0x10486000 0x2000>;
- interrupts = <1 9 0xf04>;
- };
-
- chipid@10000000 {
- compatible = "samsung,exynos4210-chipid";
- reg = <0x10000000 0x100>;
- };
-
- sromc: memory-controller@12250000 {
- compatible = "samsung,exynos4210-srom";
- reg = <0x12250000 0x14>;
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0x04000000 0x20000
- 1 0 0x05000000 0x20000
- 2 0 0x06000000 0x20000
- 3 0 0x07000000 0x20000>;
- };
-
pmu_system_controller: system-controller@10040000 {
compatible = "samsung,exynos5410-pmu", "syscon";
reg = <0x10040000 0x5000>;
+ clock-names = "clkout16";
+ clocks = <&fin_pll>;
+ #clock-cells = <1>;
};
- mct: mct@101C0000 {
- compatible = "samsung,exynos4210-mct";
- reg = <0x101C0000 0xB00>;
- interrupt-parent = <&interrupt_map>;
- interrupts = <0>, <1>, <2>, <3>,
- <4>, <5>, <6>, <7>,
- <8>, <9>, <10>, <11>;
- clocks = <&fin_pll>, <&clock CLK_MCT>;
- clock-names = "fin_pll", "mct";
-
- interrupt_map: interrupt-map {
- #interrupt-cells = <1>;
- #address-cells = <0>;
- #size-cells = <0>;
- interrupt-map = <0 &combiner 23 3>,
- <1 &combiner 23 4>,
- <2 &combiner 25 2>,
- <3 &combiner 25 3>,
- <4 &gic 0 120 0>,
- <5 &gic 0 121 0>,
- <6 &gic 0 122 0>,
- <7 &gic 0 123 0>,
- <8 &gic 0 128 0>,
- <9 &gic 0 129 0>,
- <10 &gic 0 130 0>,
- <11 &gic 0 131 0>;
- };
+ clock: clock-controller@10010000 {
+ compatible = "samsung,exynos5410-clock";
+ reg = <0x10010000 0x30000>;
+ #clock-cells = <1>;
};
- sysram@02020000 {
- compatible = "mmio-sram";
- reg = <0x02020000 0x54000>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0x02020000 0x54000>;
+ tmu_cpu0: tmu@10060000 {
+ compatible = "samsung,exynos5420-tmu";
+ reg = <0x10060000 0x100>;
+ interrupts = <GIC_SPI 65 0>;
+ clocks = <&clock CLK_TMU>;
+ clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
- smp-sysram@0 {
- compatible = "samsung,exynos4210-sysram";
- reg = <0x0 0x1000>;
- };
+ tmu_cpu1: tmu@10064000 {
+ compatible = "samsung,exynos5420-tmu";
+ reg = <0x10064000 0x100>;
+ interrupts = <GIC_SPI 183 0>;
+ clocks = <&clock CLK_TMU>;
+ clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
- smp-sysram@53000 {
- compatible = "samsung,exynos4210-sysram-ns";
- reg = <0x53000 0x1000>;
- };
+ tmu_cpu2: tmu@10068000 {
+ compatible = "samsung,exynos5420-tmu";
+ reg = <0x10068000 0x100>;
+ interrupts = <GIC_SPI 184 0>;
+ clocks = <&clock CLK_TMU>;
+ clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
};
- clock: clock-controller@10010000 {
- compatible = "samsung,exynos5410-clock";
- reg = <0x10010000 0x30000>;
- #clock-cells = <1>;
+ tmu_cpu3: tmu@1006c000 {
+ compatible = "samsung,exynos5420-tmu";
+ reg = <0x1006c000 0x100>;
+ interrupts = <GIC_SPI 185 0>;
+ clocks = <&clock CLK_TMU>;
+ clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
};
mmc_0: mmc@12200000 {
reg = <0x03860000 0x1000>;
interrupts = <0 47 0>;
};
+ };
- uart0: serial@12C00000 {
- compatible = "samsung,exynos4210-uart";
- reg = <0x12C00000 0x100>;
- interrupts = <0 51 0>;
- clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
- clock-names = "uart", "clk_uart_baud0";
- status = "disabled";
+ thermal-zones {
+ cpu0_thermal: cpu0-thermal {
+ thermal-sensors = <&tmu_cpu0>;
+ #include "exynos5420-trip-points.dtsi"
};
-
- uart1: serial@12C10000 {
- compatible = "samsung,exynos4210-uart";
- reg = <0x12C10000 0x100>;
- interrupts = <0 52 0>;
- clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
- clock-names = "uart", "clk_uart_baud0";
- status = "disabled";
+ cpu1_thermal: cpu1-thermal {
+ thermal-sensors = <&tmu_cpu1>;
+ #include "exynos5420-trip-points.dtsi"
};
-
- uart2: serial@12C20000 {
- compatible = "samsung,exynos4210-uart";
- reg = <0x12C20000 0x100>;
- interrupts = <0 53 0>;
- clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
- clock-names = "uart", "clk_uart_baud0";
- status = "disabled";
+ cpu2_thermal: cpu2-thermal {
+ thermal-sensors = <&tmu_cpu2>;
+ #include "exynos5420-trip-points.dtsi"
+ };
+ cpu3_thermal: cpu3-thermal {
+ thermal-sensors = <&tmu_cpu3>;
+ #include "exynos5420-trip-points.dtsi"
};
};
};
+&i2c_0 {
+ clocks = <&clock CLK_I2C0>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+};
+
+&i2c_1 {
+ clocks = <&clock CLK_I2C1>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+};
+
+&i2c_2 {
+ clocks = <&clock CLK_I2C2>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
+
+&i2c_3 {
+ clocks = <&clock CLK_I2C3>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+};
+
+&hsi2c_4 {
+ clocks = <&clock CLK_USI0>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_hs_bus>;
+};
+
+&hsi2c_5 {
+ clocks = <&clock CLK_USI1>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_hs_bus>;
+};
+
+&hsi2c_6 {
+ clocks = <&clock CLK_USI2>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_hs_bus>;
+};
+
+&hsi2c_7 {
+ clocks = <&clock CLK_USI3>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_hs_bus>;
+};
+
+&mct {
+ clocks = <&fin_pll>, <&clock CLK_MCT>;
+ clock-names = "fin_pll", "mct";
+};
+
+&pwm {
+ clocks = <&clock CLK_PWM>;
+ clock-names = "timers";
+};
+
+&rtc {
+ clocks = <&clock CLK_RTC>;
+ clock-names = "rtc";
+ interrupt-parent = <&pmu_system_controller>;
+ status = "disabled";
+};
+
+&serial_0 {
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_1 {
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_2 {
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_3 {
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&sss {
+ clocks = <&clock CLK_SSS>;
+ clock-names = "secss";
+};
+
+&sromc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x04000000 0x20000
+ 1 0 0x05000000 0x20000
+ 2 0 0x06000000 0x20000
+ 3 0 0x07000000 0x20000>;
+};
+
+&usbdrd3_0 {
+ clocks = <&clock CLK_USBD300>;
+ clock-names = "usbdrd30";
+};
+
+&usbdrd_phy0 {
+ clocks = <&clock CLK_USBD300>, <&clock CLK_SCLK_USBPHY300>;
+ clock-names = "phy", "ref";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+};
+
+&usbdrd3_1 {
+ clocks = <&clock CLK_USBD301>;
+ clock-names = "usbdrd30";
+};
+
+&usbdrd_dwc3_1 {
+ interrupts = <GIC_SPI 200 0>;
+};
+
+&usbdrd_phy1 {
+ clocks = <&clock CLK_USBD301>, <&clock CLK_SCLK_USBPHY301>;
+ clock-names = "phy", "ref";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+};
+
+&usbhost1 {
+ clocks = <&clock CLK_USBH20>;
+ clock-names = "usbhost";
+};
+
+&usbhost2 {
+ clocks = <&clock CLK_USBH20>;
+ clock-names = "usbhost";
+};
+
+&usb2_phy {
+ clocks = <&clock CLK_USBH20>, <&clock CLK_SCLK_USBPHY300>;
+ clock-names = "phy", "ref";
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ samsung,pmureg-phandle = <&pmu_system_controller>;
+};
+
+&watchdog {
+ clocks = <&clock CLK_WDT>;
+ clock-names = "watchdog";
+ samsung,syscon-phandle = <&pmu_system_controller>;
+};
+
#include "exynos5410-pinctrl.dtsi"
};
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
broken-cd;
regulator-name = "vdd_1v2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
regulator-name = "vdd_1v35";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-name = "vdd_2v";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-name = "vdd_1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-name = "vdd_ldo9";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-always-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-mode = <MAX77802_OPMODE_LP>;
regulator-name = "vdd_ldo10";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-always-on;
regulator-state-mem {
regulator-off-in-suspend;
};
status = "okay";
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
num-slots = <1>;
status = "okay";
};
+&tmu_cpu0 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu1 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu2 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu3 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_gpu {
+ vtmu-supply = <&ldo10_reg>;
+};
+
&usbdrd_dwc3_0 {
dr_mode = "host";
};
samsung,pin-drv = <3>;
};
- sd1_clk: sd1-clk {
- samsung,pins = "gpc1-0";
+ sd0_rclk: sd0-rclk {
+ samsung,pins = "gpc0-7";
samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
+ samsung,pin-pud = <1>;
samsung,pin-drv = <3>;
};
- sd0_rclk: sd0-rclk {
- samsung,pins = "gpc0-7";
+ sd1_clk: sd1-clk {
+ samsung,pins = "gpc1-0";
samsung,pin-function = <2>;
- samsung,pin-pud = <1>;
+ samsung,pin-pud = <0>;
samsung,pin-drv = <3>;
};
};
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
broken-cd;
* published by the Free Software Foundation.
*/
+#include "exynos54xx.dtsi"
#include <dt-bindings/clock/exynos5420.h>
-#include "exynos5.dtsi"
-
#include <dt-bindings/clock/exynos-audss-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
compatible = "samsung,exynos5420", "samsung,exynos5";
pinctrl2 = &pinctrl_2;
pinctrl3 = &pinctrl_3;
pinctrl4 = &pinctrl_4;
- i2c0 = &i2c_0;
- i2c1 = &i2c_1;
- i2c2 = &i2c_2;
- i2c3 = &i2c_3;
- i2c4 = &hsi2c_4;
- i2c5 = &hsi2c_5;
- i2c6 = &hsi2c_6;
- i2c7 = &hsi2c_7;
i2c8 = &hsi2c_8;
i2c9 = &hsi2c_9;
i2c10 = &hsi2c_10;
spi0 = &spi_0;
spi1 = &spi_1;
spi2 = &spi_2;
- usbdrdphy0 = &usbdrd_phy0;
- usbdrdphy1 = &usbdrd_phy1;
- };
-
- cluster_a15_opp_table: opp_table0 {
- compatible = "operating-points-v2";
- opp-shared;
- opp@1800000000 {
- opp-hz = /bits/ 64 <1800000000>;
- opp-microvolt = <1250000>;
- clock-latency-ns = <140000>;
- };
- opp@1700000000 {
- opp-hz = /bits/ 64 <1700000000>;
- opp-microvolt = <1212500>;
- clock-latency-ns = <140000>;
- };
- opp@1600000000 {
- opp-hz = /bits/ 64 <1600000000>;
- opp-microvolt = <1175000>;
- clock-latency-ns = <140000>;
- };
- opp@1500000000 {
- opp-hz = /bits/ 64 <1500000000>;
- opp-microvolt = <1137500>;
- clock-latency-ns = <140000>;
- };
- opp@1400000000 {
- opp-hz = /bits/ 64 <1400000000>;
- opp-microvolt = <1112500>;
- clock-latency-ns = <140000>;
- };
- opp@1300000000 {
- opp-hz = /bits/ 64 <1300000000>;
- opp-microvolt = <1062500>;
- clock-latency-ns = <140000>;
- };
- opp@1200000000 {
- opp-hz = /bits/ 64 <1200000000>;
- opp-microvolt = <1037500>;
- clock-latency-ns = <140000>;
- };
- opp@1100000000 {
- opp-hz = /bits/ 64 <1100000000>;
- opp-microvolt = <1012500>;
- clock-latency-ns = <140000>;
- };
- opp@1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = < 987500>;
- clock-latency-ns = <140000>;
- };
- opp@900000000 {
- opp-hz = /bits/ 64 <900000000>;
- opp-microvolt = < 962500>;
- clock-latency-ns = <140000>;
- };
- opp@800000000 {
- opp-hz = /bits/ 64 <800000000>;
- opp-microvolt = < 937500>;
- clock-latency-ns = <140000>;
- };
- opp@700000000 {
- opp-hz = /bits/ 64 <700000000>;
- opp-microvolt = < 912500>;
- clock-latency-ns = <140000>;
- };
- };
-
- cluster_a7_opp_table: opp_table1 {
- compatible = "operating-points-v2";
- opp-shared;
- opp@1300000000 {
- opp-hz = /bits/ 64 <1300000000>;
- opp-microvolt = <1275000>;
- clock-latency-ns = <140000>;
- };
- opp@1200000000 {
- opp-hz = /bits/ 64 <1200000000>;
- opp-microvolt = <1212500>;
- clock-latency-ns = <140000>;
- };
- opp@1100000000 {
- opp-hz = /bits/ 64 <1100000000>;
- opp-microvolt = <1162500>;
- clock-latency-ns = <140000>;
- };
- opp@1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <1112500>;
- clock-latency-ns = <140000>;
- };
- opp@900000000 {
- opp-hz = /bits/ 64 <900000000>;
- opp-microvolt = <1062500>;
- clock-latency-ns = <140000>;
- };
- opp@800000000 {
- opp-hz = /bits/ 64 <800000000>;
- opp-microvolt = <1025000>;
- clock-latency-ns = <140000>;
- };
- opp@700000000 {
- opp-hz = /bits/ 64 <700000000>;
- opp-microvolt = <975000>;
- clock-latency-ns = <140000>;
- };
- opp@600000000 {
- opp-hz = /bits/ 64 <600000000>;
- opp-microvolt = <937500>;
- clock-latency-ns = <140000>;
- };
};
/*
* by exynos5420-cpus.dtsi or exynos5422-cpus.dtsi.
*/
- cci: cci@10d20000 {
- compatible = "arm,cci-400";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x10d20000 0x1000>;
- ranges = <0x0 0x10d20000 0x6000>;
-
- cci_control0: slave-if@4000 {
- compatible = "arm,cci-400-ctrl-if";
- interface-type = "ace";
- reg = <0x4000 0x1000>;
- };
- cci_control1: slave-if@5000 {
- compatible = "arm,cci-400-ctrl-if";
- interface-type = "ace";
- reg = <0x5000 0x1000>;
+ soc: soc {
+ cluster_a15_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+ opp@1800000000 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <1250000>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1700000000 {
+ opp-hz = /bits/ 64 <1700000000>;
+ opp-microvolt = <1212500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1600000000 {
+ opp-hz = /bits/ 64 <1600000000>;
+ opp-microvolt = <1175000>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1137500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-microvolt = <1112500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1300000000 {
+ opp-hz = /bits/ 64 <1300000000>;
+ opp-microvolt = <1062500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1037500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1100000000 {
+ opp-hz = /bits/ 64 <1100000000>;
+ opp-microvolt = <1012500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = < 987500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@900000000 {
+ opp-hz = /bits/ 64 <900000000>;
+ opp-microvolt = < 962500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = < 937500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@700000000 {
+ opp-hz = /bits/ 64 <700000000>;
+ opp-microvolt = < 912500>;
+ clock-latency-ns = <140000>;
+ };
+ };
+
+ cluster_a7_opp_table: opp_table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+ opp@1300000000 {
+ opp-hz = /bits/ 64 <1300000000>;
+ opp-microvolt = <1275000>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1212500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1100000000 {
+ opp-hz = /bits/ 64 <1100000000>;
+ opp-microvolt = <1162500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <1112500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@900000000 {
+ opp-hz = /bits/ 64 <900000000>;
+ opp-microvolt = <1062500>;
+ clock-latency-ns = <140000>;
+ };
+ opp@800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = <1025000>;
+ clock-latency-ns = <140000>;
+ };
+ opp@700000000 {
+ opp-hz = /bits/ 64 <700000000>;
+ opp-microvolt = <975000>;
+ clock-latency-ns = <140000>;
+ };
+ opp@600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <937500>;
+ clock-latency-ns = <140000>;
+ };
+ };
+
+ cci: cci@10d20000 {
+ compatible = "arm,cci-400";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x10d20000 0x1000>;
+ ranges = <0x0 0x10d20000 0x6000>;
+
+ cci_control0: slave-if@4000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x4000 0x1000>;
+ };
+ cci_control1: slave-if@5000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x5000 0x1000>;
+ };
+ };
+
+ clock: clock-controller@10010000 {
+ compatible = "samsung,exynos5420-clock";
+ reg = <0x10010000 0x30000>;
+ #clock-cells = <1>;
+ };
+
+ clock_audss: audss-clock-controller@3810000 {
+ compatible = "samsung,exynos5420-audss-clock";
+ reg = <0x03810000 0x0C>;
+ #clock-cells = <1>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MAU_EPLL>,
+ <&clock CLK_SCLK_MAUDIO0>, <&clock CLK_SCLK_MAUPCM0>;
+ clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
+ };
+
+ mfc: codec@11000000 {
+ compatible = "samsung,mfc-v7";
+ reg = <0x11000000 0x10000>;
+ interrupts = <0 96 0>;
+ clocks = <&clock CLK_MFC>;
+ clock-names = "mfc";
+ power-domains = <&mfc_pd>;
+ iommus = <&sysmmu_mfc_l>, <&sysmmu_mfc_r>;
+ iommu-names = "left", "right";
+ };
+
+ mmc_0: mmc@12200000 {
+ compatible = "samsung,exynos5420-dw-mshc-smu";
+ interrupts = <0 75 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x12200000 0x2000>;
+ clocks = <&clock CLK_MMC0>, <&clock CLK_SCLK_MMC0>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x40>;
+ status = "disabled";
};
- };
-
- sysram@02020000 {
- compatible = "mmio-sram";
- reg = <0x02020000 0x54000>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0x02020000 0x54000>;
- smp-sysram@0 {
- compatible = "samsung,exynos4210-sysram";
- reg = <0x0 0x1000>;
+ mmc_1: mmc@12210000 {
+ compatible = "samsung,exynos5420-dw-mshc-smu";
+ interrupts = <0 76 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x12210000 0x2000>;
+ clocks = <&clock CLK_MMC1>, <&clock CLK_SCLK_MMC1>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x40>;
+ status = "disabled";
};
- smp-sysram@53000 {
- compatible = "samsung,exynos4210-sysram-ns";
- reg = <0x53000 0x1000>;
+ mmc_2: mmc@12220000 {
+ compatible = "samsung,exynos5420-dw-mshc";
+ interrupts = <0 77 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x12220000 0x1000>;
+ clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x40>;
+ status = "disabled";
};
- };
-
- clock: clock-controller@10010000 {
- compatible = "samsung,exynos5420-clock";
- reg = <0x10010000 0x30000>;
- #clock-cells = <1>;
- };
- clock_audss: audss-clock-controller@3810000 {
- compatible = "samsung,exynos5420-audss-clock";
- reg = <0x03810000 0x0C>;
- #clock-cells = <1>;
- clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MAU_EPLL>,
- <&clock CLK_SCLK_MAUDIO0>, <&clock CLK_SCLK_MAUPCM0>;
- clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
- };
-
- mfc: codec@11000000 {
- compatible = "samsung,mfc-v7";
- reg = <0x11000000 0x10000>;
- interrupts = <0 96 0>;
- clocks = <&clock CLK_MFC>;
- clock-names = "mfc";
- power-domains = <&mfc_pd>;
- iommus = <&sysmmu_mfc_l>, <&sysmmu_mfc_r>;
- iommu-names = "left", "right";
- };
+ nocp_mem0_0: nocp@10CA1000 {
+ compatible = "samsung,exynos5420-nocp";
+ reg = <0x10CA1000 0x200>;
+ status = "disabled";
+ };
- mmc_0: mmc@12200000 {
- compatible = "samsung,exynos5420-dw-mshc-smu";
- interrupts = <0 75 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x12200000 0x2000>;
- clocks = <&clock CLK_MMC0>, <&clock CLK_SCLK_MMC0>;
- clock-names = "biu", "ciu";
- fifo-depth = <0x40>;
- status = "disabled";
- };
+ nocp_mem0_1: nocp@10CA1400 {
+ compatible = "samsung,exynos5420-nocp";
+ reg = <0x10CA1400 0x200>;
+ status = "disabled";
+ };
- mmc_1: mmc@12210000 {
- compatible = "samsung,exynos5420-dw-mshc-smu";
- interrupts = <0 76 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x12210000 0x2000>;
- clocks = <&clock CLK_MMC1>, <&clock CLK_SCLK_MMC1>;
- clock-names = "biu", "ciu";
- fifo-depth = <0x40>;
- status = "disabled";
- };
+ nocp_mem1_0: nocp@10CA1800 {
+ compatible = "samsung,exynos5420-nocp";
+ reg = <0x10CA1800 0x200>;
+ status = "disabled";
+ };
- mmc_2: mmc@12220000 {
- compatible = "samsung,exynos5420-dw-mshc";
- interrupts = <0 77 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x12220000 0x1000>;
- clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>;
- clock-names = "biu", "ciu";
- fifo-depth = <0x40>;
- status = "disabled";
- };
+ nocp_mem1_1: nocp@10CA1C00 {
+ compatible = "samsung,exynos5420-nocp";
+ reg = <0x10CA1C00 0x200>;
+ status = "disabled";
+ };
- mct: mct@101C0000 {
- compatible = "samsung,exynos4210-mct";
- reg = <0x101C0000 0x800>;
- interrupt-controller;
- #interrupt-cells = <1>;
- interrupt-parent = <&mct_map>;
- interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>,
- <8>, <9>, <10>, <11>;
- clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
- clock-names = "fin_pll", "mct";
-
- mct_map: mct-map {
- #interrupt-cells = <1>;
- #address-cells = <0>;
- #size-cells = <0>;
- interrupt-map = <0 &combiner 23 3>,
- <1 &combiner 23 4>,
- <2 &combiner 25 2>,
- <3 &combiner 25 3>,
- <4 &gic 0 120 0>,
- <5 &gic 0 121 0>,
- <6 &gic 0 122 0>,
- <7 &gic 0 123 0>,
- <8 &gic 0 128 0>,
- <9 &gic 0 129 0>,
- <10 &gic 0 130 0>,
- <11 &gic 0 131 0>;
+ nocp_g3d_0: nocp@11A51000 {
+ compatible = "samsung,exynos5420-nocp";
+ reg = <0x11A51000 0x200>;
+ status = "disabled";
};
- };
- nocp_mem0_0: nocp@10CA1000 {
- compatible = "samsung,exynos5420-nocp";
- reg = <0x10CA1000 0x200>;
- status = "disabled";
- };
+ nocp_g3d_1: nocp@11A51400 {
+ compatible = "samsung,exynos5420-nocp";
+ reg = <0x11A51400 0x200>;
+ status = "disabled";
+ };
- nocp_mem0_1: nocp@10CA1400 {
- compatible = "samsung,exynos5420-nocp";
- reg = <0x10CA1400 0x200>;
- status = "disabled";
- };
+ gsc_pd: power-domain@10044000 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10044000 0x20>;
+ #power-domain-cells = <0>;
+ clocks = <&clock CLK_FIN_PLL>,
+ <&clock CLK_MOUT_USER_ACLK300_GSCL>,
+ <&clock CLK_GSCL0>, <&clock CLK_GSCL1>;
+ clock-names = "oscclk", "clk0", "asb0", "asb1";
+ };
- nocp_mem1_0: nocp@10CA1800 {
- compatible = "samsung,exynos5420-nocp";
- reg = <0x10CA1800 0x200>;
- status = "disabled";
- };
+ isp_pd: power-domain@10044020 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10044020 0x20>;
+ #power-domain-cells = <0>;
+ };
- nocp_mem1_1: nocp@10CA1C00 {
- compatible = "samsung,exynos5420-nocp";
- reg = <0x10CA1C00 0x200>;
- status = "disabled";
- };
+ mfc_pd: power-domain@10044060 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10044060 0x20>;
+ clocks = <&clock CLK_FIN_PLL>,
+ <&clock CLK_MOUT_USER_ACLK333>,
+ <&clock CLK_ACLK333>;
+ clock-names = "oscclk", "clk0","asb0";
+ #power-domain-cells = <0>;
+ };
- nocp_g3d_0: nocp@11A51000 {
- compatible = "samsung,exynos5420-nocp";
- reg = <0x11A51000 0x200>;
- status = "disabled";
- };
+ msc_pd: power-domain@10044120 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10044120 0x20>;
+ #power-domain-cells = <0>;
+ };
- nocp_g3d_1: nocp@11A51400 {
- compatible = "samsung,exynos5420-nocp";
- reg = <0x11A51400 0x200>;
- status = "disabled";
- };
+ disp_pd: power-domain@100440C0 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x100440C0 0x20>;
+ #power-domain-cells = <0>;
+ clocks = <&clock CLK_FIN_PLL>,
+ <&clock CLK_MOUT_USER_ACLK200_DISP1>,
+ <&clock CLK_MOUT_USER_ACLK300_DISP1>,
+ <&clock CLK_MOUT_USER_ACLK400_DISP1>,
+ <&clock CLK_FIMD1>, <&clock CLK_MIXER>;
+ clock-names = "oscclk", "clk0", "clk1", "clk2", "asb0", "asb1";
+ };
- gsc_pd: power-domain@10044000 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x10044000 0x20>;
- #power-domain-cells = <0>;
- clocks = <&clock CLK_FIN_PLL>,
- <&clock CLK_MOUT_USER_ACLK300_GSCL>,
- <&clock CLK_GSCL0>, <&clock CLK_GSCL1>;
- clock-names = "oscclk", "clk0", "asb0", "asb1";
- };
+ pinctrl_0: pinctrl@13400000 {
+ compatible = "samsung,exynos5420-pinctrl";
+ reg = <0x13400000 0x1000>;
+ interrupts = <0 45 0>;
- isp_pd: power-domain@10044020 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x10044020 0x20>;
- #power-domain-cells = <0>;
- };
+ wakeup-interrupt-controller {
+ compatible = "samsung,exynos4210-wakeup-eint";
+ interrupt-parent = <&gic>;
+ interrupts = <0 32 0>;
+ };
+ };
- mfc_pd: power-domain@10044060 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x10044060 0x20>;
- clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_USER_ACLK333>;
- clock-names = "oscclk", "clk0";
- #power-domain-cells = <0>;
- };
+ pinctrl_1: pinctrl@13410000 {
+ compatible = "samsung,exynos5420-pinctrl";
+ reg = <0x13410000 0x1000>;
+ interrupts = <0 78 0>;
+ };
- msc_pd: power-domain@10044120 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x10044120 0x20>;
- #power-domain-cells = <0>;
- };
+ pinctrl_2: pinctrl@14000000 {
+ compatible = "samsung,exynos5420-pinctrl";
+ reg = <0x14000000 0x1000>;
+ interrupts = <0 46 0>;
+ };
- disp_pd: power-domain@100440C0 {
- compatible = "samsung,exynos4210-pd";
- reg = <0x100440C0 0x20>;
- #power-domain-cells = <0>;
- clocks = <&clock CLK_FIN_PLL>,
- <&clock CLK_MOUT_USER_ACLK200_DISP1>,
- <&clock CLK_MOUT_USER_ACLK300_DISP1>,
- <&clock CLK_MOUT_USER_ACLK400_DISP1>,
- <&clock CLK_FIMD1>, <&clock CLK_MIXER>;
- clock-names = "oscclk", "clk0", "clk1", "clk2", "asb0", "asb1";
- };
+ pinctrl_3: pinctrl@14010000 {
+ compatible = "samsung,exynos5420-pinctrl";
+ reg = <0x14010000 0x1000>;
+ interrupts = <0 50 0>;
+ };
- pinctrl_0: pinctrl@13400000 {
- compatible = "samsung,exynos5420-pinctrl";
- reg = <0x13400000 0x1000>;
- interrupts = <0 45 0>;
+ pinctrl_4: pinctrl@03860000 {
+ compatible = "samsung,exynos5420-pinctrl";
+ reg = <0x03860000 0x1000>;
+ interrupts = <0 47 0>;
+ };
- wakeup-interrupt-controller {
- compatible = "samsung,exynos4210-wakeup-eint";
+ amba {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
interrupt-parent = <&gic>;
- interrupts = <0 32 0>;
+ ranges;
+
+ adma: adma@03880000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x03880000 0x1000>;
+ interrupts = <0 110 0>;
+ clocks = <&clock_audss EXYNOS_ADMA>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <6>;
+ #dma-requests = <16>;
+ };
+
+ pdma0: pdma@121A0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x121A0000 0x1000>;
+ interrupts = <0 34 0>;
+ clocks = <&clock CLK_PDMA0>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+
+ pdma1: pdma@121B0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x121B0000 0x1000>;
+ interrupts = <0 35 0>;
+ clocks = <&clock CLK_PDMA1>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+
+ mdma0: mdma@10800000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x10800000 0x1000>;
+ interrupts = <0 33 0>;
+ clocks = <&clock CLK_MDMA0>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <1>;
+ };
+
+ mdma1: mdma@11C10000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x11C10000 0x1000>;
+ interrupts = <0 124 0>;
+ clocks = <&clock CLK_MDMA1>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <1>;
+ /*
+ * MDMA1 can support both secure and non-secure
+ * AXI transactions. When this is enabled in
+ * the kernel for boards that run in secure
+ * mode, we are getting imprecise external
+ * aborts causing the kernel to oops.
+ */
+ status = "disabled";
+ };
+ };
+
+ i2s0: i2s@03830000 {
+ compatible = "samsung,exynos5420-i2s";
+ reg = <0x03830000 0x100>;
+ dmas = <&adma 0
+ &adma 2
+ &adma 1>;
+ dma-names = "tx", "rx", "tx-sec";
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+ #clock-cells = <1>;
+ clock-output-names = "i2s_cdclk0";
+ #sound-dai-cells = <1>;
+ samsung,idma-addr = <0x03000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_bus>;
+ status = "disabled";
};
- };
-
- pinctrl_1: pinctrl@13410000 {
- compatible = "samsung,exynos5420-pinctrl";
- reg = <0x13410000 0x1000>;
- interrupts = <0 78 0>;
- };
- pinctrl_2: pinctrl@14000000 {
- compatible = "samsung,exynos5420-pinctrl";
- reg = <0x14000000 0x1000>;
- interrupts = <0 46 0>;
- };
-
- pinctrl_3: pinctrl@14010000 {
- compatible = "samsung,exynos5420-pinctrl";
- reg = <0x14010000 0x1000>;
- interrupts = <0 50 0>;
- };
-
- pinctrl_4: pinctrl@03860000 {
- compatible = "samsung,exynos5420-pinctrl";
- reg = <0x03860000 0x1000>;
- interrupts = <0 47 0>;
- };
-
- amba {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- interrupt-parent = <&gic>;
- ranges;
-
- adma: adma@03880000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x03880000 0x1000>;
- interrupts = <0 110 0>;
- clocks = <&clock_audss EXYNOS_ADMA>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <6>;
- #dma-requests = <16>;
- };
-
- pdma0: pdma@121A0000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x121A0000 0x1000>;
- interrupts = <0 34 0>;
- clocks = <&clock CLK_PDMA0>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <32>;
- };
-
- pdma1: pdma@121B0000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x121B0000 0x1000>;
- interrupts = <0 35 0>;
- clocks = <&clock CLK_PDMA1>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <32>;
- };
-
- mdma0: mdma@10800000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x10800000 0x1000>;
- interrupts = <0 33 0>;
- clocks = <&clock CLK_MDMA0>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <1>;
- };
-
- mdma1: mdma@11C10000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x11C10000 0x1000>;
- interrupts = <0 124 0>;
- clocks = <&clock CLK_MDMA1>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- #dma-channels = <8>;
- #dma-requests = <1>;
- /*
- * MDMA1 can support both secure and non-secure
- * AXI transactions. When this is enabled in the kernel
- * for boards that run in secure mode, we are getting
- * imprecise external aborts causing the kernel to oops.
- */
+ i2s1: i2s@12D60000 {
+ compatible = "samsung,exynos5420-i2s";
+ reg = <0x12D60000 0x100>;
+ dmas = <&pdma1 12
+ &pdma1 11>;
+ dma-names = "tx", "rx";
+ clocks = <&clock CLK_I2S1>, <&clock CLK_SCLK_I2S1>;
+ clock-names = "iis", "i2s_opclk0";
+ #clock-cells = <1>;
+ clock-output-names = "i2s_cdclk1";
+ #sound-dai-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1_bus>;
status = "disabled";
};
- };
-
- i2s0: i2s@03830000 {
- compatible = "samsung,exynos5420-i2s";
- reg = <0x03830000 0x100>;
- dmas = <&adma 0
- &adma 2
- &adma 1>;
- dma-names = "tx", "rx", "tx-sec";
- clocks = <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_SCLK_I2S>;
- clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
- #clock-cells = <1>;
- clock-output-names = "i2s_cdclk0";
- #sound-dai-cells = <1>;
- samsung,idma-addr = <0x03000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2s0_bus>;
- status = "disabled";
- };
-
- i2s1: i2s@12D60000 {
- compatible = "samsung,exynos5420-i2s";
- reg = <0x12D60000 0x100>;
- dmas = <&pdma1 12
- &pdma1 11>;
- dma-names = "tx", "rx";
- clocks = <&clock CLK_I2S1>, <&clock CLK_SCLK_I2S1>;
- clock-names = "iis", "i2s_opclk0";
- #clock-cells = <1>;
- clock-output-names = "i2s_cdclk1";
- #sound-dai-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2s1_bus>;
- status = "disabled";
- };
-
- i2s2: i2s@12D70000 {
- compatible = "samsung,exynos5420-i2s";
- reg = <0x12D70000 0x100>;
- dmas = <&pdma0 12
- &pdma0 11>;
- dma-names = "tx", "rx";
- clocks = <&clock CLK_I2S2>, <&clock CLK_SCLK_I2S2>;
- clock-names = "iis", "i2s_opclk0";
- #clock-cells = <1>;
- clock-output-names = "i2s_cdclk2";
- #sound-dai-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2s2_bus>;
- status = "disabled";
- };
-
- spi_0: spi@12d20000 {
- compatible = "samsung,exynos4210-spi";
- reg = <0x12d20000 0x100>;
- interrupts = <0 68 0>;
- dmas = <&pdma0 5
- &pdma0 4>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_bus>;
- clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
- clock-names = "spi", "spi_busclk0";
- status = "disabled";
- };
-
- spi_1: spi@12d30000 {
- compatible = "samsung,exynos4210-spi";
- reg = <0x12d30000 0x100>;
- interrupts = <0 69 0>;
- dmas = <&pdma1 5
- &pdma1 4>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_bus>;
- clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
- clock-names = "spi", "spi_busclk0";
- status = "disabled";
- };
-
- spi_2: spi@12d40000 {
- compatible = "samsung,exynos4210-spi";
- reg = <0x12d40000 0x100>;
- interrupts = <0 70 0>;
- dmas = <&pdma0 7
- &pdma0 6>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_bus>;
- clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
- clock-names = "spi", "spi_busclk0";
- status = "disabled";
- };
-
- pwm: pwm@12dd0000 {
- compatible = "samsung,exynos4210-pwm";
- reg = <0x12dd0000 0x100>;
- samsung,pwm-outputs = <0>, <1>, <2>, <3>;
- #pwm-cells = <3>;
- clocks = <&clock CLK_PWM>;
- clock-names = "timers";
- };
-
- dp_phy: dp-video-phy {
- compatible = "samsung,exynos5420-dp-video-phy";
- samsung,pmu-syscon = <&pmu_system_controller>;
- #phy-cells = <0>;
- };
-
- mipi_phy: mipi-video-phy {
- compatible = "samsung,s5pv210-mipi-video-phy";
- syscon = <&pmu_system_controller>;
- #phy-cells = <1>;
- };
-
- dsi@14500000 {
- compatible = "samsung,exynos5410-mipi-dsi";
- reg = <0x14500000 0x10000>;
- interrupts = <0 82 0>;
- phys = <&mipi_phy 1>;
- phy-names = "dsim";
- clocks = <&clock CLK_DSIM1>, <&clock CLK_SCLK_MIPI1>;
- clock-names = "bus_clk", "pll_clk";
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
- adc: adc@12D10000 {
- compatible = "samsung,exynos-adc-v2";
- reg = <0x12D10000 0x100>;
- interrupts = <0 106 0>;
- clocks = <&clock CLK_TSADC>;
- clock-names = "adc";
- #io-channel-cells = <1>;
- io-channel-ranges;
- samsung,syscon-phandle = <&pmu_system_controller>;
- status = "disabled";
- };
-
- i2c_0: i2c@12C60000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C60000 0x100>;
- interrupts = <0 56 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C0>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
-
- i2c_1: i2c@12C70000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C70000 0x100>;
- interrupts = <0 57 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C1>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
-
- i2c_2: i2c@12C80000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C80000 0x100>;
- interrupts = <0 58 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C2>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
-
- i2c_3: i2c@12C90000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x12C90000 0x100>;
- interrupts = <0 59 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clock CLK_I2C3>;
- clock-names = "i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_bus>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- status = "disabled";
- };
- hsi2c_4: i2c@12CA0000 {
- compatible = "samsung,exynos5-hsi2c";
- reg = <0x12CA0000 0x1000>;
- interrupts = <0 60 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_hs_bus>;
- clocks = <&clock CLK_USI0>;
- clock-names = "hsi2c";
- status = "disabled";
- };
-
- hsi2c_5: i2c@12CB0000 {
- compatible = "samsung,exynos5-hsi2c";
- reg = <0x12CB0000 0x1000>;
- interrupts = <0 61 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_hs_bus>;
- clocks = <&clock CLK_USI1>;
- clock-names = "hsi2c";
- status = "disabled";
- };
-
- hsi2c_6: i2c@12CC0000 {
- compatible = "samsung,exynos5-hsi2c";
- reg = <0x12CC0000 0x1000>;
- interrupts = <0 62 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c6_hs_bus>;
- clocks = <&clock CLK_USI2>;
- clock-names = "hsi2c";
- status = "disabled";
- };
-
- hsi2c_7: i2c@12CD0000 {
- compatible = "samsung,exynos5-hsi2c";
- reg = <0x12CD0000 0x1000>;
- interrupts = <0 63 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c7_hs_bus>;
- clocks = <&clock CLK_USI3>;
- clock-names = "hsi2c";
- status = "disabled";
- };
-
- hsi2c_8: i2c@12E00000 {
- compatible = "samsung,exynos5-hsi2c";
- reg = <0x12E00000 0x1000>;
- interrupts = <0 87 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c8_hs_bus>;
- clocks = <&clock CLK_USI4>;
- clock-names = "hsi2c";
- status = "disabled";
- };
-
- hsi2c_9: i2c@12E10000 {
- compatible = "samsung,exynos5-hsi2c";
- reg = <0x12E10000 0x1000>;
- interrupts = <0 88 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c9_hs_bus>;
- clocks = <&clock CLK_USI5>;
- clock-names = "hsi2c";
- status = "disabled";
- };
-
- hsi2c_10: i2c@12E20000 {
- compatible = "samsung,exynos5-hsi2c";
- reg = <0x12E20000 0x1000>;
- interrupts = <0 203 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c10_hs_bus>;
- clocks = <&clock CLK_USI6>;
- clock-names = "hsi2c";
- status = "disabled";
- };
-
- hdmi: hdmi@14530000 {
- compatible = "samsung,exynos5420-hdmi";
- reg = <0x14530000 0x70000>;
- interrupts = <0 95 0>;
- clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
- <&clock CLK_DOUT_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
- <&clock CLK_MOUT_HDMI>;
- clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
- "sclk_hdmiphy", "mout_hdmi";
- phy = <&hdmiphy>;
- samsung,syscon-phandle = <&pmu_system_controller>;
- status = "disabled";
- power-domains = <&disp_pd>;
- };
-
- hdmiphy: hdmiphy@145D0000 {
- reg = <0x145D0000 0x20>;
- };
-
- mixer: mixer@14450000 {
- compatible = "samsung,exynos5420-mixer";
- reg = <0x14450000 0x10000>;
- interrupts = <0 94 0>;
- clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
- <&clock CLK_SCLK_HDMI>;
- clock-names = "mixer", "hdmi", "sclk_hdmi";
- power-domains = <&disp_pd>;
- iommus = <&sysmmu_tv>;
- };
-
- rotator: rotator@11C00000 {
- compatible = "samsung,exynos5250-rotator";
- reg = <0x11C00000 0x64>;
- interrupts = <0 84 0>;
- clocks = <&clock CLK_ROTATOR>;
- clock-names = "rotator";
- iommus = <&sysmmu_rotator>;
- };
-
- gsc_0: video-scaler@13e00000 {
- compatible = "samsung,exynos5-gsc";
- reg = <0x13e00000 0x1000>;
- interrupts = <0 85 0>;
- clocks = <&clock CLK_GSCL0>;
- clock-names = "gscl";
- power-domains = <&gsc_pd>;
- iommus = <&sysmmu_gscl0>;
- };
-
- gsc_1: video-scaler@13e10000 {
- compatible = "samsung,exynos5-gsc";
- reg = <0x13e10000 0x1000>;
- interrupts = <0 86 0>;
- clocks = <&clock CLK_GSCL1>;
- clock-names = "gscl";
- power-domains = <&gsc_pd>;
- iommus = <&sysmmu_gscl1>;
- };
-
- jpeg_0: jpeg@11F50000 {
- compatible = "samsung,exynos5420-jpeg";
- reg = <0x11F50000 0x1000>;
- interrupts = <0 89 0>;
- clock-names = "jpeg";
- clocks = <&clock CLK_JPEG>;
- iommus = <&sysmmu_jpeg0>;
- };
-
- jpeg_1: jpeg@11F60000 {
- compatible = "samsung,exynos5420-jpeg";
- reg = <0x11F60000 0x1000>;
- interrupts = <0 168 0>;
- clock-names = "jpeg";
- clocks = <&clock CLK_JPEG2>;
- iommus = <&sysmmu_jpeg1>;
- };
-
- pmu_system_controller: system-controller@10040000 {
- compatible = "samsung,exynos5420-pmu", "syscon";
- reg = <0x10040000 0x5000>;
- clock-names = "clkout16";
- clocks = <&clock CLK_FIN_PLL>;
- #clock-cells = <1>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupt-parent = <&gic>;
- };
-
- sysreg_system_controller: syscon@10050000 {
- compatible = "samsung,exynos5-sysreg", "syscon";
- reg = <0x10050000 0x5000>;
- };
-
- tmu_cpu0: tmu@10060000 {
- compatible = "samsung,exynos5420-tmu";
- reg = <0x10060000 0x100>;
- interrupts = <0 65 0>;
- clocks = <&clock CLK_TMU>;
- clock-names = "tmu_apbif";
- #include "exynos4412-tmu-sensor-conf.dtsi"
- };
-
- tmu_cpu1: tmu@10064000 {
- compatible = "samsung,exynos5420-tmu";
- reg = <0x10064000 0x100>;
- interrupts = <0 183 0>;
- clocks = <&clock CLK_TMU>;
- clock-names = "tmu_apbif";
- #include "exynos4412-tmu-sensor-conf.dtsi"
- };
-
- tmu_cpu2: tmu@10068000 {
- compatible = "samsung,exynos5420-tmu-ext-triminfo";
- reg = <0x10068000 0x100>, <0x1006c000 0x4>;
- interrupts = <0 184 0>;
- clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
- clock-names = "tmu_apbif", "tmu_triminfo_apbif";
- #include "exynos4412-tmu-sensor-conf.dtsi"
- };
-
- tmu_cpu3: tmu@1006c000 {
- compatible = "samsung,exynos5420-tmu-ext-triminfo";
- reg = <0x1006c000 0x100>, <0x100a0000 0x4>;
- interrupts = <0 185 0>;
- clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
- clock-names = "tmu_apbif", "tmu_triminfo_apbif";
- #include "exynos4412-tmu-sensor-conf.dtsi"
- };
-
- tmu_gpu: tmu@100a0000 {
- compatible = "samsung,exynos5420-tmu-ext-triminfo";
- reg = <0x100a0000 0x100>, <0x10068000 0x4>;
- interrupts = <0 215 0>;
- clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
- clock-names = "tmu_apbif", "tmu_triminfo_apbif";
- #include "exynos4412-tmu-sensor-conf.dtsi"
- };
-
- thermal-zones {
- cpu0_thermal: cpu0-thermal {
- thermal-sensors = <&tmu_cpu0>;
- #include "exynos5420-trip-points.dtsi"
- };
- cpu1_thermal: cpu1-thermal {
- thermal-sensors = <&tmu_cpu1>;
- #include "exynos5420-trip-points.dtsi"
- };
- cpu2_thermal: cpu2-thermal {
- thermal-sensors = <&tmu_cpu2>;
- #include "exynos5420-trip-points.dtsi"
- };
- cpu3_thermal: cpu3-thermal {
- thermal-sensors = <&tmu_cpu3>;
- #include "exynos5420-trip-points.dtsi"
- };
- gpu_thermal: gpu-thermal {
- thermal-sensors = <&tmu_gpu>;
- #include "exynos5420-trip-points.dtsi"
+ i2s2: i2s@12D70000 {
+ compatible = "samsung,exynos5420-i2s";
+ reg = <0x12D70000 0x100>;
+ dmas = <&pdma0 12
+ &pdma0 11>;
+ dma-names = "tx", "rx";
+ clocks = <&clock CLK_I2S2>, <&clock CLK_SCLK_I2S2>;
+ clock-names = "iis", "i2s_opclk0";
+ #clock-cells = <1>;
+ clock-output-names = "i2s_cdclk2";
+ #sound-dai-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s2_bus>;
+ status = "disabled";
};
- };
- watchdog: watchdog@101D0000 {
- compatible = "samsung,exynos5420-wdt";
- reg = <0x101D0000 0x100>;
- interrupts = <0 42 0>;
- clocks = <&clock CLK_WDT>;
- clock-names = "watchdog";
- samsung,syscon-phandle = <&pmu_system_controller>;
- };
-
- sss: sss@10830000 {
- compatible = "samsung,exynos4210-secss";
- reg = <0x10830000 0x300>;
- interrupts = <0 112 0>;
- clocks = <&clock CLK_SSS>;
- clock-names = "secss";
- };
-
- usbdrd3_0: usb3-0 {
- compatible = "samsung,exynos5250-dwusb3";
- clocks = <&clock CLK_USBD300>;
- clock-names = "usbdrd30";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- usbdrd_dwc3_0: dwc3@12000000 {
- compatible = "snps,dwc3";
- reg = <0x12000000 0x10000>;
- interrupts = <0 72 0>;
- phys = <&usbdrd_phy0 0>, <&usbdrd_phy0 1>;
- phy-names = "usb2-phy", "usb3-phy";
+ spi_0: spi@12d20000 {
+ compatible = "samsung,exynos4210-spi";
+ reg = <0x12d20000 0x100>;
+ interrupts = <0 68 0>;
+ dmas = <&pdma0 5
+ &pdma0 4>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_bus>;
+ clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
+ clock-names = "spi", "spi_busclk0";
+ status = "disabled";
};
- };
-
- usbdrd_phy0: phy@12100000 {
- compatible = "samsung,exynos5420-usbdrd-phy";
- reg = <0x12100000 0x100>;
- clocks = <&clock CLK_USBD300>, <&clock CLK_SCLK_USBPHY300>;
- clock-names = "phy", "ref";
- samsung,pmu-syscon = <&pmu_system_controller>;
- #phy-cells = <1>;
- };
- usbdrd3_1: usb3-1 {
- compatible = "samsung,exynos5250-dwusb3";
- clocks = <&clock CLK_USBD301>;
- clock-names = "usbdrd30";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- usbdrd_dwc3_1: dwc3@12400000 {
- compatible = "snps,dwc3";
- reg = <0x12400000 0x10000>;
- interrupts = <0 73 0>;
- phys = <&usbdrd_phy1 0>, <&usbdrd_phy1 1>;
- phy-names = "usb2-phy", "usb3-phy";
+ spi_1: spi@12d30000 {
+ compatible = "samsung,exynos4210-spi";
+ reg = <0x12d30000 0x100>;
+ interrupts = <0 69 0>;
+ dmas = <&pdma1 5
+ &pdma1 4>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
+ clock-names = "spi", "spi_busclk0";
+ status = "disabled";
};
- };
-
- usbdrd_phy1: phy@12500000 {
- compatible = "samsung,exynos5420-usbdrd-phy";
- reg = <0x12500000 0x100>;
- clocks = <&clock CLK_USBD301>, <&clock CLK_SCLK_USBPHY301>;
- clock-names = "phy", "ref";
- samsung,pmu-syscon = <&pmu_system_controller>;
- #phy-cells = <1>;
- };
-
- usbhost2: usb@12110000 {
- compatible = "samsung,exynos4210-ehci";
- reg = <0x12110000 0x100>;
- interrupts = <0 71 0>;
- clocks = <&clock CLK_USBH20>;
- clock-names = "usbhost";
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- phys = <&usb2_phy 1>;
+ spi_2: spi@12d40000 {
+ compatible = "samsung,exynos4210-spi";
+ reg = <0x12d40000 0x100>;
+ interrupts = <0 70 0>;
+ dmas = <&pdma0 7
+ &pdma0 6>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_bus>;
+ clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
+ clock-names = "spi", "spi_busclk0";
+ status = "disabled";
};
- };
- usbhost1: usb@12120000 {
- compatible = "samsung,exynos4210-ohci";
- reg = <0x12120000 0x100>;
- interrupts = <0 71 0>;
-
- clocks = <&clock CLK_USBH20>;
- clock-names = "usbhost";
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- phys = <&usb2_phy 1>;
+ dp_phy: dp-video-phy {
+ compatible = "samsung,exynos5420-dp-video-phy";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ #phy-cells = <0>;
};
- };
-
- usb2_phy: phy@12130000 {
- compatible = "samsung,exynos5250-usb2-phy";
- reg = <0x12130000 0x100>;
- clocks = <&clock CLK_USBH20>, <&clock CLK_SCLK_USBPHY300>;
- clock-names = "phy", "ref";
- #phy-cells = <1>;
- samsung,sysreg-phandle = <&sysreg_system_controller>;
- samsung,pmureg-phandle = <&pmu_system_controller>;
- };
-
- sysmmu_g2dr: sysmmu@0x10A60000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x10A60000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <24 5>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_G2D>, <&clock CLK_G2D>;
- #iommu-cells = <0>;
- };
-
- sysmmu_g2dw: sysmmu@0x10A70000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x10A70000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <22 2>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_G2D>, <&clock CLK_G2D>;
- #iommu-cells = <0>;
- };
-
- sysmmu_tv: sysmmu@0x14650000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x14650000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <7 4>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MIXER>, <&clock CLK_MIXER>;
- power-domains = <&disp_pd>;
- #iommu-cells = <0>;
- };
-
- sysmmu_gscl0: sysmmu@0x13E80000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13E80000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <2 0>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>;
- power-domains = <&gsc_pd>;
- #iommu-cells = <0>;
- };
-
- sysmmu_gscl1: sysmmu@0x13E90000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x13E90000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <2 2>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_GSCL1>, <&clock CLK_GSCL1>;
- power-domains = <&gsc_pd>;
- #iommu-cells = <0>;
- };
-
- sysmmu_scaler0r: sysmmu@0x12880000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x12880000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <22 4>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MSCL0>, <&clock CLK_MSCL0>;
- #iommu-cells = <0>;
- };
-
- sysmmu_scaler1r: sysmmu@0x12890000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x12890000 0x1000>;
- interrupts = <0 186 0>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>;
- #iommu-cells = <0>;
- };
- sysmmu_scaler2r: sysmmu@0x128A0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x128A0000 0x1000>;
- interrupts = <0 188 0>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>;
- #iommu-cells = <0>;
- };
-
- sysmmu_scaler0w: sysmmu@0x128C0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x128C0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <27 2>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MSCL0>, <&clock CLK_MSCL0>;
- #iommu-cells = <0>;
- };
-
- sysmmu_scaler1w: sysmmu@0x128D0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x128D0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <22 6>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>;
- #iommu-cells = <0>;
- };
-
- sysmmu_scaler2w: sysmmu@0x128E0000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x128E0000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <19 6>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>;
- #iommu-cells = <0>;
- };
-
- sysmmu_rotator: sysmmu@0x11D40000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11D40000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <4 0>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_ROTATOR>, <&clock CLK_ROTATOR>;
- #iommu-cells = <0>;
- };
-
- sysmmu_jpeg0: sysmmu@0x11F10000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11F10000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <4 2>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_JPEG>, <&clock CLK_JPEG>;
- #iommu-cells = <0>;
- };
-
- sysmmu_jpeg1: sysmmu@0x11F20000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11F20000 0x1000>;
- interrupts = <0 169 0>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_JPEG2>, <&clock CLK_JPEG2>;
- #iommu-cells = <0>;
- };
-
- sysmmu_mfc_l: sysmmu@0x11200000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11200000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <6 2>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MFCL>, <&clock CLK_MFC>;
- power-domains = <&mfc_pd>;
- #iommu-cells = <0>;
- };
-
- sysmmu_mfc_r: sysmmu@0x11210000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x11210000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <8 5>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_MFCR>, <&clock CLK_MFC>;
- power-domains = <&mfc_pd>;
- #iommu-cells = <0>;
- };
-
- sysmmu_fimd1_0: sysmmu@0x14640000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x14640000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <3 2>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_FIMD1M0>, <&clock CLK_FIMD1>;
- power-domains = <&disp_pd>;
- #iommu-cells = <0>;
- };
-
- sysmmu_fimd1_1: sysmmu@0x14680000 {
- compatible = "samsung,exynos-sysmmu";
- reg = <0x14680000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <3 0>;
- clock-names = "sysmmu", "master";
- clocks = <&clock CLK_SMMU_FIMD1M1>, <&clock CLK_FIMD1>;
- power-domains = <&disp_pd>;
- #iommu-cells = <0>;
- };
-
- bus_wcore: bus_wcore {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK400_WCORE>;
- clock-names = "bus";
- operating-points-v2 = <&bus_wcore_opp_table>;
- status = "disabled";
- };
-
- bus_noc: bus_noc {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK100_NOC>;
- clock-names = "bus";
- operating-points-v2 = <&bus_noc_opp_table>;
- status = "disabled";
- };
-
- bus_fsys_apb: bus_fsys_apb {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_PCLK200_FSYS>;
- clock-names = "bus";
- operating-points-v2 = <&bus_fsys_apb_opp_table>;
- status = "disabled";
- };
-
- bus_fsys: bus_fsys {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK200_FSYS>;
- clock-names = "bus";
- operating-points-v2 = <&bus_fsys_apb_opp_table>;
- status = "disabled";
- };
-
- bus_fsys2: bus_fsys2 {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK200_FSYS2>;
- clock-names = "bus";
- operating-points-v2 = <&bus_fsys2_opp_table>;
- status = "disabled";
- };
-
- bus_mfc: bus_mfc {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK333>;
- clock-names = "bus";
- operating-points-v2 = <&bus_mfc_opp_table>;
- status = "disabled";
- };
-
- bus_gen: bus_gen {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK266>;
- clock-names = "bus";
- operating-points-v2 = <&bus_gen_opp_table>;
- status = "disabled";
- };
-
- bus_peri: bus_peri {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK66>;
- clock-names = "bus";
- operating-points-v2 = <&bus_peri_opp_table>;
- status = "disabled";
- };
-
- bus_g2d: bus_g2d {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK333_G2D>;
- clock-names = "bus";
- operating-points-v2 = <&bus_g2d_opp_table>;
- status = "disabled";
- };
-
- bus_g2d_acp: bus_g2d_acp {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK266_G2D>;
- clock-names = "bus";
- operating-points-v2 = <&bus_g2d_acp_opp_table>;
- status = "disabled";
- };
-
- bus_jpeg: bus_jpeg {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK300_JPEG>;
- clock-names = "bus";
- operating-points-v2 = <&bus_jpeg_opp_table>;
- status = "disabled";
- };
-
- bus_jpeg_apb: bus_jpeg_apb {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK166>;
- clock-names = "bus";
- operating-points-v2 = <&bus_jpeg_apb_opp_table>;
- status = "disabled";
- };
-
- bus_disp1_fimd: bus_disp1_fimd {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK300_DISP1>;
- clock-names = "bus";
- operating-points-v2 = <&bus_disp1_fimd_opp_table>;
- status = "disabled";
- };
-
- bus_disp1: bus_disp1 {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK400_DISP1>;
- clock-names = "bus";
- operating-points-v2 = <&bus_disp1_opp_table>;
- status = "disabled";
- };
-
- bus_gscl_scaler: bus_gscl_scaler {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK300_GSCL>;
- clock-names = "bus";
- operating-points-v2 = <&bus_gscl_opp_table>;
- status = "disabled";
- };
-
- bus_mscl: bus_mscl {
- compatible = "samsung,exynos-bus";
- clocks = <&clock CLK_DOUT_ACLK400_MSCL>;
- clock-names = "bus";
- operating-points-v2 = <&bus_mscl_opp_table>;
- status = "disabled";
- };
-
- bus_wcore_opp_table: opp_table2 {
- compatible = "operating-points-v2";
-
- opp00 {
- opp-hz = /bits/ 64 <84000000>;
- opp-microvolt = <925000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <111000000>;
- opp-microvolt = <950000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <222000000>;
- opp-microvolt = <950000>;
+ mipi_phy: mipi-video-phy {
+ compatible = "samsung,s5pv210-mipi-video-phy";
+ syscon = <&pmu_system_controller>;
+ #phy-cells = <1>;
};
- opp03 {
- opp-hz = /bits/ 64 <333000000>;
- opp-microvolt = <950000>;
- };
- opp04 {
- opp-hz = /bits/ 64 <400000000>;
- opp-microvolt = <987500>;
- };
- };
- bus_noc_opp_table: opp_table3 {
- compatible = "operating-points-v2";
-
- opp00 {
- opp-hz = /bits/ 64 <67000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <75000000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <86000000>;
- };
- opp03 {
- opp-hz = /bits/ 64 <100000000>;
+ dsi@14500000 {
+ compatible = "samsung,exynos5410-mipi-dsi";
+ reg = <0x14500000 0x10000>;
+ interrupts = <0 82 0>;
+ phys = <&mipi_phy 1>;
+ phy-names = "dsim";
+ clocks = <&clock CLK_DSIM1>, <&clock CLK_SCLK_MIPI1>;
+ clock-names = "bus_clk", "pll_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
};
- };
-
- bus_fsys_apb_opp_table: opp_table4 {
- compatible = "operating-points-v2";
- opp-shared;
- opp00 {
- opp-hz = /bits/ 64 <100000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <200000000>;
+ adc: adc@12D10000 {
+ compatible = "samsung,exynos-adc-v2";
+ reg = <0x12D10000 0x100>;
+ interrupts = <0 106 0>;
+ clocks = <&clock CLK_TSADC>;
+ clock-names = "adc";
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ status = "disabled";
};
- };
-
- bus_fsys2_opp_table: opp_table5 {
- compatible = "operating-points-v2";
- opp00 {
- opp-hz = /bits/ 64 <75000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <100000000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <150000000>;
+ hsi2c_8: i2c@12E00000 {
+ compatible = "samsung,exynos5250-hsi2c";
+ reg = <0x12E00000 0x1000>;
+ interrupts = <0 87 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c8_hs_bus>;
+ clocks = <&clock CLK_USI4>;
+ clock-names = "hsi2c";
+ status = "disabled";
};
- };
- bus_mfc_opp_table: opp_table6 {
- compatible = "operating-points-v2";
-
- opp00 {
- opp-hz = /bits/ 64 <96000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <111000000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <167000000>;
- };
- opp03 {
- opp-hz = /bits/ 64 <222000000>;
- };
- opp04 {
- opp-hz = /bits/ 64 <333000000>;
+ hsi2c_9: i2c@12E10000 {
+ compatible = "samsung,exynos5250-hsi2c";
+ reg = <0x12E10000 0x1000>;
+ interrupts = <0 88 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c9_hs_bus>;
+ clocks = <&clock CLK_USI5>;
+ clock-names = "hsi2c";
+ status = "disabled";
};
- };
- bus_gen_opp_table: opp_table7 {
- compatible = "operating-points-v2";
-
- opp00 {
- opp-hz = /bits/ 64 <89000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <133000000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <178000000>;
- };
- opp03 {
- opp-hz = /bits/ 64 <267000000>;
+ hsi2c_10: i2c@12E20000 {
+ compatible = "samsung,exynos5250-hsi2c";
+ reg = <0x12E20000 0x1000>;
+ interrupts = <0 203 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c10_hs_bus>;
+ clocks = <&clock CLK_USI6>;
+ clock-names = "hsi2c";
+ status = "disabled";
};
- };
-
- bus_peri_opp_table: opp_table8 {
- compatible = "operating-points-v2";
- opp00 {
- opp-hz = /bits/ 64 <67000000>;
+ hdmi: hdmi@14530000 {
+ compatible = "samsung,exynos5420-hdmi";
+ reg = <0x14530000 0x70000>;
+ interrupts = <0 95 0>;
+ clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+ <&clock CLK_DOUT_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+ <&clock CLK_MOUT_HDMI>;
+ clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
+ "sclk_hdmiphy", "mout_hdmi";
+ phy = <&hdmiphy>;
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ status = "disabled";
+ power-domains = <&disp_pd>;
+ };
+
+ hdmiphy: hdmiphy@145D0000 {
+ reg = <0x145D0000 0x20>;
+ };
+
+ mixer: mixer@14450000 {
+ compatible = "samsung,exynos5420-mixer";
+ reg = <0x14450000 0x10000>;
+ interrupts = <0 94 0>;
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>;
+ clock-names = "mixer", "hdmi", "sclk_hdmi";
+ power-domains = <&disp_pd>;
+ iommus = <&sysmmu_tv>;
+ };
+
+ rotator: rotator@11C00000 {
+ compatible = "samsung,exynos5250-rotator";
+ reg = <0x11C00000 0x64>;
+ interrupts = <0 84 0>;
+ clocks = <&clock CLK_ROTATOR>;
+ clock-names = "rotator";
+ iommus = <&sysmmu_rotator>;
+ };
+
+ gsc_0: video-scaler@13e00000 {
+ compatible = "samsung,exynos5-gsc";
+ reg = <0x13e00000 0x1000>;
+ interrupts = <0 85 0>;
+ clocks = <&clock CLK_GSCL0>;
+ clock-names = "gscl";
+ power-domains = <&gsc_pd>;
+ iommus = <&sysmmu_gscl0>;
+ };
+
+ gsc_1: video-scaler@13e10000 {
+ compatible = "samsung,exynos5-gsc";
+ reg = <0x13e10000 0x1000>;
+ interrupts = <0 86 0>;
+ clocks = <&clock CLK_GSCL1>;
+ clock-names = "gscl";
+ power-domains = <&gsc_pd>;
+ iommus = <&sysmmu_gscl1>;
+ };
+
+ jpeg_0: jpeg@11F50000 {
+ compatible = "samsung,exynos5420-jpeg";
+ reg = <0x11F50000 0x1000>;
+ interrupts = <0 89 0>;
+ clock-names = "jpeg";
+ clocks = <&clock CLK_JPEG>;
+ iommus = <&sysmmu_jpeg0>;
+ };
+
+ jpeg_1: jpeg@11F60000 {
+ compatible = "samsung,exynos5420-jpeg";
+ reg = <0x11F60000 0x1000>;
+ interrupts = <0 168 0>;
+ clock-names = "jpeg";
+ clocks = <&clock CLK_JPEG2>;
+ iommus = <&sysmmu_jpeg1>;
+ };
+
+ pmu_system_controller: system-controller@10040000 {
+ compatible = "samsung,exynos5420-pmu", "syscon";
+ reg = <0x10040000 0x5000>;
+ clock-names = "clkout16";
+ clocks = <&clock CLK_FIN_PLL>;
+ #clock-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
};
- };
-
- bus_g2d_opp_table: opp_table9 {
- compatible = "operating-points-v2";
- opp00 {
- opp-hz = /bits/ 64 <84000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <167000000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <222000000>;
- };
- opp03 {
- opp-hz = /bits/ 64 <300000000>;
- };
- opp04 {
- opp-hz = /bits/ 64 <333000000>;
+ tmu_cpu0: tmu@10060000 {
+ compatible = "samsung,exynos5420-tmu";
+ reg = <0x10060000 0x100>;
+ interrupts = <0 65 0>;
+ clocks = <&clock CLK_TMU>;
+ clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ tmu_cpu1: tmu@10064000 {
+ compatible = "samsung,exynos5420-tmu";
+ reg = <0x10064000 0x100>;
+ interrupts = <0 183 0>;
+ clocks = <&clock CLK_TMU>;
+ clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ tmu_cpu2: tmu@10068000 {
+ compatible = "samsung,exynos5420-tmu-ext-triminfo";
+ reg = <0x10068000 0x100>, <0x1006c000 0x4>;
+ interrupts = <0 184 0>;
+ clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
+ clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ tmu_cpu3: tmu@1006c000 {
+ compatible = "samsung,exynos5420-tmu-ext-triminfo";
+ reg = <0x1006c000 0x100>, <0x100a0000 0x4>;
+ interrupts = <0 185 0>;
+ clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
+ clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ tmu_gpu: tmu@100a0000 {
+ compatible = "samsung,exynos5420-tmu-ext-triminfo";
+ reg = <0x100a0000 0x100>, <0x10068000 0x4>;
+ interrupts = <0 215 0>;
+ clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
+ clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ sysmmu_g2dr: sysmmu@0x10A60000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x10A60000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <24 5>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_G2D>, <&clock CLK_G2D>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_g2dw: sysmmu@0x10A70000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x10A70000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <22 2>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_G2D>, <&clock CLK_G2D>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_tv: sysmmu@0x14650000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x14650000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <7 4>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MIXER>, <&clock CLK_MIXER>;
+ power-domains = <&disp_pd>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_gscl0: sysmmu@0x13E80000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13E80000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <2 0>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>;
+ power-domains = <&gsc_pd>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_gscl1: sysmmu@0x13E90000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13E90000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <2 2>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_GSCL1>, <&clock CLK_GSCL1>;
+ power-domains = <&gsc_pd>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_scaler0r: sysmmu@0x12880000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x12880000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <22 4>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MSCL0>, <&clock CLK_MSCL0>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_scaler1r: sysmmu@0x12890000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x12890000 0x1000>;
+ interrupts = <0 186 0>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_scaler2r: sysmmu@0x128A0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x128A0000 0x1000>;
+ interrupts = <0 188 0>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_scaler0w: sysmmu@0x128C0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x128C0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <27 2>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MSCL0>, <&clock CLK_MSCL0>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_scaler1w: sysmmu@0x128D0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x128D0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <22 6>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_scaler2w: sysmmu@0x128E0000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x128E0000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <19 6>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_rotator: sysmmu@0x11D40000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11D40000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <4 0>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_ROTATOR>, <&clock CLK_ROTATOR>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_jpeg0: sysmmu@0x11F10000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11F10000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <4 2>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_JPEG>, <&clock CLK_JPEG>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_jpeg1: sysmmu@0x11F20000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11F20000 0x1000>;
+ interrupts = <0 169 0>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_JPEG2>, <&clock CLK_JPEG2>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_mfc_l: sysmmu@0x11200000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11200000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <6 2>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MFCL>, <&clock CLK_MFC>;
+ power-domains = <&mfc_pd>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_mfc_r: sysmmu@0x11210000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x11210000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <8 5>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_MFCR>, <&clock CLK_MFC>;
+ power-domains = <&mfc_pd>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_fimd1_0: sysmmu@0x14640000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x14640000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <3 2>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_FIMD1M0>, <&clock CLK_FIMD1>;
+ power-domains = <&disp_pd>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_fimd1_1: sysmmu@0x14680000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x14680000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <3 0>;
+ clock-names = "sysmmu", "master";
+ clocks = <&clock CLK_SMMU_FIMD1M1>, <&clock CLK_FIMD1>;
+ power-domains = <&disp_pd>;
+ #iommu-cells = <0>;
+ };
+
+ bus_wcore: bus_wcore {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK400_WCORE>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_wcore_opp_table>;
+ status = "disabled";
};
- };
-
- bus_g2d_acp_opp_table: opp_table10 {
- compatible = "operating-points-v2";
- opp00 {
- opp-hz = /bits/ 64 <67000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <133000000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <178000000>;
- };
- opp03 {
- opp-hz = /bits/ 64 <267000000>;
+ bus_noc: bus_noc {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK100_NOC>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_noc_opp_table>;
+ status = "disabled";
};
- };
-
- bus_jpeg_opp_table: opp_table11 {
- compatible = "operating-points-v2";
- opp00 {
- opp-hz = /bits/ 64 <75000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <150000000>;
- };
- opp02 {
- opp-hz = /bits/ 64 <200000000>;
- };
- opp03 {
- opp-hz = /bits/ 64 <300000000>;
+ bus_fsys_apb: bus_fsys_apb {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_PCLK200_FSYS>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_fsys_apb_opp_table>;
+ status = "disabled";
};
- };
-
- bus_jpeg_apb_opp_table: opp_table12 {
- compatible = "operating-points-v2";
- opp00 {
- opp-hz = /bits/ 64 <84000000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <111000000>;
+ bus_fsys: bus_fsys {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK200_FSYS>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_fsys_apb_opp_table>;
+ status = "disabled";
};
- opp02 {
- opp-hz = /bits/ 64 <134000000>;
+
+ bus_fsys2: bus_fsys2 {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK200_FSYS2>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_fsys2_opp_table>;
+ status = "disabled";
};
- opp03 {
- opp-hz = /bits/ 64 <167000000>;
+
+ bus_mfc: bus_mfc {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK333>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_mfc_opp_table>;
+ status = "disabled";
};
- };
- bus_disp1_fimd_opp_table: opp_table13 {
- compatible = "operating-points-v2";
+ bus_gen: bus_gen {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK266>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_gen_opp_table>;
+ status = "disabled";
+ };
- opp00 {
- opp-hz = /bits/ 64 <120000000>;
+ bus_peri: bus_peri {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK66>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_peri_opp_table>;
+ status = "disabled";
};
- opp01 {
- opp-hz = /bits/ 64 <200000000>;
+
+ bus_g2d: bus_g2d {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK333_G2D>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_g2d_opp_table>;
+ status = "disabled";
};
- };
- bus_disp1_opp_table: opp_table14 {
- compatible = "operating-points-v2";
+ bus_g2d_acp: bus_g2d_acp {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK266_G2D>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_g2d_acp_opp_table>;
+ status = "disabled";
+ };
- opp00 {
- opp-hz = /bits/ 64 <120000000>;
+ bus_jpeg: bus_jpeg {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK300_JPEG>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_jpeg_opp_table>;
+ status = "disabled";
};
- opp01 {
- opp-hz = /bits/ 64 <200000000>;
+
+ bus_jpeg_apb: bus_jpeg_apb {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK166>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_jpeg_apb_opp_table>;
+ status = "disabled";
};
- opp02 {
- opp-hz = /bits/ 64 <300000000>;
+
+ bus_disp1_fimd: bus_disp1_fimd {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK300_DISP1>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_disp1_fimd_opp_table>;
+ status = "disabled";
};
- };
- bus_gscl_opp_table: opp_table15 {
- compatible = "operating-points-v2";
+ bus_disp1: bus_disp1 {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK400_DISP1>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_disp1_opp_table>;
+ status = "disabled";
+ };
- opp00 {
- opp-hz = /bits/ 64 <150000000>;
+ bus_gscl_scaler: bus_gscl_scaler {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK300_GSCL>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_gscl_opp_table>;
+ status = "disabled";
};
- opp01 {
- opp-hz = /bits/ 64 <200000000>;
+
+ bus_mscl: bus_mscl {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DOUT_ACLK400_MSCL>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_mscl_opp_table>;
+ status = "disabled";
};
- opp02 {
- opp-hz = /bits/ 64 <300000000>;
+
+ bus_wcore_opp_table: opp_table2 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <84000000>;
+ opp-microvolt = <925000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <111000000>;
+ opp-microvolt = <950000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <222000000>;
+ opp-microvolt = <950000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <333000000>;
+ opp-microvolt = <950000>;
+ };
+ opp04 {
+ opp-hz = /bits/ 64 <400000000>;
+ opp-microvolt = <987500>;
+ };
+ };
+
+ bus_noc_opp_table: opp_table3 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <67000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <75000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <86000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+ };
+
+ bus_fsys_apb_opp_table: opp_table4 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp00 {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <200000000>;
+ };
+ };
+
+ bus_fsys2_opp_table: opp_table5 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <75000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <150000000>;
+ };
+ };
+
+ bus_mfc_opp_table: opp_table6 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <96000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <111000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <167000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <222000000>;
+ };
+ opp04 {
+ opp-hz = /bits/ 64 <333000000>;
+ };
+ };
+
+ bus_gen_opp_table: opp_table7 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <89000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <133000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <178000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <267000000>;
+ };
+ };
+
+ bus_peri_opp_table: opp_table8 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <67000000>;
+ };
+ };
+
+ bus_g2d_opp_table: opp_table9 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <84000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <167000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <222000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <300000000>;
+ };
+ opp04 {
+ opp-hz = /bits/ 64 <333000000>;
+ };
+ };
+
+ bus_g2d_acp_opp_table: opp_table10 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <67000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <133000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <178000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <267000000>;
+ };
+ };
+
+ bus_jpeg_opp_table: opp_table11 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <75000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <150000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <200000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <300000000>;
+ };
+ };
+
+ bus_jpeg_apb_opp_table: opp_table12 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <84000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <111000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <134000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <167000000>;
+ };
+ };
+
+ bus_disp1_fimd_opp_table: opp_table13 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <120000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <200000000>;
+ };
+ };
+
+ bus_disp1_opp_table: opp_table14 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <120000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <200000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <300000000>;
+ };
+ };
+
+ bus_gscl_opp_table: opp_table15 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <150000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <200000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <300000000>;
+ };
+ };
+
+ bus_mscl_opp_table: opp_table16 {
+ compatible = "operating-points-v2";
+
+ opp00 {
+ opp-hz = /bits/ 64 <84000000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <167000000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <222000000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <333000000>;
+ };
+ opp04 {
+ opp-hz = /bits/ 64 <400000000>;
+ };
};
};
- bus_mscl_opp_table: opp_table16 {
- compatible = "operating-points-v2";
-
- opp00 {
- opp-hz = /bits/ 64 <84000000>;
+ thermal-zones {
+ cpu0_thermal: cpu0-thermal {
+ thermal-sensors = <&tmu_cpu0>;
+ #include "exynos5420-trip-points.dtsi"
};
- opp01 {
- opp-hz = /bits/ 64 <167000000>;
+ cpu1_thermal: cpu1-thermal {
+ thermal-sensors = <&tmu_cpu1>;
+ #include "exynos5420-trip-points.dtsi"
};
- opp02 {
- opp-hz = /bits/ 64 <222000000>;
+ cpu2_thermal: cpu2-thermal {
+ thermal-sensors = <&tmu_cpu2>;
+ #include "exynos5420-trip-points.dtsi"
};
- opp03 {
- opp-hz = /bits/ 64 <333000000>;
+ cpu3_thermal: cpu3-thermal {
+ thermal-sensors = <&tmu_cpu3>;
+ #include "exynos5420-trip-points.dtsi"
};
- opp04 {
- opp-hz = /bits/ 64 <400000000>;
+ gpu_thermal: gpu-thermal {
+ thermal-sensors = <&tmu_gpu>;
+ #include "exynos5420-trip-points.dtsi"
};
};
};
iommu-names = "m0", "m1";
};
+&i2c_0 {
+ clocks = <&clock CLK_I2C0>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+};
+
+&i2c_1 {
+ clocks = <&clock CLK_I2C1>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+};
+
+&i2c_2 {
+ clocks = <&clock CLK_I2C2>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
+
+&i2c_3 {
+ clocks = <&clock CLK_I2C3>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+};
+
+&hsi2c_4 {
+ clocks = <&clock CLK_USI0>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_hs_bus>;
+};
+
+&hsi2c_5 {
+ clocks = <&clock CLK_USI1>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_hs_bus>;
+};
+
+&hsi2c_6 {
+ clocks = <&clock CLK_USI2>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_hs_bus>;
+};
+
+&hsi2c_7 {
+ clocks = <&clock CLK_USI3>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_hs_bus>;
+};
+
+&mct {
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
+ clock-names = "fin_pll", "mct";
+};
+
+&pwm {
+ clocks = <&clock CLK_PWM>;
+ clock-names = "timers";
+};
+
&rtc {
clocks = <&clock CLK_RTC>;
clock-names = "rtc";
clock-names = "uart", "clk_uart_baud0";
};
+&sss {
+ clocks = <&clock CLK_SSS>;
+ clock-names = "secss";
+};
+
+&usbdrd3_0 {
+ clocks = <&clock CLK_USBD300>;
+ clock-names = "usbdrd30";
+};
+
+&usbdrd_phy0 {
+ clocks = <&clock CLK_USBD300>, <&clock CLK_SCLK_USBPHY300>;
+ clock-names = "phy", "ref";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+};
+
+&usbdrd3_1 {
+ clocks = <&clock CLK_USBD301>;
+ clock-names = "usbdrd30";
+};
+
+&usbdrd_dwc3_1 {
+ interrupts = <GIC_SPI 73 0>;
+};
+
+&usbdrd_phy1 {
+ clocks = <&clock CLK_USBD301>, <&clock CLK_SCLK_USBPHY301>;
+ clock-names = "phy", "ref";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+};
+
+&usbhost1 {
+ clocks = <&clock CLK_USBH20>;
+ clock-names = "usbhost";
+};
+
+&usbhost2 {
+ clocks = <&clock CLK_USBH20>;
+ clock-names = "usbhost";
+};
+
+&usb2_phy {
+ clocks = <&clock CLK_USBH20>, <&clock CLK_SCLK_USBPHY300>;
+ clock-names = "phy", "ref";
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ samsung,pmureg-phandle = <&pmu_system_controller>;
+};
+
+&watchdog {
+ clocks = <&clock CLK_WDT>;
+ clock-names = "watchdog";
+ samsung,syscon-phandle = <&pmu_system_controller>;
+};
+
#include "exynos5420-pinctrl.dtsi"
+++ /dev/null
-/*
- * Device tree sources for Exynos5422 thermal zone
- *
- * Copyright (c) 2015 Lukasz Majewski <l.majewski@samsung.com>
- * Anand Moon <linux.amoon@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <dt-bindings/thermal/thermal.h>
-
-/ {
- thermal-zones {
- cpu0_thermal: cpu0-thermal {
- thermal-sensors = <&tmu_cpu0 0>;
- polling-delay-passive = <250>;
- polling-delay = <0>;
- trips {
- cpu_alert0: cpu-alert-0 {
- temperature = <50000>; /* millicelsius */
- hysteresis = <5000>; /* millicelsius */
- type = "active";
- };
- cpu_alert1: cpu-alert-1 {
- temperature = <60000>; /* millicelsius */
- hysteresis = <5000>; /* millicelsius */
- type = "active";
- };
- cpu_alert2: cpu-alert-2 {
- temperature = <70000>; /* millicelsius */
- hysteresis = <5000>; /* millicelsius */
- type = "active";
- };
- cpu_crit0: cpu-crit-0 {
- temperature = <120000>; /* millicelsius */
- hysteresis = <0>; /* millicelsius */
- type = "critical";
- };
- /*
- * Exyunos542x support only 4 trip-points
- * so for these polling mode is required.
- * Start polling at temperature level of last
- * interrupt-driven trip: cpu_alert2
- */
- cpu_alert3: cpu-alert-3 {
- temperature = <70000>; /* millicelsius */
- hysteresis = <10000>; /* millicelsius */
- type = "passive";
- };
- cpu_alert4: cpu-alert-4 {
- temperature = <85000>; /* millicelsius */
- hysteresis = <10000>; /* millicelsius */
- type = "passive";
- };
-
- };
- cooling-maps {
- map0 {
- trip = <&cpu_alert0>;
- cooling-device = <&fan0 0 1>;
- };
- map1 {
- trip = <&cpu_alert1>;
- cooling-device = <&fan0 1 2>;
- };
- map2 {
- trip = <&cpu_alert2>;
- cooling-device = <&fan0 2 3>;
- };
- /*
- * When reaching cpu_alert3, reduce CPU
- * by 2 steps. On Exynos5422/5800 that would
- * be: 1500 MHz and 1100 MHz.
- */
- map3 {
- trip = <&cpu_alert3>;
- cooling-device = <&cpu0 0 2>;
- };
- map4 {
- trip = <&cpu_alert3>;
- cooling-device = <&cpu4 0 2>;
- };
-
- /*
- * When reaching cpu_alert4, reduce CPU
- * further, down to 600 MHz (11 steps for big,
- * 7 steps for LITTLE).
- */
- map5 {
- trip = <&cpu_alert4>;
- cooling-device = <&cpu0 3 7>;
- };
- map6 {
- trip = <&cpu_alert4>;
- cooling-device = <&cpu4 3 11>;
- };
- };
- };
- };
-};
/*
* Hardkernel Odroid XU3 board device tree source
*
- * Copyright (c) 2014 Collabora Ltd.
* Copyright (c) 2013 Samsung Electronics Co., Ltd.
* http://www.samsung.com
+ * Copyright (c) 2014 Collabora Ltd.
+ * Copyright (c) 2015 Lukasz Majewski <l.majewski@samsung.com>
+ * Anand Moon <linux.amoon@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
#include <dt-bindings/sound/samsung-i2s.h>
#include "exynos5800.dtsi"
#include "exynos5422-cpus.dtsi"
-#include "exynos5422-cpu-thermal.dtsi"
#include "exynos-mfc-reserved-memory.dtsi"
/ {
#cooling-cells = <2>;
cooling-levels = <0 130 170 230>;
};
+
+ thermal-zones {
+ cpu0_thermal: cpu0-thermal {
+ thermal-sensors = <&tmu_cpu0 0>;
+ polling-delay-passive = <250>;
+ polling-delay = <0>;
+ trips {
+ cpu_alert0: cpu-alert-0 {
+ temperature = <50000>; /* millicelsius */
+ hysteresis = <5000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_alert1: cpu-alert-1 {
+ temperature = <60000>; /* millicelsius */
+ hysteresis = <5000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_alert2: cpu-alert-2 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <5000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_crit0: cpu-crit-0 {
+ temperature = <120000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ /*
+ * Exynos542x supports only 4 trip-points
+ * so for these polling mode is required.
+ * Start polling at temperature level of last
+ * interrupt-driven trip: cpu_alert2
+ */
+ cpu_alert3: cpu-alert-3 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_alert4: cpu-alert-4 {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "passive";
+ };
+
+ };
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&fan0 0 1>;
+ };
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&fan0 1 2>;
+ };
+ map2 {
+ trip = <&cpu_alert2>;
+ cooling-device = <&fan0 2 3>;
+ };
+ /*
+ * When reaching cpu_alert3, reduce CPU
+ * by 2 steps. On Exynos5422/5800 that would
+ * be: 1600 MHz and 1100 MHz.
+ */
+ map3 {
+ trip = <&cpu_alert3>;
+ cooling-device = <&cpu0 0 2>;
+ };
+ map4 {
+ trip = <&cpu_alert3>;
+ cooling-device = <&cpu4 0 2>;
+ };
+
+ /*
+ * When reaching cpu_alert4, reduce CPU
+ * further, down to 600 MHz (11 steps for big,
+ * 7 steps for LITTLE).
+ */
+ map5 {
+ trip = <&cpu_alert4>;
+ cooling-device = <&cpu0 3 7>;
+ };
+ map6 {
+ trip = <&cpu_alert4>;
+ cooling-device = <&cpu4 3 11>;
+ };
+ };
+ };
+ };
};
&bus_wcore {
};
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
mmc-pwrseq = <&emmc_pwrseq>;
&tmu_cpu0 {
vtmu-supply = <&ldo7_reg>;
- status = "okay";
};
&tmu_cpu1 {
vtmu-supply = <&ldo7_reg>;
- status = "okay";
};
&tmu_cpu2 {
vtmu-supply = <&ldo7_reg>;
- status = "okay";
};
&tmu_cpu3 {
vtmu-supply = <&ldo7_reg>;
- status = "okay";
};
&tmu_gpu {
vtmu-supply = <&ldo7_reg>;
- status = "okay";
};
&rtc {
/dts-v1/;
#include "exynos5422-odroidxu3-common.dtsi"
#include "exynos5422-odroidxu3-audio.dtsi"
+#include "exynos54xx-odroidxu-leds.dtsi"
/ {
model = "Hardkernel Odroid XU3 Lite";
compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5";
-
- pwmleds {
- compatible = "pwm-leds";
-
- greenled {
- label = "green:mmc0";
- pwms = <&pwm 1 2000000 0>;
- pwm-names = "pwm1";
- /*
- * Green LED is much brighter than the others
- * so limit its max brightness
- */
- max_brightness = <127>;
- linux,default-trigger = "mmc0";
- };
-
- blueled {
- label = "blue:heartbeat";
- pwms = <&pwm 2 2000000 0>;
- pwm-names = "pwm2";
- max_brightness = <255>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- gpioleds {
- compatible = "gpio-leds";
- redled {
- label = "red:microSD";
- gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- linux,default-trigger = "mmc1";
- };
- };
};
&pwm {
/dts-v1/;
#include "exynos5422-odroidxu3-common.dtsi"
#include "exynos5422-odroidxu3-audio.dtsi"
+#include "exynos54xx-odroidxu-leds.dtsi"
/ {
model = "Hardkernel Odroid XU3";
compatible = "hardkernel,odroid-xu3", "samsung,exynos5800", "samsung,exynos5";
-
- pwmleds {
- compatible = "pwm-leds";
-
- greenled {
- label = "green:mmc0";
- pwms = <&pwm 1 2000000 0>;
- pwm-names = "pwm1";
- /*
- * Green LED is much brighter than the others
- * so limit its max brightness
- */
- max_brightness = <127>;
- linux,default-trigger = "mmc0";
- };
-
- blueled {
- label = "blue:heartbeat";
- pwms = <&pwm 2 2000000 0>;
- pwm-names = "pwm2";
- max_brightness = <255>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- gpioleds {
- compatible = "gpio-leds";
- redled {
- label = "red:microSD";
- gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- linux,default-trigger = "mmc1";
- };
- };
};
&i2c_0 {
--- /dev/null
+/*
+ * Hardkernel Odroid XU/XU3 LED device tree source
+ *
+ * Copyright (c) 2015,2016 Krzysztof Kozlowski
+ * Copyright (c) 2014 Collabora Ltd.
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ pwmleds {
+ compatible = "pwm-leds";
+
+ greenled {
+ label = "green:mmc0";
+ pwms = <&pwm 1 2000000 0>;
+ pwm-names = "pwm1";
+ /*
+ * Green LED is much brighter than the others
+ * so limit its max brightness
+ */
+ max_brightness = <127>;
+ linux,default-trigger = "mmc0";
+ };
+
+ blueled {
+ label = "blue:heartbeat";
+ pwms = <&pwm 2 2000000 0>;
+ pwm-names = "pwm2";
+ max_brightness = <255>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpioleds {
+ compatible = "gpio-leds";
+ redled {
+ label = "red:microSD";
+ gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "mmc1";
+ };
+ };
+};
--- /dev/null
+/*
+ * Samsung's Exynos54xx SoC series common device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2016 Krzysztof Kozlowski
+ *
+ * Device nodes common for Samsung Exynos5410/5420/5422/5800. Specific
+ * Exynos 54xx SoCs should include this file and customize it further
+ * (e.g. with clocks).
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "skeleton.dtsi"
+#include "exynos5.dtsi"
+
+/ {
+ compatible = "samsung,exynos5";
+
+ aliases {
+ i2c4 = &hsi2c_4;
+ i2c5 = &hsi2c_5;
+ i2c6 = &hsi2c_6;
+ i2c7 = &hsi2c_7;
+ usbdrdphy0 = &usbdrd_phy0;
+ usbdrdphy1 = &usbdrd_phy1;
+ };
+
+ soc: soc {
+ sysram@02020000 {
+ compatible = "mmio-sram";
+ reg = <0x02020000 0x54000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x02020000 0x54000>;
+
+ smp-sysram@0 {
+ compatible = "samsung,exynos4210-sysram";
+ reg = <0x0 0x1000>;
+ };
+
+ smp-sysram@53000 {
+ compatible = "samsung,exynos4210-sysram-ns";
+ reg = <0x53000 0x1000>;
+ };
+ };
+
+ mct: mct@101c0000 {
+ compatible = "samsung,exynos4210-mct";
+ reg = <0x101c0000 0xb00>;
+ interrupt-parent = <&mct_map>;
+ interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>,
+ <8>, <9>, <10>, <11>;
+
+ mct_map: mct-map {
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = <0 &combiner 23 3>,
+ <1 &combiner 23 4>,
+ <2 &combiner 25 2>,
+ <3 &combiner 25 3>,
+ <4 &gic 0 120 0>,
+ <5 &gic 0 121 0>,
+ <6 &gic 0 122 0>,
+ <7 &gic 0 123 0>,
+ <8 &gic 0 128 0>,
+ <9 &gic 0 129 0>,
+ <10 &gic 0 130 0>,
+ <11 &gic 0 131 0>;
+ };
+ };
+
+ watchdog: watchdog@101d0000 {
+ compatible = "samsung,exynos5420-wdt";
+ reg = <0x101d0000 0x100>;
+ interrupts = <0 42 0>;
+ };
+
+ sss: sss@10830000 {
+ compatible = "samsung,exynos4210-secss";
+ reg = <0x10830000 0x300>;
+ interrupts = <0 112 0>;
+ };
+
+ /* i2c_0-3 are defined in exynos5.dtsi */
+ hsi2c_4: i2c@12ca0000 {
+ compatible = "samsung,exynos5250-hsi2c";
+ reg = <0x12ca0000 0x1000>;
+ interrupts = <0 60 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ hsi2c_5: i2c@12cb0000 {
+ compatible = "samsung,exynos5250-hsi2c";
+ reg = <0x12cb0000 0x1000>;
+ interrupts = <0 61 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ hsi2c_6: i2c@12cc0000 {
+ compatible = "samsung,exynos5250-hsi2c";
+ reg = <0x12cc0000 0x1000>;
+ interrupts = <0 62 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ hsi2c_7: i2c@12cd0000 {
+ compatible = "samsung,exynos5250-hsi2c";
+ reg = <0x12cd0000 0x1000>;
+ interrupts = <0 63 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usbdrd3_0: usb3-0 {
+ compatible = "samsung,exynos5250-dwusb3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbdrd_dwc3_0: dwc3@12000000 {
+ compatible = "snps,dwc3";
+ reg = <0x12000000 0x10000>;
+ interrupts = <0 72 0>;
+ phys = <&usbdrd_phy0 0>, <&usbdrd_phy0 1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ usbdrd_phy0: phy@12100000 {
+ compatible = "samsung,exynos5420-usbdrd-phy";
+ reg = <0x12100000 0x100>;
+ #phy-cells = <1>;
+ };
+
+ usbdrd3_1: usb3-1 {
+ compatible = "samsung,exynos5250-dwusb3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbdrd_dwc3_1: dwc3@12400000 {
+ compatible = "snps,dwc3";
+ reg = <0x12400000 0x10000>;
+ phys = <&usbdrd_phy1 0>, <&usbdrd_phy1 1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ usbdrd_phy1: phy@12500000 {
+ compatible = "samsung,exynos5420-usbdrd-phy";
+ reg = <0x12500000 0x100>;
+ #phy-cells = <1>;
+ };
+
+ usbhost2: usb@12110000 {
+ compatible = "samsung,exynos4210-ehci";
+ reg = <0x12110000 0x100>;
+ interrupts = <0 71 0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phys = <&usb2_phy 1>;
+ };
+ };
+
+ usbhost1: usb@12120000 {
+ compatible = "samsung,exynos4210-ohci";
+ reg = <0x12120000 0x100>;
+ interrupts = <0 71 0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phys = <&usb2_phy 1>;
+ };
+ };
+
+ usb2_phy: phy@12130000 {
+ compatible = "samsung,exynos5250-usb2-phy";
+ reg = <0x12130000 0x100>;
+ #phy-cells = <1>;
+ };
+ };
+};
regulator-name = "vdd_1v2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
regulator-name = "vdd_1v35";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-name = "vdd_2v";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-name = "vdd_1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-name = "vdd_ldo9";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-always-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-mode = <MAX77802_OPMODE_LP>;
regulator-name = "vdd_ldo10";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-always-on;
regulator-state-mem {
regulator-off-in-suspend;
};
status = "okay";
};
-&mfc {
- memory-region = <&mfc_left>, <&mfc_right>;
-};
-
&mmc_0 {
status = "okay";
num-slots = <1>;
status = "okay";
};
+&tmu_cpu0 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu1 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu2 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu3 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_gpu {
+ vtmu-supply = <&ldo10_reg>;
+};
+
&usbdrd_dwc3_0 {
dr_mode = "host";
};
/ {
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <6000000>;
- };
-
main_xtal {
clock-frequency = <6000000>;
};
--- /dev/null
+/*
+ * Copyright (c) 2015 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/dts-v1/;
+#include "hi3519.dtsi"
+
+/ {
+ model = "HiSilicon HI3519 DEMO Board";
+ compatible = "hisilicon,hi3519";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&dual_timer0 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (c) 2015 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include <dt-bindings/clock/hi3519-clock.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ chosen { };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0>;
+ };
+ };
+
+ gic: interrupt-controller@10300000 {
+ compatible = "arm,cortex-a7-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x10301000 0x1000>, <0x10302000 0x1000>;
+ };
+
+ clk_3m: clk_3m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <3000000>;
+ };
+
+ crg: clock-reset-controller@12010000 {
+ compatible = "hisilicon,hi3519-crg";
+ #clock-cells = <1>;
+ #reset-cells = <2>;
+ reg = <0x12010000 0x10000>;
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ uart0: serial@12100000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x12100000 0x1000>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_UART0_CLK>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ uart1: serial@12101000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x12101000 0x1000>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_UART1_CLK>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ uart2: serial@12102000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x12102000 0x1000>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_UART2_CLK>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ uart3: serial@12103000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x12103000 0x1000>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_UART3_CLK>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ uart4: serial@12104000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x12104000 0x1000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_UART4_CLK>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ dual_timer0: timer@12000000 {
+ compatible = "arm,sp804", "arm,primecell";
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x12000000 0x1000>;
+ clocks = <&clk_3m>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ dual_timer1: timer@12001000 {
+ compatible = "arm,sp804", "arm,primecell";
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x12001000 0x1000>;
+ clocks = <&clk_3m>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ dual_timer2: timer@12002000 {
+ compatible = "arm,sp804", "arm,primecell";
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x12002000 0x1000>;
+ clocks = <&clk_3m>;
+ clock-names = "apb_pclk";
+ status = "disable";
+ };
+
+ spi_bus0: spi@12120000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x12120000 0x1000>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_SPI0_CLK>;
+ clock-names = "apb_pclk";
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
+ };
+
+ spi_bus1: spi@12121000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x12121000 0x1000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_SPI1_CLK>;
+ clock-names = "apb_pclk";
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
+ };
+
+ spi_bus2: spi@12122000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x12122000 0x1000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HI3519_SPI2_CLK>;
+ clock-names = "apb_pclk";
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
+ };
+
+ sysctrl: system-controller@12020000 {
+ compatible = "hisilicon,hi3519-sysctrl", "syscon";
+ reg = <0x12020000 0x1000>;
+ };
+
+ reboot {
+ compatible = "syscon-reboot";
+ regmap = <&sysctrl>;
+ offset = <0x4>;
+ mask = <0xdeadbeef>;
+ };
+ };
+};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
--- /dev/null
+/*
+ * Copyright (C) 2013-2016 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx23.dtsi"
+
+/ {
+ model = "SanDisk Sansa Fuze+";
+ compatible = "sandisk,sansa_fuze_plus", "fsl,imx23";
+
+ memory {
+ reg = <0x40000000 0x04000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx23-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd0>;
+ cd-inverted;
+ status = "okay";
+ };
+
+ ssp1: ssp@80034000 {
+ compatible = "fsl,imx23-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_8bit_pins_a>;
+ bus-width = <8>;
+ vmmc-supply = <®_vddio_sd1>;
+ non-removable;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX23_PAD_GPMI_D08__GPIO_0_8
+ MX23_PAD_PWM3__GPIO_1_29
+ MX23_PAD_AUART1_RTS__GPIO_0_27
+ MX23_PAD_AUART1_CTS__GPIO_0_26
+ MX23_PAD_I2C_SCL__I2C_SCL
+ MX23_PAD_I2C_SDA__I2C_SDA
+ MX23_PAD_LCD_DOTCK__GPIO_1_22
+ MX23_PAD_LCD_HSYNC__GPIO_1_24
+ MX23_PAD_PWM3__GPIO_1_29
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+ };
+ };
+
+ apbx@80040000 {
+ pwm: pwm@80064000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+ };
+
+ duart: serial@80070000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+
+ lradc@80050000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ dr_mode = "peripheral";
+ status = "okay";
+ };
+ };
+
+ reg_vddio_sd0: regulator-vddio-sd0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio-sd0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio0 8 0>;
+ };
+
+ reg_vddio_sd1: regulator-vddio-sd1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio-sd1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 29 0>;
+ };
+
+ reg_vdd_touchpad: regulator-vdd-touchpad0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-touchpad0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio0 26 0>;
+ regulator-always-on;
+ enable-active-low;
+ };
+
+ reg_vdd_tuner: regulator-vdd-tuner0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-tuner0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio0 29 0>;
+ regulator-always-on;
+ enable-active-low;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 2 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+
+ i2c-0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ gpios = <
+ &gpio1 24 0 /* SDA */
+ &gpio1 22 0 /* SCL */
+ >;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ };
+
+ i2c-1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ gpios = <
+ &gpio0 31 0 /* SDA */
+ &gpio0 30 0 /* SCL */
+ >;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+
+ touch: touch@20 {
+ compatible = "synaptics,synaptics_i2c";
+ reg = <0x20>;
+ };
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
+ };
+
+};
--- /dev/null
+/*
+ * Copyright (C) 2013-2016 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx23.dtsi"
+
+/ {
+ model = "Creative ZEN X-Fi3";
+ compatible = "creative,x-fi3", "fsl,imx23";
+
+ memory {
+ reg = <0x40000000 0x04000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx23-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd0>;
+ cd-inverted;
+ status = "okay";
+ };
+
+ ssp1: ssp@80034000 {
+ compatible = "fsl,imx23-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_4bit_pins_a>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX23_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ key_pins_a: keys@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX23_PAD_ROTARYA__GPIO_2_7
+ MX23_PAD_ROTARYB__GPIO_2_8
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+ };
+ };
+
+ apbx@80040000 {
+ i2c: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_pins_a>;
+ status = "okay";
+ };
+
+ pwm: pwm@80064000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+ };
+
+ duart: serial@80070000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ auart1: serial@8006e000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart1_2pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+
+ lradc@80050000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ dr_mode = "peripheral";
+ status = "okay";
+ };
+ };
+
+ reg_vddio_sd0: regulator-vddio-sd0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio-sd0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio0 7 0>;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 2 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key_pins_a>;
+
+ voldown {
+ label = "volume-down";
+ linux,code = <114>;
+ gpios = <&gpio2 7 0>;
+ debounce-interval = <20>;
+ };
+
+ volup {
+ label = "volume-up";
+ linux,code = <115>;
+ gpios = <&gpio2 8 0>;
+ debounce-interval = <20>;
+ };
+ };
+};
gpio0: gpio@0 {
compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+ reg = <0>;
interrupts = <16>;
gpio-controller;
#gpio-cells = <2>;
gpio1: gpio@1 {
compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+ reg = <1>;
interrupts = <17>;
gpio-controller;
#gpio-cells = <2>;
gpio2: gpio@2 {
compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+ reg = <2>;
interrupts = <18>;
gpio-controller;
#gpio-cells = <2>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
+ auart1_2pins_a: auart1-2pins@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX23_PAD_GPMI_D14__AUART2_RX
+ MX23_PAD_GPMI_D15__AUART2_TX
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
gpmi_pins_a: gpmi-nand@0 {
reg = <0>;
fsl,pinmux-ids = <
fsl,pull-up = <MXS_PULL_DISABLE>;
};
+ mmc1_4bit_pins_a: mmc1-4bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX23_PAD_GPMI_D00__SSP2_DATA0
+ MX23_PAD_GPMI_D01__SSP2_DATA1
+ MX23_PAD_GPMI_D02__SSP2_DATA2
+ MX23_PAD_GPMI_D03__SSP2_DATA3
+ MX23_PAD_GPMI_RDY1__SSP2_CMD
+ MX23_PAD_GPMI_WRN__SSP2_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ mmc1_8bit_pins_a: mmc1-8bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX23_PAD_GPMI_D00__SSP2_DATA0
+ MX23_PAD_GPMI_D01__SSP2_DATA1
+ MX23_PAD_GPMI_D02__SSP2_DATA2
+ MX23_PAD_GPMI_D03__SSP2_DATA3
+ MX23_PAD_GPMI_D04__SSP2_DATA4
+ MX23_PAD_GPMI_D05__SSP2_DATA5
+ MX23_PAD_GPMI_D06__SSP2_DATA6
+ MX23_PAD_GPMI_D07__SSP2_DATA7
+ MX23_PAD_GPMI_RDY1__SSP2_CMD
+ MX23_PAD_GPMI_WRN__SSP2_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
pwm2_pins_a: pwm2@0 {
reg = <0>;
fsl,pinmux-ids = <
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
#define MX25_PAD_A13__GPIO_4_1 0x00c 0x22C 0x000 0x05 0x000
#define MX25_PAD_A13__LCDC_CLS 0x00c 0x22C 0x000 0x07 0x000
-#define MX25_PAD_A14__A14 0x010 0x230 0x000 0x10 0x000
-#define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x15 0x000
-#define MX25_PAD_A14__SIM1_CLK1 0x010 0x230 0x000 0x16 0x000
-#define MX25_PAD_A14__LCDC_SPL 0x010 0x230 0x000 0x17 0x000
-
-#define MX25_PAD_A15__A15 0x014 0x234 0x000 0x10 0x000
-#define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x15 0x000
-#define MX25_PAD_A15__SIM1_RST1 0x014 0x234 0x000 0x16 0x000
-#define MX25_PAD_A15__LCDC_PS 0x014 0x234 0x000 0x17 0x000
-
-#define MX25_PAD_A16__A16 0x018 0x000 0x000 0x10 0x000
-#define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x15 0x000
-#define MX25_PAD_A16__SIM1_VEN1 0x018 0x000 0x000 0x16 0x000
-#define MX25_PAD_A16__LCDC_REV 0x018 0x000 0x000 0x17 0x000
-
-#define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x10 0x000
-#define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x15 0x000
-#define MX25_PAD_A17__SIM1_TX 0x01c 0x238 0x554 0x16 0x000
-#define MX25_PAD_A17__FEC_TX_ERR 0x01c 0x238 0x000 0x17 0x000
-
-#define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x10 0x000
-#define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x15 0x000
-#define MX25_PAD_A18__SIM1_PD1 0x020 0x23c 0x550 0x16 0x000
-#define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x17 0x000
-
-#define MX25_PAD_A19__A19 0x024 0x240 0x000 0x10 0x000
-#define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x15 0x000
-#define MX25_PAD_A19__SIM1_RX1 0x024 0x240 0x54c 0x16 0x000
-#define MX25_PAD_A19__FEC_RX_ERR 0x024 0x240 0x518 0x17 0x000
-
-#define MX25_PAD_A20__A20 0x028 0x244 0x000 0x10 0x000
-#define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x15 0x000
-#define MX25_PAD_A20__SIM2_CLK1 0x028 0x244 0x000 0x16 0x000
-#define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x17 0x000
-
-#define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x10 0x000
-#define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x15 0x000
-#define MX25_PAD_A21__SIM2_RST1 0x02c 0x248 0x000 0x16 0x000
-#define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x17 0x000
-
-#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x10 0x000
-#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x15 0x000
-#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000
-#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x16 0x000
-#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000
-
-#define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x10 0x000
-#define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x15 0x000
-#define MX25_PAD_A23__SIM2_TX1 0x034 0x24c 0x560 0x16 0x000
-#define MX25_PAD_A23__FEC_TDATA3 0x034 0x24c 0x000 0x17 0x000
-
-#define MX25_PAD_A24__A24 0x038 0x250 0x000 0x10 0x000
-#define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x15 0x000
-#define MX25_PAD_A24__SIM2_PD1 0x038 0x250 0x55c 0x16 0x000
-#define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x17 0x000
-
-#define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x10 0x000
-#define MX25_PAD_A25__GPIO_2_11 0x03c 0x254 0x000 0x15 0x000
-#define MX25_PAD_A25__FEC_CRS 0x03c 0x254 0x508 0x17 0x000
-
-#define MX25_PAD_EB0__EB0 0x040 0x258 0x000 0x10 0x000
-#define MX25_PAD_EB0__AUD4_TXD 0x040 0x258 0x464 0x14 0x000
-#define MX25_PAD_EB0__GPIO_2_12 0x040 0x258 0x000 0x15 0x000
-
-#define MX25_PAD_EB1__EB1 0x044 0x25c 0x000 0x10 0x000
-#define MX25_PAD_EB1__AUD4_RXD 0x044 0x25c 0x460 0x14 0x000
-#define MX25_PAD_EB1__GPIO_2_13 0x044 0x25c 0x000 0x15 0x000
-
-#define MX25_PAD_OE__OE 0x048 0x260 0x000 0x10 0x000
-#define MX25_PAD_OE__AUD4_TXC 0x048 0x260 0x000 0x14 0x000
-#define MX25_PAD_OE__GPIO_2_14 0x048 0x260 0x000 0x15 0x000
+#define MX25_PAD_A14__A14 0x010 0x230 0x000 0x00 0x000
+#define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x05 0x000
+#define MX25_PAD_A14__SIM1_CLK1 0x010 0x230 0x000 0x06 0x000
+#define MX25_PAD_A14__LCDC_SPL 0x010 0x230 0x000 0x07 0x000
+
+#define MX25_PAD_A15__A15 0x014 0x234 0x000 0x00 0x000
+#define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x05 0x000
+#define MX25_PAD_A15__SIM1_RST1 0x014 0x234 0x000 0x06 0x000
+#define MX25_PAD_A15__LCDC_PS 0x014 0x234 0x000 0x07 0x000
+
+#define MX25_PAD_A16__A16 0x018 0x000 0x000 0x00 0x000
+#define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x05 0x000
+#define MX25_PAD_A16__SIM1_VEN1 0x018 0x000 0x000 0x06 0x000
+#define MX25_PAD_A16__LCDC_REV 0x018 0x000 0x000 0x07 0x000
+
+#define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x00 0x000
+#define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x05 0x000
+#define MX25_PAD_A17__SIM1_TX 0x01c 0x238 0x554 0x06 0x000
+#define MX25_PAD_A17__FEC_TX_ERR 0x01c 0x238 0x000 0x07 0x000
+
+#define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x00 0x000
+#define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x05 0x000
+#define MX25_PAD_A18__SIM1_PD1 0x020 0x23c 0x550 0x06 0x000
+#define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x07 0x000
+
+#define MX25_PAD_A19__A19 0x024 0x240 0x000 0x00 0x000
+#define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x05 0x000
+#define MX25_PAD_A19__SIM1_RX1 0x024 0x240 0x54c 0x06 0x000
+#define MX25_PAD_A19__FEC_RX_ERR 0x024 0x240 0x518 0x07 0x000
+
+#define MX25_PAD_A20__A20 0x028 0x244 0x000 0x00 0x000
+#define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x05 0x000
+#define MX25_PAD_A20__SIM2_CLK1 0x028 0x244 0x000 0x06 0x000
+#define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x07 0x000
+
+#define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x00 0x000
+#define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x05 0x000
+#define MX25_PAD_A21__SIM2_RST1 0x02c 0x248 0x000 0x06 0x000
+#define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x07 0x000
+
+#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x00 0x000
+#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x05 0x000
+#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
+#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x06 0x000
+#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
+
+#define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x00 0x000
+#define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x05 0x000
+#define MX25_PAD_A23__SIM2_TX1 0x034 0x24c 0x560 0x06 0x000
+#define MX25_PAD_A23__FEC_TDATA3 0x034 0x24c 0x000 0x07 0x000
+
+#define MX25_PAD_A24__A24 0x038 0x250 0x000 0x00 0x000
+#define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x05 0x000
+#define MX25_PAD_A24__SIM2_PD1 0x038 0x250 0x55c 0x06 0x000
+#define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x07 0x000
+
+#define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x00 0x000
+#define MX25_PAD_A25__GPIO_2_11 0x03c 0x254 0x000 0x05 0x000
+#define MX25_PAD_A25__FEC_CRS 0x03c 0x254 0x508 0x07 0x000
+
+#define MX25_PAD_EB0__EB0 0x040 0x258 0x000 0x00 0x000
+#define MX25_PAD_EB0__AUD4_TXD 0x040 0x258 0x464 0x04 0x000
+#define MX25_PAD_EB0__GPIO_2_12 0x040 0x258 0x000 0x05 0x000
+
+#define MX25_PAD_EB1__EB1 0x044 0x25c 0x000 0x00 0x000
+#define MX25_PAD_EB1__AUD4_RXD 0x044 0x25c 0x460 0x04 0x000
+#define MX25_PAD_EB1__GPIO_2_13 0x044 0x25c 0x000 0x05 0x000
+
+#define MX25_PAD_OE__OE 0x048 0x260 0x000 0x00 0x000
+#define MX25_PAD_OE__AUD4_TXC 0x048 0x260 0x000 0x04 0x000
+#define MX25_PAD_OE__GPIO_2_14 0x048 0x260 0x000 0x05 0x000
#define MX25_PAD_CS0__CS0 0x04c 0x000 0x000 0x00 0x000
#define MX25_PAD_CS0__GPIO_4_2 0x04c 0x000 0x000 0x05 0x000
#define MX25_PAD_CS1__NF_CE3 0x050 0x000 0x000 0x01 0x000
#define MX25_PAD_CS1__GPIO_4_3 0x050 0x000 0x000 0x05 0x000
-#define MX25_PAD_CS4__CS4 0x054 0x264 0x000 0x10 0x000
+#define MX25_PAD_CS4__CS4 0x054 0x264 0x000 0x00 0x000
#define MX25_PAD_CS4__NF_CE1 0x054 0x264 0x000 0x01 0x000
-#define MX25_PAD_CS4__UART5_CTS 0x054 0x264 0x000 0x13 0x000
-#define MX25_PAD_CS4__GPIO_3_20 0x054 0x264 0x000 0x15 0x000
+#define MX25_PAD_CS4__UART5_CTS 0x054 0x264 0x000 0x03 0x000
+#define MX25_PAD_CS4__GPIO_3_20 0x054 0x264 0x000 0x05 0x000
#define MX25_PAD_CS5__CS5 0x058 0x268 0x000 0x00 0x000
#define MX25_PAD_CS5__NF_CE2 0x058 0x268 0x000 0x01 0x000
#define MX25_PAD_CS5__UART5_RTS 0x058 0x268 0x574 0x03 0x000
#define MX25_PAD_CS5__GPIO_3_21 0x058 0x268 0x000 0x05 0x000
-#define MX25_PAD_NF_CE0__NF_CE0 0x05c 0x26c 0x000 0x10 0x000
-#define MX25_PAD_NF_CE0__GPIO_3_22 0x05c 0x26c 0x000 0x15 0x000
+#define MX25_PAD_NF_CE0__NF_CE0 0x05c 0x26c 0x000 0x00 0x000
+#define MX25_PAD_NF_CE0__GPIO_3_22 0x05c 0x26c 0x000 0x05 0x000
-#define MX25_PAD_ECB__ECB 0x060 0x270 0x000 0x10 0x000
-#define MX25_PAD_ECB__UART5_TXD 0x060 0x270 0x000 0x13 0x000
-#define MX25_PAD_ECB__GPIO_3_23 0x060 0x270 0x000 0x15 0x000
+#define MX25_PAD_ECB__ECB 0x060 0x270 0x000 0x00 0x000
+#define MX25_PAD_ECB__UART5_TXD 0x060 0x270 0x000 0x03 0x000
+#define MX25_PAD_ECB__GPIO_3_23 0x060 0x270 0x000 0x05 0x000
-#define MX25_PAD_LBA__LBA 0x064 0x274 0x000 0x10 0x000
-#define MX25_PAD_LBA__UART5_RXD 0x064 0x274 0x578 0x13 0x000
-#define MX25_PAD_LBA__GPIO_3_24 0x064 0x274 0x000 0x15 0x000
+#define MX25_PAD_LBA__LBA 0x064 0x274 0x000 0x00 0x000
+#define MX25_PAD_LBA__UART5_RXD 0x064 0x274 0x578 0x03 0x000
+#define MX25_PAD_LBA__GPIO_3_24 0x064 0x274 0x000 0x05 0x000
#define MX25_PAD_BCLK__BCLK 0x068 0x000 0x000 0x00 0x000
#define MX25_PAD_BCLK__GPIO_4_4 0x068 0x000 0x000 0x05 0x000
-#define MX25_PAD_RW__RW 0x06c 0x278 0x000 0x10 0x000
-#define MX25_PAD_RW__AUD4_TXFS 0x06c 0x278 0x474 0x14 0x000
-#define MX25_PAD_RW__GPIO_3_25 0x06c 0x278 0x000 0x15 0x000
+#define MX25_PAD_RW__RW 0x06c 0x278 0x000 0x00 0x000
+#define MX25_PAD_RW__AUD4_TXFS 0x06c 0x278 0x474 0x04 0x000
+#define MX25_PAD_RW__GPIO_3_25 0x06c 0x278 0x000 0x05 0x000
-#define MX25_PAD_NFWE_B__NFWE_B 0x070 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFWE_B__GPIO_3_26 0x070 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFWE_B__NFWE_B 0x070 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFWE_B__GPIO_3_26 0x070 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFRE_B__NFRE_B 0x074 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFRE_B__GPIO_3_27 0x074 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFRE_B__NFRE_B 0x074 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFRE_B__GPIO_3_27 0x074 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFALE__NFALE 0x078 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFALE__GPIO_3_28 0x078 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFALE__NFALE 0x078 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFALE__GPIO_3_28 0x078 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFCLE__NFCLE 0x07c 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFCLE__GPIO_3_29 0x07c 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFCLE__NFCLE 0x07c 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFCLE__GPIO_3_29 0x07c 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFWP_B__NFWP_B 0x080 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFWP_B__GPIO_3_30 0x080 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFWP_B__NFWP_B 0x080 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFWP_B__GPIO_3_30 0x080 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFRB__NFRB 0x084 0x27c 0x000 0x10 0x000
-#define MX25_PAD_NFRB__GPIO_3_31 0x084 0x27c 0x000 0x15 0x000
+#define MX25_PAD_NFRB__NFRB 0x084 0x27c 0x000 0x00 0x000
+#define MX25_PAD_NFRB__GPIO_3_31 0x084 0x27c 0x000 0x05 0x000
#define MX25_PAD_D15__D15 0x088 0x280 0x000 0x00 0x000
#define MX25_PAD_D15__LD16 0x088 0x280 0x000 0x01 0x000
#define MX25_PAD_D0__D0 0x0c4 0x2bc 0x000 0x00 0x000
#define MX25_PAD_D0__GPIO_4_20 0x0c4 0x2bc 0x000 0x05 0x000
-#define MX25_PAD_LD0__LD0 0x0c8 0x2c0 0x000 0x10 0x000
-#define MX25_PAD_LD0__CSI_D0 0x0c8 0x2c0 0x488 0x12 0x000
-#define MX25_PAD_LD0__GPIO_2_15 0x0c8 0x2c0 0x000 0x15 0x000
+#define MX25_PAD_LD0__LD0 0x0c8 0x2c0 0x000 0x00 0x000
+#define MX25_PAD_LD0__CSI_D0 0x0c8 0x2c0 0x488 0x02 0x000
+#define MX25_PAD_LD0__GPIO_2_15 0x0c8 0x2c0 0x000 0x05 0x000
-#define MX25_PAD_LD1__LD1 0x0cc 0x2c4 0x000 0x10 0x000
-#define MX25_PAD_LD1__CSI_D1 0x0cc 0x2c4 0x48c 0x12 0x000
-#define MX25_PAD_LD1__GPIO_2_16 0x0cc 0x2c4 0x000 0x15 0x000
+#define MX25_PAD_LD1__LD1 0x0cc 0x2c4 0x000 0x00 0x000
+#define MX25_PAD_LD1__CSI_D1 0x0cc 0x2c4 0x48c 0x02 0x000
+#define MX25_PAD_LD1__GPIO_2_16 0x0cc 0x2c4 0x000 0x05 0x000
-#define MX25_PAD_LD2__LD2 0x0d0 0x2c8 0x000 0x10 0x000
-#define MX25_PAD_LD2__GPIO_2_17 0x0d0 0x2c8 0x000 0x15 0x000
+#define MX25_PAD_LD2__LD2 0x0d0 0x2c8 0x000 0x00 0x000
+#define MX25_PAD_LD2__GPIO_2_17 0x0d0 0x2c8 0x000 0x05 0x000
-#define MX25_PAD_LD3__LD3 0x0d4 0x2cc 0x000 0x10 0x000
-#define MX25_PAD_LD3__GPIO_2_18 0x0d4 0x2cc 0x000 0x15 0x000
+#define MX25_PAD_LD3__LD3 0x0d4 0x2cc 0x000 0x00 0x000
+#define MX25_PAD_LD3__GPIO_2_18 0x0d4 0x2cc 0x000 0x05 0x000
-#define MX25_PAD_LD4__LD4 0x0d8 0x2d0 0x000 0x10 0x000
-#define MX25_PAD_LD4__GPIO_2_19 0x0d8 0x2d0 0x000 0x15 0x000
+#define MX25_PAD_LD4__LD4 0x0d8 0x2d0 0x000 0x00 0x000
+#define MX25_PAD_LD4__GPIO_2_19 0x0d8 0x2d0 0x000 0x05 0x000
-#define MX25_PAD_LD5__LD5 0x0dc 0x2d4 0x000 0x10 0x000
-#define MX25_PAD_LD5__GPIO_1_19 0x0dc 0x2d4 0x000 0x15 0x000
+#define MX25_PAD_LD5__LD5 0x0dc 0x2d4 0x000 0x00 0x000
+#define MX25_PAD_LD5__GPIO_1_19 0x0dc 0x2d4 0x000 0x05 0x000
-#define MX25_PAD_LD6__LD6 0x0e0 0x2d8 0x000 0x10 0x000
-#define MX25_PAD_LD6__GPIO_1_20 0x0e0 0x2d8 0x000 0x15 0x000
+#define MX25_PAD_LD6__LD6 0x0e0 0x2d8 0x000 0x00 0x000
+#define MX25_PAD_LD6__GPIO_1_20 0x0e0 0x2d8 0x000 0x05 0x000
-#define MX25_PAD_LD7__LD7 0x0e4 0x2dc 0x000 0x10 0x000
-#define MX25_PAD_LD7__GPIO_1_21 0x0e4 0x2dc 0x000 0x15 0x000
+#define MX25_PAD_LD7__LD7 0x0e4 0x2dc 0x000 0x00 0x000
+#define MX25_PAD_LD7__GPIO_1_21 0x0e4 0x2dc 0x000 0x05 0x000
-#define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x10 0x000
-#define MX25_PAD_LD8__UART4_RXD 0x0e8 0x2e0 0x570 0x12 0x000
-#define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x15 0x000
+#define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x00 0x000
+#define MX25_PAD_LD8__UART4_RXD 0x0e8 0x2e0 0x570 0x02 0x000
+#define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x05 0x000
#define MX25_PAD_LD8__SDHC2_CMD 0x0e8 0x2e0 0x4e0 0x06 0x000
-#define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x10 0x000
-#define MX25_PAD_LD9__UART4_TXD 0x0ec 0x2e4 0x000 0x12 0x000
-#define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x15 0x001
+#define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x00 0x000
+#define MX25_PAD_LD9__UART4_TXD 0x0ec 0x2e4 0x000 0x02 0x000
+#define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x05 0x001
#define MX25_PAD_LD9__SDHC2_CLK 0x0ec 0x2e4 0x4dc 0x06 0x000
#define MX25_PAD_LD10__LD10 0x0f0 0x2e8 0x000 0x00 0x000
#define MX25_PAD_LD10__UART4_RTS 0x0f0 0x2e8 0x56c 0x02 0x000
#define MX25_PAD_LD10__FEC_RX_ERR 0x0f0 0x2e8 0x518 0x05 0x001
-#define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x10 0x000
-#define MX25_PAD_LD11__UART4_CTS 0x0f4 0x2ec 0x000 0x12 0x000
-#define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x15 0x001
+#define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x00 0x000
+#define MX25_PAD_LD11__UART4_CTS 0x0f4 0x2ec 0x000 0x02 0x000
+#define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x05 0x001
#define MX25_PAD_LD11__SDHC2_DAT1 0x0f4 0x2ec 0x4e8 0x06 0x000
-#define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x10 0x000
+#define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x00 0x000
#define MX25_PAD_LD12__CSPI2_MOSI 0x0f8 0x2f0 0x4a0 0x02 0x000
-#define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x15 0x001
+#define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x05 0x001
-#define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x10 0x000
+#define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x00 0x000
#define MX25_PAD_LD13__CSPI2_MISO 0x0fc 0x2f4 0x49c 0x02 0x000
-#define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x15 0x000
+#define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x05 0x000
-#define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x10 0x000
+#define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x00 0x000
#define MX25_PAD_LD14__CSPI2_SCLK 0x100 0x2f8 0x494 0x02 0x000
-#define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x15 0x000
+#define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x05 0x000
-#define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x10 0x000
+#define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x00 0x000
#define MX25_PAD_LD15__CSPI2_RDY 0x104 0x2fc 0x498 0x02 0x000
-#define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x15 0x001
+#define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x05 0x001
-#define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x10 0x000
-#define MX25_PAD_HSYNC__GPIO_1_22 0x108 0x300 0x000 0x15 0x000
+#define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x00 0x000
+#define MX25_PAD_HSYNC__GPIO_1_22 0x108 0x300 0x000 0x05 0x000
-#define MX25_PAD_VSYNC__VSYNC 0x10c 0x304 0x000 0x10 0x000
-#define MX25_PAD_VSYNC__GPIO_1_23 0x10c 0x304 0x000 0x15 0x000
+#define MX25_PAD_VSYNC__VSYNC 0x10c 0x304 0x000 0x00 0x000
+#define MX25_PAD_VSYNC__GPIO_1_23 0x10c 0x304 0x000 0x05 0x000
-#define MX25_PAD_LSCLK__LSCLK 0x110 0x308 0x000 0x10 0x000
-#define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x15 0x000
+#define MX25_PAD_LSCLK__LSCLK 0x110 0x308 0x000 0x00 0x000
+#define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x05 0x000
-#define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x10 0x000
+#define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x00 0x000
#define MX25_PAD_OE_ACD__CSPI2_SS0 0x114 0x30c 0x4a4 0x02 0x000
-#define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x15 0x000
+#define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x05 0x000
-#define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x10 0x000
-#define MX25_PAD_CONTRAST__CC4 0x118 0x310 0x000 0x11 0x000
-#define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x14 0x000
-#define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x15 0x001
-#define MX25_PAD_CONTRAST__USBH2_PWR 0x118 0x310 0x000 0x16 0x000
+#define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x00 0x000
+#define MX25_PAD_CONTRAST__CC4 0x118 0x310 0x000 0x01 0x000
+#define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x04 0x000
+#define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x05 0x001
+#define MX25_PAD_CONTRAST__USBH2_PWR 0x118 0x310 0x000 0x06 0x000
-#define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x10 0x000
-#define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x15 0x000
-#define MX25_PAD_PWM__USBH2_OC 0x11c 0x314 0x580 0x16 0x001
+#define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x00 0x000
+#define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x05 0x000
+#define MX25_PAD_PWM__USBH2_OC 0x11c 0x314 0x580 0x06 0x001
-#define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x10 0x000
-#define MX25_PAD_CSI_D2__UART5_RXD 0x120 0x318 0x578 0x11 0x001
+#define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x00 0x000
+#define MX25_PAD_CSI_D2__UART5_RXD 0x120 0x318 0x578 0x01 0x001
#define MX25_PAD_CSI_D2__SIM1_CLK0 0x120 0x318 0x000 0x04 0x000
-#define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x15 0x000
-#define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x17 0x000
+#define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x05 0x000
+#define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x07 0x000
-#define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x10 0x000
-#define MX25_PAD_CSI_D3__UART5_TXD 0x124 0x31c 0x000 0x11 0x000
+#define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x00 0x000
+#define MX25_PAD_CSI_D3__UART5_TXD 0x124 0x31c 0x000 0x01 0x000
#define MX25_PAD_CSI_D3__SIM1_RST0 0x124 0x31c 0x000 0x04 0x000
-#define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x15 0x000
-#define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x17 0x001
+#define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x05 0x000
+#define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x07 0x001
#define MX25_PAD_CSI_D4__CSI_D4 0x128 0x320 0x000 0x00 0x000
#define MX25_PAD_CSI_D4__UART5_RTS 0x128 0x320 0x574 0x01 0x001
#define MX25_PAD_CSI_D4__GPIO_1_29 0x128 0x320 0x000 0x05 0x000
#define MX25_PAD_CSI_D4__CSPI3_SCLK 0x128 0x320 0x000 0x07 0x000
-#define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x10 0x000
-#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x11 0x000
+#define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x00 0x000
+#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x01 0x000
#define MX25_PAD_CSI_D5__SIM1_TX0 0x12c 0x324 0x000 0x04 0x000
-#define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x15 0x000
-#define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x17 0x000
+#define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x05 0x000
+#define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x07 0x000
-#define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x10 0x000
-#define MX25_PAD_CSI_D6__SDHC2_CMD 0x130 0x328 0x4e0 0x12 0x001
+#define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x00 0x000
+#define MX25_PAD_CSI_D6__SDHC2_CMD 0x130 0x328 0x4e0 0x02 0x001
#define MX25_PAD_CSI_D6__SIM1_PD0 0x130 0x328 0x000 0x04 0x000
-#define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x15 0x000
+#define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x05 0x000
-#define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x10 0x000
-#define MX25_PAD_CSI_D7__SDHC2_DAT_CLK 0x134 0x32C 0x4dc 0x12 0x001
-#define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x15 0x000
+#define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x00 0x000
+#define MX25_PAD_CSI_D7__SDHC2_DAT_CLK 0x134 0x32C 0x4dc 0x02 0x001
+#define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x05 0x000
-#define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x10 0x000
-#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x12 0x000
-#define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x15 0x000
-#define MX25_PAD_CSI_D8__CSPI3_SS2 0x138 0x330 0x4c4 0x17 0x000
+#define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x00 0x000
+#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x02 0x000
+#define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x05 0x000
+#define MX25_PAD_CSI_D8__CSPI3_SS2 0x138 0x330 0x4c4 0x07 0x000
-#define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x10 0x000
-#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x12 0x000
-#define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x15 0x000
-#define MX25_PAD_CSI_D9__CSPI3_SS3 0x13c 0x334 0x4c8 0x17 0x000
+#define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x00 0x000
+#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x02 0x000
+#define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x05 0x000
+#define MX25_PAD_CSI_D9__CSPI3_SS3 0x13c 0x334 0x4c8 0x07 0x000
-#define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x10 0x000
-#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x11 0x000
-#define MX25_PAD_CSI_MCLK__SDHC2_DAT0 0x140 0x338 0x4e4 0x12 0x001
-#define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x15 0x000
+#define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x00 0x000
+#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x01 0x000
+#define MX25_PAD_CSI_MCLK__SDHC2_DAT0 0x140 0x338 0x4e4 0x02 0x001
+#define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x05 0x000
-#define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x10 0x000
-#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x11 0x000
-#define MX25_PAD_CSI_VSYNC__SDHC2_DAT1 0x144 0x33c 0x4e8 0x12 0x001
-#define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x15 0x000
+#define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x00 0x000
+#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x01 0x000
+#define MX25_PAD_CSI_VSYNC__SDHC2_DAT1 0x144 0x33c 0x4e8 0x02 0x001
+#define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x05 0x000
-#define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x10 0x000
-#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x11 0x000
-#define MX25_PAD_CSI_HSYNC__SDHC2_DAT2 0x148 0x340 0x4ec 0x12 0x001
-#define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x15 0x000
+#define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x00 0x000
+#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x01 0x000
+#define MX25_PAD_CSI_HSYNC__SDHC2_DAT2 0x148 0x340 0x4ec 0x02 0x001
+#define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x05 0x000
-#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x10 0x000
-#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x11 0x000
-#define MX25_PAD_CSI_PIXCLK__SDHC2_DAT3 0x14c 0x344 0x4f0 0x12 0x001
-#define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x15 0x000
+#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x00 0x000
+#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x01 0x000
+#define MX25_PAD_CSI_PIXCLK__SDHC2_DAT3 0x14c 0x344 0x4f0 0x02 0x001
+#define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x05 0x000
-#define MX25_PAD_I2C1_CLK__I2C1_CLK 0x150 0x348 0x000 0x10 0x000
-#define MX25_PAD_I2C1_CLK__GPIO_1_12 0x150 0x348 0x000 0x15 0x000
+#define MX25_PAD_I2C1_CLK__I2C1_CLK 0x150 0x348 0x000 0x00 0x000
+#define MX25_PAD_I2C1_CLK__GPIO_1_12 0x150 0x348 0x000 0x05 0x000
-#define MX25_PAD_I2C1_DAT__I2C1_DAT 0x154 0x34c 0x000 0x10 0x000
-#define MX25_PAD_I2C1_DAT__GPIO_1_13 0x154 0x34c 0x000 0x15 0x000
+#define MX25_PAD_I2C1_DAT__I2C1_DAT 0x154 0x34c 0x000 0x00 0x000
+#define MX25_PAD_I2C1_DAT__GPIO_1_13 0x154 0x34c 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI 0x158 0x350 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_MOSI__UART3_RXD 0x158 0x350 0x568 0x12 0x000
-#define MX25_PAD_CSPI1_MOSI__GPIO_1_14 0x158 0x350 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI 0x158 0x350 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_MOSI__UART3_RXD 0x158 0x350 0x568 0x02 0x000
+#define MX25_PAD_CSPI1_MOSI__GPIO_1_14 0x158 0x350 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_MISO__CSPI1_MISO 0x15c 0x354 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_MISO__UART3_TXD 0x15c 0x354 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_MISO__GPIO_1_15 0x15c 0x354 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_MISO__CSPI1_MISO 0x15c 0x354 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_MISO__UART3_TXD 0x15c 0x354 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_MISO__GPIO_1_15 0x15c 0x354 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_SS0__CSPI1_SS0 0x160 0x358 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_SS0__PWM2_PWMO 0x160 0x358 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_SS0__GPIO_1_16 0x160 0x358 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_SS0__CSPI1_SS0 0x160 0x358 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_SS0__PWM2_PWMO 0x160 0x358 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_SS0__GPIO_1_16 0x160 0x358 0x000 0x05 0x000
#define MX25_PAD_CSPI1_SS1__CSPI1_SS1 0x164 0x35c 0x000 0x00 0x000
#define MX25_PAD_CSPI1_SS1__I2C3_DAT 0x164 0x35C 0x528 0x01 0x001
#define MX25_PAD_CSPI1_SS1__UART3_RTS 0x164 0x35c 0x000 0x02 0x000
#define MX25_PAD_CSPI1_SS1__GPIO_1_17 0x164 0x35c 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK 0x168 0x360 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_SCLK__UART3_CTS 0x168 0x360 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_SCLK__GPIO_1_18 0x168 0x360 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK 0x168 0x360 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_SCLK__UART3_CTS 0x168 0x360 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_SCLK__GPIO_1_18 0x168 0x360 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_RDY__CSPI1_RDY 0x16c 0x364 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_RDY__GPIO_2_22 0x16c 0x364 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_RDY__CSPI1_RDY 0x16c 0x364 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_RDY__GPIO_2_22 0x16c 0x364 0x000 0x05 0x000
#define MX25_PAD_UART1_RXD__UART1_RXD 0x170 0x368 0x000 0x00 0x000
#define MX25_PAD_UART1_RXD__UART2_DTR 0x170 0x368 0x000 0x03 0x000
#define MX25_PAD_UART1_CTS__UART2_RI 0x17c 0x374 0x000 0x03 0x001
#define MX25_PAD_UART1_CTS__GPIO_4_25 0x17c 0x374 0x000 0x05 0x000
-#define MX25_PAD_UART2_RXD__UART2_RXD 0x180 0x378 0x000 0x10 0x000
-#define MX25_PAD_UART2_RXD__GPIO_4_26 0x180 0x378 0x000 0x15 0x000
+#define MX25_PAD_UART2_RXD__UART2_RXD 0x180 0x378 0x000 0x00 0x000
+#define MX25_PAD_UART2_RXD__GPIO_4_26 0x180 0x378 0x000 0x05 0x000
-#define MX25_PAD_UART2_TXD__UART2_TXD 0x184 0x37c 0x000 0x10 0x000
-#define MX25_PAD_UART2_TXD__GPIO_4_27 0x184 0x37c 0x000 0x15 0x000
+#define MX25_PAD_UART2_TXD__UART2_TXD 0x184 0x37c 0x000 0x00 0x000
+#define MX25_PAD_UART2_TXD__GPIO_4_27 0x184 0x37c 0x000 0x05 0x000
#define MX25_PAD_UART2_RTS__UART2_RTS 0x188 0x380 0x000 0x00 0x000
#define MX25_PAD_UART2_RTS__FEC_COL 0x188 0x380 0x504 0x02 0x002
#define MX25_PAD_UART2_RTS__CC1 0x188 0x380 0x000 0x03 0x000
#define MX25_PAD_UART2_RTS__GPIO_4_28 0x188 0x380 0x000 0x05 0x000
-#define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x10 0x000
-#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x12 0x002
-#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x15 0x000
+#define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x00 0x000
+#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x02 0x002
+#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x05 0x000
+/*
+ * Removing the SION bit from MX25_PAD_SD1_CMD__SD1_CMD breaks detecting an SD
+ * card. According to the i.MX25 reference manual (e.g. Figure 23-2 in IMX25RM
+ * Rev. 2 from 01/2011) this pin is bidirectional. So it seems to be a silicon
+ * bug that configuring the SD1_CMD function doesn't enable the input path for
+ * this pin.
+ * This might have side effects for other hardware units that are connected to
+ * that pin and use the respective function as input.
+ */
#define MX25_PAD_SD1_CMD__SD1_CMD 0x190 0x388 0x000 0x10 0x000
-#define MX25_PAD_SD1_CMD__CSPI2_MOSI 0x190 0x388 0x4a0 0x11 0x001
-#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x12 0x002
-#define MX25_PAD_SD1_CMD__GPIO_2_23 0x190 0x388 0x000 0x15 0x000
+#define MX25_PAD_SD1_CMD__CSPI2_MOSI 0x190 0x388 0x4a0 0x01 0x001
+#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x02 0x002
+#define MX25_PAD_SD1_CMD__GPIO_2_23 0x190 0x388 0x000 0x05 0x000
-#define MX25_PAD_SD1_CLK__SD1_CLK 0x194 0x38c 0x000 0x10 0x000
-#define MX25_PAD_SD1_CLK__CSPI2_MISO 0x194 0x38c 0x49c 0x11 0x001
-#define MX25_PAD_SD1_CLK__FEC_RDATA3 0x194 0x38c 0x510 0x12 0x002
-#define MX25_PAD_SD1_CLK__GPIO_2_24 0x194 0x38c 0x000 0x15 0x000
+#define MX25_PAD_SD1_CLK__SD1_CLK 0x194 0x38c 0x000 0x00 0x000
+#define MX25_PAD_SD1_CLK__CSPI2_MISO 0x194 0x38c 0x49c 0x01 0x001
+#define MX25_PAD_SD1_CLK__FEC_RDATA3 0x194 0x38c 0x510 0x02 0x002
+#define MX25_PAD_SD1_CLK__GPIO_2_24 0x194 0x38c 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA0__SD1_DATA0 0x198 0x390 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA0__CSPI2_SCLK 0x198 0x390 0x494 0x11 0x001
-#define MX25_PAD_SD1_DATA0__GPIO_2_25 0x198 0x390 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA0__SD1_DATA0 0x198 0x390 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA0__CSPI2_SCLK 0x198 0x390 0x494 0x01 0x001
+#define MX25_PAD_SD1_DATA0__GPIO_2_25 0x198 0x390 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA1__SD1_DATA1 0x19c 0x394 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA1__AUD7_RXD 0x19c 0x394 0x478 0x13 0x000
-#define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA1__SD1_DATA1 0x19c 0x394 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA1__AUD7_RXD 0x19c 0x394 0x478 0x03 0x000
+#define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x12 0x002
-#define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x02 0x002
+#define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x12 0x002
-#define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x02 0x002
+#define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x05 0x000
#define MX25_PAD_KPP_ROW0__KPP_ROW0 0x1a8 0x3a0 0x000 0x00 0x000
#define MX25_PAD_KPP_ROW0__UART3_RXD 0x1a8 0x3a0 0x568 0x01 0x001
#define MX25_PAD_KPP_ROW3__UART1_RI 0x1b4 0x3ac 0x000 0x04 0x000
#define MX25_PAD_KPP_ROW3__GPIO_3_0 0x1b4 0x3ac 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL0__UART4_RXD 0x1b8 0x3b0 0x570 0x11 0x001
-#define MX25_PAD_KPP_COL0__AUD5_TXD 0x1b8 0x3b0 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL0__GPIO_3_1 0x1b8 0x3b0 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL0__UART4_RXD 0x1b8 0x3b0 0x570 0x01 0x001
+#define MX25_PAD_KPP_COL0__AUD5_TXD 0x1b8 0x3b0 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL0__GPIO_3_1 0x1b8 0x3b0 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL1__KPP_COL1 0x1bc 0x3b4 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL1__UART4_TXD 0x1bc 0x3b4 0x000 0x11 0x000
-#define MX25_PAD_KPP_COL1__AUD5_RXD 0x1bc 0x3b4 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL1__GPIO_3_2 0x1bc 0x3b4 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL1__KPP_COL1 0x1bc 0x3b4 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL1__UART4_TXD 0x1bc 0x3b4 0x000 0x01 0x000
+#define MX25_PAD_KPP_COL1__AUD5_RXD 0x1bc 0x3b4 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL1__GPIO_3_2 0x1bc 0x3b4 0x000 0x05 0x000
#define MX25_PAD_KPP_COL2__KPP_COL2 0x1c0 0x3b8 0x000 0x00 0x000
#define MX25_PAD_KPP_COL2__UART4_RTS 0x1c0 0x3b8 0x56c 0x01 0x001
#define MX25_PAD_KPP_COL2__AUD5_TXC 0x1c0 0x3b8 0x000 0x02 0x000
#define MX25_PAD_KPP_COL2__GPIO_3_3 0x1c0 0x3b8 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL3__KPP_COL3 0x1c4 0x3bc 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL3__UART4_CTS 0x1c4 0x3bc 0x000 0x11 0x000
-#define MX25_PAD_KPP_COL3__AUD5_TXFS 0x1c4 0x3bc 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL3__GPIO_3_4 0x1c4 0x3bc 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL3__KPP_COL3 0x1c4 0x3bc 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL3__UART4_CTS 0x1c4 0x3bc 0x000 0x01 0x000
+#define MX25_PAD_KPP_COL3__AUD5_TXFS 0x1c4 0x3bc 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL3__GPIO_3_4 0x1c4 0x3bc 0x000 0x05 0x000
-#define MX25_PAD_FEC_MDC__FEC_MDC 0x1c8 0x3c0 0x000 0x10 0x000
-#define MX25_PAD_FEC_MDC__AUD4_TXD 0x1c8 0x3c0 0x464 0x12 0x001
-#define MX25_PAD_FEC_MDC__GPIO_3_5 0x1c8 0x3c0 0x000 0x15 0x000
+#define MX25_PAD_FEC_MDC__FEC_MDC 0x1c8 0x3c0 0x000 0x00 0x000
+#define MX25_PAD_FEC_MDC__AUD4_TXD 0x1c8 0x3c0 0x464 0x02 0x001
+#define MX25_PAD_FEC_MDC__GPIO_3_5 0x1c8 0x3c0 0x000 0x05 0x000
-#define MX25_PAD_FEC_MDIO__FEC_MDIO 0x1cc 0x3c4 0x000 0x10 0x000
-#define MX25_PAD_FEC_MDIO__AUD4_RXD 0x1cc 0x3c4 0x460 0x12 0x001
-#define MX25_PAD_FEC_MDIO__GPIO_3_6 0x1cc 0x3c4 0x000 0x15 0x000
+#define MX25_PAD_FEC_MDIO__FEC_MDIO 0x1cc 0x3c4 0x000 0x00 0x000
+#define MX25_PAD_FEC_MDIO__AUD4_RXD 0x1cc 0x3c4 0x460 0x02 0x001
+#define MX25_PAD_FEC_MDIO__GPIO_3_6 0x1cc 0x3c4 0x000 0x05 0x000
-#define MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x1d0 0x3c8 0x000 0x10 0x000
-#define MX25_PAD_FEC_TDATA0__GPIO_3_7 0x1d0 0x3c8 0x000 0x15 0x000
+#define MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x1d0 0x3c8 0x000 0x00 0x000
+#define MX25_PAD_FEC_TDATA0__GPIO_3_7 0x1d0 0x3c8 0x000 0x05 0x000
-#define MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x1d4 0x3cc 0x000 0x10 0x000
-#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 0x1d4 0x3cc 0x474 0x12 0x001
-#define MX25_PAD_FEC_TDATA1__GPIO_3_8 0x1d4 0x3cc 0x000 0x15 0x000
+#define MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x1d4 0x3cc 0x000 0x00 0x000
+#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 0x1d4 0x3cc 0x474 0x02 0x001
+#define MX25_PAD_FEC_TDATA1__GPIO_3_8 0x1d4 0x3cc 0x000 0x05 0x000
-#define MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x1d8 0x3d0 0x000 0x10 0x000
-#define MX25_PAD_FEC_TX_EN__GPIO_3_9 0x1d8 0x3d0 0x000 0x15 0x000
+#define MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x1d8 0x3d0 0x000 0x00 0x000
+#define MX25_PAD_FEC_TX_EN__GPIO_3_9 0x1d8 0x3d0 0x000 0x05 0x000
-#define MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x1dc 0x3d4 0x000 0x10 0x000
-#define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x15 0x000
+#define MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x1dc 0x3d4 0x000 0x00 0x000
+#define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x05 0x000
-#define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x10 0x000
+#define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x00 0x000
/*
* According to the i.MX25 Reference manual (IMX25RM, Rev. 2,
* 01/2011) this is CAN1_TX but that's wrong.
*/
-#define MX25_PAD_FEC_RDATA1__CAN2_TX 0x1e0 0x3d8 0x000 0x14 0x000
-#define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x15 0x000
+#define MX25_PAD_FEC_RDATA1__CAN2_TX 0x1e0 0x3d8 0x000 0x04 0x000
+#define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x05 0x000
-#define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x10 0x000
+#define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x00 0x000
/*
* According to the i.MX25 Reference manual (IMX25RM, Rev. 2,
* 01/2011) this is CAN1_RX but that's wrong.
*/
-#define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x14 0x000
-#define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x15 0x000
+#define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x04 0x000
+#define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x05 0x000
-#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1e8 0x3e0 0x000 0x10 0x000
-#define MX25_PAD_FEC_TX_CLK__GPIO_3_13 0x1e8 0x3e0 0x000 0x15 0x000
+#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1e8 0x3e0 0x000 0x00 0x000
+#define MX25_PAD_FEC_TX_CLK__GPIO_3_13 0x1e8 0x3e0 0x000 0x05 0x000
-#define MX25_PAD_RTCK__RTCK 0x1ec 0x3e4 0x000 0x10 0x000
-#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x11 0x000
-#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x15 0x000
+#define MX25_PAD_RTCK__RTCK 0x1ec 0x3e4 0x000 0x00 0x000
+#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x01 0x000
+#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x05 0x000
-#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x10 0x000
-#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x15 0x000
+#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x00 0x000
+#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x05 0x000
-#define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x10 0x000
-#define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x16 0x000
-#define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x12 0x000
+#define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x00 0x000
+#define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x06 0x000
+#define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x02 0x000
-#define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x10 0x000
-#define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x12 0x001
-#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x16 0x001
+#define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x00 0x000
+#define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x02 0x001
+#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x06 0x001
-#define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x10 0x000
-#define MX25_PAD_GPIO_C__PWM4_PWMO 0x1fc 0x3f8 0x000 0x11 0x000
-#define MX25_PAD_GPIO_C__I2C2_SCL 0x1fc 0x3f8 0x51c 0x12 0x001
-#define MX25_PAD_GPIO_C__KPP_COL4 0x1fc 0x3f8 0x52c 0x13 0x001
-#define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x16 0x000
+#define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x00 0x000
+#define MX25_PAD_GPIO_C__PWM4_PWMO 0x1fc 0x3f8 0x000 0x01 0x000
+#define MX25_PAD_GPIO_C__I2C2_SCL 0x1fc 0x3f8 0x51c 0x02 0x001
+#define MX25_PAD_GPIO_C__KPP_COL4 0x1fc 0x3f8 0x52c 0x03 0x001
+#define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x06 0x000
-#define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x10 0x000
-#define MX25_PAD_GPIO_D__I2C2_SDA 0x200 0x3fc 0x520 0x12 0x001
-#define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x16 0x001
+#define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x00 0x000
+#define MX25_PAD_GPIO_D__I2C2_SDA 0x200 0x3fc 0x520 0x02 0x001
+#define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x06 0x001
-#define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x10 0x000
-#define MX25_PAD_GPIO_E__I2C3_CLK 0x204 0x400 0x524 0x11 0x002
-#define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x12 0x000
-#define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x14 0x000
-#define MX25_PAD_GPIO_E__UART4_RXD 0x204 0x400 0x570 0x16 0x002
+#define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x00 0x000
+#define MX25_PAD_GPIO_E__I2C3_CLK 0x204 0x400 0x524 0x01 0x002
+#define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x02 0x000
+#define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x04 0x000
+#define MX25_PAD_GPIO_E__UART4_RXD 0x204 0x400 0x570 0x06 0x002
-#define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x10 0x000
-#define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x12 0x000
-#define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x14 0x000
-#define MX25_PAD_GPIO_F__UART4_TXD 0x208 0x404 0x000 0x16 0x000
+#define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x00 0x000
+#define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x02 0x000
+#define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x04 0x000
+#define MX25_PAD_GPIO_F__UART4_TXD 0x208 0x404 0x000 0x06 0x000
-#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x10 0x000
-#define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x15 0x000
+#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x00 0x000
+#define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x05 0x000
-#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK 0x210 0x000 0x000 0x10 0x000
-#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16 0x210 0x000 0x000 0x15 0x000
+#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK 0x210 0x000 0x000 0x00 0x000
+#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16 0x210 0x000 0x000 0x05 0x000
#define MX25_PAD_VSTBY_REQ__VSTBY_REQ 0x214 0x408 0x000 0x00 0x000
#define MX25_PAD_VSTBY_REQ__AUD7_TXFS 0x214 0x408 0x000 0x04 0x000
#define MX25_PAD_VSTBY_REQ__GPIO_3_17 0x214 0x408 0x000 0x05 0x000
#define MX25_PAD_VSTBY_REQ__UART4_RTS 0x214 0x408 0x56c 0x06 0x002
-#define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x10 0x000
-#define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x15 0x000
+#define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x00 0x000
+#define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x05 0x000
-#define MX25_PAD_POWER_FAIL__POWER_FAIL 0x21c 0x410 0x000 0x10 0x000
-#define MX25_PAD_POWER_FAIL__AUD7_RXD 0x21c 0x410 0x478 0x14 0x001
-#define MX25_PAD_POWER_FAIL__GPIO_3_19 0x21c 0x410 0x000 0x15 0x000
-#define MX25_PAD_POWER_FAIL__UART4_CTS 0x21c 0x410 0x000 0x16 0x000
+#define MX25_PAD_POWER_FAIL__POWER_FAIL 0x21c 0x410 0x000 0x00 0x000
+#define MX25_PAD_POWER_FAIL__AUD7_RXD 0x21c 0x410 0x478 0x04 0x001
+#define MX25_PAD_POWER_FAIL__GPIO_3_19 0x21c 0x410 0x000 0x05 0x000
+#define MX25_PAD_POWER_FAIL__UART4_CTS 0x21c 0x410 0x000 0x06 0x000
-#define MX25_PAD_CLKO__CLKO 0x220 0x414 0x000 0x10 0x000
-#define MX25_PAD_CLKO__GPIO_2_21 0x220 0x414 0x000 0x15 0x000
+#define MX25_PAD_CLKO__CLKO 0x220 0x414 0x000 0x00 0x000
+#define MX25_PAD_CLKO__GPIO_2_21 0x220 0x414 0x000 0x05 0x000
#define MX25_PAD_BOOT_MODE0__BOOT_MODE0 0x224 0x000 0x000 0x00 0x000
#define MX25_PAD_BOOT_MODE0__GPIO_4_30 0x224 0x000 0x000 0x05 0x000
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
};
&uart1 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
&uart1 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart1 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
&uart1 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_pins_a>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
};
- onewire@0 {
+ onewire {
compatible = "w1-gpio";
pinctrl-names = "default";
pinctrl-0 = <&w1_gpio_pins>;
reg_3p3v: regulator@0 {
compatible = "regulator-fixed";
+ reg = <0>;
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
reg_lcd_3v3: regulator@1 {
compatible = "regulator-fixed";
+ reg = <1>;
pinctrl-names = "default";
pinctrl-0 = <®_lcd_3v3_pins_mbmx28lc>;
regulator-name = "lcd-3v3";
reg_usb0_vbus: regulator@2 {
compatible = "regulator-fixed";
+ reg = <2>;
pinctrl-names = "default";
pinctrl-0 = <®_usb0_vbus_pins_mbmx28lc>;
regulator-name = "usb0_vbus";
reg_usb1_vbus: regulator@3 {
compatible = "regulator-fixed";
+ reg = <3>;
pinctrl-names = "default";
pinctrl-0 = <®_usb1_vbus_pins_mbmx28lc>;
regulator-name = "usb1_vbus";
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_pins_a>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
default-brightness-level = <50>;
};
- matrix_keypad: matrix-keypad@0 {
+ matrix_keypad: matrix-keypad {
compatible = "gpio-matrix-keypad";
col-gpios = <
&gpio5 0 GPIO_ACTIVE_HIGH
gpio0: gpio@0 {
compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ reg = <0>;
interrupts = <127>;
gpio-controller;
#gpio-cells = <2>;
gpio1: gpio@1 {
compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ reg = <1>;
interrupts = <126>;
gpio-controller;
#gpio-cells = <2>;
gpio2: gpio@2 {
compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ reg = <2>;
interrupts = <125>;
gpio-controller;
#gpio-cells = <2>;
gpio3: gpio@3 {
compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ reg = <3>;
interrupts = <124>;
gpio-controller;
#gpio-cells = <2>;
gpio4: gpio@4 {
compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ reg = <4>;
interrupts = <123>;
gpio-controller;
#gpio-cells = <2>;
};
&uart5 {
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3 &pinctrl_uart3_rtscts>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
reg = <0x12000 0x1000>;
syscon = <&syscon 0x10 6>;
};
+
+ fpga_irqc: fpga-irqc@15000 {
+ compatible = "technologic,ts4800-irqc";
+ reg = <0x15000 0x1000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_interrupt_fpga>;
+ interrupt-parent = <&gpio2>;
+ interrupts= <9 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ can@1a000 {
+ compatible = "technologic,sja1000";
+ reg = <0x1a000 0x100>;
+ interrupt-parent = <&fpga_irqc>;
+ interrupts = <1>;
+ reg-io-width = <2>;
+ nxp,tx-output-config = <0x06>;
+ nxp,external-clock-frequency = <24000000>;
+ };
};
};
>;
};
+ pinctrl_interrupt_fpga: fpgaicgrp {
+ fsl,pins = <
+ MX51_PAD_EIM_D27__GPIO2_9 0xe5
+ >;
+ };
+
pinctrl_lcd: lcdgrp {
fsl,pins = <
MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "disabled";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
phy-reset-gpios = <&gpio3 31 0>;
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
reg = <0>;
lcd_display_in: endpoint {
- remote-endpoint = <&ipu1_di0_disp1>;
+ remote-endpoint = <&ipu1_di1_disp1>;
};
};
};
};
-&ipu1_di0_disp1 {
+&ipu1_di1_disp1 {
remote-endpoint = <&lcd_display_in>;
};
phy-mode = "rgmii";
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
fsl,dte-mode;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
};
};
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+
reg_wl18xx_vmmc: regulator-wl18xx {
compatible = "regulator-fixed";
regulator-name = "vwl1807";
*
* Author: Valentin Raevsky <valentin@compulab.co.il>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "imx6q.dtsi"
/ {
linux,default-trigger = "heartbeat";
};
};
+
+ reg_pcie_power_on_gpio: regulator-pcie-power-on-gpio {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-pcie-power-on-gpio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: usb_h1_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg_vbus: usb_otg_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&cpu0 {
+ /*
+ * Although the imx6q fuse indicates that 1.2GHz operation is possible,
+ * the module behaves unstable at this frequency. Hence, remove the
+ * 1.2GHz operation point here.
+ */
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 975000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 1175000
+ >;
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
};
&fec {
status = "okay";
};
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+ clock-frequency = <100000>;
+
+ eeprom@50 {
+ compatible = "at24,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
&iomuxc {
- imx6q-cm-fx6 {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
- >;
- };
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x100b1
+ >;
+ };
- pinctrl_gpmi_nand: gpminandgrp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
- MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
- MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
- MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
- MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
- MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
- MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
- MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
- MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
- MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
- MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
- MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
- MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
- MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
- MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
- MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
- MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
- >;
- };
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ >;
+ };
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
- >;
- };
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
};
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x130b0
+ >;
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 26 GPIO_ACTIVE_LOW>;
+ vdd-supply = <®_pcie_power_on_gpio>;
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
};
&uart4 {
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ dr_mode = "otg";
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (C) 2015 Lucas Stach <kernel@pengutronix.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-microsom.dtsi"
+#include "imx6qdl-microsom-ar8035.dtsi"
+
+/ {
+ model = "Auvidea H100";
+ compatible = "auvidea,h100", "fsl,imx6q";
+
+ aliases {
+ rtc0 = &rtc;
+ rtc1 = &snvs_rtc;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ hdmi_osc: hdmi-osc {
+ compatible = "fixed-clock";
+ clock-output-names = "hdmi-osc";
+ clock-frequency = <27000000>;
+ #clock-cells = <0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_leds>;
+
+ led0: power {
+ label = "power";
+ gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led1: stream {
+ label = "stream";
+ gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led2: rec {
+ label = "rec";
+ gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_hdmi: regulator-hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_reg_hdmi>;
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ regulator-name = "V_HDMI";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_nvcc_sd2: regulator-nvcc-sd2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_reg_nvcc_sd2>;
+ compatible = "regulator-gpio";
+ regulator-name = "NVCC_SD2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+
+ reg_usbh1_vbus: regulator-usb-h1-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_usbh1_vbus>;
+ regulator-name = "USB_H1_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usbotg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_usbotg_vbus>;
+ regulator-name = "USB_OTG_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ sound-sgtl5000 {
+ compatible = "fsl,imx-audio-sgtl5000";
+ model = "H100 on-board codec";
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-ext-port = <5>;
+ mux-int-port = <1>;
+ ssi-controller = <&ssi1>;
+ };
+};
+
+&audmux {
+ status = "okay";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_i2c1>;
+ status = "okay";
+
+ eeprom: 24c02@51 {
+ compatible = "microchip,24c02", "at24";
+ reg = <0x51>;
+ };
+
+ rtc: pcf8523@68 {
+ compatible = "nxp,pcf8523";
+ reg = <0x68>;
+ };
+
+ sgtl5000: sgtl5000@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_sgtl5000>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+
+ tc358743: tc358743@0f {
+ compatible = "toshiba,tc358743";
+ reg = <0x0f>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_tc358743>;
+ clocks = <&hdmi_osc>;
+ clock-names = "refclk";
+ reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+ /* IRQ has a wrong pull resistor which renders it useless */
+
+ port@0 {
+ tc358743_out: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ data-lanes = <1 2 3 4>;
+ clock-lanes = <0>;
+ clock-noncontinuous;
+ link-frequencies = /bits/ 64 <297000000>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_i2c2>;
+ status = "okay";
+};
+
+&iomuxc {
+ h100 {
+ pinctrl_h100_hdmi: h100-hdmi {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_h100_i2c1: h100-i2c1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_h100_i2c2: h100-i2c2 {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_h100_leds: pinctrl-h100-leds {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b0
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_h100_reg_hdmi: h100-reg-hdmi {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_h100_reg_nvcc_sd2: h100-reg-nvcc-sd2 {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_h100_sgtl5000: h100-sgtl5000 {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+ MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
+ MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0
+ MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_h100_tc358743: h100-tc358743 {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+ >;
+ };
+
+ pinctrl_h100_uart2: h100-uart2 {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_h100_usbh1_vbus: hummingboard-usbh1-vbus {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_h100_usbotg_id: hummingboard-usbotg-id {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+ >;
+ };
+
+ pinctrl_h100_usbotg_vbus: hummingboard-usbotg-vbus {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_h100_usdhc2: h100-usdhc2 {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+ >;
+ };
+
+ pinctrl_h100_usdhc2_100mhz: h100-usdhc2-100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_h100_usdhc2_200mhz: h100-usdhc2-200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9
+ >;
+ };
+ };
+};
+
+&mipi_csi {
+ status = "okay";
+
+ port@0 {
+ mipi_csi2_in: endpoint {
+ remote-endpoint = <&tc358743_out>;
+ data-lanes = <1 2 3 4>;
+ clock-lanes = <0>;
+ clock-noncontinuous;
+ link-frequencies = /bits/ 64 <297000000>;
+ };
+ };
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ disable-over-current;
+ vbus-supply = <®_usbh1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ disable-over-current;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_h100_usbotg_id>;
+ vbus-supply = <®_usbotg_vbus>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_h100_usdhc2>;
+ pinctrl-1 = <&pinctrl_h100_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_h100_usdhc2_200mhz>;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_nvcc_sd2>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
- reset-gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2013 CompuLab Ltd.
+ * Copyright 2016 Christopher Spinrath
+ *
+ * Based on the devicetree distributed with the vendor kernel for the
+ * Utilite Pro:
+ * Copyright 2013 CompuLab Ltd.
+ * Author: Valentin Raevsky <valentin@compulab.co.il>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "imx6q-cm-fx6.dts"
+
+/ {
+ model = "CompuLab Utilite Pro";
+ compatible = "compulab,utilite-pro", "compulab,cm-fx6", "fsl,imx6q";
+
+ aliases {
+ ethernet1 = ð1;
+ rtc0 = &em3027;
+ rtc1 = &snvs_rtc;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+ };
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ eeprom@50 {
+ compatible = "at24,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ em3027: rtc@56 {
+ compatible = "emmicro,em3027";
+ reg = <0x56>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_GPIO_8__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
+ >;
+ };
+};
+
+&pcie {
+ pcie@0,0 {
+ reg = <0x000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ /* non-removable i211 ethernet card */
+ eth1: intel,i211@pcie0,0 {
+ reg = <0x010000 0 0 0 0>;
+ };
+ };
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ no-1-8-v;
+ broken-cd;
+ keep-power-in-suspend;
+ status = "okay";
+};
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
fsl,dte-mode;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "disabled";
};
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2_dte>;
fsl,dte-mode;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "disabled";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3 &pinctrl_gsm>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_brcm_bt &pinctrl_microsom_uart4>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
txd3-skew-ps = <0>;
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
txd3-skew-ps = <0>;
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
txd3-skew-ps = <0>;
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
phy-mode = "rgmii";
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
txd3-skew-ps = <0>;
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
>;
};
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
+ >;
+ };
};
gpio_leds {
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
- reset-gpio = <&gpio7 12 0>;
+ reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
status = "okay";
};
no-1-8-v;
status = "okay";
};
+
+&wdog1 {
+ status = "disabled";
+};
+
+&wdog2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3 &pinctrl_uart3_rtscts>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
phy-reset-gpios = <&gpio3 29 0>;
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
cache-level = <2>;
arm,tag-latency = <4 2 3>;
arm,data-latency = <4 2 3>;
+ arm,shared-override;
};
pcie: pcie@0x01000000 {
ocotp: ocotp@021bc000 {
compatible = "fsl,imx6q-ocotp", "syscon";
reg = <0x021bc000 0x4000>;
+ clocks = <&clks IMX6QDL_CLK_IIM>;
};
tzasc@021d0000 { /* TZASC1 */
#size-cells = <0>;
reg = <3>;
- ipu1_di0_disp1: disp1-endpoint {
+ ipu1_di1_disp1: disp1-endpoint {
};
ipu1_di1_hdmi: hdmi-endpoint {
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
<0 54 IRQ_TYPE_LEVEL_HIGH>,
<0 127 IRQ_TYPE_LEVEL_HIGH>;
- regulator-1p1@110 {
+ regulator-1p1 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd1p1";
regulator-min-microvolt = <800000>;
anatop-max-voltage = <1375000>;
};
- regulator-3p0@120 {
+ regulator-3p0 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd3p0";
regulator-min-microvolt = <2800000>;
anatop-max-voltage = <3400000>;
};
- regulator-2p5@130 {
+ regulator-2p5 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd2p5";
regulator-min-microvolt = <2100000>;
anatop-max-voltage = <2850000>;
};
- reg_arm: regulator-vddcore@140 {
+ reg_arm: regulator-vddcore {
compatible = "fsl,anatop-regulator";
regulator-name = "vddarm";
regulator-min-microvolt = <725000>;
anatop-max-voltage = <1450000>;
};
- reg_pu: regulator-vddpu@140 {
+ reg_pu: regulator-vddpu {
compatible = "fsl,anatop-regulator";
regulator-name = "vddpu";
regulator-min-microvolt = <725000>;
anatop-max-voltage = <1450000>;
};
- reg_soc: regulator-vddsoc@140 {
+ reg_soc: regulator-vddsoc {
compatible = "fsl,anatop-regulator";
regulator-name = "vddsoc";
regulator-min-microvolt = <725000>;
ocotp: ocotp@021bc000 {
compatible = "fsl,imx6sl-ocotp", "syscon";
reg = <0x021bc000 0x4000>;
+ clocks = <&clks IMX6SL_CLK_OCOTP>;
};
audmux: audmux@021d8000 {
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart5 { /* for bluetooth */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
status = "okay";
};
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
&iomuxc {
imx6x-sdb {
pinctrl_audmux: audmuxgrp {
MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */
>;
};
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO13__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
};
};
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
- regulator-1p1@110 {
+ regulator-1p1 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd1p1";
regulator-min-microvolt = <800000>;
anatop-max-voltage = <1375000>;
};
- regulator-3p0@120 {
+ regulator-3p0 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd3p0";
regulator-min-microvolt = <2800000>;
anatop-max-voltage = <3400000>;
};
- regulator-2p5@130 {
+ regulator-2p5 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd2p5";
regulator-min-microvolt = <2100000>;
anatop-max-voltage = <2875000>;
};
- reg_arm: regulator-vddcore@140 {
+ reg_arm: regulator-vddcore {
compatible = "fsl,anatop-regulator";
regulator-name = "vddarm";
regulator-min-microvolt = <725000>;
anatop-max-voltage = <1450000>;
};
- reg_pcie: regulator-vddpcie@140 {
+ reg_pcie: regulator-vddpcie {
compatible = "fsl,anatop-regulator";
regulator-name = "vddpcie";
regulator-min-microvolt = <725000>;
anatop-max-voltage = <1450000>;
};
- reg_soc: regulator-vddsoc@140 {
+ reg_soc: regulator-vddsoc {
compatible = "fsl,anatop-regulator";
regulator-name = "vddsoc";
regulator-min-microvolt = <725000>;
reg = <0x80000000 0x20000000>;
};
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
regulators {
compatible = "simple-bus";
#address-cells = <1>;
};
};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif_dat
+ &pinctrl_lcdif_ctrl>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+
+ timing0: timing0 {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <8>;
+ hback-porch = <4>;
+ hsync-len = <41>;
+ vback-porch = <2>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
&qspi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_qspi>;
<&clks IMX6UL_CLK_SAI2>;
assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
assigned-clock-rates = <0>, <12288000>;
+ fsl,sai-mclk-direction-output;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
status = "okay";
};
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
&iomuxc {
pinctrl-names = "default";
MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
>;
};
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
};
phy-mode = "rmii";
phy-handle = <ðphy1>;
status = "okay";
- phy-reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <11>;
+ phy-reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <1>;
mdio {
#address-cells = <1>;
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-0 = <&pinctrl_uart1>;
- /delete-property/ fsl,uart-has-rtscts;
+ /delete-property/ uart-has-rtscts;
};
&uart2 {
pinctrl-0 = <&pinctrl_uart2>;
- /delete-property/ fsl,uart-has-rtscts;
+ /delete-property/ uart-has-rtscts;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5 &pinctrl_uart5_rtscts>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
serial5 = &uart6;
serial6 = &uart7;
serial7 = &uart8;
+ sai1 = &sai1;
+ sai2 = &sai2;
+ sai3 = &sai3;
spi0 = &ecspi1;
spi1 = &ecspi2;
spi2 = &ecspi3;
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
- reg_3p0: regulator-3p0@120 {
+ reg_3p0: regulator-3p0 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd3p0";
regulator-min-microvolt = <2625000>;
anatop-enable-bit = <0>;
};
- reg_arm: regulator-vddcore@140 {
+ reg_arm: regulator-vddcore {
compatible = "fsl,anatop-regulator";
regulator-name = "cpu";
regulator-min-microvolt = <725000>;
anatop-max-voltage = <1450000>;
};
- reg_soc: regulator-vddsoc@140 {
+ reg_soc: regulator-vddsoc {
compatible = "fsl,anatop-regulator";
regulator-name = "vddsoc";
regulator-min-microvolt = <725000>;
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&bl {
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+};
+
+&adc1 {
+ status = "okay";
+};
+
+&adc2 {
+ status = "okay";
+};
+
+&fec1 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc: m41t0m6@68 {
+ compatible = "st,m41t00";
+ reg = <0x68>;
+ };
+};
+
+&lcdif {
+ display = <&display0>;
+ status = "okay";
+
+ display0: lcd-display {
+ bits-per-pixel = <16>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing_vga>;
+
+ /* Standard VGA timing */
+ timing_vga: 640x480 {
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <40>;
+ hfront-porch = <24>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ de-active = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbotg1 {
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
+ no-1-8-v;
+ cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ bl: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vref_1v8: regulator-vref-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&adc1 {
+ vref-supply = <®_vref_1v8>;
+};
+
+&adc2 {
+ vref-supply = <®_vref_1v8>;
+};
+
+&cpu0 {
+ arm-supply = <®_DCDC2>;
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
+ clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+ assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+ assigned-clock-rates = <0>, <100000000>;
+ phy-mode = "rmii";
+ phy-supply = <®_LDO1>;
+ fsl,magic-packet;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1 &pinctrl_i2c1_int>;
+ status = "okay";
+
+ ad7879@2c {
+ compatible = "adi,ad7879-1";
+ reg = <0x2c>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-max-pressure = <4096>;
+ adi,resistance-plate-x = <120>;
+ adi,first-conversion-delay = /bits/ 8 <3>;
+ adi,acquisition-time = /bits/ 8 <1>;
+ adi,median-filter-size = /bits/ 8 <2>;
+ adi,averaging = /bits/ 8 <1>;
+ adi,conversion-interval = /bits/ 8 <255>;
+ };
+
+ pmic@33 {
+ compatible = "ricoh,rn5t567";
+ reg = <0x33>;
+
+ regulators {
+ reg_DCDC1: DCDC1 { /* V1.0_SOC */
+ regulator-min-microvolt = <975000>;
+ regulator-max-microvolt = <1125000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_DCDC2: DCDC2 { /* V1.1_ARM */
+ regulator-min-microvolt = <975000>;
+ regulator-max-microvolt = <1125000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_DCDC3: DCDC3 { /* V1.8 */
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <1825000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_DCDC4: DCDC4 { /* V1.35_DRAM */
+ regulator-min-microvolt = <1325000>;
+ regulator-max-microvolt = <1375000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO1: LDO1 { /* PWR_EN_+V3.3_ETH */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_LDO2: LDO2 { /* +V1.8_SD */
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <3325000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO3: LDO3 { /* PWR_EN_+V3.3_LPSR */
+ regulator-min-microvolt = <3275000>;
+ regulator-max-microvolt = <3325000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO4: LDO4 { /* V1.8_LPSR */
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <1825000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO5: LDO5 { /* PWR_EN_+V3.3 */
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <1825000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif_dat
+ &pinctrl_lcdif_ctrl>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+};
+
+®_1p0d {
+ vin-supply = <®_DCDC3>;
+};
+
+&snvs_pwrkey {
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1 &pinctrl_uart1_ctrl2>;
+ assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+ uart-has-rtscts;
+ fsl,dte-mode;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ assigned-clocks = <&clks IMX7D_UART2_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+ uart-has-rtscts;
+ fsl,dte-mode;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+ fsl,dte-mode;
+};
+
+&usbotg1 {
+ dr_mode = "host";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4>;
+
+ pinctrl_gpio1: gpio1-grp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3 0x14 /* SODIMM 55 */
+ MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2 0x14 /* SODIMM 63 */
+ MX7D_PAD_SD1_RESET_B__GPIO5_IO2 0X14 /* SODIMM 73 */
+ MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 0X14 /* SODIMM 77 */
+ MX7D_PAD_EPDC_DATA09__GPIO2_IO9 0x14 /* SODIMM 89 */
+ MX7D_PAD_EPDC_DATA08__GPIO2_IO8 0x14 /* SODIMM 91 */
+ MX7D_PAD_LCD_RESET__GPIO3_IO4 0x14 /* SODIMM 93 */
+ MX7D_PAD_EPDC_DATA13__GPIO2_IO13 0x14 /* SODIMM 95 */
+ MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11 0x14 /* SODIMM 99 */
+ MX7D_PAD_EPDC_DATA10__GPIO2_IO10 0x14 /* SODIMM 105 */
+ MX7D_PAD_EPDC_DATA15__GPIO2_IO15 0x14 /* SODIMM 107 */
+ MX7D_PAD_EPDC_DATA00__GPIO2_IO0 0x14 /* SODIMM 111 */
+ MX7D_PAD_EPDC_DATA01__GPIO2_IO1 0x14 /* SODIMM 113 */
+ MX7D_PAD_EPDC_DATA02__GPIO2_IO2 0x14 /* SODIMM 115 */
+ MX7D_PAD_EPDC_DATA03__GPIO2_IO3 0x14 /* SODIMM 117 */
+ MX7D_PAD_EPDC_DATA04__GPIO2_IO4 0x14 /* SODIMM 119 */
+ MX7D_PAD_EPDC_DATA05__GPIO2_IO5 0x14 /* SODIMM 121 */
+ MX7D_PAD_EPDC_DATA06__GPIO2_IO6 0x14 /* SODIMM 123 */
+ MX7D_PAD_EPDC_DATA07__GPIO2_IO7 0x14 /* SODIMM 125 */
+ MX7D_PAD_EPDC_SDCE2__GPIO2_IO22 0x14 /* SODIMM 127 */
+ MX7D_PAD_UART3_RTS_B__GPIO4_IO6 0x14 /* SODIMM 131 */
+ MX7D_PAD_EPDC_GDRL__GPIO2_IO26 0x14 /* SODIMM 133 */
+ MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17 0x14 /* SODIMM 24 */
+ MX7D_PAD_SD2_DATA2__GPIO5_IO16 0x14 /* SODIMM 100 */
+ MX7D_PAD_SD2_DATA3__GPIO5_IO17 0x14 /* SODIMM 102 */
+ MX7D_PAD_EPDC_GDSP__GPIO2_IO27 0x14 /* SODIMM 104 */
+ MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14 /* SODIMM 106 */
+ MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x14 /* SODIMM 110 */
+ MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 0x14 /* SODIMM 112 */
+ MX7D_PAD_EPDC_SDCLK__GPIO2_IO16 0x14 /* SODIMM 114 */
+ MX7D_PAD_EPDC_SDLE__GPIO2_IO17 0x14 /* SODIMM 116 */
+ MX7D_PAD_EPDC_SDOE__GPIO2_IO18 0x14 /* SODIMM 118 */
+ MX7D_PAD_EPDC_SDSHR__GPIO2_IO19 0x14 /* SODIMM 120 */
+ MX7D_PAD_EPDC_SDCE0__GPIO2_IO20 0x14 /* SODIMM 122 */
+ MX7D_PAD_EPDC_SDCE1__GPIO2_IO21 0x14 /* SODIMM 124 */
+ MX7D_PAD_EPDC_DATA14__GPIO2_IO14 0x14 /* SODIMM 126 */
+ MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 0x14 /* SODIMM 128 */
+ MX7D_PAD_EPDC_SDCE3__GPIO2_IO23 0x14 /* SODIMM 130 */
+ MX7D_PAD_EPDC_GDCLK__GPIO2_IO24 0x14 /* SODIMM 132 */
+ MX7D_PAD_EPDC_GDOE__GPIO2_IO25 0x14 /* SODIMM 134 */
+ MX7D_PAD_EPDC_DATA12__GPIO2_IO12 0x14 /* SODIMM 150 */
+ MX7D_PAD_EPDC_DATA11__GPIO2_IO11 0x14 /* SODIMM 152 */
+ MX7D_PAD_SD2_CLK__GPIO5_IO12 0x14 /* SODIMM 184 */
+ MX7D_PAD_SD2_CMD__GPIO5_IO13 0x14 /* SODIMM 186 */
+ >;
+ };
+
+ pinctrl_gpio2: gpio2-grp { /* On X22 Camera interface */
+ fsl,pins = <
+ MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x14 /* SODIMM 65 */
+ MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x14 /* SODIMM 69 */
+ MX7D_PAD_SD1_WP__GPIO5_IO1 0x14 /* SODIMM 71 */
+ MX7D_PAD_I2C4_SDA__GPIO4_IO15 0x14 /* SODIMM 75 */
+ MX7D_PAD_ECSPI1_MISO__GPIO4_IO18 0x14 /* SODIMM 79 */
+ MX7D_PAD_I2C3_SCL__GPIO4_IO12 0x14 /* SODIMM 81 */
+ MX7D_PAD_ECSPI2_MISO__GPIO4_IO22 0x14 /* SODIMM 85 */
+ MX7D_PAD_ECSPI1_SS0__GPIO4_IO19 0x14 /* SODIMM 97 */
+ MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16 0x14 /* SODIMM 101 */
+ MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17 0x14 /* SODIMM 103 */
+ MX7D_PAD_I2C3_SDA__GPIO4_IO13 0x14 /* SODIMM 94 */
+ MX7D_PAD_I2C4_SCL__GPIO4_IO14 0x14 /* SODIMM 96 */
+ MX7D_PAD_SD2_RESET_B__GPIO5_IO11 0x14 /* SODIMM 98 */
+ >;
+ };
+
+ pinctrl_gpio3: gpio3-grp { /* LCD 18-23 */
+ fsl,pins = <
+ MX7D_PAD_LCD_DATA18__GPIO3_IO23 0x14 /* SODIMM 136 */
+ MX7D_PAD_LCD_DATA19__GPIO3_IO24 0x14 /* SODIMM 138 */
+ MX7D_PAD_LCD_DATA20__GPIO3_IO25 0x14 /* SODIMM 140 */
+ MX7D_PAD_LCD_DATA21__GPIO3_IO26 0x14 /* SODIMM 142 */
+ MX7D_PAD_LCD_DATA22__GPIO3_IO27 0x14 /* SODIMM 146 */
+ MX7D_PAD_LCD_DATA23__GPIO3_IO28 0x14 /* SODIMM 148 */
+ >;
+ };
+
+ pinctrl_gpio4: gpio4-grp { /* Alternatively CAN2 */
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO15__GPIO1_IO15 0x14 /* SODIMM 178 */
+ MX7D_PAD_GPIO1_IO14__GPIO1_IO14 0x14 /* SODIMM 188 */
+ >;
+ };
+
+ pinctrl_i2c1_int: i2c1-int-grp { /* PMIC / TOUCH */
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x79
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_CRS__GPIO7_IO14 0x14
+ MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x73
+ MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x73
+ MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x73
+ MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER 0x73
+
+ MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x73
+ MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x73
+ MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x73
+ MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x73
+ MX7D_PAD_SD2_CD_B__ENET1_MDIO 0x3
+ MX7D_PAD_SD2_WP__ENET1_MDC 0x3
+ >;
+ };
+
+ pinctrl_ecspi3_cs: ecspi3-cs-grp {
+ fsl,pins = <
+ MX7D_PAD_I2C2_SDA__GPIO4_IO11 0x14
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3-grp {
+ fsl,pins = <
+ MX7D_PAD_I2C1_SCL__ECSPI3_MISO 0x2
+ MX7D_PAD_I2C1_SDA__ECSPI3_MOSI 0x2
+ MX7D_PAD_I2C2_SCL__ECSPI3_SCLK 0x2
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX 0x59
+ MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX 0x59
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpmi-nand-grp {
+ fsl,pins = <
+ MX7D_PAD_SD3_CLK__NAND_CLE 0x71
+ MX7D_PAD_SD3_CMD__NAND_ALE 0x71
+ MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B 0x71
+ MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B 0x71
+ MX7D_PAD_SAI1_TX_DATA__NAND_READY_B 0x74
+ MX7D_PAD_SD3_STROBE__NAND_RE_B 0x71
+ MX7D_PAD_SD3_RESET_B__NAND_WE_B 0x71
+ MX7D_PAD_SD3_DATA0__NAND_DATA00 0x71
+ MX7D_PAD_SD3_DATA1__NAND_DATA01 0x71
+ MX7D_PAD_SD3_DATA2__NAND_DATA02 0x71
+ MX7D_PAD_SD3_DATA3__NAND_DATA03 0x71
+ MX7D_PAD_SD3_DATA4__NAND_DATA04 0x71
+ MX7D_PAD_SD3_DATA5__NAND_DATA05 0x71
+ MX7D_PAD_SD3_DATA6__NAND_DATA06 0x71
+ MX7D_PAD_SD3_DATA7__NAND_DATA07 0x71
+ >;
+ };
+
+ pinctrl_i2c4: i2c4-grp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA 0x4000007f
+ MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_lcdif_dat: lcdif-dat-grp {
+ fsl,pins = <
+ MX7D_PAD_LCD_DATA00__LCD_DATA0 0x79
+ MX7D_PAD_LCD_DATA01__LCD_DATA1 0x79
+ MX7D_PAD_LCD_DATA02__LCD_DATA2 0x79
+ MX7D_PAD_LCD_DATA03__LCD_DATA3 0x79
+ MX7D_PAD_LCD_DATA04__LCD_DATA4 0x79
+ MX7D_PAD_LCD_DATA05__LCD_DATA5 0x79
+ MX7D_PAD_LCD_DATA06__LCD_DATA6 0x79
+ MX7D_PAD_LCD_DATA07__LCD_DATA7 0x79
+ MX7D_PAD_LCD_DATA08__LCD_DATA8 0x79
+ MX7D_PAD_LCD_DATA09__LCD_DATA9 0x79
+ MX7D_PAD_LCD_DATA10__LCD_DATA10 0x79
+ MX7D_PAD_LCD_DATA11__LCD_DATA11 0x79
+ MX7D_PAD_LCD_DATA12__LCD_DATA12 0x79
+ MX7D_PAD_LCD_DATA13__LCD_DATA13 0x79
+ MX7D_PAD_LCD_DATA14__LCD_DATA14 0x79
+ MX7D_PAD_LCD_DATA15__LCD_DATA15 0x79
+ MX7D_PAD_LCD_DATA16__LCD_DATA16 0x79
+ MX7D_PAD_LCD_DATA17__LCD_DATA17 0x79
+ >;
+ };
+
+ pinctrl_lcdif_dat_24: lcdif-dat-24-grp {
+ fsl,pins = <
+ MX7D_PAD_LCD_DATA18__LCD_DATA18 0x79
+ MX7D_PAD_LCD_DATA19__LCD_DATA19 0x79
+ MX7D_PAD_LCD_DATA20__LCD_DATA20 0x79
+ MX7D_PAD_LCD_DATA21__LCD_DATA21 0x79
+ MX7D_PAD_LCD_DATA22__LCD_DATA22 0x79
+ MX7D_PAD_LCD_DATA23__LCD_DATA23 0x79
+ >;
+ };
+
+ pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
+ fsl,pins = <
+ MX7D_PAD_LCD_CLK__LCD_CLK 0x79
+ MX7D_PAD_LCD_ENABLE__LCD_ENABLE 0x79
+ MX7D_PAD_LCD_VSYNC__LCD_VSYNC 0x79
+ MX7D_PAD_LCD_HSYNC__LCD_HSYNC 0x79
+ >;
+ };
+
+ pinctrl_pwm1: pwm1-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO08__PWM1_OUT 0x79
+ >;
+ };
+
+ pinctrl_pwm2: pwm2-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO09__PWM2_OUT 0x79
+ >;
+ };
+
+ pinctrl_pwm3: pwm3-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO10__PWM3_OUT 0x79
+ >;
+ };
+
+ pinctrl_pwm4: pwm4-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO11__PWM4_OUT 0x79
+ >;
+ };
+
+ pinctrl_uart1: uart1-grp {
+ fsl,pins = <
+ MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX 0x79
+ MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX 0x79
+ MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS 0x79
+ MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS 0x79
+ >;
+ };
+
+ pinctrl_uart1_ctrl1: uart1-ctrl1-grp {
+ fsl,pins = <
+ MX7D_PAD_SD2_DATA1__GPIO5_IO15 0x14 /* DCD */
+ MX7D_PAD_SD2_DATA0__GPIO5_IO14 0x14 /* DTR */
+ >;
+ };
+
+ pinctrl_uart2: uart2-grp {
+ fsl,pins = <
+ MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX 0x79
+ MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX 0x79
+ MX7D_PAD_SAI2_RX_DATA__UART2_DTE_RTS 0x79
+ MX7D_PAD_SAI2_TX_DATA__UART2_DTE_CTS 0x79
+ >;
+ };
+ pinctrl_uart3: uart3-grp {
+ fsl,pins = <
+ MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX 0x79
+ MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX 0x79
+ >;
+ };
+
+ pinctrl_usbotg2_reg: gpio-usbotg2-vbus {
+ fsl,pins = <
+ MX7D_PAD_UART3_CTS_B__GPIO4_IO7 0x14 /* SODIMM 129 USBH PEN */
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1-grp {
+ fsl,pins = <
+ MX7D_PAD_SD1_CMD__SD1_CMD 0x59
+ MX7D_PAD_SD1_CLK__SD1_CLK 0x19
+ MX7D_PAD_SD1_DATA0__SD1_DATA0 0x59
+ MX7D_PAD_SD1_DATA1__SD1_DATA1 0x59
+ MX7D_PAD_SD1_DATA2__SD1_DATA2 0x59
+ MX7D_PAD_SD1_DATA3__SD1_DATA3 0x59
+ >;
+ };
+
+ pinctrl_sai1: sai1-grp {
+ fsl,pins = <
+ MX7D_PAD_SAI1_MCLK__SAI1_MCLK 0x1f
+ MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK 0x1f
+ MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC 0x1f
+ MX7D_PAD_ENET1_COL__SAI1_TX_DATA0 0x30
+ MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0 0x1f
+ >;
+ };
+};
+
+&iomuxc_lpsr {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_lpsr>;
+
+ pinctrl_gpio_lpsr: gpio1-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO01__GPIO1_IO1 0x59
+ MX7D_PAD_GPIO1_IO02__GPIO1_IO2 0x59
+ MX7D_PAD_GPIO1_IO03__GPIO1_IO3 0x59
+ >;
+ };
+
+ pinctrl_i2c1: i2c1-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO05__I2C1_SDA 0x4000007f
+ MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_cd_usdhc1: usdhc1-cd-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO00__GPIO1_IO0 0x59 /* CD */
+ >;
+ };
+
+ pinctrl_uart1_ctrl2: uart1-ctrl2-grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO07__GPIO1_IO7 0x14 /* DSR */
+ MX7D_PAD_GPIO1_IO06__GPIO1_IO6 0x14 /* RI */
+ >;
+ };
+};
/dts-v1/;
-#include <dt-bindings/input/input.h>
#include "imx7d.dtsi"
/ {
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-eval-v3.dtsi"
+
+/ {
+ model = "Toradex Colibri iMX7D on Colibri Evaluation Board V3";
+ compatible = "toradex,colibri-imx7d-eval-v3", "toradex,colibri-imx7d",
+ "fsl,imx7d";
+
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg2_reg>;
+ regulator-name = "VCC_USB[1-4]";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx7d.dtsi"
+#include "imx7-colibri.dtsi"
+
+/ {
+ memory {
+ reg = <0x80000000 0x20000000>;
+ };
+};
+
+&usbotg2 {
+ dr_mode = "host";
+};
/dts-v1/;
-#include <dt-bindings/input/input.h>
#include "imx7d.dtsi"
/ {
pinctrl-0 = <&pinctrl_uart6>;
assigned-clocks = <&clks IMX7D_UART6_ROOT_SRC>;
assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
#define MX7D_PAD_UART2_RX_DATA__GPIO4_IO2 0x0130 0x03A0 0x0000 0x5 0x0
#define MX7D_PAD_UART2_RX_DATA__ENET2_MDIO 0x0130 0x03A0 0x0000 0x6 0x0
#define MX7D_PAD_UART2_TX_DATA__UART2_DCE_TX 0x0134 0x03A4 0x0000 0x0 0x0
-#define MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX 0x0134 0x03A4 0x0000 0x0 0x0
+#define MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX 0x0134 0x03A4 0x06FC 0x0 0x3
#define MX7D_PAD_UART2_TX_DATA__I2C2_SDA 0x0134 0x03A4 0x05E0 0x1 0x0
#define MX7D_PAD_UART2_TX_DATA__SAI3_RX_DATA0 0x0134 0x03A4 0x06C8 0x2 0x0
#define MX7D_PAD_UART2_TX_DATA__ECSPI1_RDY 0x0134 0x03A4 0x0000 0x3 0x0
/dts-v1/;
-#include <dt-bindings/input/input.h>
#include "imx7d.dtsi"
/ {
arm-supply = <&sw1a_reg>;
};
+&ecspi3 {
+ fsl,spi-num-chipselects = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ tsc2046@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ pinctrl-names ="default";
+ pinctrl-0 = <&pinctrl_tsc2046_pendown>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <29 0>;
+ pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+ ti,x-min = /bits/ 16 <0>;
+ ti,x-max = /bits/ 16 <0>;
+ ti,y-min = /bits/ 16 <0>;
+ ti,y-max = /bits/ 16 <0>;
+ ti,pressure-max = /bits/ 16 <0>;
+ ti,x-plat-ohms = /bits/ 16 <400>;
+ wakeup-source;
+ };
+};
+
&fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet1>;
};
};
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+
+ timing0: timing0 {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <8>;
+ hback-porch = <4>;
+ hsync-len = <41>;
+ vback-porch = <2>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
imx7d-sdb {
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO 0x2
+ MX7D_PAD_SAI2_TX_BCLK__ECSPI3_MOSI 0x2
+ MX7D_PAD_SAI2_RX_DATA__ECSPI3_SCLK 0x2
+ MX7D_PAD_SD2_CD_B__GPIO5_IO9 0x59
+ >;
+ };
+
pinctrl_enet1: enet1grp {
fsl,pins = <
MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x3
>;
};
+ pinctrl_lcdif: lcdifgrp {
+ fsl,pins = <
+ MX7D_PAD_LCD_DATA00__LCD_DATA0 0x79
+ MX7D_PAD_LCD_DATA01__LCD_DATA1 0x79
+ MX7D_PAD_LCD_DATA02__LCD_DATA2 0x79
+ MX7D_PAD_LCD_DATA03__LCD_DATA3 0x79
+ MX7D_PAD_LCD_DATA04__LCD_DATA4 0x79
+ MX7D_PAD_LCD_DATA05__LCD_DATA5 0x79
+ MX7D_PAD_LCD_DATA06__LCD_DATA6 0x79
+ MX7D_PAD_LCD_DATA07__LCD_DATA7 0x79
+ MX7D_PAD_LCD_DATA08__LCD_DATA8 0x79
+ MX7D_PAD_LCD_DATA09__LCD_DATA9 0x79
+ MX7D_PAD_LCD_DATA10__LCD_DATA10 0x79
+ MX7D_PAD_LCD_DATA11__LCD_DATA11 0x79
+ MX7D_PAD_LCD_DATA12__LCD_DATA12 0x79
+ MX7D_PAD_LCD_DATA13__LCD_DATA13 0x79
+ MX7D_PAD_LCD_DATA14__LCD_DATA14 0x79
+ MX7D_PAD_LCD_DATA15__LCD_DATA15 0x79
+ MX7D_PAD_LCD_DATA16__LCD_DATA16 0x79
+ MX7D_PAD_LCD_DATA17__LCD_DATA17 0x79
+ MX7D_PAD_LCD_DATA18__LCD_DATA18 0x79
+ MX7D_PAD_LCD_DATA19__LCD_DATA19 0x79
+ MX7D_PAD_LCD_DATA20__LCD_DATA20 0x79
+ MX7D_PAD_LCD_DATA21__LCD_DATA21 0x79
+ MX7D_PAD_LCD_DATA22__LCD_DATA22 0x79
+ MX7D_PAD_LCD_DATA23__LCD_DATA23 0x79
+ MX7D_PAD_LCD_CLK__LCD_CLK 0x79
+ MX7D_PAD_LCD_ENABLE__LCD_ENABLE 0x79
+ MX7D_PAD_LCD_VSYNC__LCD_VSYNC 0x79
+ MX7D_PAD_LCD_HSYNC__LCD_HSYNC 0x79
+ MX7D_PAD_LCD_RESET__LCD_RESET 0x79
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO01__PWM1_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_tsc2046_pendown: tsc2046_pendown {
+ fsl,pins = <
+ MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x59
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
>;
};
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B 0x74
+ >;
+ };
};
};
/*
* Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2016 Toradex AG
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/clock/imx7d-clock.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include "imx7d-pinfunc.h"
-#include "skeleton.dtsi"
+#include "imx7s.dtsi"
/ {
- aliases {
- gpio0 = &gpio1;
- gpio1 = &gpio2;
- gpio2 = &gpio3;
- gpio3 = &gpio4;
- gpio4 = &gpio5;
- gpio5 = &gpio6;
- gpio6 = &gpio7;
- i2c0 = &i2c1;
- i2c1 = &i2c2;
- i2c2 = &i2c3;
- i2c3 = &i2c4;
- mmc0 = &usdhc1;
- mmc1 = &usdhc2;
- mmc2 = &usdhc3;
- serial0 = &uart1;
- serial1 = &uart2;
- serial2 = &uart3;
- serial3 = &uart4;
- serial4 = &uart5;
- serial5 = &uart6;
- serial6 = &uart7;
- };
-
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- operating-points = <
- /* KHz uV */
- 996000 1075000
- 792000 975000
- >;
- clock-latency = <61036>; /* two CLK32 periods */
- clocks = <&clks IMX7D_CLK_ARM>;
- };
-
cpu1: cpu@1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
};
};
- intc: interrupt-controller@31001000 {
- compatible = "arm,cortex-a7-gic";
- #interrupt-cells = <3>;
- interrupt-controller;
- reg = <0x31001000 0x1000>,
- <0x31002000 0x1000>,
- <0x31004000 0x2000>,
- <0x31006000 0x2000>;
- };
-
- ckil: clock-cki {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- clock-output-names = "ckil";
- };
-
- osc: clock-osc {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24000000>;
- clock-output-names = "osc";
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- interrupt-parent = <&intc>;
- };
-
- etr@30086000 {
- compatible = "arm,coresight-tmc", "arm,primecell";
- reg = <0x30086000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- port {
- etr_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&replicator_out_port1>;
- };
- };
- };
-
- tpiu@30087000 {
- compatible = "arm,coresight-tpiu", "arm,primecell";
- reg = <0x30087000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- port {
- tpiu_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&replicator_out_port1>;
- };
- };
- };
-
- replicator {
- /*
- * non-configurable replicators don't show up on the
- * AMBA bus. As such no need to add "arm,primecell"
- */
- compatible = "arm,coresight-replicator";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* replicator output ports */
- port@0 {
- reg = <0>;
- replicator_out_port0: endpoint {
- remote-endpoint = <&tpiu_in_port>;
- };
- };
-
- port@1 {
- reg = <1>;
- replicator_out_port1: endpoint {
- remote-endpoint = <&etr_in_port>;
- };
- };
-
- /* replicator input port */
- port@2 {
- reg = <0>;
- replicator_in_port0: endpoint {
- slave-mode;
- remote-endpoint = <&etf_out_port>;
- };
- };
- };
- };
-
- etf@30084000 {
- compatible = "arm,coresight-tmc", "arm,primecell";
- reg = <0x30084000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- etf_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&hugo_funnel_out_port0>;
- };
- };
-
- port@1 {
- reg = <0>;
- etf_out_port: endpoint {
- remote-endpoint = <&replicator_in_port0>;
- };
- };
- };
- };
-
- funnel@30083000 {
- compatible = "arm,coresight-funnel", "arm,primecell";
- reg = <0x30083000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* funnel input ports */
- port@0 {
- reg = <0>;
- hugo_funnel_in_port0: endpoint {
- slave-mode;
- remote-endpoint = <&ca_funnel_out_port0>;
- };
- };
-
- port@1 {
- reg = <1>;
- hugo_funnel_in_port1: endpoint {
- slave-mode; /* M4 input */
- };
- };
-
- port@2 {
- reg = <0>;
- hugo_funnel_out_port0: endpoint {
- remote-endpoint = <&etf_in_port>;
- };
- };
-
- /* the other input ports are not connect to anything */
- };
- };
-
- funnel@30041000 {
- compatible = "arm,coresight-funnel", "arm,primecell";
- reg = <0x30041000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* funnel input ports */
- port@0 {
- reg = <0>;
- ca_funnel_in_port0: endpoint {
- slave-mode;
- remote-endpoint = <&etm0_out_port>;
- };
- };
-
- port@1 {
- reg = <1>;
- ca_funnel_in_port1: endpoint {
- slave-mode;
- remote-endpoint = <&etm1_out_port>;
- };
- };
-
- /* funnel output port */
- port@2 {
- reg = <0>;
- ca_funnel_out_port0: endpoint {
- remote-endpoint = <&hugo_funnel_in_port0>;
- };
- };
-
- /* the other input ports are not connect to anything */
- };
- };
-
- etm@3007c000 {
- compatible = "arm,coresight-etm3x", "arm,primecell";
- reg = <0x3007c000 0x1000>;
- cpu = <&cpu0>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- port {
- etm0_out_port: endpoint {
- remote-endpoint = <&ca_funnel_in_port0>;
- };
- };
- };
-
etm@3007d000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x3007d000 0x1000>;
};
};
};
+};
- soc {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- interrupt-parent = <&intc>;
- ranges;
-
- aips1: aips-bus@30000000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x30000000 0x400000>;
- ranges;
-
- gpio1: gpio@30200000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30200000 0x10000>;
- interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, /* GPIO1_INT15_0 */
- <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; /* GPIO1_INT31_16 */
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio2: gpio@30210000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30210000 0x10000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio3: gpio@30220000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30220000 0x10000>;
- interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio4: gpio@30230000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30230000 0x10000>;
- interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio5: gpio@30240000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30240000 0x10000>;
- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio6: gpio@30250000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30250000 0x10000>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio7: gpio@30260000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30260000 0x10000>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- wdog1: wdog@30280000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x30280000 0x10000>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG1_ROOT_CLK>;
- };
-
- wdog2: wdog@30290000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x30290000 0x10000>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG2_ROOT_CLK>;
- status = "disabled";
- };
-
- wdog3: wdog@302a0000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x302a0000 0x10000>;
- interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG3_ROOT_CLK>;
- status = "disabled";
- };
-
- wdog4: wdog@302b0000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x302b0000 0x10000>;
- interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG4_ROOT_CLK>;
- status = "disabled";
- };
-
- iomuxc_lpsr: iomuxc-lpsr@302c0000 {
- compatible = "fsl,imx7d-iomuxc-lpsr";
- reg = <0x302c0000 0x10000>;
- fsl,input-sel = <&iomuxc>;
- };
-
- gpt1: gpt@302d0000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x302d0000 0x10000>;
- interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT1_ROOT_CLK>;
- clock-names = "ipg", "per";
- };
-
- gpt2: gpt@302e0000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x302e0000 0x10000>;
- interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT2_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- gpt3: gpt@302f0000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x302f0000 0x10000>;
- interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT3_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- gpt4: gpt@30300000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x30300000 0x10000>;
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT4_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- iomuxc: iomuxc@30330000 {
- compatible = "fsl,imx7d-iomuxc";
- reg = <0x30330000 0x10000>;
- };
-
- gpr: iomuxc-gpr@30340000 {
- compatible = "fsl,imx7d-iomuxc-gpr", "syscon";
- reg = <0x30340000 0x10000>;
- };
-
- ocotp: ocotp-ctrl@30350000 {
- compatible = "syscon";
- reg = <0x30350000 0x10000>;
- clocks = <&clks IMX7D_CLK_DUMMY>;
- status = "disabled";
- };
-
- anatop: anatop@30360000 {
- compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop",
- "syscon", "simple-bus";
- reg = <0x30360000 0x10000>;
- interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-
- reg_1p0d: regulator-vdd1p0d@210 {
- compatible = "fsl,anatop-regulator";
- regulator-name = "vdd1p0d";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1200000>;
- anatop-reg-offset = <0x210>;
- anatop-vol-bit-shift = <8>;
- anatop-vol-bit-width = <5>;
- anatop-min-bit-val = <8>;
- anatop-min-voltage = <800000>;
- anatop-max-voltage = <1200000>;
- anatop-enable-bit = <31>;
- };
- };
-
- snvs: snvs@30370000 {
- compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
- reg = <0x30370000 0x10000>;
-
- snvs_rtc: snvs-rtc-lp {
- compatible = "fsl,sec-v4.0-mon-rtc-lp";
- regmap = <&snvs>;
- offset = <0x34>;
- interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- snvs_poweroff: snvs-poweroff {
- compatible = "syscon-poweroff";
- regmap = <&snvs>;
- offset = <0x38>;
- mask = <0x60>;
- };
-
- snvs_pwrkey: snvs-powerkey {
- compatible = "fsl,sec-v4.0-pwrkey";
- regmap = <&snvs>;
- interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
- linux,keycode = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- clks: ccm@30380000 {
- compatible = "fsl,imx7d-ccm";
- reg = <0x30380000 0x10000>;
- interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
- #clock-cells = <1>;
- clocks = <&ckil>, <&osc>;
- clock-names = "ckil", "osc";
- };
-
- src: src@30390000 {
- compatible = "fsl,imx7d-src", "fsl,imx51-src", "syscon";
- reg = <0x30390000 0x10000>;
- interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
- #reset-cells = <1>;
- };
- };
-
- aips2: aips-bus@30400000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x30400000 0x400000>;
- ranges;
-
- adc1: adc@30610000 {
- compatible = "fsl,imx7d-adc";
- reg = <0x30610000 0x10000>;
- interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ADC_ROOT_CLK>;
- clock-names = "adc";
- status = "disabled";
- };
-
- adc2: adc@30620000 {
- compatible = "fsl,imx7d-adc";
- reg = <0x30620000 0x10000>;
- interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ADC_ROOT_CLK>;
- clock-names = "adc";
- status = "disabled";
- };
-
- pwm1: pwm@30660000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30660000 0x10000>;
- interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM1_ROOT_CLK>,
- <&clks IMX7D_PWM1_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm2: pwm@30670000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30670000 0x10000>;
- interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM2_ROOT_CLK>,
- <&clks IMX7D_PWM2_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm3: pwm@30680000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30680000 0x10000>;
- interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM3_ROOT_CLK>,
- <&clks IMX7D_PWM3_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm4: pwm@30690000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30690000 0x10000>;
- interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM4_ROOT_CLK>,
- <&clks IMX7D_PWM4_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- lcdif: lcdif@30730000 {
- compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
- reg = <0x30730000 0x10000>;
- interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>;
- clock-names = "pix", "axi", "disp_axi";
- status = "disabled";
- };
- };
-
- aips3: aips-bus@30800000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x30800000 0x400000>;
- ranges;
-
- uart1: serial@30860000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30860000 0x10000>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART1_ROOT_CLK>,
- <&clks IMX7D_UART1_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart2: serial@30890000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30890000 0x10000>;
- interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART2_ROOT_CLK>,
- <&clks IMX7D_UART2_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart3: serial@30880000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30880000 0x10000>;
- interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART3_ROOT_CLK>,
- <&clks IMX7D_UART3_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- flexcan1: can@30a00000 {
- compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
- reg = <0x30a00000 0x10000>;
- interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CAN1_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- flexcan2: can@30a10000 {
- compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
- reg = <0x30a10000 0x10000>;
- interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CAN2_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- i2c1: i2c@30a20000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a20000 0x10000>;
- interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C1_ROOT_CLK>;
- status = "disabled";
- };
-
- i2c2: i2c@30a30000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a30000 0x10000>;
- interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C2_ROOT_CLK>;
- status = "disabled";
- };
-
- i2c3: i2c@30a40000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a40000 0x10000>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C3_ROOT_CLK>;
- status = "disabled";
- };
-
- i2c4: i2c@30a50000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a50000 0x10000>;
- interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C4_ROOT_CLK>;
- status = "disabled";
- };
-
- uart4: serial@30a60000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a60000 0x10000>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART4_ROOT_CLK>,
- <&clks IMX7D_UART4_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart5: serial@30a70000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a70000 0x10000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART5_ROOT_CLK>,
- <&clks IMX7D_UART5_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart6: serial@30a80000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a80000 0x10000>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART6_ROOT_CLK>,
- <&clks IMX7D_UART6_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart7: serial@30a90000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a90000 0x10000>;
- interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART7_ROOT_CLK>,
- <&clks IMX7D_UART7_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- usbotg1: usb@30b10000 {
- compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
- reg = <0x30b10000 0x200>;
- interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_USB_CTRL_CLK>;
- fsl,usbphy = <&usbphynop1>;
- fsl,usbmisc = <&usbmisc1 0>;
- phy-clkgate-delay-us = <400>;
- status = "disabled";
- };
-
- usbotg2: usb@30b20000 {
- compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
- reg = <0x30b20000 0x200>;
- interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_USB_CTRL_CLK>;
- fsl,usbphy = <&usbphynop2>;
- fsl,usbmisc = <&usbmisc2 0>;
- phy-clkgate-delay-us = <400>;
- status = "disabled";
- };
-
- usbh: usb@30b30000 {
- compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
- reg = <0x30b30000 0x200>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_USB_CTRL_CLK>;
- fsl,usbphy = <&usbphynop3>;
- fsl,usbmisc = <&usbmisc3 0>;
- phy_type = "hsic";
- dr_mode = "host";
- phy-clkgate-delay-us = <400>;
- status = "disabled";
- };
-
- usbmisc1: usbmisc@30b10200 {
- #index-cells = <1>;
- compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
- reg = <0x30b10200 0x200>;
- };
-
- usbmisc2: usbmisc@30b20200 {
- #index-cells = <1>;
- compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
- reg = <0x30b20200 0x200>;
- };
-
- usbmisc3: usbmisc@30b30200 {
- #index-cells = <1>;
- compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
- reg = <0x30b30200 0x200>;
- };
-
- usbphynop1: usbphynop1 {
- compatible = "usb-nop-xceiv";
- clocks = <&clks IMX7D_USB_PHY1_CLK>;
- clock-names = "main_clk";
- };
-
- usbphynop2: usbphynop2 {
- compatible = "usb-nop-xceiv";
- clocks = <&clks IMX7D_USB_PHY2_CLK>;
- clock-names = "main_clk";
- };
-
- usbphynop3: usbphynop3 {
- compatible = "usb-nop-xceiv";
- clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
- clock-names = "main_clk";
- };
-
- usdhc1: usdhc@30b40000 {
- compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
- reg = <0x30b40000 0x10000>;
- interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_USDHC1_ROOT_CLK>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
+&aips3 {
+ usbotg2: usb@30b20000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b20000 0x200>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop2>;
+ fsl,usbmisc = <&usbmisc2 0>;
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
- usdhc2: usdhc@30b50000 {
- compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
- reg = <0x30b50000 0x10000>;
- interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_USDHC2_ROOT_CLK>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
+ usbmisc2: usbmisc@30b20200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b20200 0x200>;
+ };
- usdhc3: usdhc@30b60000 {
- compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
- reg = <0x30b60000 0x10000>;
- interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_USDHC3_ROOT_CLK>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_PHY2_CLK>;
+ clock-names = "main_clk";
+ };
- fec1: ethernet@30be0000 {
- compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
- reg = <0x30be0000 0x10000>;
- interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
- <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
- <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
- clock-names = "ipg", "ahb", "ptp",
- "enet_clk_ref", "enet_out";
- fsl,num-tx-queues=<3>;
- fsl,num-rx-queues=<3>;
- status = "disabled";
- };
+ fec2: ethernet@30bf0000 {
+ compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+ reg = <0x30bf0000 0x10000>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET2_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+ <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<3>;
+ fsl,num-rx-queues=<3>;
+ status = "disabled";
+ };
+};
- fec2: ethernet@30bf0000 {
- compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
- reg = <0x30bf0000 0x10000>;
- interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET2_TIME_ROOT_CLK>,
- <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
- <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
- clock-names = "ipg", "ahb", "ptp",
- "enet_clk_ref", "enet_out";
- fsl,num-tx-queues=<3>;
- fsl,num-rx-queues=<3>;
- status = "disabled";
- };
+&ca_funnel_ports {
+ port@1 {
+ reg = <1>;
+ ca_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm1_out_port>;
};
};
};
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-eval-v3.dtsi"
+
+/ {
+ model = "Toradex Colibri iMX7S on Colibri Evaluation Board V3";
+ compatible = "toradex,colibri-imx7s-eval-v3", "toradex,colibri-imx7s",
+ "fsl,imx7s";
+};
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx7s.dtsi"
+#include "imx7-colibri.dtsi"
+
+/ {
+ memory {
+ reg = <0x80000000 0x10000000>;
+ };
+};
--- /dev/null
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/imx7d-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "imx7d-pinfunc.h"
+#include "skeleton.dtsi"
+
+/ {
+ aliases {
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ gpio5 = &gpio6;
+ gpio6 = &gpio7;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ serial6 = &uart7;
+ spi0 = &ecspi1;
+ spi1 = &ecspi2;
+ spi2 = &ecspi3;
+ spi3 = &ecspi4;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ operating-points = <
+ /* KHz uV */
+ 996000 1075000
+ 792000 975000
+ >;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clks IMX7D_CLK_ARM>;
+ };
+ };
+
+ intc: interrupt-controller@31001000 {
+ compatible = "arm,cortex-a7-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x31001000 0x1000>,
+ <0x31002000 0x1000>,
+ <0x31004000 0x2000>,
+ <0x31006000 0x2000>;
+ };
+
+ ckil: clock-cki {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "ckil";
+ };
+
+ osc: clock-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc";
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ interrupt-parent = <&intc>;
+ };
+
+ etr@30086000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x30086000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ port {
+ etr_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&replicator_out_port1>;
+ };
+ };
+ };
+
+ tpiu@30087000 {
+ compatible = "arm,coresight-tpiu", "arm,primecell";
+ reg = <0x30087000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ port {
+ tpiu_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&replicator_out_port1>;
+ };
+ };
+ };
+
+ replicator {
+ /*
+ * non-configurable replicators don't show up on the
+ * AMBA bus. As such no need to add "arm,primecell"
+ */
+ compatible = "arm,coresight-replicator";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* replicator output ports */
+ port@0 {
+ reg = <0>;
+ replicator_out_port0: endpoint {
+ remote-endpoint = <&tpiu_in_port>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ replicator_out_port1: endpoint {
+ remote-endpoint = <&etr_in_port>;
+ };
+ };
+
+ /* replicator input port */
+ port@2 {
+ reg = <0>;
+ replicator_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etf_out_port>;
+ };
+ };
+ };
+ };
+
+ etf@30084000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x30084000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ etf_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&hugo_funnel_out_port0>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ etf_out_port: endpoint {
+ remote-endpoint = <&replicator_in_port0>;
+ };
+ };
+ };
+ };
+
+ funnel@30083000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0x30083000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* funnel input ports */
+ port@0 {
+ reg = <0>;
+ hugo_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&ca_funnel_out_port0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ hugo_funnel_in_port1: endpoint {
+ slave-mode; /* M4 input */
+ };
+ };
+
+ port@2 {
+ reg = <0>;
+ hugo_funnel_out_port0: endpoint {
+ remote-endpoint = <&etf_in_port>;
+ };
+ };
+
+ /* the other input ports are not connect to anything */
+ };
+ };
+
+ funnel@30041000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0x30041000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ ca_funnel_ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* funnel input ports */
+ port@0 {
+ reg = <0>;
+ ca_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm0_out_port>;
+ };
+ };
+
+ /* funnel output port */
+ port@2 {
+ reg = <0>;
+ ca_funnel_out_port0: endpoint {
+ remote-endpoint = <&hugo_funnel_in_port0>;
+ };
+ };
+
+ /* the other input ports are not connect to anything */
+ };
+ };
+
+ etm@3007c000 {
+ compatible = "arm,coresight-etm3x", "arm,primecell";
+ reg = <0x3007c000 0x1000>;
+ cpu = <&cpu0>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm0_out_port: endpoint {
+ remote-endpoint = <&ca_funnel_in_port0>;
+ };
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&intc>;
+ ranges;
+
+ aips1: aips-bus@30000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30000000 0x400000>;
+ ranges;
+
+ gpio1: gpio@30200000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30200000 0x10000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, /* GPIO1_INT15_0 */
+ <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; /* GPIO1_INT31_16 */
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@30210000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30210000 0x10000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@30220000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30220000 0x10000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@30230000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30230000 0x10000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio5: gpio@30240000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30240000 0x10000>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio6: gpio@30250000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30250000 0x10000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio7: gpio@30260000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30260000 0x10000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wdog1: wdog@30280000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x30280000 0x10000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG1_ROOT_CLK>;
+ };
+
+ wdog2: wdog@30290000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x30290000 0x10000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG2_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ wdog3: wdog@302a0000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x302a0000 0x10000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG3_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ wdog4: wdog@302b0000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x302b0000 0x10000>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG4_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+ compatible = "fsl,imx7d-iomuxc-lpsr";
+ reg = <0x302c0000 0x10000>;
+ fsl,input-sel = <&iomuxc>;
+ };
+
+ gpt1: gpt@302d0000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x302d0000 0x10000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ };
+
+ gpt2: gpt@302e0000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x302e0000 0x10000>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ gpt3: gpt@302f0000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x302f0000 0x10000>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ gpt4: gpt@30300000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x30300000 0x10000>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ iomuxc: iomuxc@30330000 {
+ compatible = "fsl,imx7d-iomuxc";
+ reg = <0x30330000 0x10000>;
+ };
+
+ gpr: iomuxc-gpr@30340000 {
+ compatible = "fsl,imx7d-iomuxc-gpr", "syscon";
+ reg = <0x30340000 0x10000>;
+ };
+
+ ocotp: ocotp-ctrl@30350000 {
+ compatible = "syscon";
+ reg = <0x30350000 0x10000>;
+ clocks = <&clks IMX7D_CLK_DUMMY>;
+ status = "disabled";
+ };
+
+ anatop: anatop@30360000 {
+ compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop",
+ "syscon", "simple-bus";
+ reg = <0x30360000 0x10000>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+
+ reg_1p0d: regulator-vdd1p0d {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd1p0d";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1200000>;
+ anatop-reg-offset = <0x210>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <8>;
+ anatop-min-voltage = <800000>;
+ anatop-max-voltage = <1200000>;
+ anatop-enable-bit = <31>;
+ };
+ };
+
+ snvs: snvs@30370000 {
+ compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
+ reg = <0x30370000 0x10000>;
+
+ snvs_rtc: snvs-rtc-lp {
+ compatible = "fsl,sec-v4.0-mon-rtc-lp";
+ regmap = <&snvs>;
+ offset = <0x34>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ snvs_poweroff: snvs-poweroff {
+ compatible = "syscon-poweroff";
+ regmap = <&snvs>;
+ offset = <0x38>;
+ mask = <0x60>;
+ };
+
+ snvs_pwrkey: snvs-powerkey {
+ compatible = "fsl,sec-v4.0-pwrkey";
+ regmap = <&snvs>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ linux,keycode = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ clks: ccm@30380000 {
+ compatible = "fsl,imx7d-ccm";
+ reg = <0x30380000 0x10000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ #clock-cells = <1>;
+ clocks = <&ckil>, <&osc>;
+ clock-names = "ckil", "osc";
+ };
+
+ src: src@30390000 {
+ compatible = "fsl,imx7d-src", "fsl,imx51-src", "syscon";
+ reg = <0x30390000 0x10000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ };
+ };
+
+ aips2: aips-bus@30400000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30400000 0x400000>;
+ ranges;
+
+ adc1: adc@30610000 {
+ compatible = "fsl,imx7d-adc";
+ reg = <0x30610000 0x10000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
+ adc2: adc@30620000 {
+ compatible = "fsl,imx7d-adc";
+ reg = <0x30620000 0x10000>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
+ ecspi4: ecspi@30630000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi";
+ reg = <0x30630000 0x10000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ECSPI4_ROOT_CLK>,
+ <&clks IMX7D_ECSPI4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ pwm1: pwm@30660000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30660000 0x10000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM1_ROOT_CLK>,
+ <&clks IMX7D_PWM1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@30670000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30670000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM2_ROOT_CLK>,
+ <&clks IMX7D_PWM2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@30680000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30680000 0x10000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM3_ROOT_CLK>,
+ <&clks IMX7D_PWM3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm4: pwm@30690000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30690000 0x10000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM4_ROOT_CLK>,
+ <&clks IMX7D_PWM4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ lcdif: lcdif@30730000 {
+ compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
+ reg = <0x30730000 0x10000>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>;
+ clock-names = "pix", "axi", "disp_axi";
+ status = "disabled";
+ };
+ };
+
+ aips3: aips-bus@30800000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30800000 0x400000>;
+ ranges;
+
+ ecspi1: ecspi@30820000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi";
+ reg = <0x30820000 0x10000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ECSPI1_ROOT_CLK>,
+ <&clks IMX7D_ECSPI1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi2: ecspi@30830000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi";
+ reg = <0x30830000 0x10000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ECSPI2_ROOT_CLK>,
+ <&clks IMX7D_ECSPI2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi3: ecspi@30840000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi";
+ reg = <0x30840000 0x10000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ECSPI3_ROOT_CLK>,
+ <&clks IMX7D_ECSPI3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart1: serial@30860000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30860000 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART1_ROOT_CLK>,
+ <&clks IMX7D_UART1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart2: serial@30890000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30890000 0x10000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART2_ROOT_CLK>,
+ <&clks IMX7D_UART2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart3: serial@30880000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30880000 0x10000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART3_ROOT_CLK>,
+ <&clks IMX7D_UART3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ flexcan1: can@30a00000 {
+ compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x30a00000 0x10000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CAN1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ flexcan2: can@30a10000 {
+ compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x30a10000 0x10000>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CAN2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ i2c1: i2c@30a20000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a20000 0x10000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C1_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@30a30000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a30000 0x10000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C2_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@30a40000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a40000 0x10000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C3_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@30a50000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a50000 0x10000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C4_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ uart4: serial@30a60000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a60000 0x10000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART4_ROOT_CLK>,
+ <&clks IMX7D_UART4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart5: serial@30a70000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a70000 0x10000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART5_ROOT_CLK>,
+ <&clks IMX7D_UART5_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart6: serial@30a80000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a80000 0x10000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART6_ROOT_CLK>,
+ <&clks IMX7D_UART6_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart7: serial@30a90000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a90000 0x10000>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART7_ROOT_CLK>,
+ <&clks IMX7D_UART7_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ usbotg1: usb@30b10000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b10000 0x200>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop1>;
+ fsl,usbmisc = <&usbmisc1 0>;
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
+
+ usbh: usb@30b30000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b30000 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop3>;
+ fsl,usbmisc = <&usbmisc3 0>;
+ phy_type = "hsic";
+ dr_mode = "host";
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
+
+ usbmisc1: usbmisc@30b10200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b10200 0x200>;
+ };
+
+ usbmisc3: usbmisc@30b30200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b30200 0x200>;
+ };
+
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_PHY1_CLK>;
+ clock-names = "main_clk";
+ };
+
+ usbphynop3: usbphynop3 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
+ clock-names = "main_clk";
+ };
+
+ usdhc1: usdhc@30b40000 {
+ compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x30b40000 0x10000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_USDHC1_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc2: usdhc@30b50000 {
+ compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x30b50000 0x10000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_USDHC2_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc3: usdhc@30b60000 {
+ compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x30b60000 0x10000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_USDHC3_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ fec1: ethernet@30be0000 {
+ compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+ reg = <0x30be0000 0x10000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+ <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<3>;
+ fsl,num-rx-queues=<3>;
+ status = "disabled";
+ };
+ };
+ };
+};
#address-cells = <3>;
#size-cells = <2>;
reg = <0x21021000 0x2000>, <0x21020000 0x1000>, <0x02620128 4>;
- ranges = <0x81000000 0 0 0x23260000 0x4000 0x4000
- 0x82000000 0 0x60000000 0x60000000 0 0x10000000>;
+ ranges = <0x82000000 0 0x60000000 0x60000000
+ 0 0x10000000>;
status = "disabled";
device_type = "pci";
num-lanes = <2>;
+ bus-range = <0x00 0xff>;
+ /* error interrupt */
+ interrupts = <GIC_SPI 385 IRQ_TYPE_EDGE_RISING>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc1 0>, /* INT A */
};
+&k2g_pinctrl {
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ K2G_CORE_IOPAD(0x11cc) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ K2G_CORE_IOPAD(0x11d0) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+};
+
&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
status = "okay";
};
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/keystone.h>
#include "skeleton.dtsi"
/ {
ranges = <0x0 0x0 0x0 0xc0000000>;
dma-ranges = <0x80000000 0x8 0x00000000 0x80000000>;
+ k2g_pinctrl: pinmux@02621000 {
+ compatible = "pinctrl-single";
+ reg = <0x02621000 0x410>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x001b0007>;
+ };
+
uart0: serial@02530c00 {
compatible = "ns16550a";
current-speed = <115200>;
interrupts = <GIC_SPI 435 IRQ_TYPE_EDGE_RISING>;
};
+ k2l_pmx: pinmux@02620690 {
+ compatible = "pinctrl-single";
+ reg = <0x02620690 0xc>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,bit-per-mux;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x1>;
+ status = "disabled";
+
+ uart3_emifa_pins: pinmux_uart3_emifa_pins {
+ pinctrl-single,bits = <
+ /* UART3_EMIFA_SEL */
+ 0x0 0x0 0xc0
+ >;
+ };
+
+ uart2_emifa_pins: pinmux_uart2_emifa_pins {
+ pinctrl-single,bits = <
+ /* UART2_EMIFA_SEL */
+ 0x0 0x0 0x30
+ >;
+ };
+
+ uart01_spi2_pins: pinmux_uart01_spi2_pins {
+ pinctrl-single,bits = <
+ /* UART01_SPI2_SEL */
+ 0x0 0x0 0x4
+ >;
+ };
+
+ dfesync_rp1_pins: pinmux_dfesync_rp1_pins{
+ pinctrl-single,bits = <
+ /* DFESYNC_RP1_SEL */
+ 0x0 0x0 0x2
+ >;
+ };
+
+ avsif_pins: pinmux_avsif_pins {
+ pinctrl-single,bits = <
+ /* AVSIF_SEL */
+ 0x0 0x0 0x1
+ >;
+ };
+
+ gpio_emu_pins: pinmux_gpio_emu_pins {
+ pinctrl-single,bits = <
+ /*
+ * GPIO_EMU_SEL[31]: 0-GPIO31, 1-EMU33
+ * GPIO_EMU_SEL[30]: 0-GPIO30, 1-EMU32
+ * GPIO_EMU_SEL[29]: 0-GPIO29, 1-EMU31
+ * GPIO_EMU_SEL[28]: 0-GPIO28, 1-EMU30
+ * GPIO_EMU_SEL[27]: 0-GPIO27, 1-EMU29
+ * GPIO_EMU_SEL[26]: 0-GPIO26, 1-EMU28
+ * GPIO_EMU_SEL[25]: 0-GPIO25, 1-EMU27
+ * GPIO_EMU_SEL[24]: 0-GPIO24, 1-EMU26
+ * GPIO_EMU_SEL[23]: 0-GPIO23, 1-EMU25
+ * GPIO_EMU_SEL[22]: 0-GPIO22, 1-EMU24
+ * GPIO_EMU_SEL[21]: 0-GPIO21, 1-EMU23
+ * GPIO_EMU_SEL[20]: 0-GPIO20, 1-EMU22
+ * GPIO_EMU_SEL[19]: 0-GPIO19, 1-EMU21
+ * GPIO_EMU_SEL[18]: 0-GPIO18, 1-EMU20
+ * GPIO_EMU_SEL[17]: 0-GPIO17, 1-EMU19
+ */
+ 0x4 0x0000 0xFFFE0000
+ >;
+ };
+
+ gpio_timio_pins: pinmux_gpio_timio_pins {
+ pinctrl-single,bits = <
+ /*
+ * GPIO_TIMIO_SEL[15]: 0-GPIO15, 1-TIMO7
+ * GPIO_TIMIO_SEL[14]: 0-GPIO14, 1-TIMO6
+ * GPIO_TIMIO_SEL[13]: 0-GPIO13, 1-TIMO5
+ * GPIO_TIMIO_SEL[12]: 0-GPIO12, 1-TIMO4
+ * GPIO_TIMIO_SEL[11]: 0-GPIO11, 1-TIMO3
+ * GPIO_TIMIO_SEL[10]: 0-GPIO10, 1-TIMO2
+ * GPIO_TIMIO_SEL[9]: 0-GPIO9, 1-TIMI7
+ * GPIO_TIMIO_SEL[8]: 0-GPIO8, 1-TIMI6
+ * GPIO_TIMIO_SEL[7]: 0-GPIO7, 1-TIMI5
+ * GPIO_TIMIO_SEL[6]: 0-GPIO6, 1-TIMI4
+ * GPIO_TIMIO_SEL[5]: 0-GPIO5, 1-TIMI3
+ * GPIO_TIMIO_SEL[4]: 0-GPIO4, 1-TIMI2
+ */
+ 0x4 0x0 0xFFF0
+ >;
+ };
+
+ gpio_spi2cs_pins: pinmux_gpio_spi2cs_pins {
+ pinctrl-single,bits = <
+ /*
+ * GPIO_SPI2CS_SEL[3]: 0-GPIO3, 1-SPI2CS4
+ * GPIO_SPI2CS_SEL[2]: 0-GPIO2, 1-SPI2CS3
+ * GPIO_SPI2CS_SEL[1]: 0-GPIO1, 1-SPI2CS2
+ * GPIO_SPI2CS_SEL[0]: 0-GPIO0, 1-SPI2CS1
+ */
+ 0x4 0x0 0xF
+ >;
+ };
+
+ gpio_dfeio_pins: pinmux_gpio_dfeio_pins {
+ pinctrl-single,bits = <
+ /*
+ * GPIO_DFEIO_SEL[31]: 0-DFEIO17, 1-GPIO63
+ * GPIO_DFEIO_SEL[30]: 0-DFEIO16, 1-GPIO62
+ * GPIO_DFEIO_SEL[29]: 0-DFEIO15, 1-GPIO61
+ * GPIO_DFEIO_SEL[28]: 0-DFEIO14, 1-GPIO60
+ * GPIO_DFEIO_SEL[27]: 0-DFEIO13, 1-GPIO59
+ * GPIO_DFEIO_SEL[26]: 0-DFEIO12, 1-GPIO58
+ * GPIO_DFEIO_SEL[25]: 0-DFEIO11, 1-GPIO57
+ * GPIO_DFEIO_SEL[24]: 0-DFEIO10, 1-GPIO56
+ * GPIO_DFEIO_SEL[23]: 0-DFEIO9, 1-GPIO55
+ * GPIO_DFEIO_SEL[22]: 0-DFEIO8, 1-GPIO54
+ * GPIO_DFEIO_SEL[21]: 0-DFEIO7, 1-GPIO53
+ * GPIO_DFEIO_SEL[20]: 0-DFEIO6, 1-GPIO52
+ * GPIO_DFEIO_SEL[19]: 0-DFEIO5, 1-GPIO51
+ * GPIO_DFEIO_SEL[18]: 0-DFEIO4, 1-GPIO50
+ * GPIO_DFEIO_SEL[17]: 0-DFEIO3, 1-GPIO49
+ * GPIO_DFEIO_SEL[16]: 0-DFEIO2, 1-GPIO48
+ */
+ 0x8 0x0 0xFFFF0000
+ >;
+ };
+
+ gpio_emifa_pins: pinmux_gpio_emifa_pins {
+ pinctrl-single,bits = <
+ /*
+ * GPIO_EMIFA_SEL[15]: 0-EMIFA17, 1-GPIO47
+ * GPIO_EMIFA_SEL[14]: 0-EMIFA16, 1-GPIO46
+ * GPIO_EMIFA_SEL[13]: 0-EMIFA15, 1-GPIO45
+ * GPIO_EMIFA_SEL[12]: 0-EMIFA14, 1-GPIO44
+ * GPIO_EMIFA_SEL[11]: 0-EMIFA13, 1-GPIO43
+ * GPIO_EMIFA_SEL[10]: 0-EMIFA10, 1-GPIO42
+ * GPIO_EMIFA_SEL[9]: 0-EMIFA9, 1-GPIO41
+ * GPIO_EMIFA_SEL[8]: 0-EMIFA8, 1-GPIO40
+ * GPIO_EMIFA_SEL[7]: 0-EMIFA7, 1-GPIO39
+ * GPIO_EMIFA_SEL[6]: 0-EMIFA6, 1-GPIO38
+ * GPIO_EMIFA_SEL[5]: 0-EMIFA5, 1-GPIO37
+ * GPIO_EMIFA_SEL[4]: 0-EMIFA4, 1-GPIO36
+ * GPIO_EMIFA_SEL[3]: 0-EMIFA3, 1-GPIO35
+ * GPIO_EMIFA_SEL[2]: 0-EMIFA2, 1-GPIO34
+ * GPIO_EMIFA_SEL[1]: 0-EMIFA1, 1-GPIO33
+ * GPIO_EMIFA_SEL[0]: 0-EMIFA0, 1-GPIO32
+ */
+ 0x8 0x0 0xFFFF
+ >;
+ };
+ };
+
dspgpio0: keystone_dsp_gpio@02620240 {
compatible = "ti,keystone-dsp-gpio";
gpio-controller;
#address-cells = <3>;
#size-cells = <2>;
reg = <0x21801000 0x2000>, <0x21800000 0x1000>, <0x02620128 4>;
- ranges = <0x81000000 0 0 0x23250000 0 0x4000
- 0x82000000 0 0x50000000 0x50000000 0 0x10000000>;
+ ranges = <0x82000000 0 0x50000000 0x50000000
+ 0 0x10000000>;
status = "disabled";
device_type = "pci";
num-lanes = <2>;
+ bus-range = <0x00 0xff>;
+ /* error interrupt */
+ interrupts = <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc0 0>, /* INT A */
};
};
- pwm10: dmtimer-pwm@10 {
+ pwm10: dmtimer-pwm {
compatible = "ti,omap-dmtimer-pwm";
pinctrl-names = "default";
pinctrl-0 = <&pwm_pins>;
gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */
};
- lcd0: display@0 {
+ lcd0: display {
compatible = "panel-dpi";
label = "15";
status = "okay";
interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
dr_mode = "host";
snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
};
pcie@3400000 {
#include <dt-bindings/clock/meson8b-clkc.h>
#include <dt-bindings/gpio/meson8b-gpio.h>
+#include <dt-bindings/reset/amlogic,meson8b-reset.h>
#include "skeleton.dtsi"
/ {
#interrupt-cells = <3>;
};
+ reset: reset-controller@c1104404 {
+ compatible = "amlogic,meson8b-reset";
+ reg = <0xc1104404 0x20>;
+ #reset-cells = <1>;
+ };
+
wdt: watchdog@c1109900 {
compatible = "amlogic,meson8b-wdt";
reg = <0xc1109900 0x8>;
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <18432000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
};
clock-div = <1>;
};
- func_96m_ck: func_96m_ck {
+ func_96m_ck: func_96m_ck@540 {
#clock-cells = <0>;
};
vcc-supply = <&hsusb2_power>;
};
- tfp410: encoder@0 {
+ tfp410: encoder0 {
compatible = "ti,tfp410";
powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@0 {
+ dvi0: connector0 {
compatible = "dvi-connector";
label = "dvi";
};
};
- tv0: connector@1 {
+ tv0: connector1 {
compatible = "svideo-connector";
label = "tv";
};
- tfp410: encoder@0 {
+ tfp410: encoder0 {
compatible = "ti,tfp410";
powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* gpio_170 */
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@0 {
+ dvi0: connector0 {
compatible = "dvi-connector";
label = "dvi";
};
};
- tv0: connector@1 {
+ tv0: connector1 {
compatible = "svideo-connector";
label = "tv";
regulator-max-microvolt = <3300000>;
};
- tv0: connector@1 {
+ tv0: connector {
compatible = "svideo-connector";
label = "tv";
};
};
- tfp410: encoder@0 {
+ tfp410: encoder0 {
compatible = "ti,tfp410";
powerdown-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_dvi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@0 {
+ dvi0: connector0 {
compatible = "dvi-connector";
label = "dvi";
};
};
- tv0: connector@1 {
+ tv0: connector1 {
compatible = "svideo-connector";
label = "tv";
vdda_dac-supply = <&vdac>;
port {
- dpi_dvi_out: endpoint@0 {
+ dpi_dvi_out: endpoint {
remote-endpoint = <&tfp410_in>;
data-lines = <24>;
};
display2 = &tv0;
};
- lcd0: display@0 {
+ lcd0: display {
compatible = "panel-dpi";
label = "lcd";
&dss {
port {
- dpi_lcd_out: endpoint@1 {
+ dpi_lcd_out: endpoint {
remote-endpoint = <&lcd_in>;
data-lines = <24>;
};
model = "TimLL OMAP3 Devkit8000 with 4.3'' LCD panel";
compatible = "timll,omap3-devkit8000", "ti,omap3";
- lcd0: display@0 {
+ lcd0: display {
panel-timing {
clock-frequency = <10164705>;
hactive = <480>;
model = "TimLL OMAP3 Devkit8000 with 7.0'' LCD panel";
compatible = "timll,omap3-devkit8000", "ti,omap3";
- lcd0: display@0 {
+ lcd0: display {
panel-timing {
clock-frequency = <40000000>;
hactive = <800>;
};
};
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm11 0 2000000 0>;
+ pwm-names = "backlight";
+ brightness-levels = <0 11 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <9>; /* => 90 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&backlight_pins>;
+ };
+
+ pwm11: dmtimer-pwm {
+ compatible = "ti,omap-dmtimer-pwm";
+ ti,timers = <&timer11>;
+ #pwm-cells = <3>;
+ };
+
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
};
- tv0: connector@1 {
+ tv0: connector {
compatible = "svideo-connector";
label = "tv";
port@0 {
reg = <0>;
- opa_in: endpoint@0 {
+ opa_in: endpoint {
remote-endpoint = <&venc_out>;
};
};
port@1 {
reg = <1>;
- opa_out: endpoint@0 {
+ opa_out: endpoint {
remote-endpoint = <&tv_connector_in>;
};
};
};
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&tca6507 0 GPIO_ACTIVE_LOW>; /* W2CBW003 reset through tca6507 */
+ };
};
&omap3_pmx_core {
>;
};
+ backlight_pins: backlight_pins_pimnux {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20ba, MUX_MODE3) /* gpt11/gpio57 */
+ >;
+ };
+
dss_dpi_pins: pinmux_dss_dpi_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda.hdq */
>;
};
+
+ bma180_pins: pinmux_bma180_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x213a, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio115 */
+ >;
+ };
+
+ itg3200_pins: pinmux_itg3200_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20b8, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio56 */
+ >;
+ };
+
+ hmc5843_pins: pinmux_hmc5843_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2134, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio112 */
+ >;
+ };
};
&omap3_pmx_core2 {
bma180@41 {
compatible = "bosch,bma180";
reg = <0x41>;
+ pinctrl-names = "default";
+ pintcrl-0 = <&bma180_pins>;
interrupt-parent = <&gpio4>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
};
itg3200@68 {
compatible = "invensense,itg3200";
reg = <0x68>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&itg3200_pins>;
interrupt-parent = <&gpio2>;
- interrupts = <24 0>; /* GPIO_56 */
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>; /* GPIO_56 */
};
- /* leds */
- tca6507@45 {
+ /* leds + gpios */
+ tca6507: tca6507@45 {
compatible = "ti,tca6507";
#address-cells = <1>;
#size-cells = <0>;
hmc5843@1e {
compatible = "honeywell,hmc5883l";
reg = <0x1e>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hmc5843_pins>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>; /* gpio112 */
};
/* touchscreen */
gpios = <&gpio6 0 GPIO_ACTIVE_LOW>;
ti,x-plate-ohms = <600>;
};
+
+ /* RFID EEPROM */
+ m24lr64@50 {
+ compatible = "at,24c64";
+ reg = <0x50>;
+ };
};
&i2c3 {
bus-width = <4>;
ti,non-removable;
cap-power-off-card;
+ mmc-pwrseq = <&wifi_pwrseq>;
};
&mmc3 {
display0 = &lcd0;
};
- lcd0: display@0 {
+ lcd0: display {
compatible = "panel-dpi";
label = "lcd";
vcc-supply = <&hsusb1_power>;
};
- tfp410: encoder@0 {
+ tfp410: encoder {
compatible = "ti,tfp410";
powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* gpio_170 */
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@0 {
+ dvi0: connector {
compatible = "dvi-connector";
label = "dvi";
io-channels = <&twl_madc 0>, <&twl_madc 4>, <&twl_madc 12>;
io-channel-names = "temp", "bsi", "vbat";
};
+
+ pwm9: dmtimer-pwm {
+ compatible = "ti,omap-dmtimer-pwm";
+ #pwm-cells = <3>;
+ ti,timers = <&timer9>;
+ ti,clock-source = <0x00>; /* timer_sys_ck */
+ };
+
+ ir: n900-ir {
+ compatible = "nokia,n900-ir";
+ pwms = <&pwm9 0 26316 0>; /* 38000 Hz */
+ };
};
&omap3_pmx_core {
display0 = &dvi0;
};
- tfp410: encoder@0 {
+ tfp410: encoder {
compatible = "ti,tfp410";
ports {
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@0 {
+ dvi0: connector {
compatible = "dvi-connector";
label = "dvi";
pinctrl-names = "default";
pinctrl-0 = <&mcspi1_pins>;
- lcd0: display@0 {
+ lcd0: display {
compatible = "lgphilips,lb035q02";
label = "lcd35";
display0 = &lcd0;
};
- lcd0: display@0 {
+ lcd0: display {
compatible = "samsung,lte430wq-f0c", "panel-dpi";
label = "lcd43";
display0 = &lcd;
};
- tv: connector@1 {
+ tv: connector {
compatible = "connector-analog-tv";
label = "tv";
*/
/ {
- tfp410: encoder@0 {
+ tfp410: encoder {
compatible = "ti,tfp410";
powerdown-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* gpio_54 */
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@0 {
+ dvi0: connector {
compatible = "dvi-connector";
label = "dvi";
display0 = &lcd0;
};
- lcd0: display@0 {
+ lcd0: display {
compatible = "samsung,lte430wq-f0c", "panel-dpi";
label = "lcd";
dmas = <&sdma 31>,
<&sdma 32>;
dma-names = "tx", "rx";
+ clocks = <&mcbsp1_fck>;
+ clock-names = "fck";
status = "disabled";
};
dmas = <&sdma 33>,
<&sdma 34>;
dma-names = "tx", "rx";
+ clocks = <&mcbsp2_fck>, <&mcbsp2_ick>;
+ clock-names = "fck", "ick";
status = "disabled";
};
dmas = <&sdma 17>,
<&sdma 18>;
dma-names = "tx", "rx";
+ clocks = <&mcbsp3_fck>, <&mcbsp3_ick>;
+ clock-names = "fck", "ick";
status = "disabled";
};
dmas = <&sdma 19>,
<&sdma 20>;
dma-names = "tx", "rx";
+ clocks = <&mcbsp4_fck>;
+ clock-names = "fck";
status = "disabled";
};
dmas = <&sdma 21>,
<&sdma 22>;
dma-names = "tx", "rx";
+ clocks = <&mcbsp5_fck>;
+ clock-names = "fck";
status = "disabled";
};
};
};
- hdmi0: connector@0 {
+ hdmi0: connector {
compatible = "hdmi-connector";
label = "hdmi";
twl6040: twl@4b {
compatible = "ti,twl6040";
+ #clock-cells = <0>;
reg = <0x4b>;
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
ti,audpwron-gpio = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* gpio_160 */
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
+
+ clocks = <&twl6040>;
+ clock-names = "pdmclk";
+
status = "okay";
};
enable-active-high;
};
- tfp410: encoder@0 {
+ tfp410: encoder0 {
compatible = "ti,tfp410";
powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@0 {
+ dvi0: connector0 {
compatible = "dvi-connector";
label = "dvi";
};
};
- tpd12s015: encoder@1 {
+ tpd12s015: encoder1 {
compatible = "ti,tpd12s015";
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
port@0 {
reg = <0>;
- tpd12s015_in: endpoint@0 {
+ tpd12s015_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
- tpd12s015_out: endpoint@0 {
+ tpd12s015_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
- hdmi0: connector@1 {
+ hdmi0: connector1 {
compatible = "hdmi-connector";
label = "hdmi";
twl6040: twl@4b {
compatible = "ti,twl6040";
+ #clock-cells = <0>;
reg = <0x4b>;
pinctrl-names = "default";
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
+
+ clocks = <&twl6040>;
+ clock-names = "pdmclk";
+
status = "okay";
};
enable-active-high;
};
- tpd12s015: encoder@0 {
+ tpd12s015: encoder {
compatible = "ti,tpd12s015";
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
port@0 {
reg = <0>;
- tpd12s015_in: endpoint@0 {
+ tpd12s015_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
- tpd12s015_out: endpoint@0 {
+ tpd12s015_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
- hdmi0: connector@0 {
+ hdmi0: connector {
compatible = "hdmi-connector";
label = "hdmi";
twl6040: twl@4b {
compatible = "ti,twl6040";
+ #clock-cells = <0>;
reg = <0x4b>;
pinctrl-names = "default";
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
+
+ clocks = <&twl6040>;
+ clock-names = "pdmclk";
+
status = "okay";
};
};
};
- hdmi0: connector@0 {
+ hdmi0: connector {
compatible = "hdmi-connector";
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd_pins>;
twl6040: twl@4b {
compatible = "ti,twl6040";
+ #clock-cells = <0>;
reg = <0x4b>;
pinctrl-names = "default";
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
+
+ clocks = <&twl6040>;
+ clock-names = "pdmclk";
+
status = "okay";
};
};
};
- tpd12s015: encoder@0 {
+ tpd12s015: encoder {
compatible = "ti,tpd12s015";
pinctrl-names = "default";
port@0 {
reg = <0>;
- tpd12s015_in: endpoint@0 {
+ tpd12s015_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
- tpd12s015_out: endpoint@0 {
+ tpd12s015_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
- hdmi0: connector@0 {
+ hdmi0: connector {
compatible = "hdmi-connector";
label = "hdmi";
twl6040: twl@4b {
compatible = "ti,twl6040";
+ #clock-cells = <0>;
reg = <0x4b>;
pinctrl-names = "default";
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
+
+ clocks = <&twl6040>;
+ clock-names = "pdmclk";
+
status = "okay";
};
};
};
- hdmi0: connector@0 {
+ hdmi0: connector0 {
compatible = "hdmi-connector";
label = "hdmi";
};
};
- tfp410: encoder@0 {
+ tfp410: encoder0 {
compatible = "ti,tfp410";
ports {
port@0 {
reg = <0>;
- tfp410_in: endpoint@0 {
+ tfp410_in: endpoint {
remote-endpoint = <&dpi_dvi_out>;
};
};
port@1 {
reg = <1>;
- tfp410_out: endpoint@0 {
+ tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
- dvi0: connector@1 {
+ dvi0: connector1 {
compatible = "dvi-connector";
label = "dvi";
pinctrl-0 = <&dss_dpi_pins>;
port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
dpi_dvi_out: endpoint@0 {
+ reg = <0>;
remote-endpoint = <&tfp410_in>;
data-lines = <24>;
};
dpi_lcd_out: endpoint@1 {
+ reg = <1>;
remote-endpoint = <&lcd_in>;
data-lines = <24>;
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
marvell,intc-nr-irqs = <34>;
};
+ pinctrl: pinctrl@40e00000 {
+ reg = <0x40e00054 0x20 0x40e0000c 0xc 0x40e0010c 4
+ 0x40f00020 0x10>;
+ compatible = "marvell,pxa27x-pinctrl";
+ };
+
gpio: gpio@40e00000 {
compatible = "intel,pxa27x-gpio";
+ gpio-ranges = <&pinctrl 0 0 128>;
clocks = <&clks CLK_NONE>;
};
reg = <0x40900000 0x3c>;
interrupts = <30 31>;
};
+
+ lcd-controller@40500000 {
+ compatible = "marvell,pxa2xx-lcdc";
+ reg = <0x44000000 0x10000>;
+ interrupts = <17>;
+ clocks = <&clks CLK_LCD>;
+ status = "disabled";
+ };
};
};
/* The pxa3xx skeleton simply augments the 2xx version */
#include "pxa2xx.dtsi"
+#define MFP_PIN_PXA300(gpio) \
+ ((gpio <= 2) ? (0x00b4 + 4 * gpio) : \
+ (gpio <= 26) ? (0x027c + 4 * (gpio - 3)) : \
+ (gpio <= 98) ? (0x0400 + 4 * (gpio - 27)) : \
+ (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \
+ 0)
+
+#define MFP_PIN_PXA310(gpio) \
+ ((gpio <= 2) ? (0x00b4 + 4 * gpio) : \
+ (gpio <= 26) ? (0x027c + 4 * (gpio - 3)) : \
+ (gpio <= 29) ? (0x0400 + 4 * (gpio - 27)) : \
+ (gpio <= 98) ? (0x0418 + 4 * (gpio - 30)) : \
+ (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \
+ (gpio <= 262) ? 0 : \
+ (gpio <= 268) ? (0x052c + 4 * (gpio - 263)) : \
+ 0)
+
+#define MFP_PIN_PXA320(gpio) \
+ ((gpio <= 4) ? (0x0124 + 4 * gpio) : \
+ (gpio <= 9) ? (0x028c + 4 * (gpio - 5)) : \
+ (gpio <= 10) ? (0x0458 + 4 * (gpio - 10)) : \
+ (gpio <= 26) ? (0x02a0 + 4 * (gpio - 11)) : \
+ (gpio <= 48) ? (0x0400 + 4 * (gpio - 27)) : \
+ (gpio <= 62) ? (0x045c + 4 * (gpio - 49)) : \
+ (gpio <= 73) ? (0x04b4 + 4 * (gpio - 63)) : \
+ (gpio <= 98) ? (0x04f0 + 4 * (gpio - 74)) : \
+ (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \
+ 0)
+
+/*
+ * MFP Alternate functions for pins having a gpio.
+ * Example of use: pinctrl-single,pins = < MFP_PIN_PXA310(21) MFP_AF1 >
+ */
+#define MFP_AF0 (0 << 0)
+#define MFP_AF1 (1 << 0)
+#define MFP_AF2 (2 << 0)
+#define MFP_AF3 (3 << 0)
+#define MFP_AF4 (4 << 0)
+#define MFP_AF5 (5 << 0)
+#define MFP_AF6 (6 << 0)
+
+/*
+ * MFP drive strength functions for pins.
+ * Example of use: pinctrl-single,drive-strength = MFP_DS03X;
+ */
+#define MFP_DSMSK (0x7 << 10)
+#define MFP_DS01X < (0x0 << 10) MFP_DSMSK >
+#define MFP_DS02X < (0x1 << 10) MFP_DSMSK >
+#define MFP_DS03X < (0x2 << 10) MFP_DSMSK >
+#define MFP_DS04X < (0x3 << 10) MFP_DSMSK >
+#define MFP_DS06X < (0x4 << 10) MFP_DSMSK >
+#define MFP_DS08X < (0x5 << 10) MFP_DSMSK >
+#define MFP_DS10X < (0x6 << 10) MFP_DSMSK >
+#define MFP_DS13X < (0x7 << 10) MFP_DSMSK >
+
+/*
+ * MFP low power mode for pins.
+ * Example of use:
+ * pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW|MFP_LPM_EDGE_FALL);
+ *
+ * Table that determines the low power modes outputs, with actual settings
+ * used in parentheses for don't-care values. Except for the float output,
+ * the configured driven and pulled levels match, so if there is a need for
+ * non-LPM pulled output, the same configuration could probably be used.
+ *
+ * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
+ * (bit 7) (bit 8) (bit 14) (bit 13) (bit 15)
+ *
+ * Input 0 X(0) X(0) X(0) 0
+ * Drive 0 0 0 0 X(1) 0
+ * Drive 1 0 1 X(1) 0 0
+ * Pull hi (1) 1 X(1) 1 0 0
+ * Pull lo (0) 1 X(0) 0 1 0
+ * Z (float) 1 X(0) 0 0 0
+ */
+#define MFP_LPM(x) < (x) MFP_LPM_MSK >
+
+#define MFP_LPM_MSK 0xe1f0
+#define MFP_LPM_INPUT 0x0000
+#define MFP_LPM_DRIVE_LOW 0x2000
+#define MFP_LPM_DRIVE_HIGH 0x4100
+#define MFP_LPM_PULL_LOW 0x2080
+#define MFP_LPM_PULL_HIGH 0x4180
+#define MFP_LPM_FLOAT 0x0080
+
+#define MFP_LPM_EDGE_NONE 0x0000
+#define MFP_LPM_EDGE_RISE 0x0010
+#define MFP_LPM_EDGE_FALL 0x0020
+#define MFP_LPM_EDGE_BOTH 0x0030
+
/ {
model = "Marvell PXA3xx familiy SoC";
compatible = "marvell,pxa3xx";
marvell,intc-nr-irqs = <56>;
};
+ pinctrl: pinctrl@40e10000 {
+ compatible = "pinconf-single";
+ reg = <0x40e10000 0xffff>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x7>;
+ };
+
gpio: gpio@40e00000 {
compatible = "intel,pxa3xx-gpio";
reg = <0x40e00000 0x10000>;
compatible = "marvell,pxa-ohci";
reg = <0x4c000000 0x10000>;
interrupts = <3>;
- clocks = <&clks CLK_USBHOST>;
+ clocks = <&clks CLK_USBH>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@40b00000 {
+ compatible = "marvell,pxa270-pwm";
+ reg = <0x40b00000 0x10>;
+ #pwm-cells = <1>;
+ clocks = <&clks CLK_PWM0>;
+ status = "disabled";
+ };
+
+ pwm1: pwm@40b00010 {
+ compatible = "marvell,pxa270-pwm";
+ reg = <0x40b00010 0x10>;
+ #pwm-cells = <1>;
+ clocks = <&clks CLK_PWM1>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@40c00000 {
+ compatible = "marvell,pxa270-pwm";
+ reg = <0x40c00000 0x10>;
+ #pwm-cells = <1>;
+ clocks = <&clks CLK_PWM0>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@40c00010 {
+ compatible = "marvell,pxa270-pwm";
+ reg = <0x40c00010 0x10>;
+ #pwm-cells = <1>;
+ clocks = <&clks CLK_PWM1>;
status = "disabled";
};
};
--- /dev/null
+/*
+ * Copyright 2016 Linaro Ltd
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "qcom-msm8660.dtsi"
+
+/ {
+ model = "Qualcomm APQ8060 Dragonboard";
+ compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+ aliases {
+ serial0 = &gsbi12_serial;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ /* Main power of the board: 3.7V */
+ vph: regulator-fixed {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-name = "VPH";
+ regulator-type = "voltage";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* This is a levelshifter for SDCC5 */
+ dragon_vio_txb: txb0104rgyr {
+ compatible = "regulator-fixed";
+ regulator-name = "Dragon SDCC levelshifter";
+ vin-supply = <&pm8058_l14>;
+ regulator-always-on;
+ };
+ };
+
+ soc {
+ pinctrl@800000 {
+ /* eMMMC pins, all 8 data lines connected */
+ dragon_sdcc1_pins: sdcc1 {
+ mux {
+ pins = "gpio159", "gpio160", "gpio161",
+ "gpio162", "gpio163", "gpio164",
+ "gpio165", "gpio166", "gpio167",
+ "gpio168";
+ function = "sdc1";
+ };
+ clk {
+ pins = "gpio167"; /* SDC5 CLK */
+ drive-strength = <16>;
+ bias-disable;
+ };
+ cmd {
+ pins = "gpio168"; /* SDC5 CMD */
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ data {
+ /* SDC5 D0 to D7 */
+ pins = "gpio159", "gpio160", "gpio161", "gpio162",
+ "gpio163", "gpio164", "gpio165", "gpio166";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ /*
+ * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+ * configuration.
+ */
+ dragon_sdcc3_pins: sdcc3 {
+ clk {
+ pins = "sdc3_clk";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ cmd {
+ pins = "sdc3_cmd";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ data {
+ pins = "sdc3_data";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ /* Second SD card slot pins */
+ dragon_sdcc5_pins: sdcc5 {
+ mux {
+ pins = "gpio95", "gpio96", "gpio97",
+ "gpio98", "gpio99", "gpio100";
+ function = "sdc5";
+ };
+ clk {
+ pins = "gpio97"; /* SDC5 CLK */
+ drive-strength = <16>;
+ bias-disable;
+ };
+ cmd {
+ pins = "gpio95"; /* SDC5 CMD */
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ data {
+ /* SDC5 D0 to D3 */
+ pins = "gpio96", "gpio98", "gpio99", "gpio100";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ dragon_gsbi12_i2c_pins: gsbi12_i2c {
+ mux {
+ pins = "gpio115", "gpio116";
+ function = "gsbi12";
+ };
+ pinconf {
+ pins = "gpio115", "gpio116";
+ drive-strength = <16>;
+ /* These have external pull-up 4.7kOhm to 1.8V */
+ bias-disable;
+ };
+ };
+
+ /* Primary serial port uart 0 pins */
+ dragon_gsbi12_serial_pins: gsbi12_serial {
+ mux {
+ pins = "gpio117", "gpio118";
+ function = "gsbi12";
+ };
+ tx {
+ pins = "gpio117";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ rx {
+ pins = "gpio118";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+ };
+
+ qcom,ssbi@500000 {
+ pmic@0 {
+ keypad@148 {
+ linux,keymap = <
+ MATRIX_KEY(0, 0, KEY_MENU)
+ MATRIX_KEY(0, 2, KEY_1)
+ MATRIX_KEY(0, 3, KEY_4)
+ MATRIX_KEY(0, 4, KEY_7)
+ MATRIX_KEY(1, 0, KEY_UP)
+ MATRIX_KEY(1, 1, KEY_LEFT)
+ MATRIX_KEY(1, 2, KEY_DOWN)
+ MATRIX_KEY(1, 3, KEY_5)
+ MATRIX_KEY(1, 3, KEY_8)
+ MATRIX_KEY(2, 0, KEY_HOME)
+ MATRIX_KEY(2, 1, KEY_REPLY)
+ MATRIX_KEY(2, 2, KEY_2)
+ MATRIX_KEY(2, 3, KEY_6)
+ MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+ MATRIX_KEY(3, 1, KEY_RIGHT)
+ MATRIX_KEY(3, 2, KEY_3)
+ MATRIX_KEY(3, 3, KEY_9)
+ MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+ MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+ MATRIX_KEY(4, 1, KEY_BACK)
+ MATRIX_KEY(4, 2, KEY_CAMERA)
+ MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+ >;
+ keypad,num-rows = <6>;
+ keypad,num-columns = <5>;
+ };
+
+ gpio@150 {
+ dragon_bmp085_gpios: bmp085-gpios {
+ pinconf {
+ pins = "gpio16";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_sdcc3_gpios: sdcc3-gpios {
+ pinconf {
+ pins = "gpio22";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_sdcc5_gpios: sdcc5-gpios {
+ pinconf {
+ pins = "gpio26";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_ak8975_gpios: ak8975-gpios {
+ pinconf {
+ pins = "gpio33";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ };
+ };
+ };
+
+ gsbi@19c00000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+
+ serial@19c40000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+ };
+
+ i2c@19c80000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+
+ ak8975@0c {
+ compatible = "asahi-kasei,ak8975";
+ reg = <0x0c>;
+ /* GPIO33 has interrupt 224 on the PM8058 */
+ interrupt-parent = <&pm8058_gpio>;
+ interrupts = <224 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_ak8975_gpios>;
+ vid-supply = <&pm8058_lvs0>; // 1.8V
+ vdd-supply = <&pm8058_l14>; // 2.85V
+ };
+ bmp085@77 {
+ compatible = "bosch,bmp085";
+ reg = <0x77>;
+ /* GPIO16 has interrupt 207 on the PM8058 */
+ interrupt-parent = <&pm8058_gpio>;
+ interrupts = <207 IRQ_TYPE_EDGE_RISING>;
+ reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_bmp085_gpios>;
+ vddd-supply = <&pm8058_lvs0>; // 1.8V
+ vdda-supply = <&pm8058_l14>; // 2.85V
+ };
+ };
+ };
+
+ rpm@104000 {
+ /*
+ * Set up of the PMIC RPM regulators for this board
+ * PM8901 supplies "preliminary regulators" whatever
+ * that means
+ */
+ pm8901-regulators {
+ vdd_l0-supply = <&pm8901_s4>;
+ vdd_l1-supply = <&vph>;
+ vdd_l2-supply = <&vph>;
+ vdd_l3-supply = <&vph>;
+ vdd_l4-supply = <&vph>;
+ vdd_l5-supply = <&vph>;
+ vdd_l6-supply = <&vph>;
+ /* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ lvs0_in-supply = <&pm8058_s3>;
+ lvs1_in-supply = <&pm8901_s4>;
+ lvs2_in-supply = <&pm8058_l0>;
+ lvs3_in-supply = <&pm8058_s2>;
+ mvs_in-supply = <&pm8058_s3>;
+
+ l0 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l2 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l4 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l5 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l6 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ bias-pull-down;
+ };
+
+ /* s0 and s1 are SAW regulators controlled over SPM */
+ s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ /* LVS0 thru 3 and mvs0 are just switches */
+ lvs0 {
+ regulator-always-on;
+ };
+ lvs1 { };
+ lvs2 { };
+ lvs3 { };
+ mvs0 {};
+
+ };
+
+ pm8058-regulators {
+ vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+ vdd_l2_l11_l12-supply = <&vph>;
+ vdd_l3_l4_l5-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l8-supply = <&vph>;
+ vdd_l9-supply = <&vph>;
+ vdd_l10-supply = <&vph>;
+ vdd_l13_l16-supply = <&pm8058_s4>;
+ vdd_l14_l15-supply = <&vph>;
+ vdd_l17_l18-supply = <&vph>;
+ vdd_l19_l20-supply = <&vph>;
+ vdd_l21-supply = <&pm8058_s3>;
+ vdd_l22-supply = <&pm8058_s3>;
+ vdd_l23_l24_l25-supply = <&pm8058_s3>;
+ vdd_s0-supply = <&vph>;
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_ncp-supply = <&vph>;
+
+ l0 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l4 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l5 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l6 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3600000>;
+ bias-pull-down;
+ };
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l8 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <3050000>;
+ bias-pull-down;
+ };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l10 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l11 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ bias-pull-down;
+ };
+ l12 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ bias-pull-down;
+ };
+ l13 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ bias-pull-down;
+ };
+ l14 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+ l15 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+ l17 {
+ // 1.5V according to schematic
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l18 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ bias-pull-down;
+ };
+ l19 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ bias-pull-down;
+ };
+ l20 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l21 {
+ // 1.1 V according to schematic
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+ l22 {
+ // 1.2 V according to schematic
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ bias-pull-down;
+ };
+ l23 {
+ // Unused
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l24 {
+ // Unused
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l25 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ s0 {
+ // regulator-min-microvolt = <500000>;
+ // regulator-max-microvolt = <1325000>;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s1 {
+ // regulator-min-microvolt = <500000>;
+ // regulator-max-microvolt = <1250000>;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s2 {
+ // 1.3 V according to schematic
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ regulator-always-on;
+ bias-pull-down;
+ };
+ s4 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ qcom,switch-mode-frequency = <1600000>;
+ regulator-always-on;
+ bias-pull-down;
+ };
+
+ /* LVS0 and LVS1 are just switches */
+ lvs0 {
+ bias-pull-down;
+ };
+ lvs1 {
+ bias-pull-down;
+ };
+
+ ncp {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ };
+ };
+ };
+ amba {
+ /* Internal 3.69 GiB eMMC */
+ sdcc@12400000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc1_pins>;
+ vmmc-supply = <&pm8901_l5>;
+ vqmmc-supply = <&pm8901_lvs0>;
+ };
+
+ /* External micro SD card, directly connected, pulled up to 2.85 V */
+ sdcc@12180000 {
+ status = "okay";
+ /* Enable SSBI GPIO 22 as input, use for card detect */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+ cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&pm8058_l14>;
+ };
+
+ /*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+ sdcc@12200000 {
+ status = "okay";
+ /* Enable SSBI GPIO 26 as input, use for card detect */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+ cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&pm8058_l14>;
+ vqmmc-supply = <&dragon_vio_txb>;
+ };
+ };
+ };
+};
+++ /dev/null
-&tlmm_pinmux {
- card_detect: card-detect {
- mux {
- pins = "gpio26";
- function = "gpio";
- bias-disable;
- };
- };
-
- pcie_pins: pcie-pinmux {
- mux {
- pins = "gpio27";
- function = "gpio";
- };
- conf {
- pins = "gpio27";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- user_leds: user-leds {
- mux {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- };
-
- conf {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- output-low;
- };
- };
-
- magneto_pins: magneto-pins {
- mux {
- pins = "gpio31", "gpio48";
- function = "gpio";
- bias-disable;
- };
- };
-};
-
-&pm8921_mpps {
- mpp_leds: mpp-leds {
- pinconf {
- pins = "mpp7", "mpp8";
- function = "digital";
- output-low;
- };
- };
-};
+++ /dev/null
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-db600c-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Arrow Electronics, APQ8064 DB600c";
- compatible = "arrow,db600c", "qcom,apq8064";
-
- aliases {
- serial0 = &gsbi7_serial;
- serial1 = &gsbi1_serial;
- i2c0 = &gsbi2_i2c;
- i2c1 = &gsbi3_i2c;
- i2c2 = &gsbi4_i2c;
- i2c3 = &gsbi7_i2c;
- spi0 = &gsbi5_spi;
- };
-
- regulators {
- compatible = "simple-bus";
- vph: regulator-fixed@1 {
- compatible = "regulator-fixed";
- regulator-min-microvolt = <4500000>;
- regulator-max-microvolt = <4500000>;
- regulator-name = "VPH";
- regulator-type = "voltage";
- regulator-boot-on;
- };
-
- /* on board fixed 3.3v supply */
- vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- };
-
- soc {
- rpm@108000 {
- regulators {
- vdd_s1-supply = <&vph>;
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- vdd_s5-supply = <&vph>;
- vdd_s6-supply = <&vph>;
- vdd_s7-supply = <&vph>;
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
- vdd_l3_l15_l17-supply = <&vph>;
- vdd_l4_l14-supply = <&vph>;
- vdd_l5_l8_l16-supply = <&vph>;
- vdd_l6_l7-supply = <&vph>;
- vdd_l9_l11-supply = <&vph>;
- vdd_l10_l22-supply = <&vph>;
- vdd_l21_l23_l29-supply = <&vph>;
- vdd_l24-supply = <&pm8921_s1>;
- vdd_l25-supply = <&pm8921_s1>;
- vdd_l26-supply = <&pm8921_s7>;
- vdd_l27-supply = <&pm8921_s7>;
- vdd_l28-supply = <&pm8921_s7>;
- vin_lvs1_3_6-supply = <&pm8921_s4>;
- vin_lvs2-supply = <&pm8921_s1>;
- vin_lvs4_5_7-supply = <&pm8921_s4>;
-
- s1 {
- regulator-always-on;
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- };
-
- s3 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- qcom,switch-mode-frequency = <4800000>;
- };
-
- s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s7 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <3200000>;
- };
-
- l3 {
- regulator-min-microvolt = <3050000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
-
- l4 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
-
- l5 {
- regulator-min-microvolt = <2750000>;
- regulator-max-microvolt = <3000000>;
- bias-pull-down;
- regulator-boot-on;
- regulator-always-on;
- };
-
- l6 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- bias-pull-down;
- };
-
- l23 {
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- bias-pull-down;
- };
-
- lvs6 {
- bias-pull-down;
- };
-
- lvs7 {
- bias-pull-down;
- };
- };
- };
-
- gsbi@12440000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_UART_W_FC>;
- serial@12450000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi1_uart_4pins>;
- };
- };
-
- gsbi@12480000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@124a0000 {
- /* On Low speed expansion and Sensors */
- label = "LS-I2C0";
- status = "okay";
- lis3mdl_mag@1e {
- compatible = "st,lis3mdl-magn";
- reg = <0x1e>;
- vdd-supply = <&vcc3v3>;
- vddio-supply = <&pm8921_s4>;
- pinctrl-names = "default";
- pinctrl-0 = <&magneto_pins>;
- interrupt-parent = <&tlmm_pinmux>;
-
- st,drdy-int-pin = <2>;
- interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
- <31 IRQ_TYPE_EDGE_RISING>; /* INT */
- };
- };
- };
-
- gsbi@16200000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16280000 {
- /* On Low speed expansion */
- status = "okay";
- label = "LS-I2C1";
- clock-frequency = <200000>;
- eeprom@52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <64>;
- };
- };
- };
-
- gsbi@16300000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16380000 {
- /* On High speed expansion */
- label = "HS-CAM-I2C3";
- status = "okay";
- };
- };
-
- gsbi@1a200000 {
- status = "okay";
- spi@1a280000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
- };
- };
-
- /* DEBUG UART */
- gsbi@16600000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
- serial@16640000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi7_uart_2pins>;
- };
-
- i2c@16680000 {
- /* On High speed expansion */
- status = "okay";
- label = "HS-CAM-I2C2";
- };
- };
-
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
- compatible = "gpio-leds";
-
- user-led0 {
- label = "user0-led";
- gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- user-led1 {
- label = "user1-led";
- gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- user-led2 {
- label = "user2-led";
- gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- user-led3 {
- label = "user3-led";
- gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- };
-
- wifi-led {
- label = "WiFi-led";
- gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- bt-led {
- label = "BT-led";
- gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- pci@1b500000 {
- status = "okay";
- vdda-supply = <&pm8921_s3>;
- vdda_phy-supply = <&pm8921_lvs6>;
- vdda_refclk-supply = <&vcc3v3>;
- pinctrl-0 = <&pcie_pins>;
- pinctrl-names = "default";
- perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- target-supply = <&pm8921_lvs7>;
- };
-
- /* OTG */
- phy@12500000 {
- status = "okay";
- dr_mode = "peripheral";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l4>;
- };
-
- phy@12520000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- phy@12530000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- gadget@12500000 {
- status = "okay";
- };
-
- /* OTG */
- usb@12500000 {
- status = "okay";
- };
-
- usb@12520000 {
- status = "okay";
- };
-
- usb@12530000 {
- status = "okay";
- };
-
- amba {
- /* eMMC */
- sdcc@12400000 {
- status = "okay";
- vmmc-supply = <&pm8921_l5>;
- vqmmc-supply = <&pm8921_s4>;
- };
-
- /* External micro SD card */
- sdcc@12180000 {
- status = "okay";
- vmmc-supply = <&pm8921_l6>;
- pinctrl-names = "default";
- pinctrl-0 = <&card_detect>;
- cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- };
- };
-};
--- /dev/null
+&tlmm_pinmux {
+ card_detect: card-detect {
+ mux {
+ pins = "gpio26";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ pcie_pins: pcie-pinmux {
+ mux {
+ pins = "gpio27";
+ function = "gpio";
+ };
+ conf {
+ pins = "gpio27";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ user_leds: user-leds {
+ mux {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ };
+
+ conf {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ output-low;
+ };
+ };
+
+ magneto_pins: magneto-pins {
+ mux {
+ pins = "gpio31", "gpio48";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+};
+
+&pm8921_mpps {
+ mpp_leds: mpp-leds {
+ pinconf {
+ pins = "mpp7", "mpp8";
+ function = "digital";
+ output-low;
+ };
+ };
+};
--- /dev/null
+#include "qcom-apq8064-v2.0.dtsi"
+#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+
+/ {
+ model = "Arrow Electronics, APQ8064 SD_600eval";
+ compatible = "arrow,sd_600eval", "qcom,apq8064";
+
+ aliases {
+ serial0 = &gsbi7_serial;
+ serial1 = &gsbi1_serial;
+ i2c0 = &gsbi2_i2c;
+ i2c1 = &gsbi3_i2c;
+ i2c2 = &gsbi4_i2c;
+ i2c3 = &gsbi7_i2c;
+ spi0 = &gsbi5_spi;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ vph: regulator-fixed@1 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <4500000>;
+ regulator-max-microvolt = <4500000>;
+ regulator-name = "VPH";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ };
+
+ /* on board fixed 3.3v supply */
+ vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ };
+
+ soc {
+ rpm@108000 {
+ regulators {
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_s5-supply = <&vph>;
+ vdd_s6-supply = <&vph>;
+ vdd_s7-supply = <&vph>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l3_l15_l17-supply = <&vph>;
+ vdd_l4_l14-supply = <&vph>;
+ vdd_l5_l8_l16-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l9_l11-supply = <&vph>;
+ vdd_l10_l22-supply = <&vph>;
+ vdd_l21_l23_l29-supply = <&vph>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l26-supply = <&pm8921_s7>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s1>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <4800000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+
+ s7 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <3050000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ l5 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ l23 {
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ lvs6 {
+ bias-pull-down;
+ };
+
+ lvs7 {
+ bias-pull-down;
+ };
+ };
+ };
+
+ gsbi@12440000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_UART_W_FC>;
+ serial@12450000 {
+ label = "LS-UART1";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi1_uart_4pins>;
+ };
+ };
+
+ gsbi@12480000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@124a0000 {
+ /* On Low speed expansion and Sensors */
+ label = "LS-I2C0";
+ status = "okay";
+ lis3mdl_mag@1e {
+ compatible = "st,lis3mdl-magn";
+ reg = <0x1e>;
+ vdd-supply = <&vcc3v3>;
+ vddio-supply = <&pm8921_s4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&magneto_pins>;
+ interrupt-parent = <&tlmm_pinmux>;
+
+ st,drdy-int-pin = <2>;
+ interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
+ <31 IRQ_TYPE_EDGE_RISING>; /* INT */
+ };
+ };
+ };
+
+ gsbi@16200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16280000 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C1";
+ clock-frequency = <200000>;
+ eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <64>;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16380000 {
+ /* On High speed expansion */
+ label = "HS-CAM-I2C3";
+ status = "okay";
+ };
+ };
+
+ gsbi@1a200000 {
+ status = "okay";
+ spi@1a280000 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+ };
+ };
+
+ /* DEBUG UART */
+ gsbi@16600000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial@16640000 {
+ label = "LS-UART0";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi7_uart_2pins>;
+ };
+
+ i2c@16680000 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-CAM-I2C2";
+ };
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+ compatible = "gpio-leds";
+
+ user-led0 {
+ label = "user0-led";
+ gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ user-led1 {
+ label = "user1-led";
+ gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ user-led2 {
+ label = "user2-led";
+ gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ user-led3 {
+ label = "user3-led";
+ gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ };
+
+ wifi-led {
+ label = "WiFi-led";
+ gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ bt-led {
+ label = "BT-led";
+ gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ pci@1b500000 {
+ status = "okay";
+ vdda-supply = <&pm8921_s3>;
+ vdda_phy-supply = <&pm8921_lvs6>;
+ vdda_refclk-supply = <&vcc3v3>;
+ pinctrl-0 = <&pcie_pins>;
+ pinctrl-names = "default";
+ perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+ };
+
+ phy@1b400000 {
+ status = "okay";
+ };
+
+ sata@29000000 {
+ status = "okay";
+ target-supply = <&pm8921_lvs7>;
+ };
+
+ /* OTG */
+ phy@12500000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+
+ phy@12520000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ phy@12530000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ gadget@12500000 {
+ status = "okay";
+ };
+
+ /* OTG */
+ usb@12500000 {
+ status = "okay";
+ };
+
+ usb@12520000 {
+ status = "okay";
+ };
+
+ usb@12530000 {
+ status = "okay";
+ };
+
+ amba {
+ /* eMMC */
+ sdcc@12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ vqmmc-supply = <&pm8921_s4>;
+ };
+
+ /* External micro SD card */
+ sdcc@12180000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&card_detect>;
+ cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
gpio-keys {
compatible = "gpio-keys";
- power {
- label = "Power";
- gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- gpio-key,wakeup;
- };
volume_up {
label = "Volume Up";
gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
};
};
+ sdcc1_pins: sdcc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strengh = <16>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "sdc1_cmd";
+ drive-strengh = <10>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "sdc1_data";
+ drive-strengh = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdcc3_pins: sdcc3-pin-active {
+ clk {
+ pins = "sdc3_clk";
+ drive-strengh = <8>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "sdc3_cmd";
+ drive-strengh = <8>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "sdc3_data";
+ drive-strengh = <8>;
+ bias-pull-up;
+ };
+ };
+
ps_hold: ps_hold {
mux {
pins = "gpio78";
};
};
- sdcc1_pin_a: sdcc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strengh = <16>;
- bias-disable;
- };
-
- cmd {
- pins = "sdc1_cmd";
- drive-strengh = <10>;
- bias-pull-up;
- };
-
- data {
- pins = "sdc1_data";
- drive-strengh = <10>;
- bias-pull-up;
- };
- };
-
- sdcc3_pin_a: sdcc3-pin-active {
- clk {
- pins = "sdc3_clk";
- drive-strengh = <8>;
- bias-disable;
- };
-
- cmd {
- pins = "sdc3_cmd";
- drive-strengh = <8>;
- bias-pull-up;
- };
-
- data {
- pins = "sdc3_data";
- drive-strengh = <8>;
- bias-pull-up;
- };
- };
sdcc3_cd_pin_a: sdcc3-cd-pin-active {
pins = "gpio26";
vmmc-supply = <&pm8921_l5>;
vqmmc-supply = <&pm8921_s4>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&sdcc1_pin_a>;
};
sdcc3: sdcc@12180000 {
cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
- pinctrl-0 = <&sdcc3_pin_a>, <&sdcc3_cd_pin_a>;
+ pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
};
};
};
apps_smsm: apps@0 {
reg = <0>;
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
modem_smsm: modem@1 {
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm-apq8064";
+ };
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
sdcc1: sdcc@12400000 {
status = "disabled";
compatible = "arm,pl18x", "arm,primecell";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdcc1_pins>;
arm,primecell-periphid = <0x00051180>;
reg = <0x12400000 0x2000>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
bus-width = <8>;
non-removable;
status = "ok";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
};
sdhci@f98a4900 {
cd-gpios = <&msmgpio 62 0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
bus-width = <4>;
+ status = "ok";
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
};
function = "blsp_spi8";
};
};
+
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
};
i2c@f9967000 {
};
};
};
+
+ smd {
+ rpm {
+ rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+ };
+
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vin_5vs-supply = <&pm8941_5v>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ };
};
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm";
+ clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ };
+ };
+
cpu-pmu {
compatible = "qcom,krait-pmu";
interrupts = <1 7 0xf04>;
};
};
+ pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
clocks {
sleep_clk: sleep_clk {
compatible = "fixed-clock";
};
};
+ /* Temporary fixed regulator */
+ vsdcc_fixed: vsdcc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "SDCC Power";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ regulator-always-on;
+ };
+
amba {
/* eMMC */
sdcc1: sdcc@12400000 {
status = "okay";
+ vmmc-supply = <&vsdcc_fixed>;
};
/* External micro SD card */
sdcc3: sdcc@12180000 {
status = "okay";
+ vmmc-supply = <&vsdcc_fixed>;
};
};
};
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x19c40000 0x1000>,
<0x19c00000 0x1000>;
- interrupts = <0 195 0x0>;
+ interrupts = <0 195 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
+
+ gsbi12_i2c: i2c@19c80000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x19c80000 0x1000>;
+ interrupts = <0 196 IRQ_TYPE_NONE>;
+ clocks = <&gcc GSBI12_QUP_CLK>, <&gcc GSBI12_H_CLK>;
+ clock-names = "core", "iface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};
qcom,ssbi@500000 {
#address-cells = <1>;
#size-cells = <0>;
+ pm8058_gpio: gpio@150 {
+ compatible = "qcom,pm8058-gpio",
+ "qcom,ssbi-gpio";
+ reg = <0x150>;
+ interrupt-parent = <&pmicintc>;
+ interrupts = <192 1>, <193 1>, <194 1>,
+ <195 1>, <196 1>, <197 1>,
+ <198 1>, <199 1>, <200 1>,
+ <201 1>, <202 1>, <203 1>,
+ <204 1>, <205 1>, <206 1>,
+ <207 1>, <208 1>, <209 1>,
+ <210 1>, <211 1>, <212 1>,
+ <213 1>, <214 1>, <215 1>,
+ <216 1>, <217 1>, <218 1>,
+ <219 1>, <220 1>, <221 1>,
+ <222 1>, <223 1>, <224 1>,
+ <225 1>, <226 1>, <227 1>,
+ <228 1>, <229 1>, <230 1>,
+ <231 1>, <232 1>, <233 1>,
+ <234 1>, <235 1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ };
+
+ pm8058_mpps: mpps@50 {
+ compatible = "qcom,pm8058-mpp",
+ "qcom,ssbi-mpp";
+ reg = <0x50>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&pmicintc>;
+ interrupts =
+ <128 1>, <129 1>, <130 1>, <131 1>,
+ <132 1>, <133 1>, <134 1>, <135 1>,
+ <136 1>, <137 1>, <138 1>, <139 1>;
+ };
+
pwrkey@1c {
compatible = "qcom,pm8058-pwrkey";
reg = <0x1c>;
row-hold = <91500>;
};
- rtc@11d {
+ rtc@1e8 {
compatible = "qcom,pm8058-rtc";
+ reg = <0x1e8>;
interrupt-parent = <&pmicintc>;
interrupts = <39 1>;
- reg = <0x11d>;
allow-set-time;
};
};
};
- /* Temporary fixed regulator */
- vsdcc_fixed: vsdcc-regulator {
- compatible = "regulator-fixed";
- regulator-name = "SDCC Power";
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- regulator-always-on;
+ l2cc: clock-controller@2082000 {
+ compatible = "syscon";
+ reg = <0x02082000 0x1000>;
+ };
+
+ rpm: rpm@104000 {
+ compatible = "qcom,rpm-msm8660";
+ reg = <0x00104000 0x1000>;
+ qcom,ipc = <&l2cc 0x8 2>;
+
+ interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "ack", "err", "wakeup";
+ clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+ clock-names = "ram";
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-apq8660", "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+
+ pm8901-regulators {
+ compatible = "qcom,rpm-pm8901-regulators";
+
+ pm8901_l0: l0 {};
+ pm8901_l1: l1 {};
+ pm8901_l2: l2 {};
+ pm8901_l3: l3 {};
+ pm8901_l4: l4 {};
+ pm8901_l5: l5 {};
+ pm8901_l6: l6 {};
+
+ /* S0 and S1 Handled as SAW regulators by SPM */
+ pm8901_s2: s2 {};
+ pm8901_s3: s3 {};
+ pm8901_s4: s4 {};
+
+ pm8901_lvs0: lvs0 {};
+ pm8901_lvs1: lvs1 {};
+ pm8901_lvs2: lvs2 {};
+ pm8901_lvs3: lvs3 {};
+
+ pm8901_mvs: mvs {};
+ };
+
+ pm8058-regulators {
+ compatible = "qcom,rpm-pm8058-regulators";
+
+ pm8058_l0: l0 {};
+ pm8058_l1: l1 {};
+ pm8058_l2: l2 {};
+ pm8058_l3: l3 {};
+ pm8058_l4: l4 {};
+ pm8058_l5: l5 {};
+ pm8058_l6: l6 {};
+ pm8058_l7: l7 {};
+ pm8058_l8: l8 {};
+ pm8058_l9: l9 {};
+ pm8058_l10: l10 {};
+ pm8058_l11: l11 {};
+ pm8058_l12: l12 {};
+ pm8058_l13: l13 {};
+ pm8058_l14: l14 {};
+ pm8058_l15: l15 {};
+ pm8058_l16: l16 {};
+ pm8058_l17: l17 {};
+ pm8058_l18: l18 {};
+ pm8058_l19: l19 {};
+ pm8058_l20: l20 {};
+ pm8058_l21: l21 {};
+ pm8058_l22: l22 {};
+ pm8058_l23: l23 {};
+ pm8058_l24: l24 {};
+ pm8058_l25: l25 {};
+
+ pm8058_s0: s0 {};
+ pm8058_s1: s1 {};
+ pm8058_s2: s2 {};
+ pm8058_s3: s3 {};
+ pm8058_s4: s4 {};
+
+ pm8058_lvs0: lvs0 {};
+ pm8058_lvs1: lvs1 {};
+
+ pm8058_ncp: ncp {};
+ };
};
amba {
non-removable;
cap-sd-highspeed;
cap-mmc-highspeed;
- vmmc-supply = <&vsdcc_fixed>;
};
sdcc3: sdcc@12180000 {
cap-mmc-highspeed;
max-frequency = <48000000>;
no-1-8-v;
- vmmc-supply = <&vsdcc_fixed>;
+ };
+
+ sdcc5: sdcc@12200000 {
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x00051180>;
+ status = "disabled";
+ reg = <0x12200000 0x8000>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cmd_irq";
+ clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
+ clock-names = "mclk", "apb_pclk";
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <48000000>;
};
};
};
};
+
+ dma-controller@f9944000 {
+ qcom,controlled-remotely;
+ };
};
&spmi_bus {
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8974.h>
#include "skeleton.dtsi"
modem_smp2p_out: master-kernel {
qcom,entry-name = "master-kernel";
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
modem_smp2p_in: slave-kernel {
wcnss_smp2p_out: master-kernel {
qcom,entry-name = "master-kernel";
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
wcnss_smp2p_in: slave-kernel {
apps_smsm: apps@0 {
reg = <0>;
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
modem_smsm: modem@1 {
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm";
+ clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ };
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
+ dma-names = "tx", "rx";
};
spmi_bus: spmi@fc4cf000 {
interrupt-controller;
#interrupt-cells = <4>;
};
+
+ blsp2_dma: dma-controller@f9944000 {
+ compatible = "qcom,bam-v1.4.0";
+ reg = <0xf9944000 0x19000>;
+ interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
};
smd {
rtc@6000 {
compatible = "qcom,pm8941-rtc";
- reg = <0x6000 0x100>,
- <0x6100 0x100>;
+ reg = <0x6000>,
+ <0x6100>;
reg-names = "rtc", "alarm";
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
};
+ pwrkey@800 {
+ compatible = "qcom,pm8941-pwrkey";
+ reg = <0x800>;
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ };
+
pma8084_gpios: gpios@c000 {
compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
- reg = <0xc000 0x1600>;
+ reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
pma8084_mpps: mpps@a000 {
compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp";
- reg = <0xa000 0x800>;
+ reg = <0xa000>;
gpio-controller;
#gpio-cells = <2>;
interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
pma8084_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
- reg = <0x2400 0x100>;
+ reg = <0x2400>;
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
#thermal-sensor-cells = <0>;
io-channels = <&pma8084_vadc VADC_DIE_TEMP>;
pma8084_vadc: vadc@3100 {
compatible = "qcom,spmi-vadc";
- reg = <0x3100 0x100>;
+ reg = <0x3100>;
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
compatible = "renesas,genmai", "renesas,r7s72100";
aliases {
- serial2 = &scif2;
+ serial0 = &scif2;
};
chosen {
bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
- stdout-path = &scif2;
+ stdout-path = "serial0:115200n8";
};
- memory {
+ memory@8000000 {
device_type = "memory";
reg = <0x08000000 0x08000000>;
};
reg = <2 0x00000000 0 0x40000000>;
};
- vcc_mmc0: regulator@0 {
+ vcc_mmc0: regulator-mmc0 {
compatible = "regulator-fixed";
regulator-name = "MMC0 Vcc";
regulator-min-microvolt = <2800000>;
regulator-always-on;
};
- vcc_sdhi0: regulator@1 {
+ vcc_sdhi0: regulator-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
};
/* Common 1.8V and 3.3V rails, used by several devices on APE6EVM */
- ape6evm_fixed_1v8: regulator@2 {
+ ape6evm_fixed_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1V8";
regulator-min-microvolt = <1800000>;
regulator-always-on;
};
- ape6evm_fixed_3v3: regulator@3 {
+ ape6evm_fixed_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3V3";
regulator-min-microvolt = <3300000>;
};
&pfc {
- scifa0_pins: serial0 {
+ scifa0_pins: scifa0 {
groups = "scifa0_data";
function = "scifa0";
};
- mmc0_pins: mmc {
+ mmc0_pins: mmc0 {
groups = "mmc0_data8", "mmc0_ctrl";
function = "mmc0";
};
power-domains = <&pd_a2sl>;
next-level-cache = <&L2_CA15>;
};
+
+ L2_CA15: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ clocks = <&cpg_clocks R8A73A4_CLK_Z>;
+ power-domains = <&pd_a3sm>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ L2_CA7: cache-controller@100 {
+ compatible = "cache";
+ reg = <0x100>;
+ clocks = <&cpg_clocks R8A73A4_CLK_Z2>;
+ power-domains = <&pd_a3km>;
+ cache-unified;
+ cache-level = <2>;
+ };
};
ptm {
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
- L2_CA15: cache-controller@0 {
- compatible = "cache";
- clocks = <&cpg_clocks R8A73A4_CLK_Z>;
- power-domains = <&pd_a3sm>;
- cache-unified;
- cache-level = <2>;
- };
-
- L2_CA7: cache-controller@1 {
- compatible = "cache";
- clocks = <&cpg_clocks R8A73A4_CLK_Z2>;
- power-domains = <&pd_a3km>;
- cache-unified;
- cache-level = <2>;
- };
-
dbsc1: memory-controller@e6790000 {
compatible = "renesas,dbsc-r8a73a4";
reg = <0 0xe6790000 0 0x10000>;
compatible = "renesas,armadillo800eva", "renesas,r8a7740";
aliases {
- serial1 = &scifa1;
+ serial0 = &scifa1;
};
chosen {
- bootargs = "console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp rw";
- stdout-path = &scifa1;
+ bootargs = "earlyprintk ignore_loglevel root=/dev/nfs ip=dhcp rw";
+ stdout-path = "serial0:115200n8";
};
- memory {
+ memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x20000000>;
};
- reg_3p3v: regulator@0 {
+ reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-boot-on;
};
- vcc_sdhi0: regulator@1 {
+ vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
enable-active-high;
};
- vccq_sdhi0: regulator@2 {
+ vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
enable-active-high;
};
- reg_5p0v: regulator@3 {
+ reg_5p0v: regulator-5p0v {
compatible = "regulator-fixed";
regulator-name = "fixed-5.0V";
regulator-min-microvolt = <5000000>;
};
};
- i2c2: i2c@2 {
+ i2c2: i2c-2 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
function = "gether";
};
- scifa1_pins: serial1 {
+ scifa1_pins: scifa1 {
groups = "scifa1_data";
function = "scifa1";
};
<0xc2000000 0x1000>;
};
- L2: cache-controller {
+ L2: cache-controller@f0100000 {
compatible = "arm,pl310-cache";
reg = <0xf0100000 0x1000>;
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
stdout-path = "serial0:115200n8";
};
- memory {
+ memory@60000000 {
device_type = "memory";
reg = <0x60000000 0x10000000>;
};
- fixedregulator3v3: fixedregulator@0 {
+ fixedregulator3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
- scif0_pins: serial0 {
+ scif0_pins: scif0 {
groups = "scif0_data_a", "scif0_ctrl";
function = "scif0";
};
pinctrl-0 = <&scif0_pins>;
pinctrl-names = "default";
+ uart-has-rtscts;
status = "okay";
};
status = "disabled";
rcar_sound,src {
- src3: src@3 { };
- src4: src@4 { };
- src5: src@5 { };
- src6: src@6 { };
- src7: src@7 { };
- src8: src@8 { };
- src9: src@9 { };
+ src3: src-3 { };
+ src4: src-4 { };
+ src5: src-5 { };
+ src6: src-6 { };
+ src7: src-7 { };
+ src8: src-8 { };
+ src9: src-9 { };
};
rcar_sound,ssi {
- ssi3: ssi@3 { interrupts = <GIC_SPI 0x85 IRQ_TYPE_LEVEL_HIGH>; };
- ssi4: ssi@4 { interrupts = <GIC_SPI 0x85 IRQ_TYPE_LEVEL_HIGH>; };
- ssi5: ssi@5 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
- ssi6: ssi@6 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
- ssi7: ssi@7 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
- ssi8: ssi@8 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
- ssi9: ssi@9 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
+ ssi3: ssi-3 { interrupts = <GIC_SPI 0x85 IRQ_TYPE_LEVEL_HIGH>; };
+ ssi4: ssi-4 { interrupts = <GIC_SPI 0x85 IRQ_TYPE_LEVEL_HIGH>; };
+ ssi5: ssi-5 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
+ ssi6: ssi-6 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
+ ssi7: ssi-7 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
+ ssi8: ssi-8 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
+ ssi9: ssi-9 { interrupts = <GIC_SPI 0x86 IRQ_TYPE_LEVEL_HIGH>; };
};
};
chosen {
bootargs = "ignore_loglevel root=/dev/nfs ip=on";
- stdout-path = &scif2;
+ stdout-path = "serial0:115200n8";
};
- memory {
+ memory@60000000 {
device_type = "memory";
reg = <0x60000000 0x40000000>;
};
- fixedregulator3v3: fixedregulator@0 {
+ fixedregulator3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
};
};
- scif2_pins: serial2 {
+ scif2_pins: scif2 {
groups = "scif2_data_c";
function = "scif2";
};
- scif4_pins: serial4 {
+ scif4_pins: scif4 {
groups = "scif4_data";
function = "scif4";
};
keyboard {
compatible = "gpio-keys";
- button@1 {
+ one {
linux,code = <KEY_1>;
label = "SW2-1";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
};
- button@2 {
+ two {
linux,code = <KEY_2>;
label = "SW2-2";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
};
- button@3 {
+ three {
linux,code = <KEY_3>;
label = "SW2-3";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
};
- button@4 {
+ four {
linux,code = <KEY_4>;
label = "SW2-4";
wakeup-source;
};
};
- fixedregulator3v3: fixedregulator@0 {
+ fixedregulator3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-always-on;
};
- vcc_sdhi0: regulator@1 {
+ vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
enable-active-high;
};
- vccq_sdhi0: regulator@2 {
+ vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
1800000 0>;
};
- vcc_sdhi2: regulator@3 {
+ vcc_sdhi2: regulator-vcc-sdhi2 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
enable-active-high;
};
- vccq_sdhi2: regulator@4 {
+ vccq_sdhi2: regulator-vccq-sdhi2 {
compatible = "regulator-gpio";
regulator-name = "SDHI2 VccQ";
* instantiate the slave device at runtime according to the documentation.
* You can then communicate with the slave via IIC3.
*/
- i2cexio: i2c@8 {
+ i2cexio: i2c-8 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic0>, <&i2c0>;
i2c-bus-name = "i2c-exio";
function = "du";
};
- scif0_pins: serial0 {
+ scif0_pins: scif0 {
groups = "scif0_data";
function = "scif0";
};
function = "intc";
};
- scifa1_pins: serial1 {
+ scifa1_pins: scifa1 {
groups = "scifa1_data";
function = "scifa1";
};
function = "mmc1";
};
- qspi_pins: spi0 {
+ qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
- msiof1_pins: spi2 {
+ msiof1_pins: msiof1 {
groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
"msiof1_tx";
function = "msiof1";
function = "usb2";
};
- vin1_pins: vin {
+ vin1_pins: vin1 {
groups = "vin1_data8", "vin1_clk";
function = "vin1";
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
+ enable-method = "renesas,apmu";
cpu0: cpu@0 {
device_type = "cpu";
next-level-cache = <&L2_CA15>;
};
- cpu4: cpu@4 {
+ cpu4: cpu@100 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0x100>;
next-level-cache = <&L2_CA7>;
};
- cpu5: cpu@5 {
+ cpu5: cpu@101 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0x101>;
next-level-cache = <&L2_CA7>;
};
- cpu6: cpu@6 {
+ cpu6: cpu@102 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0x102>;
next-level-cache = <&L2_CA7>;
};
- cpu7: cpu@7 {
+ cpu7: cpu@103 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0x103>;
power-domains = <&sysc R8A7790_PD_CA7_CPU3>;
next-level-cache = <&L2_CA7>;
};
+
+ L2_CA15: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ power-domains = <&sysc R8A7790_PD_CA15_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ L2_CA7: cache-controller@100 {
+ compatible = "cache";
+ reg = <0x100>;
+ power-domains = <&sysc R8A7790_PD_CA7_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
};
thermal-zones {
};
};
- L2_CA15: cache-controller@0 {
- compatible = "cache";
- power-domains = <&sysc R8A7790_PD_CA15_SCU>;
- cache-unified;
- cache-level = <2>;
+ apmu@e6151000 {
+ compatible = "renesas,r8a7790-apmu", "renesas,apmu";
+ reg = <0 0xe6151000 0 0x188>;
+ cpus = <&cpu4 &cpu5 &cpu6 &cpu7>;
};
- L2_CA7: cache-controller@1 {
- compatible = "cache";
- power-domains = <&sysc R8A7790_PD_CA7_SCU>;
- cache-unified;
- cache-level = <2>;
+ apmu@e6152000 {
+ compatible = "renesas,r8a7790-apmu", "renesas,apmu";
+ reg = <0 0xe6152000 0 0x188>;
+ cpus = <&cpu0 &cpu1 &cpu2 &cpu3>;
};
gic: interrupt-controller@f1001000 {
reg = <0 0xe6500000 0 0x425>;
interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_IIC0>;
- dmas = <&dmac0 0x61>, <&dmac0 0x62>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+ <&dmac1 0x61>, <&dmac1 0x62>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6510000 0 0x425>;
interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_IIC1>;
- dmas = <&dmac0 0x65>, <&dmac0 0x66>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+ <&dmac1 0x65>, <&dmac1 0x66>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6520000 0 0x425>;
interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_IIC2>;
- dmas = <&dmac0 0x69>, <&dmac0 0x6a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x69>, <&dmac0 0x6a>,
+ <&dmac1 0x69>, <&dmac1 0x6a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe60b0000 0 0x425>;
interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7790_CLK_IICDVFS>;
- dmas = <&dmac0 0x77>, <&dmac0 0x78>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+ <&dmac1 0x77>, <&dmac1 0x78>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee200000 0 0x80>;
interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_MMCIF0>;
- dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+ <&dmac1 0xd1>, <&dmac1 0xd2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
reg = <0 0xee220000 0 0x80>;
interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_MMCIF1>;
- dmas = <&dmac0 0xe1>, <&dmac0 0xe2>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xe1>, <&dmac0 0xe2>,
+ <&dmac1 0xe1>, <&dmac1 0xe2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
reg = <0 0xee100000 0 0x328>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_SDHI0>;
- dmas = <&dmac1 0xcd>, <&dmac1 0xce>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
+ <&dmac1 0xcd>, <&dmac1 0xce>;
+ dma-names = "tx", "rx", "tx", "rx";
max-frequency = <195000000>;
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
reg = <0 0xee120000 0 0x328>;
interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_SDHI1>;
- dmas = <&dmac1 0xc9>, <&dmac1 0xca>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xc9>, <&dmac0 0xca>,
+ <&dmac1 0xc9>, <&dmac1 0xca>;
+ dma-names = "tx", "rx", "tx", "rx";
max-frequency = <195000000>;
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
reg = <0 0xee140000 0 0x100>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_SDHI2>;
- dmas = <&dmac1 0xc1>, <&dmac1 0xc2>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
+ <&dmac1 0xc1>, <&dmac1 0xc2>;
+ dma-names = "tx", "rx", "tx", "rx";
max-frequency = <97500000>;
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
reg = <0 0xee160000 0 0x100>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_SDHI3>;
- dmas = <&dmac1 0xd3>, <&dmac1 0xd4>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
+ <&dmac1 0xd3>, <&dmac1 0xd4>;
+ dma-names = "tx", "rx", "tx", "rx";
max-frequency = <97500000>;
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>;
clock-names = "fck";
- dmas = <&dmac0 0x21>, <&dmac0 0x22>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+ <&dmac1 0x21>, <&dmac1 0x22>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFA1>;
clock-names = "fck";
- dmas = <&dmac0 0x25>, <&dmac0 0x26>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+ <&dmac1 0x25>, <&dmac1 0x26>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFA2>;
clock-names = "fck";
- dmas = <&dmac0 0x27>, <&dmac0 0x28>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+ <&dmac1 0x27>, <&dmac1 0x28>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFB0>;
clock-names = "fck";
- dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+ <&dmac1 0x3d>, <&dmac1 0x3e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFB1>;
clock-names = "fck";
- dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+ <&dmac1 0x19>, <&dmac1 0x1a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFB2>;
clock-names = "fck";
- dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+ <&dmac1 0x1d>, <&dmac1 0x1e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7790_CLK_SCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+ <&dmac1 0x29>, <&dmac1 0x2a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7790_CLK_SCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+ <&dmac1 0x2d>, <&dmac1 0x2e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp3_clks R8A7790_CLK_SCIF2>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+ <&dmac1 0x2b>, <&dmac1 0x2c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7790_CLK_HSCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+ <&dmac1 0x39>, <&dmac1 0x3a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7790_CLK_HSCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+ <&dmac1 0x4d>, <&dmac1 0x4e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6b10000 0 0x2c>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7790_CLK_QSPI_MOD>;
- dmas = <&dmac0 0x17>, <&dmac0 0x18>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+ <&dmac1 0x17>, <&dmac1 0x18>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
reg = <0 0xe6e20000 0 0x0064>;
interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7790_CLK_MSIOF0>;
- dmas = <&dmac0 0x51>, <&dmac0 0x52>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+ <&dmac1 0x51>, <&dmac1 0x52>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6e10000 0 0x0064>;
interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_MSIOF1>;
- dmas = <&dmac0 0x55>, <&dmac0 0x56>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+ <&dmac1 0x55>, <&dmac1 0x56>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6e00000 0 0x0064>;
interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_MSIOF2>;
- dmas = <&dmac0 0x41>, <&dmac0 0x42>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x41>, <&dmac0 0x42>,
+ <&dmac1 0x41>, <&dmac1 0x42>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6c90000 0 0x0064>;
interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_MSIOF3>;
- dmas = <&dmac0 0x45>, <&dmac0 0x46>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x45>, <&dmac0 0x46>,
+ <&dmac1 0x45>, <&dmac1 0x46>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
rcar_sound,dvc {
- dvc0: dvc@0 {
+ dvc0: dvc-0 {
dmas = <&audma0 0xbc>;
dma-names = "tx";
};
- dvc1: dvc@1 {
+ dvc1: dvc-1 {
dmas = <&audma0 0xbe>;
dma-names = "tx";
};
};
rcar_sound,mix {
- mix0: mix@0 { };
- mix1: mix@1 { };
+ mix0: mix-0 { };
+ mix1: mix-1 { };
};
rcar_sound,ctu {
- ctu00: ctu@0 { };
- ctu01: ctu@1 { };
- ctu02: ctu@2 { };
- ctu03: ctu@3 { };
- ctu10: ctu@4 { };
- ctu11: ctu@5 { };
- ctu12: ctu@6 { };
- ctu13: ctu@7 { };
+ ctu00: ctu-0 { };
+ ctu01: ctu-1 { };
+ ctu02: ctu-2 { };
+ ctu03: ctu-3 { };
+ ctu10: ctu-4 { };
+ ctu11: ctu-5 { };
+ ctu12: ctu-6 { };
+ ctu13: ctu-7 { };
};
rcar_sound,src {
- src0: src@0 {
+ src0: src-0 {
interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x85>, <&audma1 0x9a>;
dma-names = "rx", "tx";
};
- src1: src@1 {
+ src1: src-1 {
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x87>, <&audma1 0x9c>;
dma-names = "rx", "tx";
};
- src2: src@2 {
+ src2: src-2 {
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x89>, <&audma1 0x9e>;
dma-names = "rx", "tx";
};
- src3: src@3 {
+ src3: src-3 {
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8b>, <&audma1 0xa0>;
dma-names = "rx", "tx";
};
- src4: src@4 {
+ src4: src-4 {
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8d>, <&audma1 0xb0>;
dma-names = "rx", "tx";
};
- src5: src@5 {
+ src5: src-5 {
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8f>, <&audma1 0xb2>;
dma-names = "rx", "tx";
};
- src6: src@6 {
+ src6: src-6 {
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x91>, <&audma1 0xb4>;
dma-names = "rx", "tx";
};
- src7: src@7 {
+ src7: src-7 {
interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x93>, <&audma1 0xb6>;
dma-names = "rx", "tx";
};
- src8: src@8 {
+ src8: src-8 {
interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x95>, <&audma1 0xb8>;
dma-names = "rx", "tx";
};
- src9: src@9 {
+ src9: src-9 {
interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x97>, <&audma1 0xba>;
dma-names = "rx", "tx";
};
rcar_sound,ssi {
- ssi0: ssi@0 {
+ ssi0: ssi-0 {
interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi1: ssi@1 {
+ ssi1: ssi-1 {
interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi2: ssi@2 {
+ ssi2: ssi-2 {
interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi3: ssi@3 {
+ ssi3: ssi-3 {
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi4: ssi@4 {
+ ssi4: ssi-4 {
interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi5: ssi@5 {
+ ssi5: ssi-5 {
interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi6: ssi@6 {
+ ssi6: ssi-6 {
interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi7: ssi@7 {
+ ssi7: ssi-7 {
interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi8: ssi@8 {
+ ssi8: ssi-8 {
interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi9: ssi@9 {
+ ssi9: ssi-9 {
interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>;
dma-names = "rx", "tx", "rxu", "txu";
};
};
- vcc_sdhi0: regulator@0 {
+ vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
enable-active-high;
};
- vccq_sdhi0: regulator@1 {
+ vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
1800000 0>;
};
- vcc_sdhi1: regulator@2 {
+ vcc_sdhi1: regulator-vcc-sdhi1 {
compatible = "regulator-fixed";
regulator-name = "SDHI1 Vcc";
enable-active-high;
};
- vccq_sdhi1: regulator@3 {
+ vccq_sdhi1: regulator-vccq-sdhi1 {
compatible = "regulator-gpio";
regulator-name = "SDHI1 VccQ";
1800000 0>;
};
- vcc_sdhi2: regulator@4 {
+ vcc_sdhi2: regulator-vcc-sdhi2 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
enable-active-high;
};
- vccq_sdhi2: regulator@5 {
+ vccq_sdhi2: regulator-vccq-sdhi2 {
compatible = "regulator-gpio";
regulator-name = "SDHI2 VccQ";
function = "du";
};
- scif0_pins: serial0 {
+ scif0_pins: scif0 {
groups = "scif0_data_d";
function = "scif0";
};
- scif1_pins: serial1 {
+ scif1_pins: scif1 {
groups = "scif1_data_d";
function = "scif1";
};
function = "sdhi2";
};
- qspi_pins: spi0 {
+ qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
- msiof0_pins: spi1 {
+ msiof0_pins: msiof0 {
groups = "msiof0_clk", "msiof0_sync", "msiof0_rx",
"msiof0_tx";
function = "msiof0";
reg = <2 0x00000000 0 0x40000000>;
};
- vcc_sdhi0: regulator@0 {
+ vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
regulator-always-on;
};
- vccq_sdhi0: regulator@1 {
+ vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
1800000 0>;
};
- vcc_sdhi2: regulator@2 {
+ vcc_sdhi2: regulator-vcc-sdhi2 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
regulator-always-on;
};
- vccq_sdhi2: regulator@3 {
+ vccq_sdhi2: regulator-vccq-sdhi2 {
compatible = "regulator-gpio";
regulator-name = "SDHI2 VccQ";
};
&pfc {
- scif0_pins: serial0 {
+ scif0_pins: scif0 {
groups = "scif0_data_d";
function = "scif0";
};
function = "sdhi2";
};
- qspi_pins: spi0 {
+ qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
+ enable-method = "renesas,apmu";
cpu0: cpu@0 {
device_type = "cpu";
power-domains = <&sysc R8A7791_PD_CA15_CPU1>;
next-level-cache = <&L2_CA15>;
};
+
+ L2_CA15: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ power-domains = <&sysc R8A7791_PD_CA15_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
};
thermal-zones {
};
};
- L2_CA15: cache-controller@0 {
- compatible = "cache";
- power-domains = <&sysc R8A7791_PD_CA15_SCU>;
- cache-unified;
- cache-level = <2>;
+ apmu@e6152000 {
+ compatible = "renesas,r8a7791-apmu", "renesas,apmu";
+ reg = <0 0xe6152000 0 0x188>;
+ cpus = <&cpu0 &cpu1>;
};
gic: interrupt-controller@f1001000 {
reg = <0 0xe60b0000 0 0x425>;
interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_IICDVFS>;
- dmas = <&dmac0 0x77>, <&dmac0 0x78>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+ <&dmac1 0x77>, <&dmac1 0x78>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6500000 0 0x425>;
interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_IIC0>;
- dmas = <&dmac0 0x61>, <&dmac0 0x62>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+ <&dmac1 0x61>, <&dmac1 0x62>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6510000 0 0x425>;
interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_IIC1>;
- dmas = <&dmac0 0x65>, <&dmac0 0x66>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+ <&dmac1 0x65>, <&dmac1 0x66>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee200000 0 0x80>;
interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_MMCIF0>;
- dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+ <&dmac1 0xd1>, <&dmac1 0xd2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
reg = <0 0xee100000 0 0x328>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_SDHI0>;
- dmas = <&dmac1 0xcd>, <&dmac1 0xce>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
+ <&dmac1 0xcd>, <&dmac1 0xce>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee140000 0 0x100>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_SDHI1>;
- dmas = <&dmac1 0xc1>, <&dmac1 0xc2>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
+ <&dmac1 0xc1>, <&dmac1 0xc2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee160000 0 0x100>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_SDHI2>;
- dmas = <&dmac1 0xd3>, <&dmac1 0xd4>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
+ <&dmac1 0xd3>, <&dmac1 0xd4>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFA0>;
clock-names = "fck";
- dmas = <&dmac0 0x21>, <&dmac0 0x22>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+ <&dmac1 0x21>, <&dmac1 0x22>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFA1>;
clock-names = "fck";
- dmas = <&dmac0 0x25>, <&dmac0 0x26>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+ <&dmac1 0x25>, <&dmac1 0x26>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFA2>;
clock-names = "fck";
- dmas = <&dmac0 0x27>, <&dmac0 0x28>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+ <&dmac1 0x27>, <&dmac1 0x28>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7791_CLK_SCIFA3>;
clock-names = "fck";
- dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1b>, <&dmac0 0x1c>,
+ <&dmac1 0x1b>, <&dmac1 0x1c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7791_CLK_SCIFA4>;
clock-names = "fck";
- dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1f>, <&dmac0 0x20>,
+ <&dmac1 0x1f>, <&dmac1 0x20>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7791_CLK_SCIFA5>;
clock-names = "fck";
- dmas = <&dmac0 0x23>, <&dmac0 0x24>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x23>, <&dmac0 0x24>,
+ <&dmac1 0x23>, <&dmac1 0x24>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFB0>;
clock-names = "fck";
- dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+ <&dmac1 0x3d>, <&dmac1 0x3e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFB1>;
clock-names = "fck";
- dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+ <&dmac1 0x19>, <&dmac1 0x1a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFB2>;
clock-names = "fck";
- dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+ <&dmac1 0x1d>, <&dmac1 0x1e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_SCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+ <&dmac1 0x29>, <&dmac1 0x2a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_SCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+ <&dmac1 0x2d>, <&dmac1 0x2e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_SCIF2>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+ <&dmac1 0x2b>, <&dmac1 0x2c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_SCIF3>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+ <&dmac1 0x2f>, <&dmac1 0x30>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_SCIF4>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xfb>, <&dmac0 0xfc>,
+ <&dmac1 0xfb>, <&dmac1 0xfc>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_SCIF5>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xfd>, <&dmac0 0xfe>,
+ <&dmac1 0xfd>, <&dmac1 0xfe>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_HSCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+ <&dmac1 0x39>, <&dmac1 0x3a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_HSCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+ <&dmac1 0x4d>, <&dmac1 0x4e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7791_CLK_HSCIF2>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x3b>, <&dmac0 0x3c>,
+ <&dmac1 0x3b>, <&dmac1 0x3c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6b10000 0 0x2c>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>;
- dmas = <&dmac0 0x17>, <&dmac0 0x18>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+ <&dmac1 0x17>, <&dmac1 0x18>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
reg = <0 0xe6e20000 0 0x0064>;
interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
- dmas = <&dmac0 0x51>, <&dmac0 0x52>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+ <&dmac1 0x51>, <&dmac1 0x52>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6e10000 0 0x0064>;
interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_MSIOF1>;
- dmas = <&dmac0 0x55>, <&dmac0 0x56>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+ <&dmac1 0x55>, <&dmac1 0x56>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6e00000 0 0x0064>;
interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_MSIOF2>;
- dmas = <&dmac0 0x41>, <&dmac0 0x42>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x41>, <&dmac0 0x42>,
+ <&dmac1 0x41>, <&dmac1 0x42>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
rcar_sound,dvc {
- dvc0: dvc@0 {
+ dvc0: dvc-0 {
dmas = <&audma0 0xbc>;
dma-names = "tx";
};
- dvc1: dvc@1 {
+ dvc1: dvc-1 {
dmas = <&audma0 0xbe>;
dma-names = "tx";
};
};
rcar_sound,mix {
- mix0: mix@0 { };
- mix1: mix@1 { };
+ mix0: mix-0 { };
+ mix1: mix-1 { };
};
rcar_sound,ctu {
- ctu00: ctu@0 { };
- ctu01: ctu@1 { };
- ctu02: ctu@2 { };
- ctu03: ctu@3 { };
- ctu10: ctu@4 { };
- ctu11: ctu@5 { };
- ctu12: ctu@6 { };
- ctu13: ctu@7 { };
+ ctu00: ctu-0 { };
+ ctu01: ctu-1 { };
+ ctu02: ctu-2 { };
+ ctu03: ctu-3 { };
+ ctu10: ctu-4 { };
+ ctu11: ctu-5 { };
+ ctu12: ctu-6 { };
+ ctu13: ctu-7 { };
};
rcar_sound,src {
- src0: src@0 {
+ src0: src-0 {
interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x85>, <&audma1 0x9a>;
dma-names = "rx", "tx";
};
- src1: src@1 {
+ src1: src-1 {
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x87>, <&audma1 0x9c>;
dma-names = "rx", "tx";
};
- src2: src@2 {
+ src2: src-2 {
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x89>, <&audma1 0x9e>;
dma-names = "rx", "tx";
};
- src3: src@3 {
+ src3: src-3 {
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8b>, <&audma1 0xa0>;
dma-names = "rx", "tx";
};
- src4: src@4 {
+ src4: src-4 {
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8d>, <&audma1 0xb0>;
dma-names = "rx", "tx";
};
- src5: src@5 {
+ src5: src-5 {
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8f>, <&audma1 0xb2>;
dma-names = "rx", "tx";
};
- src6: src@6 {
+ src6: src-6 {
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x91>, <&audma1 0xb4>;
dma-names = "rx", "tx";
};
- src7: src@7 {
+ src7: src-7 {
interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x93>, <&audma1 0xb6>;
dma-names = "rx", "tx";
};
- src8: src@8 {
+ src8: src-8 {
interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x95>, <&audma1 0xb8>;
dma-names = "rx", "tx";
};
- src9: src@9 {
+ src9: src-9 {
interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x97>, <&audma1 0xba>;
dma-names = "rx", "tx";
};
rcar_sound,ssi {
- ssi0: ssi@0 {
+ ssi0: ssi-0 {
interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi1: ssi@1 {
+ ssi1: ssi-1 {
interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi2: ssi@2 {
+ ssi2: ssi-2 {
interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi3: ssi@3 {
+ ssi3: ssi-3 {
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi4: ssi@4 {
+ ssi4: ssi-4 {
interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi5: ssi@5 {
+ ssi5: ssi-5 {
interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi6: ssi@6 {
+ ssi6: ssi-6 {
interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi7: ssi@7 {
+ ssi7: ssi-7 {
interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi8: ssi@8 {
+ ssi8: ssi-8 {
interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi9: ssi@9 {
+ ssi9: ssi-9 {
interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>;
dma-names = "rx", "tx", "rxu", "txu";
--- /dev/null
+/*
+ * Device Tree Source for the Blanche board
+ *
+ * Copyright (C) 2014 Renesas Electronics Corporation
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a7792.dtsi"
+
+/ {
+ model = "Blanche";
+ compatible = "renesas,blanche", "renesas,r8a7792";
+
+ aliases {
+ serial0 = &scif0;
+ serial1 = &scif3;
+ };
+
+ chosen {
+ bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x40000000>;
+ };
+
+ d3_3v: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "D3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ethernet@18000000 {
+ compatible = "smsc,lan89218", "smsc,lan9115";
+ reg = <0 0x18000000 0 0x100>;
+ phy-mode = "mii";
+ interrupt-parent = <&irqc>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ smsc,irq-push-pull;
+ reg-io-width = <4>;
+ vddvario-supply = <&d3_3v>;
+ vdd33a-supply = <&d3_3v>;
+ };
+};
+
+&extal_clk {
+ clock-frequency = <20000000>;
+};
+
+&scif0 {
+ status = "okay";
+};
+
+&scif3 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Device Tree Source for the r8a7792 SoC
+ *
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/clock/r8a7792-clock.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a7792-sysc.h>
+
+/ {
+ compatible = "renesas,r8a7792";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "renesas,apmu";
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <0>;
+ clock-frequency = <1000000000>;
+ clocks = <&cpg_clocks R8A7792_CLK_Z>;
+ power-domains = <&sysc R8A7792_PD_CA15_CPU0>;
+ next-level-cache = <&L2_CA15>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ clock-frequency = <1000000000>;
+ power-domains = <&sysc R8A7792_PD_CA15_CPU1>;
+ next-level-cache = <&L2_CA15>;
+ };
+
+ L2_CA15: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ cache-unified;
+ cache-level = <2>;
+ power-domains = <&sysc R8A7792_PD_CA15_SCU>;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ apmu@e6152000 {
+ compatible = "renesas,r8a7792-apmu", "renesas,apmu";
+ reg = <0 0xe6152000 0 0x188>;
+ cpus = <&cpu0 &cpu1>;
+ };
+
+ gic: interrupt-controller@f1001000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0 0xf1001000 0 0x1000>,
+ <0 0xf1002000 0 0x1000>,
+ <0 0xf1004000 0 0x2000>,
+ <0 0xf1006000 0 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ irqc: interrupt-controller@e61c0000 {
+ compatible = "renesas,irqc-r8a7792", "renesas,irqc";
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <0 0xe61c0000 0 0x200>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp4_clks R8A7792_CLK_IRQC>;
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7792-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
+ dmac0: dma-controller@e6700000 {
+ compatible = "renesas,dmac-r8a7792",
+ "renesas,rcar-dmac";
+ reg = <0 0xe6700000 0 0x20000>;
+ interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14";
+ clocks = <&mstp2_clks R8A7792_CLK_SYS_DMAC0>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <15>;
+ };
+
+ dmac1: dma-controller@e6720000 {
+ compatible = "renesas,dmac-r8a7792",
+ "renesas,rcar-dmac";
+ reg = <0 0xe6720000 0 0x20000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14";
+ clocks = <&mstp2_clks R8A7792_CLK_SYS_DMAC1>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <15>;
+ };
+
+ scif0: serial@e6e60000 {
+ compatible = "renesas,scif-r8a7792",
+ "renesas,rcar-gen2-scif", "renesas,scif";
+ reg = <0 0xe6e60000 0 64>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp7_clks R8A7792_CLK_SCIF0>, <&zs_clk>,
+ <&scif_clk>;
+ clock-names = "fck", "brg_int", "scif_clk";
+ dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+ <&dmac1 0x29>, <&dmac1 0x2a>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ scif1: serial@e6e68000 {
+ compatible = "renesas,scif-r8a7792",
+ "renesas,rcar-gen2-scif", "renesas,scif";
+ reg = <0 0xe6e68000 0 64>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp7_clks R8A7792_CLK_SCIF1>, <&zs_clk>,
+ <&scif_clk>;
+ clock-names = "fck", "brg_int", "scif_clk";
+ dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+ <&dmac1 0x2d>, <&dmac1 0x2e>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ scif2: serial@e6e58000 {
+ compatible = "renesas,scif-r8a7792",
+ "renesas,rcar-gen2-scif", "renesas,scif";
+ reg = <0 0xe6e58000 0 64>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp7_clks R8A7792_CLK_SCIF2>, <&zs_clk>,
+ <&scif_clk>;
+ clock-names = "fck", "brg_int", "scif_clk";
+ dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+ <&dmac1 0x2b>, <&dmac1 0x2c>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ scif3: serial@e6ea8000 {
+ compatible = "renesas,scif-r8a7792",
+ "renesas,rcar-gen2-scif", "renesas,scif";
+ reg = <0 0xe6ea8000 0 64>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp7_clks R8A7792_CLK_SCIF3>, <&zs_clk>,
+ <&scif_clk>;
+ clock-names = "fck", "brg_int", "scif_clk";
+ dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+ <&dmac1 0x2f>, <&dmac1 0x30>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ hscif0: serial@e62c0000 {
+ compatible = "renesas,hscif-r8a7792",
+ "renesas,rcar-gen2-hscif", "renesas,hscif";
+ reg = <0 0xe62c0000 0 96>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp7_clks R8A7792_CLK_HSCIF0>, <&zs_clk>,
+ <&scif_clk>;
+ clock-names = "fck", "brg_int", "scif_clk";
+ dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+ <&dmac1 0x39>, <&dmac1 0x3a>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ hscif1: serial@e62c8000 {
+ compatible = "renesas,hscif-r8a7792",
+ "renesas,rcar-gen2-hscif", "renesas,hscif";
+ reg = <0 0xe62c8000 0 96>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp7_clks R8A7792_CLK_HSCIF1>, <&zs_clk>,
+ <&scif_clk>;
+ clock-names = "fck", "brg_int", "scif_clk";
+ dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+ <&dmac1 0x4d>, <&dmac1 0x4e>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ jpu: jpeg-codec@fe980000 {
+ compatible = "renesas,jpu-r8a7792",
+ "renesas,rcar-gen2-jpu";
+ reg = <0 0xfe980000 0 0x10300>;
+ interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp1_clks R8A7792_CLK_JPU>;
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ };
+
+ /* Special CPG clocks */
+ cpg_clocks: cpg_clocks@e6150000 {
+ compatible = "renesas,r8a7792-cpg-clocks",
+ "renesas,rcar-gen2-cpg-clocks";
+ reg = <0 0xe6150000 0 0x1000>;
+ clocks = <&extal_clk>;
+ #clock-cells = <1>;
+ clock-output-names = "main", "pll0", "pll1", "pll3",
+ "lb", "qspi", "z";
+ #power-domain-cells = <0>;
+ };
+
+ /* Fixed factor clocks */
+ pll1_div2_clk: pll1_div2 {
+ compatible = "fixed-factor-clock";
+ clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+ #clock-cells = <0>;
+ clock-div = <2>;
+ clock-mult = <1>;
+ };
+ zs_clk: zs {
+ compatible = "fixed-factor-clock";
+ clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+ #clock-cells = <0>;
+ clock-div = <6>;
+ clock-mult = <1>;
+ };
+ p_clk: p {
+ compatible = "fixed-factor-clock";
+ clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+ #clock-cells = <0>;
+ clock-div = <24>;
+ clock-mult = <1>;
+ };
+ cp_clk: cp {
+ compatible = "fixed-factor-clock";
+ clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+ #clock-cells = <0>;
+ clock-div = <48>;
+ clock-mult = <1>;
+ };
+ m2_clk: m2 {
+ compatible = "fixed-factor-clock";
+ clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
+ #clock-cells = <0>;
+ clock-div = <8>;
+ clock-mult = <1>;
+ };
+
+ /* Gate clocks */
+ mstp1_clks: mstp1_clks@e6150134 {
+ compatible = "renesas,r8a7792-mstp-clocks",
+ "renesas,cpg-mstp-clocks";
+ reg = <0 0xe6150134 0 4>, <0 0xe6150038 0 4>;
+ clocks = <&m2_clk>;
+ #clock-cells = <1>;
+ clock-indices = <R8A7792_CLK_JPU>;
+ clock-output-names = "jpu";
+ };
+ mstp2_clks: mstp2_clks@e6150138 {
+ compatible = "renesas,r8a7792-mstp-clocks",
+ "renesas,cpg-mstp-clocks";
+ reg = <0 0xe6150138 0 4>, <0 0xe6150040 0 4>;
+ clocks = <&zs_clk>, <&zs_clk>;
+ #clock-cells = <1>;
+ clock-indices = <
+ R8A7792_CLK_SYS_DMAC1 R8A7792_CLK_SYS_DMAC0
+ >;
+ clock-output-names = "sys-dmac1", "sys-dmac0";
+ };
+ mstp4_clks: mstp4_clks@e6150140 {
+ compatible = "renesas,r8a7792-mstp-clocks",
+ "renesas,cpg-mstp-clocks";
+ reg = <0 0xe6150140 0 4>, <0 0xe615004c 0 4>;
+ clocks = <&cp_clk>;
+ #clock-cells = <1>;
+ clock-indices = <R8A7792_CLK_IRQC>;
+ clock-output-names = "irqc";
+ };
+ mstp7_clks: mstp7_clks@e615014c {
+ compatible = "renesas,r8a7792-mstp-clocks",
+ "renesas,cpg-mstp-clocks";
+ reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>;
+ clocks = <&zs_clk>, <&zs_clk>, <&p_clk>, <&p_clk>,
+ <&p_clk>, <&p_clk>;
+ #clock-cells = <1>;
+ clock-indices = <
+ R8A7792_CLK_HSCIF1 R8A7792_CLK_HSCIF0
+ R8A7792_CLK_SCIF3 R8A7792_CLK_SCIF2
+ R8A7792_CLK_SCIF1 R8A7792_CLK_SCIF0
+ >;
+ clock-output-names = "hscif1", "hscif0", "scif3",
+ "scif2", "scif1", "scif0";
+ };
+ };
+
+ /* External root clock */
+ extal_clk: extal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ /* This value must be overridden by the board. */
+ clock-frequency = <0>;
+ };
+
+ /* External SCIF clock */
+ scif_clk: scif {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ /* This value must be overridden by the board. */
+ clock-frequency = <0>;
+ };
+};
};
};
- vcc_sdhi0: regulator@0 {
+ vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
enable-active-high;
};
- vccq_sdhi0: regulator@1 {
+ vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
1800000 0>;
};
- vcc_sdhi1: regulator@2 {
+ vcc_sdhi1: regulator-vcc-sdhi1 {
compatible = "regulator-fixed";
regulator-name = "SDHI1 Vcc";
enable-active-high;
};
- vccq_sdhi1: regulator@3 {
+ vccq_sdhi1: regulator-vccq-sdhi1 {
compatible = "regulator-gpio";
regulator-name = "SDHI1 VccQ";
1800000 0>;
};
- vcc_sdhi2: regulator@4 {
+ vcc_sdhi2: regulator-vcc-sdhi2 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
enable-active-high;
};
- vccq_sdhi2: regulator@5 {
+ vccq_sdhi2: regulator-vccq-sdhi2 {
compatible = "regulator-gpio";
regulator-name = "SDHI2 VccQ";
function = "du";
};
- scif0_pins: serial0 {
+ scif0_pins: scif0 {
groups = "scif0_data_d";
function = "scif0";
};
- scif1_pins: serial1 {
+ scif1_pins: scif1 {
groups = "scif1_data_d";
function = "scif1";
};
renesas,function = "sdhi2";
};
- qspi_pins: spi0 {
+ qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
+ enable-method = "renesas,apmu";
cpu0: cpu@0 {
device_type = "cpu";
< 375000 1000000>;
next-level-cache = <&L2_CA15>;
};
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ clock-frequency = <1500000000>;
+ power-domains = <&sysc R8A7793_PD_CA15_CPU1>;
+ };
+
+ L2_CA15: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ power-domains = <&sysc R8A7793_PD_CA15_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
+ };
+
+ apmu@e6152000 {
+ compatible = "renesas,r8a7793-apmu", "renesas,apmu";
+ reg = <0 0xe6152000 0 0x188>;
+ cpus = <&cpu0 &cpu1>;
};
thermal-zones {
};
};
- L2_CA15: cache-controller@0 {
- compatible = "cache";
- power-domains = <&sysc R8A7793_PD_CA15_SCU>;
- cache-unified;
- cache-level = <2>;
- };
-
gic: interrupt-controller@f1001000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
reg = <0 0xe60b0000 0 0x425>;
interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_IICDVFS>;
- dmas = <&dmac0 0x77>, <&dmac0 0x78>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+ <&dmac1 0x77>, <&dmac1 0x78>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6500000 0 0x425>;
interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7793_CLK_IIC0>;
- dmas = <&dmac0 0x61>, <&dmac0 0x62>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+ <&dmac1 0x61>, <&dmac1 0x62>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6510000 0 0x425>;
interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7793_CLK_IIC1>;
- dmas = <&dmac0 0x65>, <&dmac0 0x66>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+ <&dmac1 0x65>, <&dmac1 0x66>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee100000 0 0x328>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7793_CLK_SDHI0>;
- dmas = <&dmac0 0xcd>, <&dmac0 0xce>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
+ <&dmac1 0xcd>, <&dmac1 0xce>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee140000 0 0x100>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7793_CLK_SDHI1>;
- dmas = <&dmac0 0xc1>, <&dmac0 0xc2>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
+ <&dmac1 0xc1>, <&dmac1 0xc2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee160000 0 0x100>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7793_CLK_SDHI2>;
- dmas = <&dmac0 0xd3>, <&dmac0 0xd4>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
+ <&dmac1 0xd3>, <&dmac1 0xd4>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ mmcif0: mmc@ee200000 {
+ compatible = "renesas,mmcif-r8a7793", "renesas,sh-mmcif";
+ reg = <0 0xee200000 0 0x80>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp3_clks R8A7793_CLK_MMCIF0>;
+ dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+ <&dmac1 0xd1>, <&dmac1 0xd2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
+ reg-io-width = <4>;
status = "disabled";
+ max-frequency = <97500000>;
};
scifa0: serial@e6c40000 {
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFA0>;
clock-names = "fck";
- dmas = <&dmac0 0x21>, <&dmac0 0x22>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+ <&dmac1 0x21>, <&dmac1 0x22>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFA1>;
clock-names = "fck";
- dmas = <&dmac0 0x25>, <&dmac0 0x26>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+ <&dmac1 0x25>, <&dmac1 0x26>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFA2>;
clock-names = "fck";
- dmas = <&dmac0 0x27>, <&dmac0 0x28>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+ <&dmac1 0x27>, <&dmac1 0x28>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7793_CLK_SCIFA3>;
clock-names = "fck";
- dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1b>, <&dmac0 0x1c>,
+ <&dmac1 0x1b>, <&dmac1 0x1c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7793_CLK_SCIFA4>;
clock-names = "fck";
- dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1f>, <&dmac0 0x20>,
+ <&dmac1 0x1f>, <&dmac1 0x20>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7793_CLK_SCIFA5>;
clock-names = "fck";
- dmas = <&dmac0 0x23>, <&dmac0 0x24>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x23>, <&dmac0 0x24>,
+ <&dmac1 0x23>, <&dmac1 0x24>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFB0>;
clock-names = "fck";
- dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+ <&dmac1 0x3d>, <&dmac1 0x3e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFB1>;
clock-names = "fck";
- dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+ <&dmac1 0x19>, <&dmac1 0x1a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFB2>;
clock-names = "fck";
- dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+ <&dmac1 0x1d>, <&dmac1 0x1e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_SCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+ <&dmac1 0x29>, <&dmac1 0x2a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_SCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+ <&dmac1 0x2d>, <&dmac1 0x2e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_SCIF2>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+ <&dmac1 0x2b>, <&dmac1 0x2c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_SCIF3>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+ <&dmac1 0x2f>, <&dmac1 0x30>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_SCIF4>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xfb>, <&dmac0 0xfc>,
+ <&dmac1 0xfb>, <&dmac1 0xfc>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_SCIF5>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xfd>, <&dmac0 0xfe>,
+ <&dmac1 0xfd>, <&dmac1 0xfe>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_HSCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+ <&dmac1 0x39>, <&dmac1 0x3a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_HSCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+ <&dmac1 0x4d>, <&dmac1 0x4e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7793_CLK_HSCIF2>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x3b>, <&dmac0 0x3c>,
+ <&dmac1 0x3b>, <&dmac1 0x3c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6b10000 0 0x2c>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_QSPI_MOD>;
- dmas = <&dmac0 0x17>, <&dmac0 0x18>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+ <&dmac1 0x17>, <&dmac1 0x18>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
status = "disabled";
rcar_sound,dvc {
- dvc0: dvc@0 {
+ dvc0: dvc-0 {
dmas = <&audma0 0xbc>;
dma-names = "tx";
};
- dvc1: dvc@1 {
+ dvc1: dvc-1 {
dmas = <&audma0 0xbe>;
dma-names = "tx";
};
};
rcar_sound,src {
- src0: src@0 {
+ src0: src-0 {
interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x85>, <&audma1 0x9a>;
dma-names = "rx", "tx";
};
- src1: src@1 {
+ src1: src-1 {
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x87>, <&audma1 0x9c>;
dma-names = "rx", "tx";
};
- src2: src@2 {
+ src2: src-2 {
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x89>, <&audma1 0x9e>;
dma-names = "rx", "tx";
};
- src3: src@3 {
+ src3: src-3 {
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8b>, <&audma1 0xa0>;
dma-names = "rx", "tx";
};
- src4: src@4 {
+ src4: src-4 {
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8d>, <&audma1 0xb0>;
dma-names = "rx", "tx";
};
- src5: src@5 {
+ src5: src-5 {
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8f>, <&audma1 0xb2>;
dma-names = "rx", "tx";
};
- src6: src@6 {
+ src6: src-6 {
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x91>, <&audma1 0xb4>;
dma-names = "rx", "tx";
};
- src7: src@7 {
+ src7: src-7 {
interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x93>, <&audma1 0xb6>;
dma-names = "rx", "tx";
};
- src8: src@8 {
+ src8: src-8 {
interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x95>, <&audma1 0xb8>;
dma-names = "rx", "tx";
};
- src9: src@9 {
+ src9: src-9 {
interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x97>, <&audma1 0xba>;
dma-names = "rx", "tx";
};
rcar_sound,ssi {
- ssi0: ssi@0 {
+ ssi0: ssi-0 {
interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi1: ssi@1 {
+ ssi1: ssi-1 {
interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi2: ssi@2 {
+ ssi2: ssi-2 {
interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi3: ssi@3 {
+ ssi3: ssi-3 {
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi4: ssi@4 {
+ ssi4: ssi-4 {
interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi5: ssi@5 {
+ ssi5: ssi-5 {
interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi6: ssi@6 {
+ ssi6: ssi-6 {
interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi7: ssi@7 {
+ ssi7: ssi-7 {
interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi8: ssi@8 {
+ ssi8: ssi-8 {
interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi9: ssi@9 {
+ ssi9: ssi-9 {
interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>;
dma-names = "rx", "tx", "rxu", "txu";
function = "du";
};
- scif2_pins: serial2 {
+ scif2_pins: scif2 {
groups = "scif2_data";
function = "scif2";
};
};
&pfc {
- qspi_pins: spi0 {
+ qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
reg = <0 0x40000000 0 0x40000000>;
};
- d3_3v: regulator@0 {
+ d3_3v: regulator-d3-3v {
compatible = "regulator-fixed";
regulator-name = "D3.3V";
regulator-min-microvolt = <3300000>;
regulator-always-on;
};
- vcc_sdhi1: regulator@3 {
+ vcc_sdhi1: regulator-vcc-sdhi1 {
compatible = "regulator-fixed";
regulator-name = "SDHI1 Vcc";
enable-active-high;
};
- vccq_sdhi1: regulator@4 {
+ vccq_sdhi1: regulator-vccq-sdhi1 {
compatible = "regulator-gpio";
regulator-name = "SDHI1 VccQ";
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
- scif2_pins: serial2 {
+ scif2_pins: scif2 {
groups = "scif2_data";
function = "scif2";
};
function = "sdhi1";
};
- qspi_pins: spi0 {
+ qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
groups = "usb1";
function = "usb1";
};
+
+ du0_pins: du0 {
+ groups = "du0_rgb888", "du0_sync", "du0_disp", "du0_clk0_out";
+ function = "du0";
+ };
+
+ du1_pins: du1 {
+ groups = "du1_rgb666", "du1_sync", "du1_disp", "du1_clk0_out";
+ function = "du1";
+ };
};
&scif2 {
};
&du {
+ pinctrl-0 = <&du0_pins &du1_pins>;
+ pinctrl-names = "default";
status = "okay";
clocks = <&mstp7_clks R8A7794_CLK_DU0>,
power-domains = <&sysc R8A7794_PD_CA7_CPU1>;
next-level-cache = <&L2_CA7>;
};
- };
- L2_CA7: cache-controller@1 {
- compatible = "cache";
- power-domains = <&sysc R8A7794_PD_CA7_SCU>;
- cache-unified;
- cache-level = <2>;
+ L2_CA7: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ power-domains = <&sysc R8A7794_PD_CA7_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
};
gic: interrupt-controller@f1001000 {
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFA0>;
clock-names = "fck";
- dmas = <&dmac0 0x21>, <&dmac0 0x22>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+ <&dmac1 0x21>, <&dmac1 0x22>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFA1>;
clock-names = "fck";
- dmas = <&dmac0 0x25>, <&dmac0 0x26>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+ <&dmac1 0x25>, <&dmac1 0x26>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFA2>;
clock-names = "fck";
- dmas = <&dmac0 0x27>, <&dmac0 0x28>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+ <&dmac1 0x27>, <&dmac1 0x28>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7794_CLK_SCIFA3>;
clock-names = "fck";
- dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1b>, <&dmac0 0x1c>,
+ <&dmac1 0x1b>, <&dmac1 0x1c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7794_CLK_SCIFA4>;
clock-names = "fck";
- dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1f>, <&dmac0 0x20>,
+ <&dmac1 0x1f>, <&dmac1 0x20>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp11_clks R8A7794_CLK_SCIFA5>;
clock-names = "fck";
- dmas = <&dmac0 0x23>, <&dmac0 0x24>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x23>, <&dmac0 0x24>,
+ <&dmac1 0x23>, <&dmac1 0x24>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFB0>;
clock-names = "fck";
- dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+ <&dmac1 0x3d>, <&dmac1 0x3e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFB1>;
clock-names = "fck";
- dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+ <&dmac1 0x19>, <&dmac1 0x1a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFB2>;
clock-names = "fck";
- dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+ <&dmac1 0x1d>, <&dmac1 0x1e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_SCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+ <&dmac1 0x29>, <&dmac1 0x2a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_SCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+ <&dmac1 0x2d>, <&dmac1 0x2e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_SCIF2>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+ <&dmac1 0x2b>, <&dmac1 0x2c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_SCIF3>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+ <&dmac1 0x2f>, <&dmac1 0x30>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_SCIF4>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xfb>, <&dmac0 0xfc>,
+ <&dmac1 0xfb>, <&dmac1 0xfc>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_SCIF5>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xfd>, <&dmac0 0xfe>,
+ <&dmac1 0xfd>, <&dmac1 0xfe>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_HSCIF0>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+ <&dmac1 0x39>, <&dmac1 0x3a>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_HSCIF1>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+ <&dmac1 0x4d>, <&dmac1 0x4e>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
clocks = <&mstp7_clks R8A7794_CLK_HSCIF2>, <&zs_clk>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x3b>, <&dmac0 0x3c>,
+ <&dmac1 0x3b>, <&dmac1 0x3c>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6500000 0 0x425>;
interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_IIC0>;
- dmas = <&dmac0 0x61>, <&dmac0 0x62>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+ <&dmac1 0x61>, <&dmac1 0x62>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6510000 0 0x425>;
interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_IIC1>;
- dmas = <&dmac0 0x65>, <&dmac0 0x66>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+ <&dmac1 0x65>, <&dmac1 0x66>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xee200000 0 0x80>;
interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_MMCIF0>;
- dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+ <&dmac1 0xd1>, <&dmac1 0xd2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
reg = <0 0xee100000 0 0x200>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_SDHI0>;
+ dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
+ <&dmac1 0xcd>, <&dmac1 0xce>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee140000 0 0x100>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_SDHI1>;
+ dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
+ <&dmac1 0xc1>, <&dmac1 0xc2>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xee160000 0 0x100>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_SDHI2>;
+ dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
+ <&dmac1 0xd3>, <&dmac1 0xd4>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
reg = <0 0xe6b10000 0 0x2c>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7794_CLK_QSPI_MOD>;
- dmas = <&dmac0 0x17>, <&dmac0 0x18>;
- dma-names = "tx", "rx";
+ dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+ <&dmac1 0x17>, <&dmac1 0x18>;
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
/dts-v1/;
-#include "rk3228.dtsi"
+#include "rk322x.dtsi"
/ {
model = "Rockchip RK3228 Evaluation board";
+++ /dev/null
-/*
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/rockchip.h>
-#include <dt-bindings/clock/rk3228-cru.h>
-#include <dt-bindings/thermal/thermal.h>
-#include "skeleton.dtsi"
-
-/ {
- compatible = "rockchip,rk3228";
-
- interrupt-parent = <&gic>;
-
- aliases {
- serial0 = &uart0;
- serial1 = &uart1;
- serial2 = &uart2;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu@f00 {
- device_type = "cpu";
- compatible = "arm,cortex-a7";
- reg = <0xf00>;
- resets = <&cru SRST_CORE0>;
- operating-points = <
- /* KHz uV */
- 816000 1000000
- >;
- #cooling-cells = <2>; /* min followed by max */
- clock-latency = <40000>;
- clocks = <&cru ARMCLK>;
- };
-
- cpu1: cpu@f01 {
- device_type = "cpu";
- compatible = "arm,cortex-a7";
- reg = <0xf01>;
- resets = <&cru SRST_CORE1>;
- };
-
- cpu2: cpu@f02 {
- device_type = "cpu";
- compatible = "arm,cortex-a7";
- reg = <0xf02>;
- resets = <&cru SRST_CORE2>;
- };
-
- cpu3: cpu@f03 {
- device_type = "cpu";
- compatible = "arm,cortex-a7";
- reg = <0xf03>;
- resets = <&cru SRST_CORE3>;
- };
- };
-
- amba {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- pdma: pdma@110f0000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x110f0000 0x4000>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- #dma-cells = <1>;
- clocks = <&cru ACLK_DMAC>;
- clock-names = "apb_pclk";
- };
- };
-
- arm-pmu {
- compatible = "arm,cortex-a7-pmu";
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
- };
-
- timer {
- compatible = "arm,armv7-timer";
- arm,cpu-registers-not-fw-configured;
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- clock-frequency = <24000000>;
- };
-
- xin24m: oscillator {
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "xin24m";
- #clock-cells = <0>;
- };
-
- grf: syscon@11000000 {
- compatible = "syscon";
- reg = <0x11000000 0x1000>;
- };
-
- uart0: serial@11010000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x11010000 0x100>;
- interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <24000000>;
- clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
- clock-names = "baudclk", "apb_pclk";
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
- reg-shift = <2>;
- reg-io-width = <4>;
- status = "disabled";
- };
-
- uart1: serial@11020000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x11020000 0x100>;
- interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <24000000>;
- clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
- clock-names = "baudclk", "apb_pclk";
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_xfer>;
- reg-shift = <2>;
- reg-io-width = <4>;
- status = "disabled";
- };
-
- uart2: serial@11030000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x11030000 0x100>;
- interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <24000000>;
- clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
- clock-names = "baudclk", "apb_pclk";
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_xfer>;
- reg-shift = <2>;
- reg-io-width = <4>;
- status = "disabled";
- };
-
- i2c0: i2c@11050000 {
- compatible = "rockchip,rk3228-i2c";
- reg = <0x11050000 0x1000>;
- interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "i2c";
- clocks = <&cru PCLK_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_xfer>;
- status = "disabled";
- };
-
- i2c1: i2c@11060000 {
- compatible = "rockchip,rk3228-i2c";
- reg = <0x11060000 0x1000>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "i2c";
- clocks = <&cru PCLK_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_xfer>;
- status = "disabled";
- };
-
- i2c2: i2c@11070000 {
- compatible = "rockchip,rk3228-i2c";
- reg = <0x11070000 0x1000>;
- interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "i2c";
- clocks = <&cru PCLK_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_xfer>;
- status = "disabled";
- };
-
- i2c3: i2c@11080000 {
- compatible = "rockchip,rk3228-i2c";
- reg = <0x11080000 0x1000>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "i2c";
- clocks = <&cru PCLK_I2C3>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_xfer>;
- status = "disabled";
- };
-
- pwm0: pwm@110b0000 {
- compatible = "rockchip,rk3288-pwm";
- reg = <0x110b0000 0x10>;
- #pwm-cells = <3>;
- clocks = <&cru PCLK_PWM>;
- clock-names = "pwm";
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pin>;
- status = "disabled";
- };
-
- pwm1: pwm@110b0010 {
- compatible = "rockchip,rk3288-pwm";
- reg = <0x110b0010 0x10>;
- #pwm-cells = <3>;
- clocks = <&cru PCLK_PWM>;
- clock-names = "pwm";
- pinctrl-names = "default";
- pinctrl-0 = <&pwm1_pin>;
- status = "disabled";
- };
-
- pwm2: pwm@110b0020 {
- compatible = "rockchip,rk3288-pwm";
- reg = <0x110b0020 0x10>;
- #pwm-cells = <3>;
- clocks = <&cru PCLK_PWM>;
- clock-names = "pwm";
- pinctrl-names = "default";
- pinctrl-0 = <&pwm2_pin>;
- status = "disabled";
- };
-
- pwm3: pwm@110b0030 {
- compatible = "rockchip,rk3288-pwm";
- reg = <0x110b0030 0x10>;
- #pwm-cells = <2>;
- clocks = <&cru PCLK_PWM>;
- clock-names = "pwm";
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pin>;
- status = "disabled";
- };
-
- timer: timer@110c0000 {
- compatible = "rockchip,rk3288-timer";
- reg = <0x110c0000 0x20>;
- interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&xin24m>, <&cru PCLK_TIMER>;
- clock-names = "timer", "pclk";
- };
-
- cru: clock-controller@110e0000 {
- compatible = "rockchip,rk3228-cru";
- reg = <0x110e0000 0x1000>;
- rockchip,grf = <&grf>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- assigned-clocks = <&cru PLL_GPLL>;
- assigned-clock-rates = <594000000>;
- };
-
- thermal-zones {
- cpu_thermal: cpu-thermal {
- polling-delay-passive = <100>; /* milliseconds */
- polling-delay = <5000>; /* milliseconds */
-
- thermal-sensors = <&tsadc 0>;
-
- trips {
- cpu_alert0: cpu_alert0 {
- temperature = <70000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "passive";
- };
- cpu_alert1: cpu_alert1 {
- temperature = <75000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "passive";
- };
- cpu_crit: cpu_crit {
- temperature = <90000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "critical";
- };
- };
-
- cooling-maps {
- map0 {
- trip = <&cpu_alert0>;
- cooling-device =
- <&cpu0 THERMAL_NO_LIMIT 6>;
- };
- map1 {
- trip = <&cpu_alert1>;
- cooling-device =
- <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
- };
- };
-
- tsadc: tsadc@11150000 {
- compatible = "rockchip,rk3228-tsadc";
- reg = <0x11150000 0x100>;
- interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
- clock-names = "tsadc", "apb_pclk";
- resets = <&cru SRST_TSADC>;
- reset-names = "tsadc-apb";
- pinctrl-names = "init", "default", "sleep";
- pinctrl-0 = <&otp_gpio>;
- pinctrl-1 = <&otp_out>;
- pinctrl-2 = <&otp_gpio>;
- #thermal-sensor-cells = <0>;
- rockchip,hw-tshut-temp = <95000>;
- status = "disabled";
- };
-
- emmc: dwmmc@30020000 {
- compatible = "rockchip,rk3288-dw-mshc";
- reg = <0x30020000 0x4000>;
- interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <37500000>;
- clock-freq-min-max = <400000 37500000>;
- clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
- <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
- clock-names = "biu", "ciu", "ciu_drv", "ciu_sample";
- bus-width = <8>;
- default-sample-phase = <158>;
- num-slots = <1>;
- fifo-depth = <0x100>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
- status = "disabled";
- };
-
- gic: interrupt-controller@32010000 {
- compatible = "arm,gic-400";
- interrupt-controller;
- #interrupt-cells = <3>;
- #address-cells = <0>;
-
- reg = <0x32011000 0x1000>,
- <0x32012000 0x1000>,
- <0x32014000 0x2000>,
- <0x32016000 0x2000>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- pinctrl: pinctrl {
- compatible = "rockchip,rk3228-pinctrl";
- rockchip,grf = <&grf>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- gpio0: gpio0@11110000 {
- compatible = "rockchip,gpio-bank";
- reg = <0x11110000 0x100>;
- interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru PCLK_GPIO0>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio1: gpio1@11120000 {
- compatible = "rockchip,gpio-bank";
- reg = <0x11120000 0x100>;
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru PCLK_GPIO1>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio2: gpio2@11130000 {
- compatible = "rockchip,gpio-bank";
- reg = <0x11130000 0x100>;
- interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru PCLK_GPIO2>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio3: gpio3@11140000 {
- compatible = "rockchip,gpio-bank";
- reg = <0x11140000 0x100>;
- interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru PCLK_GPIO3>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- pcfg_pull_up: pcfg-pull-up {
- bias-pull-up;
- };
-
- pcfg_pull_down: pcfg-pull-down {
- bias-pull-down;
- };
-
- pcfg_pull_none: pcfg-pull-none {
- bias-disable;
- };
-
- emmc {
- emmc_clk: emmc-clk {
- rockchip,pins = <2 7 RK_FUNC_2 &pcfg_pull_none>;
- };
-
- emmc_cmd: emmc-cmd {
- rockchip,pins = <1 22 RK_FUNC_2 &pcfg_pull_none>;
- };
-
- emmc_bus8: emmc-bus8 {
- rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>,
- <1 25 RK_FUNC_2 &pcfg_pull_none>,
- <1 26 RK_FUNC_2 &pcfg_pull_none>,
- <1 27 RK_FUNC_2 &pcfg_pull_none>,
- <1 28 RK_FUNC_2 &pcfg_pull_none>,
- <1 29 RK_FUNC_2 &pcfg_pull_none>,
- <1 30 RK_FUNC_2 &pcfg_pull_none>,
- <1 31 RK_FUNC_2 &pcfg_pull_none>;
- };
- };
-
- i2c0 {
- i2c0_xfer: i2c0-xfer {
- rockchip,pins = <0 0 RK_FUNC_1 &pcfg_pull_none>,
- <0 1 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
-
- i2c1 {
- i2c1_xfer: i2c1-xfer {
- rockchip,pins = <0 2 RK_FUNC_1 &pcfg_pull_none>,
- <0 3 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
-
- i2c2 {
- i2c2_xfer: i2c2-xfer {
- rockchip,pins = <2 20 RK_FUNC_1 &pcfg_pull_none>,
- <2 21 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
-
- i2c3 {
- i2c3_xfer: i2c3-xfer {
- rockchip,pins = <0 6 RK_FUNC_1 &pcfg_pull_none>,
- <0 7 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
-
- pwm0 {
- pwm0_pin: pwm0-pin {
- rockchip,pins = <3 21 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
-
- pwm1 {
- pwm1_pin: pwm1-pin {
- rockchip,pins = <0 30 RK_FUNC_2 &pcfg_pull_none>;
- };
- };
-
- pwm2 {
- pwm2_pin: pwm2-pin {
- rockchip,pins = <1 12 RK_FUNC_2 &pcfg_pull_none>;
- };
- };
-
- pwm3 {
- pwm3_pin: pwm3-pin {
- rockchip,pins = <1 11 RK_FUNC_2 &pcfg_pull_none>;
- };
- };
-
- tsadc {
- otp_gpio: otp-gpio {
- rockchip,pins = <0 24 RK_FUNC_GPIO &pcfg_pull_none>;
- };
-
- otp_out: otp-out {
- rockchip,pins = <0 24 RK_FUNC_2 &pcfg_pull_none>;
- };
- };
-
- uart0 {
- uart0_xfer: uart0-xfer {
- rockchip,pins = <2 26 RK_FUNC_1 &pcfg_pull_none>,
- <2 27 RK_FUNC_1 &pcfg_pull_none>;
- };
-
- uart0_cts: uart0-cts {
- rockchip,pins = <2 29 RK_FUNC_1 &pcfg_pull_none>;
- };
-
- uart0_rts: uart0-rts {
- rockchip,pins = <0 17 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
-
- uart1 {
- uart1_xfer: uart1-xfer {
- rockchip,pins = <1 9 RK_FUNC_1 &pcfg_pull_none>,
- <1 10 RK_FUNC_1 &pcfg_pull_none>;
- };
-
- uart1_cts: uart1-cts {
- rockchip,pins = <1 8 RK_FUNC_1 &pcfg_pull_none>;
- };
-
- uart1_rts: uart1-rts {
- rockchip,pins = <1 11 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
-
- uart2 {
- uart2_xfer: uart2-xfer {
- rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>,
- <1 19 RK_FUNC_2 &pcfg_pull_none>;
- };
-
- uart2_cts: uart2-cts {
- rockchip,pins = <0 25 RK_FUNC_1 &pcfg_pull_none>;
- };
-
- uart2_rts: uart2-rts {
- rockchip,pins = <0 24 RK_FUNC_1 &pcfg_pull_none>;
- };
- };
- };
-};
--- /dev/null
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk322x.dtsi"
+
+/ {
+ model = "Rockchip RK3229 Evaluation board";
+ compatible = "rockchip,rk3229-evb", "rockchip,rk3229";
+
+ memory {
+ device_type = "memory";
+ reg = <0x60000000 0x40000000>;
+ };
+
+ ext_gmac: ext_gmac {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ #clock-cells = <0>;
+ };
+
+ vcc_phy: vcc-phy-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ regulator-name = "vcc_phy";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC_EXTCLK>, <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>, <&cru SCLK_MAC_EXTCLK>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_phy>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ snps,reset-gpio = <&gpio2 24 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/clock/rk3228-cru.h>
+#include <dt-bindings/thermal/thermal.h>
+#include "skeleton.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ resets = <&cru SRST_CORE0>;
+ operating-points = <
+ /* KHz uV */
+ 816000 1000000
+ >;
+ #cooling-cells = <2>; /* min followed by max */
+ clock-latency = <40000>;
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu1: cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ resets = <&cru SRST_CORE1>;
+ };
+
+ cpu2: cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ resets = <&cru SRST_CORE2>;
+ };
+
+ cpu3: cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ resets = <&cru SRST_CORE3>;
+ };
+ };
+
+ amba {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pdma: pdma@110f0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x110f0000 0x4000>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ arm,cpu-registers-not-fw-configured;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ clock-frequency = <24000000>;
+ };
+
+ xin24m: oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xin24m";
+ #clock-cells = <0>;
+ };
+
+ i2s1: i2s1@100b0000 {
+ compatible = "rockchip,rk3228-i2s", "rockchip,rk3066-i2s";
+ reg = <0x100b0000 0x4000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "i2s_clk", "i2s_hclk";
+ clocks = <&cru SCLK_I2S1>, <&cru HCLK_I2S1_8CH>;
+ dmas = <&pdma 14>, <&pdma 15>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1_bus>;
+ status = "disabled";
+ };
+
+ i2s0: i2s0@100c0000 {
+ compatible = "rockchip,rk3228-i2s", "rockchip,rk3066-i2s";
+ reg = <0x100c0000 0x4000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "i2s_clk", "i2s_hclk";
+ clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0_8CH>;
+ dmas = <&pdma 11>, <&pdma 12>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2s2: i2s2@100e0000 {
+ compatible = "rockchip,rk3228-i2s", "rockchip,rk3066-i2s";
+ reg = <0x100e0000 0x4000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "i2s_clk", "i2s_hclk";
+ clocks = <&cru SCLK_I2S2>, <&cru HCLK_I2S2_2CH>;
+ dmas = <&pdma 0>, <&pdma 1>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ grf: syscon@11000000 {
+ compatible = "syscon";
+ reg = <0x11000000 0x1000>;
+ };
+
+ uart0: serial@11010000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x11010000 0x100>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart1: serial@11020000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x11020000 0x100>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart2: serial@11030000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x11030000 0x100>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@11050000 {
+ compatible = "rockchip,rk3228-i2c";
+ reg = <0x11050000 0x1000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@11060000 {
+ compatible = "rockchip,rk3228-i2c";
+ reg = <0x11060000 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_xfer>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@11070000 {
+ compatible = "rockchip,rk3228-i2c";
+ reg = <0x11070000 0x1000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_xfer>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@11080000 {
+ compatible = "rockchip,rk3228-i2c";
+ reg = <0x11080000 0x1000>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "i2c";
+ clocks = <&cru PCLK_I2C3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_xfer>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@110b0000 {
+ compatible = "rockchip,rk3288-pwm";
+ reg = <0x110b0000 0x10>;
+ #pwm-cells = <3>;
+ clocks = <&cru PCLK_PWM>;
+ clock-names = "pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "disabled";
+ };
+
+ pwm1: pwm@110b0010 {
+ compatible = "rockchip,rk3288-pwm";
+ reg = <0x110b0010 0x10>;
+ #pwm-cells = <3>;
+ clocks = <&cru PCLK_PWM>;
+ clock-names = "pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm1_pin>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@110b0020 {
+ compatible = "rockchip,rk3288-pwm";
+ reg = <0x110b0020 0x10>;
+ #pwm-cells = <3>;
+ clocks = <&cru PCLK_PWM>;
+ clock-names = "pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pin>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@110b0030 {
+ compatible = "rockchip,rk3288-pwm";
+ reg = <0x110b0030 0x10>;
+ #pwm-cells = <2>;
+ clocks = <&cru PCLK_PWM>;
+ clock-names = "pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pin>;
+ status = "disabled";
+ };
+
+ timer: timer@110c0000 {
+ compatible = "rockchip,rk3288-timer";
+ reg = <0x110c0000 0x20>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&xin24m>, <&cru PCLK_TIMER>;
+ clock-names = "timer", "pclk";
+ };
+
+ cru: clock-controller@110e0000 {
+ compatible = "rockchip,rk3228-cru";
+ reg = <0x110e0000 0x1000>;
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ assigned-clocks = <&cru PLL_GPLL>;
+ assigned-clock-rates = <594000000>;
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <100>; /* milliseconds */
+ polling-delay = <5000>; /* milliseconds */
+
+ thermal-sensors = <&tsadc 0>;
+
+ trips {
+ cpu_alert0: cpu_alert0 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_alert1: cpu_alert1 {
+ temperature = <75000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_crit: cpu_crit {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT 6>;
+ };
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
+ tsadc: tsadc@11150000 {
+ compatible = "rockchip,rk3228-tsadc";
+ reg = <0x11150000 0x100>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
+ clock-names = "tsadc", "apb_pclk";
+ resets = <&cru SRST_TSADC>;
+ reset-names = "tsadc-apb";
+ pinctrl-names = "init", "default", "sleep";
+ pinctrl-0 = <&otp_gpio>;
+ pinctrl-1 = <&otp_out>;
+ pinctrl-2 = <&otp_gpio>;
+ #thermal-sensor-cells = <0>;
+ rockchip,hw-tshut-temp = <95000>;
+ status = "disabled";
+ };
+
+ emmc: dwmmc@30020000 {
+ compatible = "rockchip,rk3288-dw-mshc";
+ reg = <0x30020000 0x4000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <37500000>;
+ clock-freq-min-max = <400000 37500000>;
+ clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu_drv", "ciu_sample";
+ bus-width = <8>;
+ default-sample-phase = <158>;
+ num-slots = <1>;
+ fifo-depth = <0x100>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "disabled";
+ };
+
+ gmac: ethernet@30200000 {
+ compatible = "rockchip,rk3228-gmac";
+ reg = <0x30200000 0x10000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&cru SCLK_MAC>, <&cru SCLK_MAC_RX>,
+ <&cru SCLK_MAC_TX>, <&cru SCLK_MAC_REF>,
+ <&cru SCLK_MAC_REFOUT>, <&cru ACLK_GMAC>,
+ <&cru PCLK_GMAC>;
+ clock-names = "stmmaceth", "mac_clk_rx",
+ "mac_clk_tx", "clk_mac_ref",
+ "clk_mac_refout", "aclk_mac",
+ "pclk_mac";
+ resets = <&cru SRST_GMAC>;
+ reset-names = "stmmaceth";
+ rockchip,grf = <&grf>;
+ status = "disabled";
+ };
+
+ gic: interrupt-controller@32010000 {
+ compatible = "arm,gic-400";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+
+ reg = <0x32011000 0x1000>,
+ <0x32012000 0x1000>,
+ <0x32014000 0x2000>,
+ <0x32016000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ pinctrl: pinctrl {
+ compatible = "rockchip,rk3228-pinctrl";
+ rockchip,grf = <&grf>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio0: gpio0@11110000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x11110000 0x100>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio1@11120000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x11120000 0x100>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO1>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio2@11130000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x11130000 0x100>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO2>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio3@11140000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0x11140000 0x100>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO3>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pcfg_pull_up: pcfg-pull-up {
+ bias-pull-up;
+ };
+
+ pcfg_pull_down: pcfg-pull-down {
+ bias-pull-down;
+ };
+
+ pcfg_pull_none: pcfg-pull-none {
+ bias-disable;
+ };
+
+ pcfg_pull_none_drv_12ma: pcfg-pull-none-drv-12ma {
+ drive-strength = <12>;
+ };
+
+ emmc {
+ emmc_clk: emmc-clk {
+ rockchip,pins = <2 7 RK_FUNC_2 &pcfg_pull_none>;
+ };
+
+ emmc_cmd: emmc-cmd {
+ rockchip,pins = <1 22 RK_FUNC_2 &pcfg_pull_none>;
+ };
+
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>,
+ <1 25 RK_FUNC_2 &pcfg_pull_none>,
+ <1 26 RK_FUNC_2 &pcfg_pull_none>,
+ <1 27 RK_FUNC_2 &pcfg_pull_none>,
+ <1 28 RK_FUNC_2 &pcfg_pull_none>,
+ <1 29 RK_FUNC_2 &pcfg_pull_none>,
+ <1 30 RK_FUNC_2 &pcfg_pull_none>,
+ <1 31 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
+ gmac {
+ rgmii_pins: rgmii-pins {
+ rockchip,pins = <2 14 RK_FUNC_1 &pcfg_pull_none>,
+ <2 12 RK_FUNC_1 &pcfg_pull_none>,
+ <2 25 RK_FUNC_1 &pcfg_pull_none>,
+ <2 19 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 18 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 22 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 23 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 9 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 13 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 17 RK_FUNC_1 &pcfg_pull_none>,
+ <2 16 RK_FUNC_1 &pcfg_pull_none>,
+ <2 21 RK_FUNC_2 &pcfg_pull_none>,
+ <2 20 RK_FUNC_2 &pcfg_pull_none>,
+ <2 11 RK_FUNC_1 &pcfg_pull_none>,
+ <2 8 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ rmii_pins: rmii-pins {
+ rockchip,pins = <2 14 RK_FUNC_1 &pcfg_pull_none>,
+ <2 12 RK_FUNC_1 &pcfg_pull_none>,
+ <2 25 RK_FUNC_1 &pcfg_pull_none>,
+ <2 19 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 18 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 13 RK_FUNC_1 &pcfg_pull_none_drv_12ma>,
+ <2 17 RK_FUNC_1 &pcfg_pull_none>,
+ <2 16 RK_FUNC_1 &pcfg_pull_none>,
+ <2 8 RK_FUNC_1 &pcfg_pull_none>,
+ <2 15 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ phy_pins: phy-pins {
+ rockchip,pins = <2 14 RK_FUNC_2 &pcfg_pull_none>,
+ <2 8 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
+ i2c0 {
+ i2c0_xfer: i2c0-xfer {
+ rockchip,pins = <0 0 RK_FUNC_1 &pcfg_pull_none>,
+ <0 1 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c1 {
+ i2c1_xfer: i2c1-xfer {
+ rockchip,pins = <0 2 RK_FUNC_1 &pcfg_pull_none>,
+ <0 3 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c2 {
+ i2c2_xfer: i2c2-xfer {
+ rockchip,pins = <2 20 RK_FUNC_1 &pcfg_pull_none>,
+ <2 21 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ i2c3 {
+ i2c3_xfer: i2c3-xfer {
+ rockchip,pins = <0 6 RK_FUNC_1 &pcfg_pull_none>,
+ <0 7 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ i2s1 {
+ i2s1_bus: i2s1-bus {
+ rockchip,pins = <0 8 RK_FUNC_1 &pcfg_pull_none>,
+ <0 9 RK_FUNC_1 &pcfg_pull_none>,
+ <0 11 RK_FUNC_1 &pcfg_pull_none>,
+ <0 12 RK_FUNC_1 &pcfg_pull_none>,
+ <0 13 RK_FUNC_1 &pcfg_pull_none>,
+ <0 14 RK_FUNC_1 &pcfg_pull_none>,
+ <1 2 RK_FUNC_1 &pcfg_pull_none>,
+ <1 4 RK_FUNC_1 &pcfg_pull_none>,
+ <1 5 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm0 {
+ pwm0_pin: pwm0-pin {
+ rockchip,pins = <3 21 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ pwm1 {
+ pwm1_pin: pwm1-pin {
+ rockchip,pins = <0 30 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
+ pwm2 {
+ pwm2_pin: pwm2-pin {
+ rockchip,pins = <1 12 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
+ pwm3 {
+ pwm3_pin: pwm3-pin {
+ rockchip,pins = <1 11 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
+ tsadc {
+ otp_gpio: otp-gpio {
+ rockchip,pins = <0 24 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ otp_out: otp-out {
+ rockchip,pins = <0 24 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
+ uart0 {
+ uart0_xfer: uart0-xfer {
+ rockchip,pins = <2 26 RK_FUNC_1 &pcfg_pull_none>,
+ <2 27 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ uart0_cts: uart0-cts {
+ rockchip,pins = <2 29 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ uart0_rts: uart0-rts {
+ rockchip,pins = <0 17 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ uart1 {
+ uart1_xfer: uart1-xfer {
+ rockchip,pins = <1 9 RK_FUNC_1 &pcfg_pull_none>,
+ <1 10 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ uart1_cts: uart1-cts {
+ rockchip,pins = <1 8 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ uart1_rts: uart1-rts {
+ rockchip,pins = <1 11 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
+ uart2 {
+ uart2_xfer: uart2-xfer {
+ rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>,
+ <1 19 RK_FUNC_2 &pcfg_pull_none>;
+ };
+
+ uart2_cts: uart2-cts {
+ rockchip,pins = <0 25 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ uart2_rts: uart2-rts {
+ rockchip,pins = <0 24 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+ };
+};
clock-output-names = "ext_gmac";
};
- io_domains: io-domains {
- compatible = "rockchip,rk3288-io-voltage-domain";
- rockchip,grf = <&grf>;
-
- audio-supply = <&vcca_33>;
- bb-supply = <&vcc_io>;
- dvp-supply = <&dovdd_1v8>;
- flash0-supply = <&vcc_flash>;
- flash1-supply = <&vcc_lan>;
- gpio30-supply = <&vcc_io>;
- gpio1830-supply = <&vcc_io>;
- lcdc-supply = <&vcc_io>;
- sdcard-supply = <&vccio_sd>;
- wifi-supply = <&vccio_wl>;
- };
-
ir: ir-receiver {
compatible = "gpio-ir-receiver";
pinctrl-names = "default";
status = "okay";
};
+&io_domains {
+ status = "okay";
+
+ audio-supply = <&vcca_33>;
+ bb-supply = <&vcc_io>;
+ dvp-supply = <&dovdd_1v8>;
+ flash0-supply = <&vcc_flash>;
+ flash1-supply = <&vcc_lan>;
+ gpio30-supply = <&vcc_io>;
+ gpio1830-supply = <&vcc_io>;
+ lcdc-supply = <&vcc_io>;
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vccio_wl>;
+};
+
&pinctrl {
pcfg_output_high: pcfg-output-high {
output-high;
clock-output-names = "ext_gmac";
};
- io_domains: io-domains {
- compatible = "rockchip,rk3288-io-voltage-domain";
-
- audio-supply = <&vcca_33>;
- flash0-supply = <&vcc_flash>;
- flash1-supply = <&vcc_lan>;
- gpio30-supply = <&vcc_io>;
- gpio1830-supply = <&vcc_io>;
- lcdc-supply = <&vcc_io>;
- sdcard-supply = <&vccio_sd>;
- wifi-supply = <&vcc_18>;
- };
-
leds {
compatible = "gpio-leds";
status = "okay";
};
+&io_domains {
+ status = "okay";
+
+ audio-supply = <&vcca_33>;
+ flash0-supply = <&vcc_flash>;
+ flash1-supply = <&vcc_lan>;
+ gpio30-supply = <&vcc_io>;
+ gpio1830-supply = <&vcc_io>;
+ lcdc-supply = <&vcc_io>;
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vcc_18>;
+};
+
&pinctrl {
pcfg_output_high: pcfg-output-high {
output-high;
};
};
- io_domains: io-domains {
- compatible = "rockchip,rk3288-io-voltage-domain";
- rockchip,grf = <&grf>;
-
- audio-supply = <&vcca_33>;
- bb-supply = <&vcc_io>;
- dvp-supply = <&vcc18_dvp>;
- flash0-supply = <&vcc_flash>;
- flash1-supply = <&vcc_lan>;
- gpio30-supply = <&vcc_io>;
- gpio1830-supply = <&vcc_io>;
- lcdc-supply = <&vcc_io>;
- sdcard-supply = <&vccio_sd>;
- wifi-supply = <&vccio_wl>;
- };
-
ir: ir-receiver {
compatible = "gpio-ir-receiver";
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
+&io_domains {
+ status = "okay";
+
+ audio-supply = <&vcca_33>;
+ bb-supply = <&vcc_io>;
+ dvp-supply = <&vcc18_dvp>;
+ flash0-supply = <&vcc_flash>;
+ flash1-supply = <&vcc_lan>;
+ gpio30-supply = <&vcc_io>;
+ gpio1830-supply = <&vcc_io>;
+ lcdc-supply = <&vcc_io>;
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vccio_wl>;
+};
+
&pinctrl {
ak8963 {
comp_int: comp-int {
clock-output-names = "ext_gmac";
};
- io_domains: io-domains {
- compatible = "rockchip,rk3288-io-voltage-domain";
- rockchip,grf = <&grf>;
-
- audio-supply = <&vcc_io>;
- bb-supply = <&vcc_io>;
- dvp-supply = <&vcc_18>;
- flash0-supply = <&vcc_flash>;
- flash1-supply = <&vccio_pmu>;
- gpio30-supply = <&vccio_pmu>;
- gpio1830 = <&vcc_io>;
- lcdc-supply = <&vcc_io>;
- sdcard-supply = <&vccio_sd>;
- wifi-supply = <&vcc_18>;
- };
-
vcc_flash: flash-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
};
};
+&io_domains {
+ status = "okay";
+
+ audio-supply = <&vcc_io>;
+ bb-supply = <&vcc_io>;
+ dvp-supply = <&vcc_18>;
+ flash0-supply = <&vcc_flash>;
+ flash1-supply = <&vccio_pmu>;
+ gpio30-supply = <&vccio_pmu>;
+ gpio1830 = <&vcc_io>;
+ lcdc-supply = <&vcc_io>;
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vcc_18>;
+};
+
&pinctrl {
pcfg_output_high: pcfg-output-high {
output-high;
--- /dev/null
+/*
+ * Google Veyron (and derivatives) fragment for the max98090 audio
+ * codec and analog headphone jack.
+ *
+ * Copyright 2016 Google, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+ sound {
+ compatible = "rockchip,rockchip-audio-max98090";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mic_det>, <&hp_det>;
+ rockchip,model = "VEYRON-I2S";
+ rockchip,i2s-controller = <&i2s>;
+ rockchip,audio-codec = <&max98090>;
+ rockchip,hp-det-gpios = <&gpio6 5 GPIO_ACTIVE_HIGH>;
+ rockchip,mic-det-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+ rockchip,headset-codec = <&headsetcodec>;
+ };
+};
+
+&i2c2 {
+ max98090: max98090@10 {
+ compatible = "maxim,max98090";
+ reg = <0x10>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ clock-names = "mclk";
+ clocks = <&cru SCLK_I2S0_OUT>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&int_codec>;
+ };
+};
+
+&i2c4 {
+ headsetcodec: ts3a227e@3b {
+ compatible = "ti,ts3a227e";
+ reg = <0x3b>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts3a227e_int_l>;
+ ti,micbias = <7>; /* MICBIAS = 2.8V */
+ };
+};
+
+&i2s {
+ status = "okay";
+};
+
+&io_domains {
+ audio-supply = <&vcc18_codec>;
+};
+
+&rk808 {
+ vcc10-supply = <&vcc33_sys>;
+
+ regulators {
+ vcc18_codec: LDO_REG6 {
+ regulator-name = "vcc18_codec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ codec {
+ hp_det: hp-det {
+ rockchip,pins = <6 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ /*
+ * HACK: We're going to _pull down_ this _active low_ interrupt
+ * so that it never fires. We don't need this interrupt because
+ * we've got a ts3a227e chip but the driver requires it.
+ */
+ int_codec: int-codec {
+ rockchip,pins = <6 7 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ mic_det: mic-det {
+ rockchip,pins = <6 11 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ headset {
+ ts3a227e_int_l: ts3a227e-int-l {
+ rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
#include <dt-bindings/clock/rockchip,rk808.h>
#include <dt-bindings/input/input.h>
#include "rk3288-veyron.dtsi"
+#include "rk3288-veyron-analog-audio.dtsi"
#include "rk3288-veyron-sdmmc.dtsi"
/ {
reset-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>;
};
- io_domains: io-domains {
- compatible = "rockchip,rk3288-io-voltage-domain";
- rockchip,grf = <&grf>;
-
- bb-supply = <&vcc33_io>;
- dvp-supply = <&vcc_18>;
- flash0-supply = <&vcc18_flashio>;
- gpio1830-supply = <&vcc33_io>;
- gpio30-supply = <&vcc33_io>;
- lcdc-supply = <&vcc33_lcd>;
- wifi-supply = <&vcc18_wl>;
- };
-
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rk808 RK808_CLKOUT1>;
i2c-scl-rising-time-ns = <1000>;
};
+&io_domains {
+ status = "okay";
+
+ bb-supply = <&vcc33_io>;
+ dvp-supply = <&vcc_18>;
+ flash0-supply = <&vcc18_flashio>;
+ gpio1830-supply = <&vcc33_io>;
+ gpio30-supply = <&vcc33_io>;
+ lcdc-supply = <&vcc33_lcd>;
+ wifi-supply = <&vcc18_wl>;
+};
+
&pwm1 {
status = "okay";
};
status = "okay";
rx-sample-delay-ns = <12>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
};
&tsadc {
#phy-cells = <0>;
status = "disabled";
};
+
+ io_domains: io-domains {
+ compatible = "rockchip,rk3288-io-voltage-domain";
+ status = "disabled";
+ };
};
wdt: watchdog@ff800000 {
};
};
+ pmu {
+ compatible = "arm,cortex-a5-pmu";
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 0>;
+ };
+
memory {
reg = <0x20000000 0x20000000>;
};
clock-names = "pclk", "hclk";
status = "disabled";
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep7 {
+ ep@7 {
reg = <7>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep8 {
+ ep@8 {
reg = <8>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep9 {
+ ep@9 {
reg = <9>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep10 {
+ ep@10 {
reg = <10>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep11 {
+ ep@11 {
reg = <11>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep12 {
+ ep@12 {
reg = <12>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep13 {
+ ep@13 {
reg = <13>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep14 {
+ ep@14 {
reg = <14>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep15 {
+ ep@15 {
reg = <15>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,adc-res-names = "lowres", "highres";
status = "disabled";
- trigger@0 {
- reg = <0>;
+ trigger0 {
trigger-name = "external-rising";
trigger-value = <0x1>;
trigger-external;
};
- trigger@1 {
- reg = <1>;
+ trigger1 {
trigger-name = "external-falling";
trigger-value = <0x2>;
trigger-external;
};
- trigger@2 {
- reg = <2>;
+ trigger2 {
trigger-name = "external-any";
trigger-value = <0x3>;
trigger-external;
};
- trigger@3 {
- reg = <3>;
+ trigger3 {
trigger-name = "continuous";
trigger-value = <0x6>;
};
clock-names = "pclk", "hclk";
status = "disabled";
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-dma;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-dma;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-dma;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-dma;
};
- ep7 {
+ ep@7 {
reg = <7>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-dma;
};
- ep8 {
+ ep@8 {
reg = <8>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
};
- ep9 {
+ ep@9 {
reg = <9>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
};
- ep10 {
+ ep@10 {
reg = <10>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
};
- ep11 {
+ ep@11 {
reg = <11>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
};
- ep12 {
+ ep@12 {
reg = <12>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
};
- ep13 {
+ ep@13 {
reg = <13>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
};
- ep14 {
+ ep@14 {
reg = <14>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
};
- ep15 {
+ ep@15 {
reg = <15>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
/dts-v1/;
#include "sama5d31.dtsi"
#include "sama5d3xmb.dtsi"
+#include "sama5d3xmb_emac.dtsi"
#include "sama5d3xdm.dtsi"
/ {
/dts-v1/;
#include "sama5d33.dtsi"
#include "sama5d3xmb.dtsi"
+#include "sama5d3xmb_gmac.dtsi"
#include "sama5d3xdm.dtsi"
/ {
/dts-v1/;
#include "sama5d34.dtsi"
#include "sama5d3xmb.dtsi"
+#include "sama5d3xmb_gmac.dtsi"
#include "sama5d3xdm.dtsi"
/ {
/dts-v1/;
#include "sama5d35.dtsi"
#include "sama5d3xmb.dtsi"
+#include "sama5d3xmb_emac.dtsi"
+#include "sama5d3xmb_gmac.dtsi"
/ {
model = "Atmel SAMA5D35-EK";
#include "sama5d36.dtsi"
#include "sama5d3xmb.dtsi"
#include "sama5d3xdm.dtsi"
+#include "sama5d3xmb_emac.dtsi"
+#include "sama5d3xmb_gmac.dtsi"
/ {
model = "Atmel SAMA5D36-EK";
spi0: spi@f0004000 {
cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
};
-
- macb0: ethernet@f0028000 {
- phy-mode = "rgmii";
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethernet-phy@1 {
- reg = <0x1>;
- interrupt-parent = <&pioB>;
- interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
- txen-skew-ps = <800>;
- txc-skew-ps = <3000>;
- rxdv-skew-ps = <400>;
- rxc-skew-ps = <3000>;
- rxd0-skew-ps = <400>;
- rxd1-skew-ps = <400>;
- rxd2-skew-ps = <400>;
- rxd3-skew-ps = <400>;
- };
-
- ethernet-phy@7 {
- reg = <0x7>;
- interrupt-parent = <&pioB>;
- interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
- txen-skew-ps = <800>;
- txc-skew-ps = <3000>;
- rxdv-skew-ps = <400>;
- rxc-skew-ps = <3000>;
- rxd0-skew-ps = <400>;
- rxd1-skew-ps = <400>;
- rxd2-skew-ps = <400>;
- rxd3-skew-ps = <400>;
- };
- };
};
nand0: nand@60000000 {
status = "okay";
};
- macb1: ethernet@f802c000 {
- phy-mode = "rmii";
-
- #address-cells = <1>;
- #size-cells = <0>;
- phy0: ethernet-phy@1 {
- interrupt-parent = <&pioE>;
- interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
- reg = <1>;
- };
- };
-
pinctrl@fffff200 {
board {
pinctrl_mmc0_cd: mmc0_cd {
--- /dev/null
+/*
+ * sama5d3xmb_emac.dts - Device Tree Include file for SAMA5D3x mother board
+ * Ethernet
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ ahb {
+ apb {
+ macb1: ethernet@f802c000 {
+ phy-mode = "rmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@1 {
+ interrupt-parent = <&pioE>;
+ interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+ reg = <1>;
+ };
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * sama5d3xmb_gmac.dtsi - Device Tree Include file for SAMA5D3x motherboard
+ * Gigabit Ethernet
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ ahb {
+ apb {
+ macb0: ethernet@f0028000 {
+ phy-mode = "rgmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+
+ ethernet-phy@7 {
+ reg = <0x7>;
+ interrupt-parent = <&pioB>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ txen-skew-ps = <800>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <400>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <400>;
+ rxd1-skew-ps = <400>;
+ rxd2-skew-ps = <400>;
+ rxd3-skew-ps = <400>;
+ };
+ };
+ };
+ };
+};
clock-names = "pclk", "hclk";
status = "disabled";
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep7 {
+ ep@7 {
reg = <7>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep8 {
+ ep@8 {
reg = <8>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep9 {
+ ep@9 {
reg = <9>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep10 {
+ ep@10 {
reg = <10>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep11 {
+ ep@11 {
reg = <11>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep12 {
+ ep@12 {
reg = <12>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep13 {
+ ep@13 {
reg = <13>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep14 {
+ ep@14 {
reg = <14>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,can-isoc;
};
- ep15 {
+ ep@15 {
reg = <15>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
atmel,adc-ts-pressure-threshold = <10000>;
status = "disabled";
- trigger@0 {
+ trigger0 {
trigger-name = "external-rising";
trigger-value = <0x1>;
trigger-external;
};
- trigger@1 {
+ trigger1 {
trigger-name = "external-falling";
trigger-value = <0x2>;
trigger-external;
};
- trigger@2 {
+ trigger2 {
trigger-name = "external-any";
trigger-value = <0x3>;
trigger-external;
};
- trigger@3 {
+ trigger3 {
trigger-name = "continuous";
trigger-value = <0x6>;
};
compatible = "renesas,kzm9g", "renesas,sh73a0";
aliases {
- serial4 = &scifa4;
+ serial0 = &scifa4;
};
cpus {
};
chosen {
- bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel rw";
- stdout-path = &scifa4;
+ bootargs = "root=/dev/nfs ip=dhcp ignore_loglevel rw";
+ stdout-path = "serial0:115200n8";
};
- memory {
+ memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x20000000>;
};
- reg_1p8v: regulator@0 {
+ reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-boot-on;
};
- reg_3p3v: regulator@1 {
+ reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-boot-on;
};
- vmmc_sdhi0: regulator@2 {
+ vmmc_sdhi0: regulator-vmmc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
regulator-min-microvolt = <3300000>;
enable-active-high;
};
- vmmc_sdhi2: regulator@3 {
+ vmmc_sdhi2: regulator-vmmc-sdhi2 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
regulator-min-microvolt = <3300000>;
};
};
- scifa4_pins: serial4 {
+ scifa4_pins: scifa4 {
groups = "scifa4_data", "scifa4_ctrl";
function = "scifa4";
};
pinctrl-0 = <&scifa4_pins>;
pinctrl-names = "default";
+ uart-has-rtscts;
status = "okay";
};
<0xf0000100 0x100>;
};
- L2: cache-controller {
+ L2: cache-controller@f0100000 {
compatible = "arm,pl310-cache";
reg = <0xf0100000 0x1000>;
interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <1>;
- aliases {
- serial0 = &uart0;
- serial1 = &uart1;
- };
-
cpus {
#address-cells = <1>;
#size-cells = <0>;
reg = <0xffcfb100 0x80>;
};
- sdramedac {
- compatible = "altr,sdram-edac-a10";
- altr,sdr-syscon = <&sdr>;
- interrupts = <0 2 4>, <0 0 4>;
- };
-
L2: l2-cache@fffff000 {
compatible = "arm,pl310-cache";
reg = <0xfffff000 0x1000>;
#size-cells = <1>;
interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>,
<0 0 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
ranges;
+ sdramedac {
+ compatible = "altr,sdram-edac-a10";
+ altr,sdr-syscon = <&sdr>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+ <49 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
l2-ecc@ffd06010 {
compatible = "altr,socfpga-a10-l2-ecc";
reg = <0xffd06010 0x4>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>,
+ <32 IRQ_TYPE_LEVEL_HIGH>;
};
ocram-ecc@ff8c3000 {
compatible = "altr,socfpga-a10-ocram-ecc";
reg = <0xff8c3000 0x400>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>,
+ <33 IRQ_TYPE_LEVEL_HIGH>;
};
emac0-rx-ecc@ff8c0800 {
model = "Altera SOCFPGA Arria 10";
compatible = "altr,socfpga-arria10", "altr,socfpga";
+ aliases {
+ ethernet0 = &gmac0;
+ serial0 = &uart1;
+ };
+
chosen {
bootargs = "earlyprintk";
- stdout-path = "serial1:115200n8";
+ stdout-path = "serial0:115200n8";
};
memory {
#interrupt-cells = <2>;
ab8500_gpio: ab8500-gpio {
+ compatible = "stericsson,ab8500-gpio";
gpio-controller;
#gpio-cells = <2>;
};
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
- interrupt-parent = <&gpio2>;
- interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
- <19 IRQ_TYPE_EDGE_FALLING>;
- };
- lsm303dlh@1e {
/*
- * This magnetometer is packaged with
- * the accelerometer, and has a DRDY line,
- * however it is not connected on this
- * board so it can not generate interrupts.
+ * These interrupts cannot be used: the other component
+ * ST-Micro L3D4200D gyro that is connected to the same lines
+ * cannot set its DRDY line to open drain, so it cannot be
+ * shared with other peripherals. The should be defined for
+ * the falling edge if they could be wired together.
+ *
+ * interrupts-extended =
+ * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+ * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
*/
+ };
+ lsm303dlh@1e {
+ /* Magnetometer */
compatible = "st,lsm303dlh-magn";
reg = <0x1e>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
+ /*
+ * These interrupts cannot be used: the other component
+ * ST-Micro L3D4200D gyro that is connected to the same lines
+ * cannot set its DRDY line to open drain, so it cannot be
+ * shared with other peripherals. The should be defined for
+ * the falling edge if they could be wired together.
+ *
+ * interrupts-extended =
+ * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+ * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
+ */
};
lis331dl@1c {
/* Accelerometer */
compatible = "st,lis331dl-accel";
st,drdy-int-pin = <1>;
- drive-open-drain;
reg = <0x1c>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
interrupt-parent = <&gpio2>;
- interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
- <19 IRQ_TYPE_EDGE_FALLING>;
+ /* INT2 would need to be open drain */
+ interrupts = <18 IRQ_TYPE_EDGE_RISING>,
+ <19 IRQ_TYPE_EDGE_RISING>;
};
ak8974@0f {
/* Magnetometer */
compatible = "asahi-kasei,ak8974";
reg = <0x0f>;
- vdd-supply = <&ab8500_ldo_aux1_reg>;
- vddio-supply = <&db8500_vsmps2_reg>;
+ avdd-supply = <&ab8500_ldo_aux1_reg>;
+ dvdd-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&gyro_magn_tvk_mode>;
- interrupt-parent = <&gpio1>;
- interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+ /*
+ * These interrupts cannot be used: the other component
+ * ST-Micro L3D4200D gyro that is connected to the same lines
+ * cannot set its DRDY line to open drain, so it cannot be
+ * shared with other peripherals. The should be defined for
+ * the falling edge if they could be wired together.
+ *
+ * interrupts-extended =
+ * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+ * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
+ */
};
l3g4200d@68 {
/* Gyroscope */
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&gyro_magn_tvk_mode>;
- interrupt-parent = <&gpio1>;
- interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+ interrupts-extended =
+ <&gpio1 0 IRQ_TYPE_EDGE_RISING>,
+ <&gpio0 31 IRQ_TYPE_EDGE_RISING>;
};
lsp001wm@5c {
/* Barometer/pressure sensor */
/* Accelerometer interrupt lines 1 & 2 */
tvk_cfg {
pins = "GPIO82_C1", "GPIO83_D3";
- ste,config = <&gpio_in_pu>;
+ ste,config = <&gpio_in_pd>;
};
};
};
prcmu@80157000 {
ab8500 {
ab8500-gpio {
- compatible = "stericsson,ab8500-gpio";
};
ab8500-regulators {
compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
soc {
+ /* Name the GPIO muxed rails on the HREF boards */
+ gpio@8012e000 {
+ /* GPIOs 0 - 31 */
+ gpio-line-names =
+ /* GPIO0,1 used for UART0 BT RX/TX */
+ "", "",
+ "UART_WAKE",
+ "BT_WAKE",
+ "",
+ "SDMMC_1V8_3V_SEL",
+ "FLASH_LED_SYNC (FLASH_CTRL_0)",
+ "XENON_READY (FLASH_CTRL_1)",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "",
+ "",
+ "FLASH_LED_EN (FLASH_CTRL_3)",
+ "", "",
+ "", "", "", "", "",
+ /* Used by UART2 (console) */
+ "", "",
+ "MAGNETOMETER_INT";
+ };
+
+ gpio@8012e080 {
+ /* GPIOs 32 - 63 */
+ gpio-line-names =
+ "MAGNETOMETER_DRDY",
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e000 {
+ /* GPIOs 64 - 95 */
+ gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
+ "DISP1_RST",
+ "DISP2_RST",
+ "TOUCH_INT2",
+ "LCD_VSI0_A",
+ "LCD_VSI1_A",
+ /* GPIO 70-77 used for ETM */
+ "", "", "", "", "", "", "", "",
+ /* GPIO 78-81 used for YCBCR */
+ "", "", "", "",
+ "ACCELEROMETER_INT1_RDY",
+ "ACCELEROMETER_INT2",
+ "TOUCH_INT",
+ "WLAN_ENA",
+ "", "", "", "", "",
+ "FORCE_SENSING_INT",
+ "FORCE_SENSING_RESET",
+ "", "",
+ "SDMMC_CD";
+ };
+
+ gpio@8000e080 {
+ /* GPIOs 96 - 127 */
+ gpio-line-names = "",
+ "FORCE_SENSING_WU",
+ "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e100 {
+ /* GPIOs 128 - 159 */
+ gpio-line-names = "", "", "", "", "", "", "", "",
+ "", "", "",
+ "DIPRO_INT", /* GPIO139 */
+ "XSHUTDOWN_SECONDARY_SENSOR",
+ "XSHUTDOWN_PRIMARY_SENSOR",
+ "NFC_RST (NFC_CTRL_",
+ "TOUCH_RST",
+ "NFC_IRQ (NFC_CTRL_1)",
+ "HAL_SW",
+ "TOUCH_RST2",
+ "", "",
+ "VAUDIO_HF_EN", /* GPIO149 */
+ "", "", "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e180 {
+ /* GPIOs 160 - 191 */
+ gpio-line-names = "", "", "", "", "", "", "", "",
+ "",
+ "SDMMC_EN",
+ "XENON_CHARGE (FLASH_CONTROL_5)",
+ "GBF_ENA_RESET",
+ "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8011e000 {
+ /* GPIOs 192 - 223 */
+ gpio-line-names = "HDTV_INTN",
+ "", "", "",
+ "HDTV_RSTN",
+ "", "", "",
+ "", /* GPIO200 */
+ "", "", "", "", "", "", "",
+ /* GPIO208-216 used for WGBF_MC1 */
+ "", "", "", "", "", "", "", "", "",
+ "SW_FRONT_PROXIMITY", /* GPIO217 */
+ "KPD_CTRL_INT", /* Keypad controller */
+ "", "", "", "", "";
+ };
+
+ gpio@8011e080 {
+ /* GPIOs 224 - 255 */
+ gpio-line-names = "", "",
+ "HSIT_ACWAKE0",
+ "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
// External Micro SD slot
sdi0_per1@80126000 {
cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
};
soc {
+ /* Name the GPIO muxed rails on the Snowball board */
+ gpio@8012e000 {
+ /* GPIOs 0 - 31 */
+ gpio-line-names = "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "",
+ "AP_GPIO31";
+ };
+
+ gpio@8012e080 {
+ /* GPIOs 32 - 63 */
+ gpio-line-names = "USR PB", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e000 {
+ /* GPIOs 64 - 95 */
+ gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e100 {
+ /* GPIOs 128 - 159 */
+ gpio-line-names = "", "", "", "", "", "", "", "",
+ "", "", "", "", "IRQ_LAN", "RSTn_LAN",
+ "USR_LED", "", "", "", "", "", "",
+ "", "", "AP_GPIO151", "AP_GPIO152",
+ "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e180 {
+ /* GPIOs 160 - 191 */
+ gpio-line-names = "", "AP_GPIO161", "AP_GPIO162",
+ "ACCELEROMETER_INT1_RDY",
+ "ACCELEROMETER_INT2", "MAG_DRDY",
+ "GYRO_DRDY", "RSTn_MLC", "RSTn_SLC",
+ "GYRO_INT", "UART_WAKE", "GBF_RESET",
+ "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8011e000 {
+ /* GPIOs 192 - 223 */
+ gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST",
+ "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "",
+ "WLAN_RESETN", "WLAN_IRQ", "MMC_EN",
+ "MMC_CD", "", "", "", "", "";
+ };
+
+ gpio@8011e080 {
+ /* GPIOs 224 - 255 */
+ gpio-line-names = "", "", "", "", "SD_SEL", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
usb_per5@a03e0000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&musb_default_mode>;
ab8500 {
ab8500-gpio {
- compatible = "stericsson,ab8500-gpio";
+ /*
+ * AB8500 GPIOs are numbered starting from 1, so the first
+ * index 0 is what in the datasheet is called "GPIO1", and
+ * the second is "GPIO2" and so forth. Confusingly, the
+ * Snowball schematic then names the "GPIO2" line "PM_GPIO1".
+ * while later naming "GPIO4" as "PM_GPIO4".
+ */
+ gpio-line-names = "", /* AB8500 GPIO1 */
+ "PM_GPIO1", /* AB8500 GPIO2 */
+ "WLAN_CLK_REQ", /* AB8500 GPIO3 */
+ "PM_GPIO4", /* AB8500 GPIO4 */
+ "", "", "", "", "", "", "", "", "", "", "",
+ "EN_3V6", /* AB8500 GPIO16 */
+ "", "", "", "" ,"", "", "", "", "",
+ "EN_3V3", /* AB8500 GPIO26 */
+ "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "PM_GPIO40", /* AB8500 GPIO40 */
+ "PM_GPIO41", /* AB8500 GPIO41 */
+ "PM_GPIO42"; /* AB8500 GPIO42 */
};
ext_regulators: ab8500-ext-regulators {
clocks = <&clk_sysin>;
clock-output-names = "clk-s-a0-pll-ofd-0";
+ clock-critical = <0>; /* clk-s-a0-pll-ofd-0 */
};
clk_s_a0_flexgen: clk-s-a0-flexgen {
clock-output-names = "clk-ic-lmi0",
"clk-ic-lmi1";
+ clock-critical = <CLK_IC_LMI0>;
};
};
"clk-s-c0-fs0-ch1",
"clk-s-c0-fs0-ch2",
"clk-s-c0-fs0-ch3";
+ clock-critical = <0>; /* clk-s-c0-fs0-ch0 */
};
clk_s_c0: clockgen-c@09103000 {
clocks = <&clk_sysin>;
clock-output-names = "clk-s-c0-pll0-odf-0";
+ clock-critical = <0>; /* clk-s-c0-pll0-odf-0 */
};
clk_s_c0_pll1: clk-s-c0-pll1 {
"clk-clust-hades",
"clk-hwpe-hades",
"clk-fc-hades";
+ clock-critical = <CLK_ICN_CPU>,
+ <CLK_TX_ICN_DMU>,
+ <CLK_EXT2F_A9>,
+ <CLK_ICN_LMI>,
+ <CLK_ICN_SBC>;
};
};
};
blue {
- label = "a1000:blue:usr";
+ label = "a1000:blue:pwr";
gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
};
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>;
};
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>;
};
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 43>, <&ahb_gates 44>,
- <&dram_gates 26>;
+ clocks = <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>, <&de_be0_clk>,
+ <&tcon0_ch1_clk>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 43>, <&ahb_gates 44>,
- <&ahb_gates 46>,
+ clocks = <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>, <&ahb_gates 46>,
+ <&de_be0_clk>, <&de_fe0_clk>, <&tcon0_ch1_clk>,
<&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 44>, <&ahb_gates 46>,
+ clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&ahb_gates 46>,
+ <&de_be0_clk>, <&de_fe0_clk>, <&tcon0_ch0_clk>,
<&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 34>,
- <&ahb_gates 36>, <&ahb_gates 44>,
- <&ahb_gates 46>,
- <&dram_gates 5>, <&dram_gates 25>, <&dram_gates 26>;
+ clocks = <&ahb_gates 34>, <&ahb_gates 36>,
+ <&ahb_gates 44>, <&ahb_gates 46>,
+ <&de_be0_clk>, <&de_fe0_clk>,
+ <&tcon0_ch1_clk>, <&dram_gates 5>,
+ <&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
};
"dram_de_mp", "dram_ace";
};
+ de_be0_clk: clk@01c20104 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20104 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be0";
+ };
+
+ de_be1_clk: clk@01c20108 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20108 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be1";
+ };
+
+ de_fe0_clk: clk@01c2010c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c2010c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe0";
+ };
+
+ de_fe1_clk: clk@01c20110 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20110 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe1";
+ };
+
+
+ tcon0_ch0_clk: clk@01c20118 {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c20118 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch0-sclk";
+
+ };
+
+ tcon1_ch0_clk: clk@01c2011c {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c2011c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch0-sclk";
+
+ };
+
+ tcon0_ch1_clk: clk@01c2012c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c2012c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch1-sclk";
+
+ };
+
+ tcon1_ch1_clk: clk@01c20130 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c20130 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch1-sclk";
+
+ };
+
ve_clk: clk@01c2013c {
#clock-cells = <0>;
#reset-cells = <0>;
#dma-cells = <2>;
};
+ nfc: nand@01c03000 {
+ compatible = "allwinner,sun4i-a10-nand";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <37>;
+ clocks = <&ahb_gates 13>, <&nand_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 3>;
+ dma-names = "rxtx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
spi0: spi@01c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
#interrupt-cells = <3>;
#gpio-cells = <3>;
- pwm0_pins_a: pwm0@0 {
- allwinner,pins = "PB2";
- allwinner,function = "pwm";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- pwm1_pins_a: pwm1@0 {
- allwinner,pins = "PI3";
- allwinner,function = "pwm";
+ emac_pins_a: emac0@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "emac";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PB22", "PB23";
- allwinner,function = "uart0";
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart0_pins_b: uart0@1 {
- allwinner,pins = "PF2", "PF4";
- allwinner,function = "uart0";
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB18", "PB19";
+ allwinner,function = "i2c1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart1_pins_a: uart1@0 {
- allwinner,pins = "PA10", "PA11";
- allwinner,function = "uart1";
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB20", "PB21";
+ allwinner,function = "i2c2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PB0", "PB1";
- allwinner,function = "i2c0";
+ ir0_rx_pins_a: ir0@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "ir0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PB18", "PB19";
- allwinner,function = "i2c1";
+ ir0_tx_pins_a: ir0@1 {
+ allwinner,pins = "PB3";
+ allwinner,function = "ir0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PB20", "PB21";
- allwinner,function = "i2c2";
+ ir1_rx_pins_a: ir1@0 {
+ allwinner,pins = "PB23";
+ allwinner,function = "ir1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- emac_pins_a: emac0@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA9", "PA10",
- "PA11", "PA12", "PA13", "PA14",
- "PA15", "PA16";
- allwinner,function = "emac";
+ ir1_tx_pins_a: ir1@1 {
+ allwinner,pins = "PB22";
+ allwinner,function = "ir1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
- ir0_rx_pins_a: ir0@0 {
- allwinner,pins = "PB4";
- allwinner,function = "ir0";
+ ps20_pins_a: ps20@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir0_tx_pins_a: ir0@1 {
- allwinner,pins = "PB3";
- allwinner,function = "ir0";
+ ps21_pins_a: ps21@0 {
+ allwinner,pins = "PH12", "PH13";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_rx_pins_a: ir1@0 {
- allwinner,pins = "PB23";
- allwinner,function = "ir1";
+ pwm0_pins_a: pwm0@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_tx_pins_a: ir1@1 {
- allwinner,pins = "PB22";
- allwinner,function = "ir1";
+ pwm1_pins_a: pwm1@0 {
+ allwinner,pins = "PI3";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ spdif_tx_pins_a: spdif@0 {
+ allwinner,pins = "PB13";
+ allwinner,function = "spdif";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
spi0_pins_a: spi0@0 {
allwinner,pins = "PI11", "PI12", "PI13";
allwinner,function = "spi0";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps20_pins_a: ps20@0 {
- allwinner,pins = "PI20", "PI21";
- allwinner,function = "ps2";
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PB22", "PB23";
+ allwinner,function = "uart0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps21_pins_a: ps21@0 {
- allwinner,pins = "PH12", "PH13";
- allwinner,function = "ps2";
+ uart0_pins_b: uart0@1 {
+ allwinner,pins = "PF2", "PF4";
+ allwinner,function = "uart0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- spdif_tx_pins_a: spdif@0 {
- allwinner,pins = "PB13";
- allwinner,function = "spdif";
+ uart1_pins_a: uart1@0 {
+ allwinner,pins = "PA10", "PA11";
+ allwinner,function = "uart1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PG12";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
mmc0_cd_pin_t004: mmc0_cd_pin@0 {
allwinner,pins = "PG1";
allwinner,function = "gpio_in";
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usb1_vbus_pin_a {
allwinner,pins = "PG13";
};
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
status = "okay";
};
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp152: pmic@30 {
+ compatible = "x-powers,axp152";
+ reg = <0x30>;
+ interrupts = <0>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>;
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
&ohci0 {
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
led_pins_mk802: led_pins@0 {
allwinner,pins = "PB2";
status = "okay";
};
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
status = "okay";
};
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>,
+ <&spi2_cs0_pins_a>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 0 2 GPIO_ACTIVE_HIGH>;
};
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
+ regulator-name = "vcc-wifi1";
+};
+
+®_ldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi2";
};
®_usb1_vbus {
allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ spi2_pins_a: spi2@0 {
+ allwinner,pins = "PB12", "PB13", "PB14";
+ allwinner,function = "spi2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spi2_cs0_pins_a: spi2_cs0@0 {
+ allwinner,pins = "PB11";
+ allwinner,function = "spi2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&sram_a {
/dts-v1/;
#include "sun5i-a13.dtsi"
-#include "sunxi-common-regulators.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun5i-reference-design-tablet.dtsi"
/ {
model = "Difrnce DIT4350";
compatible = "difrnce,dit4350", "allwinner,sun5i-a13";
-
- aliases {
- serial0 = &uart1;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- /* TODO: backlight uses axp gpio1 as enable pin */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&cpu0 {
- cpu-supply = <®_dcdc2>;
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic@34 {
- reg = <0x34>;
- interrupts = <0>;
- };
-};
-
-#include "axp209.dtsi"
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-
- pcf8563: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&lradc {
- vref-supply = <®_ldo2>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
- status = "okay";
-};
-
-&otg_sram {
- status = "okay";
-};
-
-&pio {
- mmc0_cd_pin_d709: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1250000>;
- regulator-name = "vdd-int-pll";
-};
-
-®_ldo1 {
- regulator-name = "vdd-rtc";
-};
-
-®_ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
-};
-
-®_ldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
-};
-
-®_usb0_vbus {
- gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usb0_vbus_pin_a {
- allwinner,pins = "PG12";
-};
-
-&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_ldo3>;
- status = "okay";
};
/dts-v1/;
#include "sun5i-a13.dtsi"
-#include "sun5i-q8-common.dtsi"
+#include "sun5i-reference-design-tablet.dtsi"
/ {
model = "Q8 A13 Tablet";
compatible = "allwinner,q8-a13", "allwinner,sun5i-a13";
+
+ panel: panel {
+ compatible = "urt,umsh-8596md-t", "simple-panel";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ /* TODO: lcd panel uses axp gpio0 as enable pin */
+ backlight = <&backlight>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_lcd>;
+ };
+ };
+ };
+};
+
+&be0 {
+ status = "okay";
};
-®_ldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_rgb666_pins>;
+ status = "okay";
};
-&usbphy {
- usb1_vbus-supply = <®_ldo3>;
+&tcon0_out {
+ tcon0_out_lcd: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
};
/dts-v1/;
#include "sun5i-a13.dtsi"
-#include "sunxi-common-regulators.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sun5i-reference-design-tablet.dtsi"
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
/ {
model = "Utoo P66";
compatible = "utoo,p66", "allwinner,sun5i-a13";
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- /* Note levels of 10 / 20% result in backlight off */
- brightness-levels = <0 30 40 50 60 70 80 90 100>;
- default-brightness-level = <6>;
- /* TODO: backlight uses axp gpio1 as enable pin */
+ /* The P66 uses the uart pins as gpios */
+ aliases {
+ /delete-property/serial0;
+ };
+
+ chosen {
+ /delete-property/stdout-path;
};
i2c_lcd: i2c@0 {
};
};
-&codec {
- pinctrl-names = "default";
- pinctrl-0 = <&codec_pa_pin>;
- allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
- status = "okay";
-};
-
-&cpu0 {
- cpu-supply = <®_dcdc2>;
+&backlight {
+ /* Note levels of 10 / 20% result in backlight off */
+ brightness-levels = <0 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <6>;
};
-&ehci0 {
- status = "okay";
+&codec {
+ allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic@34 {
- reg = <0x34>;
- interrupts = <0>;
- };
+&codec_pa_pin {
+ allwinner,pins = "PG3";
};
-#include "axp209.dtsi"
-
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-
icn8318: touchscreen@40 {
compatible = "chipone,icn8318";
reg = <0x40>;
touchscreen-inverted-x;
touchscreen-swapped-x-y;
};
-
- pcf8563: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&lradc {
- vref-supply = <®_ldo2>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_p66>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
- status = "okay";
};
&mmc2 {
};
};
-&otg_sram {
- status = "okay";
-};
-
&pio {
- codec_pa_pin: codec_pa_pin@0 {
- allwinner,pins = "PG3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_p66: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
i2c_lcd_pins: i2c_lcd_pin@0 {
allwinner,pins = "PG10", "PG12";
allwinner,function = "gpio_out";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- usb0_vbus_pin_a: usb0_vbus_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-int-pll";
-};
-
-®_ldo1 {
- regulator-name = "vdd-rtc";
-};
-
-®_ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
-};
-
-®_ldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
};
®_usb0_vbus {
gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- status = "okay";
};
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
+&uart1 {
+ /* The P66 uses the uart pins as gpios */
+ status = "disabled";
};
-&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_ldo3>;
- status = "okay";
+&usb0_vbus_pin_a {
+ allwinner,pins = "PB4";
};
};
};
+ display-engine {
+ compatible = "allwinner,sun5i-a13-display-engine";
+ allwinner,pipelines = <&fe0>;
+ };
+
soc@01c00000 {
+ tcon0: lcd-controller@01c0c000 {
+ compatible = "allwinner,sun5i-a13-tcon";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <44>;
+ resets = <&tcon_ch0_clk 1>;
+ reset-names = "lcd";
+ clocks = <&ahb_gates 36>,
+ <&tcon_ch0_clk>,
+ <&tcon_ch1_clk>;
+ clock-names = "ahb",
+ "tcon-ch0",
+ "tcon-ch1";
+ clock-output-names = "tcon-pixel-clock";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
pwm: pwm@01c20e00 {
compatible = "allwinner,sun5i-a13-pwm";
reg = <0x01c20e00 0xc>;
#pwm-cells = <3>;
status = "disabled";
};
+
+ fe0: display-frontend@01e00000 {
+ compatible = "allwinner,sun5i-a13-display-frontend";
+ reg = <0x01e00000 0x20000>;
+ interrupts = <47>;
+ clocks = <&ahb_gates 46>, <&de_fe_clk>,
+ <&dram_gates 25>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&de_fe_clk>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe0_out_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe0>;
+ };
+ };
+ };
+ };
+
+ be0: display-backend@01e60000 {
+ compatible = "allwinner,sun5i-a13-display-backend";
+ reg = <0x01e60000 0x10000>;
+ clocks = <&ahb_gates 44>, <&de_be_clk>,
+ <&dram_gates 26>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&de_be_clk>;
+ status = "disabled";
+
+ assigned-clocks = <&de_be_clk>;
+ assigned-clock-rates = <300000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be0_in_fe0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be0>;
+ };
+ };
+
+ be0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be0_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_be0>;
+ };
+ };
+ };
+ };
};
};
&pio {
compatible = "allwinner,sun5i-a13-pinctrl";
+ lcd_rgb666_pins: lcd_rgb666@0 {
+ allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+ "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+ "PD24", "PD25", "PD26", "PD27";
+ allwinner,function = "lcd0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
uart1_pins_a: uart1@0 {
allwinner,pins = "PE10", "PE11";
allwinner,function = "uart1";
+++ /dev/null
-/*
- * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-#include "sunxi-q8-common.dtsi"
-
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
- aliases {
- serial0 = &uart1;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- /* TODO: backlight uses axp gpio1 as enable pin */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&cpu0 {
- cpu-supply = <®_dcdc2>;
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&i2c0 {
- axp209: pmic@34 {
- reg = <0x34>;
- interrupts = <0>;
- };
-};
-
-&i2c1 {
- pcf8563: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-#include "axp209.dtsi"
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
- status = "okay";
-};
-
-&otg_sram {
- status = "okay";
-};
-
-&pio {
- mmc0_cd_pin_q8: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_pin_a: usb0_vbus_pin@0 {
- allwinner,pins = "PG12";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-int-pll";
-};
-
-®_ldo1 {
- regulator-name = "vdd-rtc";
-};
-
-®_ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
-};
-
-®_usb0_vbus {
- gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- usb0_vbus-supply = <®_usb0_vbus>;
- status = "okay";
-};
};
};
};
-
- tcon0: lcd-controller@01c0c000 {
- compatible = "allwinner,sun5i-a13-tcon";
- reg = <0x01c0c000 0x1000>;
- interrupts = <44>;
- resets = <&tcon_ch0_clk 1>;
- reset-names = "lcd";
- clocks = <&ahb_gates 36>,
- <&tcon_ch0_clk>,
- <&tcon_ch1_clk>;
- clock-names = "ahb",
- "tcon-ch0",
- "tcon-ch1";
- clock-output-names = "tcon-pixel-clock";
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tcon0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- tcon0_in_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_out_tcon0>;
- };
- };
-
- tcon0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- tcon0_out_tve0: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&tve0_in_tcon0>;
- };
- };
- };
- };
-
- fe0: display-frontend@01e00000 {
- compatible = "allwinner,sun5i-a13-display-frontend";
- reg = <0x01e00000 0x20000>;
- interrupts = <47>;
- clocks = <&ahb_gates 46>, <&de_fe_clk>,
- <&dram_gates 25>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_fe_clk>;
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- fe0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- fe0_out_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_in_fe0>;
- };
- };
- };
- };
-
- be0: display-backend@01e60000 {
- compatible = "allwinner,sun5i-a13-display-backend";
- reg = <0x01e60000 0x10000>;
- clocks = <&ahb_gates 44>, <&de_be_clk>,
- <&dram_gates 26>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_be_clk>;
- status = "disabled";
-
- assigned-clocks = <&de_be_clk>;
- assigned-clock-rates = <300000000>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- be0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- be0_in_fe0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&fe0_out_be0>;
- };
- };
-
- be0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- be0_out_tcon0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tcon0_in_be0>;
- };
- };
- };
- };
};
+};
- display-engine {
- compatible = "allwinner,sun5i-a13-display-engine";
- allwinner,pipelines = <&fe0>;
+&tcon0_out {
+ tcon0_out_tve0: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tve0_in_tcon0>;
};
};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include "sunxi-reference-design-tablet.dtsi"
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ serial0 = &uart1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ /* TODO: backlight uses axp gpio1 as enable pin */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+&i2c1 {
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&lradc {
+ vref-supply = <®_ldo2>;
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PG10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PG2";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_pin_a: usb0_vbus_pin@0 {
+ allwinner,pins = "PG12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_usb0_vbus {
+ gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_ldo3>;
+ status = "okay";
+};
};
pll3x2: pll3x2_clk {
- compatible = "fixed-factor-clock";
+ compatible = "allwinner,sun4i-a10-pll3-2x-clk", "fixed-factor-clock";
#clock-cells = <0>;
clock-div = <1>;
clock-mult = <2>;
pinctrl-0 = <&led_pins_m9>;
blue {
- label = "m9:blue:usr";
+ label = "m9:blue:pwr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy@1 {
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins@0 {
allwinner,pins = "PH13";
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
pinctrl-0 = <&led_pins_m9>;
blue {
- label = "m9:blue:usr";
+ label = "a1000g:blue:pwr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy@1 {
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins@0 {
allwinner,pins = "PH13";
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2016 Luo Yi <luoyi.ly@gmail.com>
+ *
+ * Thanks to the original work by Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "Banana Pi BPI-M1-Plus";
+ compatible = "sinovoip,bpi-m1-plus", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bpi_m1p>;
+
+ green {
+ label = "bananapi-m1-plus:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "bananapi-m1-plus:pwr:usr";
+ gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ mmc3_pwrseq: mmc3_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pwrseq_pin_bpi_m1p>;
+ reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bpi_m1p>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m1p>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&mmc3_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ enable-sdio-wakeup;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc3_pins_a {
+ /* AP6210 requires pull-up */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ gmac_power_pin_bpi_m1p: gmac_power_pin@0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bpi_m1p: led_pins@0 {
+ allwinner,pins = "PH24", "PH25";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_bpi_m1p: mmc0_cd_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc3_pwrseq_pin_bpi_m1p: mmc3_pwrseq_pin@0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
&gmac {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
- phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
status = "okay";
- phy1: ethernet-phy@1 {
- reg = <1>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch: ethernet-switch@1e {
+ compatible = "brcm,bcm53125";
+ reg = <30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port@0 {
+ reg = <0>;
+ label = "lan2";
+ };
+
+ port1: port@1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port2: port@2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port3: port@3 {
+ reg = <3>;
+ label = "wan";
+ };
+
+ port4: port@4 {
+ reg = <4>;
+ label = "lan1";
+ };
+
+ port8: port@8 {
+ reg = <8>;
+ label = "cpu";
+ ethernet = <&gmac>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
};
};
status = "okay";
};
-&ohci1 {
- status = "okay";
-};
-
&otg_sram {
status = "okay";
};
#include "axp209.dtsi"
®_ahci_5v {
- gpio = <&pio 1 3 0>; /* PB3 */
+ gpio = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
status = "okay";
};
status = "okay";
};
-®_usb1_vbus {
- status = "okay";
-};
-
®_usb2_vbus {
+ gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
status = "okay";
};
status = "okay";
};
+&usb2_vbus_pin_a {
+ allwinner,pins = "PH12";
+};
+
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>;
usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 43>, <&ahb_gates 44>,
- <&dram_gates 26>;
+ clocks = <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>, <&de_be0_clk>,
+ <&tcon0_ch1_clk>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 44>, <&dram_gates 26>;
+ clocks = <&ahb_gates 36>, <&ahb_gates 44>,
+ <&de_be0_clk>, <&tcon0_ch0_clk>,
+ <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&pll3>, <&pll5 1>,
- <&ahb_gates 34>, <&ahb_gates 36>, <&ahb_gates 44>,
+ clocks = <&ahb_gates 34>, <&ahb_gates 36>,
+ <&ahb_gates 44>,
+ <&de_be0_clk>, <&tcon0_ch1_clk>,
<&dram_gates 5>, <&dram_gates 26>;
status = "disabled";
};
<5>, <6>, <7>,
<8>, <10>;
clock-output-names = "apb0_codec", "apb0_spdif",
- "apb0_ac97", "apb0_iis0", "apb0_iis1",
+ "apb0_ac97", "apb0_i2s0", "apb0_i2s1",
"apb0_pio", "apb0_ir0", "apb0_ir1",
- "apb0_iis2", "apb0_keypad";
+ "apb0_i2s2", "apb0_keypad";
};
apb1: clk@01c20058 {
clock-output-names = "ir1";
};
+ i2s0_clk: clk@01c200b8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200b8 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "i2s0";
+ };
+
+ ac97_clk: clk@01c200bc {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200bc 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "ac97";
+ };
+
spdif_clk: clk@01c200c0 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod1-clk";
clock-output-names = "spi3";
};
+ i2s1_clk: clk@01c200d8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200d8 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "i2s1";
+ };
+
+ i2s2_clk: clk@01c200dc {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200dc 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "i2s2";
+ };
+
dram_gates: clk@01c20100 {
#clock-cells = <1>;
compatible = "allwinner,sun4i-a10-dram-gates-clk";
"dram_de_mp", "dram_ace";
};
+ de_be0_clk: clk@01c20104 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20104 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be0";
+ };
+
+ de_be1_clk: clk@01c20108 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20108 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be1";
+ };
+
+ de_fe0_clk: clk@01c2010c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c2010c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe0";
+ };
+
+ de_fe1_clk: clk@01c20110 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20110 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe1";
+ };
+
+ tcon0_ch0_clk: clk@01c20118 {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c20118 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch0-sclk";
+
+ };
+
+ tcon1_ch0_clk: clk@01c2011c {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c2011c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch0-sclk";
+
+ };
+
+ tcon0_ch1_clk: clk@01c2012c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c2012c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch1-sclk";
+
+ };
+
+ tcon1_ch1_clk: clk@01c20130 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c20130 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch1-sclk";
+
+ };
+
ve_clk: clk@01c2013c {
#clock-cells = <0>;
#reset-cells = <0>;
#dma-cells = <2>;
};
+ nfc: nand@01c03000 {
+ compatible = "allwinner,sun4i-a10-nand";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb_gates 13>, <&nand_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 3>;
+ dma-names = "rxtx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
spi0: spi@01c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
#interrupt-cells = <3>;
#gpio-cells = <3>;
- pwm0_pins_a: pwm0@0 {
- allwinner,pins = "PB2";
- allwinner,function = "pwm";
+ clk_out_a_pins_a: clk_out_a@0 {
+ allwinner,pins = "PI12";
+ allwinner,function = "clk_out_a";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- pwm1_pins_a: pwm1@0 {
- allwinner,pins = "PI3";
- allwinner,function = "pwm";
+ clk_out_b_pins_a: clk_out_b@0 {
+ allwinner,pins = "PI13";
+ allwinner,function = "clk_out_b";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PB22", "PB23";
- allwinner,function = "uart0";
+ emac_pins_a: emac0@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "emac";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart2_pins_a: uart2@0 {
- allwinner,pins = "PI16", "PI17", "PI18", "PI19";
- allwinner,function = "uart2";
+ gmac_pins_mii_a: gmac_mii@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "gmac";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart3_pins_a: uart3@0 {
- allwinner,pins = "PG6", "PG7", "PG8", "PG9";
- allwinner,function = "uart3";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ gmac_pins_rgmii_a: gmac_rgmii@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA10",
+ "PA11", "PA12", "PA13",
+ "PA15", "PA16";
+ allwinner,function = "gmac";
+ /*
+ * data lines in RGMII mode use DDR mode
+ * and need a higher signal drive strength
+ */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart3_pins_b: uart3@1 {
- allwinner,pins = "PH0", "PH1";
- allwinner,function = "uart3";
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart4_pins_a: uart4@0 {
- allwinner,pins = "PG10", "PG11";
- allwinner,function = "uart4";
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB18", "PB19";
+ allwinner,function = "i2c1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart4_pins_b: uart4@1 {
- allwinner,pins = "PH4", "PH5";
- allwinner,function = "uart4";
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB20", "PB21";
+ allwinner,function = "i2c2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart5_pins_a: uart5@0 {
- allwinner,pins = "PI10", "PI11";
- allwinner,function = "uart5";
+ i2c3_pins_a: i2c3@0 {
+ allwinner,pins = "PI0", "PI1";
+ allwinner,function = "i2c3";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart6_pins_a: uart6@0 {
- allwinner,pins = "PI12", "PI13";
- allwinner,function = "uart6";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir0_rx_pins_a: ir0@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "ir0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart7_pins_a: uart7@0 {
- allwinner,pins = "PI20", "PI21";
- allwinner,function = "uart7";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir0_tx_pins_a: ir0@1 {
+ allwinner,pins = "PB3";
+ allwinner,function = "ir0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PB0", "PB1";
- allwinner,function = "i2c0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir1_rx_pins_a: ir1@0 {
+ allwinner,pins = "PB23";
+ allwinner,function = "ir1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PB18", "PB19";
- allwinner,function = "i2c1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir1_tx_pins_a: ir1@1 {
+ allwinner,pins = "PB22";
+ allwinner,function = "ir1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PB20", "PB21";
- allwinner,function = "i2c2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c3_pins_a: i2c3@0 {
- allwinner,pins = "PI0", "PI1";
- allwinner,function = "i2c3";
+ mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc2_pins_a: mmc2@0 {
+ allwinner,pins = "PC6", "PC7", "PC8",
+ "PC9", "PC10", "PC11";
+ allwinner,function = "mmc2";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc3_pins_a: mmc3@0 {
+ allwinner,pins = "PI4", "PI5", "PI6",
+ "PI7", "PI8", "PI9";
+ allwinner,function = "mmc3";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- emac_pins_a: emac0@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA9", "PA10",
- "PA11", "PA12", "PA13", "PA14",
- "PA15", "PA16";
- allwinner,function = "emac";
+ ps20_pins_a: ps20@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- clk_out_a_pins_a: clk_out_a@0 {
- allwinner,pins = "PI12";
- allwinner,function = "clk_out_a";
+ ps21_pins_a: ps21@0 {
+ allwinner,pins = "PH12", "PH13";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- clk_out_b_pins_a: clk_out_b@0 {
- allwinner,pins = "PI13";
- allwinner,function = "clk_out_b";
+ pwm0_pins_a: pwm0@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- gmac_pins_mii_a: gmac_mii@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA9", "PA10",
- "PA11", "PA12", "PA13", "PA14",
- "PA15", "PA16";
- allwinner,function = "gmac";
+ pwm1_pins_a: pwm1@0 {
+ allwinner,pins = "PI3";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- gmac_pins_rgmii_a: gmac_rgmii@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA10",
- "PA11", "PA12", "PA13",
- "PA15", "PA16";
- allwinner,function = "gmac";
- /*
- * data lines in RGMII mode use DDR mode
- * and need a higher signal drive strength
- */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spdif_tx_pins_a: spdif@0 {
+ allwinner,pins = "PB13";
+ allwinner,function = "spdif";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
spi0_pins_a: spi0@0 {
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- mmc0_pins_a: mmc0@0 {
- allwinner,pins = "PF0", "PF1", "PF2",
- "PF3", "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PB22", "PB23";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
- allwinner,pins = "PH1";
- allwinner,function = "gpio_in";
+ uart2_pins_a: uart2@0 {
+ allwinner,pins = "PI16", "PI17", "PI18", "PI19";
+ allwinner,function = "uart2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- mmc2_pins_a: mmc2@0 {
- allwinner,pins = "PC6", "PC7", "PC8",
- "PC9", "PC10", "PC11";
- allwinner,function = "mmc2";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- mmc3_pins_a: mmc3@0 {
- allwinner,pins = "PI4", "PI5", "PI6",
- "PI7", "PI8", "PI9";
- allwinner,function = "mmc3";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir0_rx_pins_a: ir0@0 {
- allwinner,pins = "PB4";
- allwinner,function = "ir0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart3_pins_a: uart3@0 {
+ allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir0_tx_pins_a: ir0@1 {
- allwinner,pins = "PB3";
- allwinner,function = "ir0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart3_pins_b: uart3@1 {
+ allwinner,pins = "PH0", "PH1";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_rx_pins_a: ir1@0 {
- allwinner,pins = "PB23";
- allwinner,function = "ir1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart4_pins_a: uart4@0 {
+ allwinner,pins = "PG10", "PG11";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_tx_pins_a: ir1@1 {
- allwinner,pins = "PB22";
- allwinner,function = "ir1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart4_pins_b: uart4@1 {
+ allwinner,pins = "PH4", "PH5";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps20_pins_a: ps20@0 {
- allwinner,pins = "PI20", "PI21";
- allwinner,function = "ps2";
+ uart5_pins_a: uart5@0 {
+ allwinner,pins = "PI10", "PI11";
+ allwinner,function = "uart5";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps21_pins_a: ps21@0 {
- allwinner,pins = "PH12", "PH13";
- allwinner,function = "ps2";
+ uart6_pins_a: uart6@0 {
+ allwinner,pins = "PI12", "PI13";
+ allwinner,function = "uart6";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- spdif_tx_pins_a: spdif@0 {
- allwinner,pins = "PB13";
- allwinner,function = "spdif";
+ uart7_pins_a: uart7@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "uart7";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
status = "disabled";
};
+ i2s1: i2s@01c22000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c22000 0x400>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 4>, <&i2s1_clk>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 4>,
+ <&dma SUN4I_DMA_NORMAL 4>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2s0: i2s@01c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 3>, <&i2s0_clk>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 3>,
+ <&dma SUN4I_DMA_NORMAL 3>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
lradc: lradc@01c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>;
reg = <0x01c23800 0x200>;
};
+ i2s2: i2s@01c24400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c24400 0x400>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 8>, <&i2s2_clk>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 6>,
+ <&dma SUN4I_DMA_NORMAL 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
rtp: rtp@01c25000 {
compatible = "allwinner,sun5i-a13-ts";
reg = <0x01c25000 0x100>;
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sun8i-reference-design-tablet.dtsi"
+
+/ {
+ model = "INet-86DZ Rev 01";
+ compatible = "primux,inet86dz", "allwinner,sun8i-a23";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
+};
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sun8i-reference-design-tablet.dtsi"
+
+/ {
+ model = "Polaroid MID2407PXE03 tablet";
+ compatible = "polaroid,mid2407pxe03", "allwinner,sun8i-a23";
+};
/dts-v1/;
#include "sun8i-a23.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun8i-reference-design-tablet.dtsi"
/ {
model = "Polaroid MID2809PXE04 tablet";
compatible = "polaroid,mid2809pxe04", "allwinner,sun8i-a23";
-
- aliases {
- serial0 = &r_uart;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_mid2809>;
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-};
-
-&lradc {
- vref-supply = <®_vcc3v0>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mid2809>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
- status = "okay";
-};
-
-&pio {
- bl_en_pin_mid2809: bl_en_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_mid2809: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-&r_rsb {
- status = "okay";
-
- axp22x: pmic@3a3 {
- compatible = "x-powers,axp223";
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- eldoin-supply = <®_dcdc1>;
- };
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
-};
-
-#include "axp22x.dtsi"
-
-®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io";
-};
-
-®_aldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2350000>;
- regulator-max-microvolt = <2650000>;
- regulator-name = "vdd-dll";
-};
-
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pll-avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpus";
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-sys";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_rtc_ldo {
- regulator-name = "vcc-rtc";
-};
-
-&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
-};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
};
model = "Q8 A23 Tablet";
compatible = "allwinner,q8-a23", "allwinner,sun8i-a23";
};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
-};
/dts-v1/;
#include "sun8i-a33.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun8i-reference-design-tablet.dtsi"
/ {
model = "Allwinner GA10H Quad Core Tablet (v1.1)";
compatible = "allwinner,ga10h-v1.1", "allwinner,sun8i-a33";
-
- aliases {
- serial0 = &r_uart;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
};
&ehci0 {
status = "okay";
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-};
-
&lradc {
- vref-supply = <®_vcc3v0>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-
button@600 {
label = "Back";
linux,code = <KEY_BACK>;
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
- status = "okay";
-};
-
&ohci0 {
status = "okay";
};
-
-&pio {
- mmc0_cd_pin_q8h: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
-};
model = "Q8 A33 Tablet";
compatible = "allwinner,q8-a33", "allwinner,sun8i-a33";
};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
-};
--- /dev/null
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Plus";
+ compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_led_bpi_m2p>;
+
+ pwr_led {
+ label = "bananapi-m2-plus:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_bpi_m2p>;
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_en_bpi_m2p>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&r_pio {
+ pwr_led_bpi_m2p: led_pins@0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_bpi_m2p: key_pins@0 {
+ allwinner,pins = "PL3";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ wifi_en_bpi_m2p: wifi_en_pin {
+ allwinner,pins = "PL7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ /* USB VBUS is on as long as VCC-IO is on */
+ status = "okay";
+};
interrupt-controller;
#interrupt-cells = <3>;
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PA4", "PA5";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PA4", "PA5";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_pins_a: uart1@0 {
+ allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
timer@01c20c00 {
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "sunxi-q8-common.dtsi"
+#include "sunxi-reference-design-tablet.dtsi"
+#include "sun8i-reference-design-tablet.dtsi"
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
- aliases {
- serial0 = &r_uart;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_q8>;
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
- status = "okay";
-};
-
-&pio {
- bl_en_pin_q8: bl_en_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_q8: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&r_rsb {
- status = "okay";
-
- axp22x: pmic@3a3 {
- compatible = "x-powers,axp223";
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- eldoin-supply = <®_dcdc1>;
- };
-};
-
-#include "axp22x.dtsi"
-
-®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io";
-};
-
-®_aldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2350000>;
- regulator-max-microvolt = <2650000>;
- regulator-name = "vdd-dll";
-};
-
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pll-avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpus";
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-sys";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_rtc_ldo {
- regulator-name = "vcc-rtc";
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
+&ehci0 {
+ status = "okay";
};
-&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
};
--- /dev/null
+/*
+ * Copyright 2016 Quentin Schulz
+ *
+ * Quentin Schulz <quentin.schulz@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Allwinner R16 EVB (Parrot)";
+ compatible = "allwinner,parrot", "allwinner,sun8i-a33";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_parrot>;
+
+ led1 {
+ label = "parrot:led1:usr";
+ gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+ };
+
+ led2 {
+ label = "parrot:led2:usr";
+ gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
+ };
+
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ /*
+ * FIXME: An as-yet-unknown accelerometer is connected to this
+ * i2c bus.
+ */
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@0 {
+ label = "V+";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <190000>;
+ };
+
+ button@1 {
+ label = "V-";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <390000>;
+ };
+
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_parrot>;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_parrot>;
+ vmmc-supply = <®_aldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_parrot: mmc0_cd_pin@0 {
+ allwinner,pins = "PD14";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_parrot: led_pins@0 {
+ allwinner,pins = "PE16", "PE17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_det: usb0_id_detect_pin@0 {
+ allwinner,pins = "PD10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_parrot: usb1_vbus_pin@0 {
+ allwinner,pins = "PD12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ wifi_reset_pin_parrot: wifi_reset_pin@0 {
+ allwinner,pins = "PL6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ drivevbus-supply = <®_vcc5v0>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ /*
+ * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered.
+ * Remove next line once it is possible to sync two regulators.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi0";
+};
+
+®_dldo2 {
+ /*
+ * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered.
+ * Remove next line once it is possible to sync two regulators.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi1";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0-csi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-dsp";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "eldo3";
+};
+
+®_usb1_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_parrot>;
+ gpio = <&pio 3 12 GPIO_ACTIVE_HIGH>; /* PD12 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_b>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_det>;
+ usb0_vbus-supply = <®_drivevbus>;
+ usb0_id_det-gpios = <&pio 3 10 GPIO_ACTIVE_HIGH>; /* PD10 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include "sunxi-reference-design-tablet.dtsi"
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ serial0 = &r_uart;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ bl_en_pin: bl_en_pin@0 {
+ allwinner,pins = "PH6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ drivevbus-supply = <®_vcc5v0>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&r_uart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins_a>;
+ status = "okay";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_drivevbus>;
+ status = "okay";
+};
/dts-v1/;
#include "sun9i-a80.dtsi"
-#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
};
};
-&pio {
- led_pins_cubieboard4: led-pins@0 {
- allwinner,pins = "PH6", "PH17";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
- allwinner,pins = "PH18";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
cd-inverted;
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
allwinner,drive = <SUN4I_PINCTRL_40_MA>;
};
+&pio {
+ led_pins_cubieboard4: led-pins@0 {
+ allwinner,pins = "PH6", "PH17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
+ allwinner,pins = "PH18";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
&r_ir {
status = "okay";
};
&r_rsb {
status = "okay";
+
+ axp809: pmic@3a3 {
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ /*
+ * TODO: This should be handled by the
+ * USB PHY driver.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc33-usbh";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pb-io-cam";
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_dc5ldo: dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus-09-usbh";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys-usb0-hdmi";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1425000>;
+ regulator-max-microvolt = <1575000>;
+ regulator-name = "vcc-dram";
+ };
+
+ reg_dldo1: dldo1 {
+ /*
+ * The WiFi chip supports a wide range
+ * (3.0 ~ 4.8V) of voltages, and so does
+ * this regulator (3.0 ~ 4.2V), but
+ * Allwinner SDK always sets it to 3.3V.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dvdd-cam";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pe";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pm-codec-io1";
+ };
+
+ reg_ldo_io0: ldo_io0 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pg";
+ };
+
+ reg_ldo_io1: ldo_io1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa-gmac-2v5";
+ };
+
+ reg_rtc_ldo: rtc_ldo {
+ regulator-name = "vcc-rtc-vdd1v8-io";
+ };
+ };
+ };
};
+#include "axp809.dtsi"
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
/dts-v1/;
#include "sun9i-a80.dtsi"
-#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
};
};
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_optimus>;
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ };
+
reg_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
status = "okay";
};
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+};
+
&ohci0 {
status = "okay";
};
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <4>;
- cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
- cd-inverted;
- status = "okay";
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <8>;
- non-removable;
- cap-mmc-hw-reset;
- status = "okay";
-};
-
-&mmc2_8bit_pins {
- /* Increase drive strength for DDR modes */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
-};
-
-®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_optimus>;
- gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- status = "okay";
-};
-
&r_ir {
status = "okay";
};
&r_rsb {
status = "okay";
+
+ axp809: pmic@3a3 {
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ /*
+ * TODO: This should be handled by the
+ * USB PHY driver.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc33-usbh";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pb-io-cam";
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_dc5ldo: dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus-09-usbh";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys-usb0-hdmi";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1425000>;
+ regulator-max-microvolt = <1575000>;
+ regulator-name = "vcc-dram";
+ };
+
+ reg_dldo1: dldo1 {
+ /*
+ * The WiFi chip supports a wide range
+ * (3.0 ~ 4.8V) of voltages, and so does
+ * this regulator (3.0 ~ 4.2V), but
+ * Allwinner SDK always sets it to 3.3V.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dvdd-cam";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pe";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pm-codec-io1";
+ };
+
+ reg_ldo_io0: ldo_io0 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pg";
+ };
+
+ reg_ldo_io1: ldo_io1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa-gmac-2v5";
+ };
+
+ reg_rtc_ldo: rtc_ldo {
+ regulator-name = "vcc-rtc-vdd1v8-io";
+ };
+ };
+ };
};
+#include "axp809.dtsi"
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
+++ /dev/null
-/*
- * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include "sunxi-common-regulators.dtsi"
-
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-};
-
-&lradc {
- vref-supply = <®_vcc3v0>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sunxi-common-regulators.dtsi"
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
#address-cells = <1>;
#size-cells = <0>;
- clk32k_in: clock {
+ clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
#address-cells = <1>;
#size-cells = <0>;
- clk32k_in: clock {
+ clk32k_in: clock@0 {
compatible = "fixed-clock";
reg = <0>;
#clock-cells = <0>;
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ clock@60006000 {
+ emc-timings-1 {
+ nvidia,ram-code = <1>;
+
+ timing-12750000 {
+ clock-frequency = <12750000>;
+ nvidia,parent-clock-frequency = <408000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
+ clock-names = "emc-parent";
+ };
+ timing-20400000 {
+ clock-frequency = <20400000>;
+ nvidia,parent-clock-frequency = <408000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
+ clock-names = "emc-parent";
+ };
+ timing-40800000 {
+ clock-frequency = <40800000>;
+ nvidia,parent-clock-frequency = <408000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
+ clock-names = "emc-parent";
+ };
+ timing-68000000 {
+ clock-frequency = <68000000>;
+ nvidia,parent-clock-frequency = <408000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
+ clock-names = "emc-parent";
+ };
+ timing-102000000 {
+ clock-frequency = <102000000>;
+ nvidia,parent-clock-frequency = <408000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
+ clock-names = "emc-parent";
+ };
+ timing-204000000 {
+ clock-frequency = <204000000>;
+ nvidia,parent-clock-frequency = <408000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
+ clock-names = "emc-parent";
+ };
+ timing-300000000 {
+ clock-frequency = <300000000>;
+ nvidia,parent-clock-frequency = <600000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
+ clock-names = "emc-parent";
+ };
+ timing-396000000 {
+ clock-frequency = <396000000>;
+ nvidia,parent-clock-frequency = <792000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
+ clock-names = "emc-parent";
+ };
+ timing-528000000 {
+ clock-frequency = <528000000>;
+ nvidia,parent-clock-frequency = <528000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
+ clock-names = "emc-parent";
+ };
+ timing-600000000 {
+ clock-frequency = <600000000>;
+ nvidia,parent-clock-frequency = <600000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
+ clock-names = "emc-parent";
+ };
+ timing-792000000 {
+ clock-frequency = <792000000>;
+ nvidia,parent-clock-frequency = <792000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
+ clock-names = "emc-parent";
+ };
+ timing-924000000 {
+ clock-frequency = <924000000>;
+ nvidia,parent-clock-frequency = <924000000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
+ clock-names = "emc-parent";
+ };
+ };
+ };
+
+ emc@7001b000 {
+ emc-timings-1 {
+ nvidia,ram-code = <1>;
+
+ timing-12750000 {
+ clock-frequency = <12750000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000008>;
+ nvidia,emc-cfg = <0x73240000>;
+ nvidia,emc-cfg-2 = <0x000008c5>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100003>;
+ nvidia,emc-mode-2 = <0x80200008>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80001221>;
+ nvidia,emc-mrs-wait-cnt = <0x000e000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0130b118>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00000000>;
+
+ nvidia,emc-configuration = <
+ 0x00000000 0x00000003
+ 0x00000000 0x00000000
+ 0x00000000 0x00000004
+ 0x0000000a 0x00000005
+ 0x0000000b 0x00000000
+ 0x00000000 0x00000003
+ 0x00000003 0x00000000
+ 0x00000006 0x00000006
+ 0x00000006 0x00000002
+ 0x00000000 0x00000005
+ 0x00000005 0x00010000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000004
+ 0x0000000c 0x0000000d
+ 0x0000000f 0x00000060
+ 0x00000000 0x00000018
+ 0x00000002 0x00000002
+ 0x00000001 0x00000000
+ 0x00000007 0x0000000f
+ 0x00000005 0x00000005
+ 0x00000004 0x00000005
+ 0x00000004 0x00000000
+ 0x00000000 0x00000005
+ 0x00000005 0x00000064
+ 0x00000000 0x00000000
+ 0x00000000 0x106aa298
+ 0x002c00a0 0x00008000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x000fc000 0x000fc000
+ 0x000fc000 0x000fc000
+ 0x0000fc00 0x0000fc00
+ 0x0000fc00 0x0000fc00
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000e0e 0x81f1f108
+ 0x07070004 0x0000003f
+ 0x016eeeee 0x51451400
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x00000007 0x00000000
+ 0x00000042 0x000e000e
+ 0x00000000 0x00000003
+ 0x0000f2f3 0x800001c5
+ 0x0000000a
+ >;
+ };
+
+ timing-20400000 {
+ clock-frequency = <20400000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000008>;
+ nvidia,emc-cfg = <0x73240000>;
+ nvidia,emc-cfg-2 = <0x000008c5>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100003>;
+ nvidia,emc-mode-2 = <0x80200008>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80001221>;
+ nvidia,emc-mrs-wait-cnt = <0x000e000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0130b118>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00000000>;
+
+ nvidia,emc-configuration = <
+ 0x00000000 0x00000005
+ 0x00000000 0x00000000
+ 0x00000000 0x00000004
+ 0x0000000a 0x00000005
+ 0x0000000b 0x00000000
+ 0x00000000 0x00000003
+ 0x00000003 0x00000000
+ 0x00000006 0x00000006
+ 0x00000006 0x00000002
+ 0x00000000 0x00000005
+ 0x00000005 0x00010000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000004
+ 0x0000000c 0x0000000d
+ 0x0000000f 0x0000009a
+ 0x00000000 0x00000026
+ 0x00000002 0x00000002
+ 0x00000001 0x00000000
+ 0x00000007 0x0000000f
+ 0x00000006 0x00000006
+ 0x00000004 0x00000005
+ 0x00000004 0x00000000
+ 0x00000000 0x00000005
+ 0x00000005 0x000000a0
+ 0x00000000 0x00000000
+ 0x00000000 0x106aa298
+ 0x002c00a0 0x00008000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x000fc000 0x000fc000
+ 0x000fc000 0x000fc000
+ 0x0000fc00 0x0000fc00
+ 0x0000fc00 0x0000fc00
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000e0e 0x81f1f108
+ 0x07070004 0x0000003f
+ 0x016eeeee 0x51451400
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x0000000b 0x00000000
+ 0x00000042 0x000e000e
+ 0x00000000 0x00000003
+ 0x0000f2f3 0x8000023a
+ 0x0000000a
+ >;
+ };
+
+ timing-40800000 {
+ clock-frequency = <40800000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000008>;
+ nvidia,emc-cfg = <0x73240000>;
+ nvidia,emc-cfg-2 = <0x000008c5>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100003>;
+ nvidia,emc-mode-2 = <0x80200008>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80001221>;
+ nvidia,emc-mrs-wait-cnt = <0x000e000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0130b118>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00000000>;
+
+ nvidia,emc-configuration = <
+ 0x00000001 0x0000000a
+ 0x00000000 0x00000001
+ 0x00000000 0x00000004
+ 0x0000000a 0x00000005
+ 0x0000000b 0x00000000
+ 0x00000000 0x00000003
+ 0x00000003 0x00000000
+ 0x00000006 0x00000006
+ 0x00000006 0x00000002
+ 0x00000000 0x00000005
+ 0x00000005 0x00010000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000004
+ 0x0000000c 0x0000000d
+ 0x0000000f 0x00000134
+ 0x00000000 0x0000004d
+ 0x00000002 0x00000002
+ 0x00000001 0x00000000
+ 0x00000008 0x0000000f
+ 0x0000000c 0x0000000c
+ 0x00000004 0x00000005
+ 0x00000004 0x00000000
+ 0x00000000 0x00000005
+ 0x00000005 0x0000013f
+ 0x00000000 0x00000000
+ 0x00000000 0x106aa298
+ 0x002c00a0 0x00008000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x000fc000 0x000fc000
+ 0x000fc000 0x000fc000
+ 0x0000fc00 0x0000fc00
+ 0x0000fc00 0x0000fc00
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000e0e 0x81f1f108
+ 0x07070004 0x0000003f
+ 0x016eeeee 0x51451400
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x00000015 0x00000000
+ 0x00000042 0x000e000e
+ 0x00000000 0x00000003
+ 0x0000f2f3 0x80000370
+ 0x0000000a
+ >;
+ };
+
+ timing-68000000 {
+ clock-frequency = <68000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000008>;
+ nvidia,emc-cfg = <0x73240000>;
+ nvidia,emc-cfg-2 = <0x000008c5>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100003>;
+ nvidia,emc-mode-2 = <0x80200008>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80001221>;
+ nvidia,emc-mrs-wait-cnt = <0x000e000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0130b118>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00000000>;
+
+ nvidia,emc-configuration = <
+ 0x00000003 0x00000011
+ 0x00000000 0x00000002
+ 0x00000000 0x00000004
+ 0x0000000a 0x00000005
+ 0x0000000b 0x00000000
+ 0x00000000 0x00000003
+ 0x00000003 0x00000000
+ 0x00000006 0x00000006
+ 0x00000006 0x00000002
+ 0x00000000 0x00000005
+ 0x00000005 0x00010000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000004
+ 0x0000000c 0x0000000d
+ 0x0000000f 0x00000202
+ 0x00000000 0x00000080
+ 0x00000002 0x00000002
+ 0x00000001 0x00000000
+ 0x0000000f 0x0000000f
+ 0x00000013 0x00000013
+ 0x00000004 0x00000005
+ 0x00000004 0x00000001
+ 0x00000000 0x00000005
+ 0x00000005 0x00000213
+ 0x00000000 0x00000000
+ 0x00000000 0x106aa298
+ 0x002c00a0 0x00008000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x000fc000 0x000fc000
+ 0x000fc000 0x000fc000
+ 0x0000fc00 0x0000fc00
+ 0x0000fc00 0x0000fc00
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000e0e 0x81f1f108
+ 0x07070004 0x0000003f
+ 0x016eeeee 0x51451400
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x00000022 0x00000000
+ 0x00000042 0x000e000e
+ 0x00000000 0x00000003
+ 0x0000f2f3 0x8000050e
+ 0x0000000a
+ >;
+ };
+
+ timing-102000000 {
+ clock-frequency = <102000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000008>;
+ nvidia,emc-cfg = <0x73240000>;
+ nvidia,emc-cfg-2 = <0x000008c5>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100003>;
+ nvidia,emc-mode-2 = <0x80200008>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80001221>;
+ nvidia,emc-mrs-wait-cnt = <0x000e000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0130b118>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00000000>;
+
+ nvidia,emc-configuration = <
+ 0x00000004 0x0000001a
+ 0x00000000 0x00000003
+ 0x00000001 0x00000004
+ 0x0000000a 0x00000005
+ 0x0000000b 0x00000001
+ 0x00000001 0x00000003
+ 0x00000003 0x00000000
+ 0x00000006 0x00000006
+ 0x00000006 0x00000002
+ 0x00000000 0x00000005
+ 0x00000005 0x00010000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000004
+ 0x0000000c 0x0000000d
+ 0x0000000f 0x00000304
+ 0x00000000 0x000000c1
+ 0x00000002 0x00000002
+ 0x00000001 0x00000000
+ 0x00000018 0x0000000f
+ 0x0000001c 0x0000001c
+ 0x00000004 0x00000005
+ 0x00000004 0x00000002
+ 0x00000000 0x00000005
+ 0x00000005 0x0000031c
+ 0x00000000 0x00000000
+ 0x00000000 0x106aa298
+ 0x002c00a0 0x00008000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x000fc000 0x000fc000
+ 0x000fc000 0x000fc000
+ 0x0000fc00 0x0000fc00
+ 0x0000fc00 0x0000fc00
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000e0e 0x81f1f108
+ 0x07070004 0x0000003f
+ 0x016eeeee 0x51451400
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x00000033 0x00000000
+ 0x00000042 0x000e000e
+ 0x00000000 0x00000003
+ 0x0000f2f3 0x80000713
+ 0x0000000a
+ >;
+ };
+
+ timing-204000000 {
+ clock-frequency = <204000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000008>;
+ nvidia,emc-cfg = <0x73240000>;
+ nvidia,emc-cfg-2 = <0x000008cd>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100003>;
+ nvidia,emc-mode-2 = <0x80200008>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80001221>;
+ nvidia,emc-mrs-wait-cnt = <0x000e000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0130b118>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00020000>;
+
+ nvidia,emc-configuration = <
+ 0x00000009 0x00000035
+ 0x00000000 0x00000006
+ 0x00000002 0x00000005
+ 0x0000000a 0x00000005
+ 0x0000000b 0x00000002
+ 0x00000002 0x00000003
+ 0x00000003 0x00000000
+ 0x00000005 0x00000005
+ 0x00000006 0x00000002
+ 0x00000000 0x00000004
+ 0x00000006 0x00010000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000003
+ 0x0000000d 0x0000000f
+ 0x00000011 0x00000607
+ 0x00000000 0x00000181
+ 0x00000002 0x00000002
+ 0x00000001 0x00000000
+ 0x00000032 0x0000000f
+ 0x00000038 0x00000038
+ 0x00000004 0x00000005
+ 0x00000004 0x00000006
+ 0x00000000 0x00000005
+ 0x00000005 0x00000638
+ 0x00000000 0x00000000
+ 0x00000000 0x106aa298
+ 0x002c00a0 0x00008000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00080000 0x00080000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00008000 0x00000000
+ 0x00000000 0x00008000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00090000 0x00090000
+ 0x00090000 0x00090000
+ 0x00009000 0x00009000
+ 0x00009000 0x00009000
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000707 0x81f1f108
+ 0x07070004 0x0000003f
+ 0x016eeeee 0x51451400
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x00000066 0x00000000
+ 0x00000100 0x000e000e
+ 0x00000000 0x00000003
+ 0x0000d2b3 0x80000d22
+ 0x0000000a
+ >;
+ };
+
+ timing-300000000 {
+ clock-frequency = <300000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000000>;
+ nvidia,emc-cfg = <0x73340000>;
+ nvidia,emc-cfg-2 = <0x000008d5>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100002>;
+ nvidia,emc-mode-2 = <0x80200000>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80000321>;
+ nvidia,emc-mrs-wait-cnt = <0x0173000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+ nvidia,emc-xm2dqspadctrl2 = <0x01231339>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00020000>;
+
+ nvidia,emc-configuration = <
+ 0x0000000d 0x0000004d
+ 0x00000000 0x00000009
+ 0x00000003 0x00000004
+ 0x00000008 0x00000002
+ 0x00000009 0x00000003
+ 0x00000003 0x00000002
+ 0x00000002 0x00000000
+ 0x00000003 0x00000003
+ 0x00000005 0x00000002
+ 0x00000000 0x00000002
+ 0x00000007 0x00020000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000001
+ 0x0000000e 0x00000010
+ 0x00000012 0x000008e4
+ 0x00000000 0x00000239
+ 0x00000001 0x00000008
+ 0x00000001 0x00000000
+ 0x0000004b 0x0000000e
+ 0x00000052 0x00000200
+ 0x00000004 0x00000005
+ 0x00000004 0x00000008
+ 0x00000000 0x00000005
+ 0x00000005 0x00000924
+ 0x00000000 0x00000000
+ 0x00000000 0x104ab098
+ 0x002c00a0 0x00008000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00098000 0x00098000
+ 0x00000000 0x00098000
+ 0x00098000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00050000 0x00050000
+ 0x00050000 0x00050000
+ 0x00005000 0x00005000
+ 0x00005000 0x00005000
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000505 0x81f1f108
+ 0x07070004 0x00000000
+ 0x016eeeee 0x51451420
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x00000096 0x00000000
+ 0x00000100 0x0173000e
+ 0x00000000 0x00000003
+ 0x000052a3 0x800012d7
+ 0x00000009
+ >;
+ };
+
+ timing-396000000 {
+ clock-frequency = <396000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000000>;
+ nvidia,emc-cfg = <0x73340000>;
+ nvidia,emc-cfg-2 = <0x00000895>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100002>;
+ nvidia,emc-mode-2 = <0x80200000>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80000521>;
+ nvidia,emc-mrs-wait-cnt = <0x015b000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040008>;
+ nvidia,emc-xm2dqspadctrl2 = <0x01231339>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00020000>;
+
+ nvidia,emc-configuration = <
+ 0x00000011 0x00000066
+ 0x00000000 0x0000000c
+ 0x00000004 0x00000004
+ 0x00000008 0x00000002
+ 0x0000000a 0x00000004
+ 0x00000004 0x00000002
+ 0x00000002 0x00000000
+ 0x00000003 0x00000003
+ 0x00000005 0x00000002
+ 0x00000000 0x00000001
+ 0x00000008 0x00020000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x0000000f 0x00000010
+ 0x00000012 0x00000bd1
+ 0x00000000 0x000002f4
+ 0x00000001 0x00000008
+ 0x00000001 0x00000000
+ 0x00000063 0x0000000f
+ 0x0000006c 0x00000200
+ 0x00000004 0x00000005
+ 0x00000004 0x0000000b
+ 0x00000000 0x00000005
+ 0x00000005 0x00000c11
+ 0x00000000 0x00000000
+ 0x00000000 0x104ab098
+ 0x002c00a0 0x00008000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00030000 0x00030000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00070000 0x00070000
+ 0x00000000 0x00070000
+ 0x00070000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00038000 0x00038000
+ 0x00038000 0x00038000
+ 0x00003800 0x00003800
+ 0x00003800 0x00003800
+ 0x10000280 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc081
+ 0x00000505 0x81f1f108
+ 0x07070004 0x00000000
+ 0x016eeeee 0x51451420
+ 0x00514514 0x00514514
+ 0x51451400 0x0000003f
+ 0x000000c6 0x00000000
+ 0x00000100 0x015b000e
+ 0x00000000 0x00000003
+ 0x000052a3 0x8000188b
+ 0x00000009
+ >;
+ };
+
+ timing-528000000 {
+ clock-frequency = <528000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000000>;
+ nvidia,emc-cfg = <0x73300000>;
+ nvidia,emc-cfg-2 = <0x0000089d>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100002>;
+ nvidia,emc-mode-2 = <0x80200008>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80000941>;
+ nvidia,emc-mrs-wait-cnt = <0x0139000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040008>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0123133d>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00020000>;
+
+ nvidia,emc-configuration = <
+ 0x00000018 0x00000088
+ 0x00000000 0x00000010
+ 0x00000006 0x00000006
+ 0x00000009 0x00000002
+ 0x0000000d 0x00000006
+ 0x00000006 0x00000002
+ 0x00000002 0x00000000
+ 0x00000003 0x00000003
+ 0x00000006 0x00000002
+ 0x00000000 0x00000001
+ 0x00000009 0x00030000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000010 0x00000012
+ 0x00000014 0x00000fd6
+ 0x00000000 0x000003f5
+ 0x00000002 0x0000000b
+ 0x00000001 0x00000000
+ 0x00000085 0x00000012
+ 0x00000090 0x00000200
+ 0x00000004 0x00000005
+ 0x00000004 0x00000010
+ 0x00000000 0x00000006
+ 0x00000006 0x00001017
+ 0x00000000 0x00000000
+ 0x00000000 0x104ab098
+ 0xe01200b1 0x00008000
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00054000 0x00054000
+ 0x00000000 0x00054000
+ 0x00054000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x0000000c 0x0000000c
+ 0x0000000c 0x0000000c
+ 0x0000000c 0x0000000c
+ 0x0000000c 0x0000000c
+ 0x100002a0 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc085
+ 0x00000505 0x81f1f108
+ 0x07070004 0x00000000
+ 0x016eeeee 0x51451420
+ 0x00514514 0x00514514
+ 0x51451400 0x0606003f
+ 0x00000000 0x00000000
+ 0x00000100 0x0139000e
+ 0x00000000 0x00000003
+ 0x000042a0 0x80002062
+ 0x0000000a
+ >;
+ };
+
+ timing-600000000 {
+ clock-frequency = <600000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000000>;
+ nvidia,emc-cfg = <0x73300000>;
+ nvidia,emc-cfg-2 = <0x0000089d>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100002>;
+ nvidia,emc-mode-2 = <0x80200010>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80000b61>;
+ nvidia,emc-mrs-wait-cnt = <0x0127000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040008>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0121113d>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00020000>;
+
+ nvidia,emc-configuration = <
+ 0x0000001b 0x0000009b
+ 0x00000000 0x00000013
+ 0x00000007 0x00000007
+ 0x0000000b 0x00000003
+ 0x00000010 0x00000007
+ 0x00000007 0x00000002
+ 0x00000002 0x00000000
+ 0x00000005 0x00000005
+ 0x0000000a 0x00000002
+ 0x00000000 0x00000003
+ 0x0000000b 0x00070000
+ 0x00000003 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000002
+ 0x00000012 0x00000016
+ 0x00000018 0x00001208
+ 0x00000000 0x00000482
+ 0x00000002 0x0000000d
+ 0x00000001 0x00000000
+ 0x00000097 0x00000015
+ 0x000000a3 0x00000200
+ 0x00000004 0x00000005
+ 0x00000004 0x00000013
+ 0x00000000 0x00000006
+ 0x00000006 0x00001248
+ 0x00000000 0x00000000
+ 0x00000000 0x104ab098
+ 0xe00e00b1 0x00008000
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00048000 0x00048000
+ 0x00000000 0x00048000
+ 0x00048000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x0000000d 0x0000000d
+ 0x0000000d 0x0000000d
+ 0x0000000d 0x0000000d
+ 0x0000000d 0x0000000d
+ 0x100002a0 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc085
+ 0x00000505 0x81f1f108
+ 0x07070004 0x00000000
+ 0x016eeeee 0x51451420
+ 0x00514514 0x00514514
+ 0x51451400 0x0606003f
+ 0x00000000 0x00000000
+ 0x00000100 0x0127000e
+ 0x00000000 0x00000003
+ 0x000040a0 0x800024aa
+ 0x0000000e
+ >;
+ };
+
+ timing-792000000 {
+ clock-frequency = <792000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430000>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000000>;
+ nvidia,emc-cfg = <0x73300000>;
+ nvidia,emc-cfg-2 = <0x0000089d>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100002>;
+ nvidia,emc-mode-2 = <0x80200018>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80000d71>;
+ nvidia,emc-mrs-wait-cnt = <0x00f7000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040000>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0120113d>;
+ nvidia,emc-zcal-cnt-long = <0x00000042>;
+ nvidia,emc-zcal-interval = <0x00020000>;
+
+ nvidia,emc-configuration = <
+ 0x00000024 0x000000cd
+ 0x00000000 0x00000019
+ 0x0000000a 0x00000008
+ 0x0000000d 0x00000004
+ 0x00000013 0x0000000a
+ 0x0000000a 0x00000004
+ 0x00000002 0x00000000
+ 0x00000006 0x00000006
+ 0x0000000b 0x00000002
+ 0x00000000 0x00000002
+ 0x0000000d 0x00080000
+ 0x00000004 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000001
+ 0x00000014 0x00000018
+ 0x0000001a 0x000017e2
+ 0x00000000 0x000005f8
+ 0x00000003 0x00000011
+ 0x00000001 0x00000000
+ 0x000000c7 0x00000018
+ 0x000000d7 0x00000200
+ 0x00000005 0x00000006
+ 0x00000005 0x00000019
+ 0x00000000 0x00000008
+ 0x00000008 0x00001822
+ 0x00000000 0x00000000
+ 0x00000000 0x104ab098
+ 0xe00700b1 0x00008000
+ 0x007fc008 0x007fc008
+ 0x007fc008 0x007fc008
+ 0x007fc008 0x007fc008
+ 0x007fc008 0x007fc008
+ 0x007fc008 0x007fc008
+ 0x007fc008 0x007fc008
+ 0x007fc008 0x007fc008
+ 0x007fc008 0x007fc008
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00034000 0x00034000
+ 0x00000000 0x00034000
+ 0x00034000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000005 0x00000005
+ 0x00000005 0x00000005
+ 0x00000005 0x00000005
+ 0x00000005 0x00000005
+ 0x00000005 0x00000005
+ 0x00000005 0x00000005
+ 0x00000005 0x00000005
+ 0x00000005 0x00000005
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x0000000a 0x0000000a
+ 0x100002a0 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc085
+ 0x00000000 0x81f1f108
+ 0x07070004 0x00000000
+ 0x016eeeee 0x61861820
+ 0x00514514 0x00514514
+ 0x61861800 0x0606003f
+ 0x00000000 0x00000000
+ 0x00000100 0x00f7000e
+ 0x00000000 0x00000004
+ 0x00004080 0x80003012
+ 0x0000000f
+ >;
+ };
+
+ timing-924000000 {
+ clock-frequency = <924000000>;
+
+ nvidia,emc-auto-cal-config = <0xa1430303>;
+ nvidia,emc-auto-cal-config2 = <0x00000000>;
+ nvidia,emc-auto-cal-config3 = <0x00000000>;
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-bgbias-ctl0 = <0x00000000>;
+ nvidia,emc-cfg = <0x73300000>;
+ nvidia,emc-cfg-2 = <0x0000089d>;
+ nvidia,emc-ctt-term-ctrl = <0x00000802>;
+ nvidia,emc-mode-1 = <0x80100002>;
+ nvidia,emc-mode-2 = <0x80200020>;
+ nvidia,emc-mode-4 = <0x00000000>;
+ nvidia,emc-mode-reset = <0x80000f15>;
+ nvidia,emc-mrs-wait-cnt = <0x00cd000e>;
+ nvidia,emc-sel-dpd-ctrl = <0x00040000>;
+ nvidia,emc-xm2dqspadctrl2 = <0x0120113d>;
+ nvidia,emc-zcal-cnt-long = <0x0000004c>;
+ nvidia,emc-zcal-interval = <0x00020000>;
+
+ nvidia,emc-configuration = <
+ 0x0000002b 0x000000f0
+ 0x00000000 0x0000001e
+ 0x0000000b 0x00000009
+ 0x0000000f 0x00000005
+ 0x00000016 0x0000000b
+ 0x0000000b 0x00000004
+ 0x00000002 0x00000000
+ 0x00000007 0x00000007
+ 0x0000000d 0x00000002
+ 0x00000000 0x00000002
+ 0x0000000f 0x000a0000
+ 0x00000004 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000001
+ 0x00000016 0x0000001a
+ 0x0000001c 0x00001be7
+ 0x00000000 0x000006f9
+ 0x00000004 0x00000015
+ 0x00000001 0x00000000
+ 0x000000e7 0x0000001b
+ 0x000000fb 0x00000200
+ 0x00000006 0x00000007
+ 0x00000006 0x0000001e
+ 0x00000000 0x0000000a
+ 0x0000000a 0x00001c28
+ 0x00000000 0x00000000
+ 0x00000000 0x104ab898
+ 0xe00400b1 0x00008000
+ 0x007f800a 0x007f800a
+ 0x007f800a 0x007f800a
+ 0x007f800a 0x007f800a
+ 0x007f800a 0x007f800a
+ 0x007f800a 0x007f800a
+ 0x007f800a 0x007f800a
+ 0x007f800a 0x007f800a
+ 0x007f800a 0x007f800a
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x0002c000 0x0002c000
+ 0x00000000 0x0002c000
+ 0x0002c000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000000 0x00000000
+ 0x00000004 0x00000004
+ 0x00000004 0x00000004
+ 0x00000004 0x00000004
+ 0x00000004 0x00000004
+ 0x00000004 0x00000004
+ 0x00000004 0x00000004
+ 0x00000004 0x00000004
+ 0x00000004 0x00000004
+ 0x00000008 0x00000008
+ 0x00000008 0x00000008
+ 0x00000008 0x00000008
+ 0x00000008 0x00000008
+ 0x100002a0 0x00000000
+ 0x00111111 0x00000000
+ 0x00000000 0x77ffc085
+ 0x00000000 0x81f1f108
+ 0x07070004 0x00000000
+ 0x016eeeee 0x5d75d720
+ 0x00514514 0x00514514
+ 0x5d75d700 0x0606003f
+ 0x00000000 0x00000000
+ 0x00000128 0x00cd000e
+ 0x00000000 0x00000004
+ 0x00004080 0x800037ea
+ 0x00000011
+ >;
+ };
+
+ };
+ };
+
+ memory-controller@70019000 {
+ emc-timings-1 {
+ nvidia,ram-code = <1>;
+
+ timing-12750000 {
+ clock-frequency = <12750000>;
+
+ nvidia,emem-configuration = <
+ 0x40040001 0x8000000a
+ 0x00000001 0x00000001
+ 0x00000002 0x00000000
+ 0x00000002 0x00000001
+ 0x00000003 0x00000008
+ 0x00000003 0x00000002
+ 0x00000003 0x00000006
+ 0x06030203 0x000a0502
+ 0x77e30303 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-20400000 {
+ clock-frequency = <20400000>;
+
+ nvidia,emem-configuration = <
+ 0x40020001 0x80000012
+ 0x00000001 0x00000001
+ 0x00000002 0x00000000
+ 0x00000002 0x00000001
+ 0x00000003 0x00000008
+ 0x00000003 0x00000002
+ 0x00000003 0x00000006
+ 0x06030203 0x000a0502
+ 0x76230303 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-40800000 {
+ clock-frequency = <40800000>;
+
+ nvidia,emem-configuration = <
+ 0xa0000001 0x80000017
+ 0x00000001 0x00000001
+ 0x00000002 0x00000000
+ 0x00000002 0x00000001
+ 0x00000003 0x00000008
+ 0x00000003 0x00000002
+ 0x00000003 0x00000006
+ 0x06030203 0x000a0502
+ 0x74a30303 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-68000000 {
+ clock-frequency = <68000000>;
+
+ nvidia,emem-configuration = <
+ 0x00000001 0x8000001e
+ 0x00000001 0x00000001
+ 0x00000002 0x00000000
+ 0x00000002 0x00000001
+ 0x00000003 0x00000008
+ 0x00000003 0x00000002
+ 0x00000003 0x00000006
+ 0x06030203 0x000a0502
+ 0x74230403 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-102000000 {
+ clock-frequency = <102000000>;
+
+ nvidia,emem-configuration = <
+ 0x08000001 0x80000026
+ 0x00000001 0x00000001
+ 0x00000003 0x00000000
+ 0x00000002 0x00000001
+ 0x00000003 0x00000008
+ 0x00000003 0x00000002
+ 0x00000003 0x00000006
+ 0x06030203 0x000a0503
+ 0x73c30504 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-204000000 {
+ clock-frequency = <204000000>;
+
+ nvidia,emem-configuration = <
+ 0x01000003 0x80000040
+ 0x00000001 0x00000001
+ 0x00000004 0x00000002
+ 0x00000003 0x00000001
+ 0x00000003 0x00000008
+ 0x00000003 0x00000002
+ 0x00000004 0x00000006
+ 0x06040203 0x000a0504
+ 0x73840a05 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-300000000 {
+ clock-frequency = <300000000>;
+
+ nvidia,emem-configuration = <
+ 0x08000004 0x80000040
+ 0x00000001 0x00000002
+ 0x00000007 0x00000004
+ 0x00000004 0x00000001
+ 0x00000002 0x00000007
+ 0x00000002 0x00000002
+ 0x00000004 0x00000006
+ 0x06040202 0x000b0607
+ 0x77450e08 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-396000000 {
+ clock-frequency = <396000000>;
+
+ nvidia,emem-configuration = <
+ 0x0f000005 0x80000040
+ 0x00000001 0x00000002
+ 0x00000009 0x00000005
+ 0x00000006 0x00000001
+ 0x00000002 0x00000008
+ 0x00000002 0x00000002
+ 0x00000004 0x00000006
+ 0x06040202 0x000d0709
+ 0x7586120a 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-528000000 {
+ clock-frequency = <528000000>;
+
+ nvidia,emem-configuration = <
+ 0x0f000007 0x80000040
+ 0x00000002 0x00000003
+ 0x0000000c 0x00000007
+ 0x00000008 0x00000001
+ 0x00000002 0x00000009
+ 0x00000002 0x00000002
+ 0x00000005 0x00000006
+ 0x06050202 0x0010090c
+ 0x7428180d 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-600000000 {
+ clock-frequency = <600000000>;
+
+ nvidia,emem-configuration = <
+ 0x00000009 0x80000040
+ 0x00000003 0x00000004
+ 0x0000000e 0x00000009
+ 0x0000000a 0x00000001
+ 0x00000003 0x0000000b
+ 0x00000002 0x00000002
+ 0x00000005 0x00000007
+ 0x07050202 0x00130b0e
+ 0x73a91b0f 0x70000f03
+ 0x001f0000
+ >;
+ };
+
+ timing-792000000 {
+ clock-frequency = <792000000>;
+
+ nvidia,emem-configuration = <
+ 0x0e00000b 0x80000040
+ 0x00000004 0x00000005
+ 0x00000013 0x0000000c
+ 0x0000000d 0x00000002
+ 0x00000003 0x0000000c
+ 0x00000002 0x00000002
+ 0x00000006 0x00000008
+ 0x08060202 0x00170e13
+ 0x736c2414 0x70000f02
+ 0x001f0000
+ >;
+ };
+
+ timing-924000000 {
+ clock-frequency = <924000000>;
+
+ nvidia,emem-configuration = <
+ 0x0e00000d 0x80000040
+ 0x00000005 0x00000006
+ 0x00000016 0x0000000e
+ 0x0000000f 0x00000002
+ 0x00000004 0x0000000e
+ 0x00000002 0x00000002
+ 0x00000006 0x00000009
+ 0x09060202 0x001a1016
+ 0x734e2a17 0x70000f02
+ 0x001f0000
+ >;
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "tegra124-apalis.dtsi"
+
+/ {
+ model = "Toradex Apalis TK1 on Apalis Evaluation Board";
+ compatible = "toradex,apalis-tk1-eval", "toradex,apalis-tk1",
+ "nvidia,tegra124";
+
+ aliases {
+ rtc0 = "/i2c@7000c000/rtc@68";
+ rtc1 = "/i2c@7000d000/pmic@40";
+ rtc2 = "/rtc@7000e000";
+ serial0 = &uarta;
+ serial1 = &uartb;
+ serial2 = &uartc;
+ serial3 = &uartd;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ pcie-controller@01003000 {
+ pci@1,0 {
+ status = "okay";
+ };
+ };
+
+ host1x@50000000 {
+ hdmi@54280000 {
+ status = "okay";
+ };
+ };
+
+ /* Apalis UART1 */
+ serial@70006000 {
+ status = "okay";
+ };
+
+ /* Apalis UART2 */
+ serial@70006040 {
+ status = "okay";
+ };
+
+ /* Apalis UART3 */
+ serial@70006200 {
+ status = "okay";
+ };
+
+ /* Apalis UART4 */
+ serial@70006300 {
+ status = "okay";
+ };
+
+ pwm@7000a000 {
+ status = "okay";
+ };
+
+ /*
+ * GEN1_I2C: I2C1_SDA/SCL on MXM3 pin 209/211 (e.g. RTC on carrier
+ * board)
+ */
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ pcie-switch@58 {
+ compatible = "plx,pex8605";
+ reg = <0x58>;
+ };
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc@68 {
+ compatible = "st,m41t00";
+ reg = <0x68>;
+ };
+ };
+
+ /*
+ * GEN2_I2C: I2C2_SDA/SCL (DDC) on MXM3 pin 205/207 (e.g. display EDID)
+ */
+ hdmi_ddc: i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /*
+ * CAM_I2C: I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor
+ * on carrier board)
+ */
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* I2C4 (DDC): unused */
+
+ /* SPI1: Apalis SPI1 */
+ spi@7000d400 {
+ status = "okay";
+ spi-max-frequency = <50000000>;
+
+ spidev0: spidev@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+ };
+
+ /* SPI4: Apalis SPI2 */
+ spi@7000da00 {
+ status = "okay";
+ spi-max-frequency = <50000000>;
+
+ spidev1: spidev@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+ };
+
+ /* Apalis Serial ATA */
+ sata@70020000 {
+ status = "okay";
+ };
+
+ hda@70030000 {
+ status = "okay";
+ };
+
+ usb@70090000 {
+ status = "okay";
+ };
+
+ /* Apalis MMC1 */
+ sdhci@700b0000 {
+ status = "okay";
+ /* MMC1_CD# */
+ cd-gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vqmmc-supply = <&vddio_sdmmc1>;
+ };
+
+ /* Apalis SD1 */
+ sdhci@700b0400 {
+ status = "okay";
+ /*
+ * Don't use SD1_CD# aka SDMMC3_CLK_LB_OUT for now as it
+ * features some magic properties even though the external
+ * loopback is disabled and the internal loopback used as per
+ * SDMMC_VENDOR_MISC_CNTRL_0 register's SDMMC_SPARE1 bits being
+ * set to 0xfffd according to the TRM!
+ * cd-gpios = <&gpio TEGRA_GPIO(EE, 4) GPIO_ACTIVE_LOW>;
+ */
+ bus-width = <4>;
+ vqmmc-supply = <&vddio_sdmmc3>;
+ };
+
+ /* EHCI instance 0: USB1_DP/N -> USBO1_DP/N */
+ usb@7d000000 {
+ status = "okay";
+ dr_mode = "otg";
+ };
+
+ usb-phy@7d000000 {
+ status = "okay";
+ vbus-supply = <®_usbo1_vbus>;
+ };
+
+ /* EHCI instance 1: USB2_DP/N -> USBH2_DP/N */
+ usb@7d004000 {
+ status = "okay";
+ };
+
+ usb-phy@7d004000 {
+ status = "okay";
+ vbus-supply = <®_usbh_vbus>;
+ };
+
+ /* EHCI instance 2: USB3_DP/N -> USBH4_DP/N */
+ usb@7d008000 {
+ status = "okay";
+ };
+
+ usb-phy@7d008000 {
+ status = "okay";
+ vbus-supply = <®_usbh_vbus>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+
+ /* BKL1_PWM */
+ pwms = <&pwm 3 5000000>;
+ brightness-levels = <255 231 223 207 191 159 127 0>;
+ default-brightness-level = <6>;
+ /* BKL1_ON */
+ enable-gpios = <&gpio TEGRA_GPIO(BB, 5) GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wakeup {
+ label = "WAKE1_MICO";
+ gpios = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5V_SW";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ /* USBO1_EN */
+ reg_usbo1_vbus: regulator-usbo1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_USBO1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_5v0>;
+ };
+
+ /* USBH_EN */
+ reg_usbh_vbus: regulator-usbh-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_USBH(2A|2C|2D|3|4)";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_5v0>;
+ };
+};
--- /dev/null
+/*
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "tegra124.dtsi"
+#include "tegra124-apalis-emc.dtsi"
+
+/*
+ * Toradex Apalis TK1 Module Device Tree
+ * Compatible for Revisions 2GB: V1.0A
+ */
+/ {
+ model = "Toradex Apalis TK1";
+ compatible = "toradex,apalis-tk1", "nvidia,tegra124";
+
+ memory {
+ reg = <0x0 0x80000000 0x0 0x80000000>;
+ };
+
+ pcie-controller@01003000 {
+ status = "okay";
+
+ avddio-pex-supply = <&vdd_1v05>;
+ avdd-pex-pll-supply = <&vdd_1v05>;
+ avdd-pll-erefe-supply = <&avdd_1v05>;
+ dvddio-pex-supply = <&vdd_1v05>;
+ hvdd-pex-pll-e-supply = <®_3v3>;
+ hvdd-pex-supply = <®_3v3>;
+ vddio-pex-ctl-supply = <®_3v3>;
+
+ /* Apalis PCIe (additional lane Apalis type specific) */
+ pci@1,0 {
+ /* PCIE1_RX/TX and TS_DIFF1/2 */
+ phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>,
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>;
+ phy-names = "pcie-0", "pcie-1";
+ };
+
+ /* I210 Gigabit Ethernet Controller (On-module) */
+ pci@2,0 {
+ phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>;
+ phy-names = "pcie-0";
+ status = "okay";
+ };
+ };
+
+ host1x@50000000 {
+ hdmi@54280000 {
+ pll-supply = <®_1v05_avdd_hdmi_pll>;
+ vdd-supply = <®_3v3_avdd_hdmi>;
+
+ nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+ nvidia,hpd-gpio =
+ <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpu@0,57000000 {
+ /*
+ * Node left disabled on purpose - the bootloader will enable
+ * it after having set the VPR up
+ */
+ vdd-supply = <&vdd_gpu>;
+ };
+
+ pinmux: pinmux@70000868 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ /* Analogue Audio (On-module) */
+ dap3_fs_pp0 {
+ nvidia,pins = "dap3_fs_pp0";
+ nvidia,function = "i2s2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap3_din_pp1 {
+ nvidia,pins = "dap3_din_pp1";
+ nvidia,function = "i2s2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ dap3_dout_pp2 {
+ nvidia,pins = "dap3_dout_pp2";
+ nvidia,function = "i2s2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap3_sclk_pp3 {
+ nvidia,pins = "dap3_sclk_pp3";
+ nvidia,function = "i2s2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap_mclk1_pw4 {
+ nvidia,pins = "dap_mclk1_pw4";
+ nvidia,function = "extperiph1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis BKL1_ON */
+ pbb5 {
+ nvidia,pins = "pbb5";
+ nvidia,function = "vgp5";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis BKL1_PWM */
+ pu6 {
+ nvidia,pins = "pu6";
+ nvidia,function = "pwm3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis CAM1_MCLK */
+ cam_mclk_pcc0 {
+ nvidia,pins = "cam_mclk_pcc0";
+ nvidia,function = "vi_alt3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis Digital Audio */
+ dap2_fs_pa2 {
+ nvidia,pins = "dap2_fs_pa2";
+ nvidia,function = "hda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ dap2_sclk_pa3 {
+ nvidia,pins = "dap2_sclk_pa3";
+ nvidia,function = "hda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ dap2_din_pa4 {
+ nvidia,pins = "dap2_din_pa4";
+ nvidia,function = "hda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ dap2_dout_pa5 {
+ nvidia,pins = "dap2_dout_pa5";
+ nvidia,function = "hda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pbb3 { /* DAP1_RESET */
+ nvidia,pins = "pbb3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ clk3_out_pee0 {
+ nvidia,pins = "clk3_out_pee0";
+ nvidia,function = "extperiph3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis GPIO */
+ ddc_scl_pv4 {
+ nvidia,pins = "ddc_scl_pv4";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ ddc_sda_pv5 {
+ nvidia,pins = "ddc_sda_pv5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ pex_l0_rst_n_pdd1 {
+ nvidia,pins = "pex_l0_rst_n_pdd1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ pex_l0_clkreq_n_pdd2 {
+ nvidia,pins = "pex_l0_clkreq_n_pdd2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ pex_l1_rst_n_pdd5 {
+ nvidia,pins = "pex_l1_rst_n_pdd5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ pex_l1_clkreq_n_pdd6 {
+ nvidia,pins = "pex_l1_clkreq_n_pdd6";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ dp_hpd_pff0 {
+ nvidia,pins = "dp_hpd_pff0";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ pff2 {
+ nvidia,pins = "pff2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ owr { /* PEX_L1_CLKREQ_N multiplexed GPIO6 */
+ nvidia,pins = "owr";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ nvidia,rcv-sel = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis HDMI1_CEC */
+ hdmi_cec_pee3 {
+ nvidia,pins = "hdmi_cec_pee3";
+ nvidia,function = "cec";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis HDMI1_HPD */
+ hdmi_int_pn7 {
+ nvidia,pins = "hdmi_int_pn7";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,rcv-sel = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis I2C1 */
+ gen1_i2c_scl_pc4 {
+ nvidia,pins = "gen1_i2c_scl_pc4";
+ nvidia,function = "i2c1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+ gen1_i2c_sda_pc5 {
+ nvidia,pins = "gen1_i2c_sda_pc5";
+ nvidia,function = "i2c1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis I2C2 (DDC) */
+ gen2_i2c_scl_pt5 {
+ nvidia,pins = "gen2_i2c_scl_pt5";
+ nvidia,function = "i2c2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+ gen2_i2c_sda_pt6 {
+ nvidia,pins = "gen2_i2c_sda_pt6";
+ nvidia,function = "i2c2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis I2C3 (CAM) */
+ cam_i2c_scl_pbb1 {
+ nvidia,pins = "cam_i2c_scl_pbb1";
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+ cam_i2c_sda_pbb2 {
+ nvidia,pins = "cam_i2c_sda_pbb2";
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis MMC1 */
+ sdmmc1_cd_n_pv3 { /* CD# GPIO */
+ nvidia,pins = "sdmmc1_wp_n_pv3";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ clk2_out_pw5 { /* D5 GPIO */
+ nvidia,pins = "clk2_out_pw5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc1_dat3_py4 {
+ nvidia,pins = "sdmmc1_dat3_py4";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc1_dat2_py5 {
+ nvidia,pins = "sdmmc1_dat2_py5";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc1_dat1_py6 {
+ nvidia,pins = "sdmmc1_dat1_py6";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc1_dat0_py7 {
+ nvidia,pins = "sdmmc1_dat0_py7";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc1_clk_pz0 {
+ nvidia,pins = "sdmmc1_clk_pz0";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc1_cmd_pz1 {
+ nvidia,pins = "sdmmc1_cmd_pz1";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ clk2_req_pcc5 { /* D4 GPIO */
+ nvidia,pins = "clk2_req_pcc5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /*
+ * Don't use MMC1_D6 aka SDMMC3_CLK_LB_IN for now as it
+ * features some magic properties even though the
+ * external loopback is disabled and the internal
+ * loopback used as per SDMMC_VENDOR_MISC_CNTRL_0
+ * register's SDMMC_SPARE1 bits being set to 0xfffd
+ * according to the TRM!
+ */
+ sdmmc3_clk_lb_in_pee5 { /* D6 GPIO */
+ nvidia,pins = "sdmmc3_clk_lb_in_pee5";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ usb_vbus_en2_pff1 { /* D7 GPIO */
+ nvidia,pins = "usb_vbus_en2_pff1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis PWM */
+ ph0 {
+ nvidia,pins = "ph0";
+ nvidia,function = "pwm0";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ph1 {
+ nvidia,pins = "ph1";
+ nvidia,function = "pwm1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ph2 {
+ nvidia,pins = "ph2";
+ nvidia,function = "pwm2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ /* PWM3 active on pu6 being Apalis BKL1_PWM */
+ ph3 {
+ nvidia,pins = "ph3";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis SATA1_ACT# */
+ dap1_dout_pn2 {
+ nvidia,pins = "dap1_dout_pn2";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis SD1 */
+ sdmmc3_clk_pa6 {
+ nvidia,pins = "sdmmc3_clk_pa6";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc3_cmd_pa7 {
+ nvidia,pins = "sdmmc3_cmd_pa7";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc3_dat3_pb4 {
+ nvidia,pins = "sdmmc3_dat3_pb4";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc3_dat2_pb5 {
+ nvidia,pins = "sdmmc3_dat2_pb5";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc3_dat1_pb6 {
+ nvidia,pins = "sdmmc3_dat1_pb6";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc3_dat0_pb7 {
+ nvidia,pins = "sdmmc3_dat0_pb7";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /*
+ * Don't use SD1_CD# aka SDMMC3_CLK_LB_OUT for now as it
+ * features some magic properties even though the
+ * external loopback is disabled and the internal
+ * loopback used as per SDMMC_VENDOR_MISC_CNTRL_0
+ * register's SDMMC_SPARE1 bits being set to 0xfffd
+ * according to the TRM!
+ */
+ sdmmc3_clk_lb_out_pee4 { /* CD# GPIO */
+ nvidia,pins = "sdmmc3_clk_lb_out_pee4";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis SPDIF */
+ spdif_out_pk5 {
+ nvidia,pins = "spdif_out_pk5";
+ nvidia,function = "spdif";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ spdif_in_pk6 {
+ nvidia,pins = "spdif_in_pk6";
+ nvidia,function = "spdif";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis SPI1 */
+ ulpi_clk_py0 {
+ nvidia,pins = "ulpi_clk_py0";
+ nvidia,function = "spi1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_dir_py1 {
+ nvidia,pins = "ulpi_dir_py1";
+ nvidia,function = "spi1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ ulpi_nxt_py2 {
+ nvidia,pins = "ulpi_nxt_py2";
+ nvidia,function = "spi1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_stp_py3 {
+ nvidia,pins = "ulpi_stp_py3";
+ nvidia,function = "spi1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis SPI2 */
+ pg5 {
+ nvidia,pins = "pg5";
+ nvidia,function = "spi4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pg6 {
+ nvidia,pins = "pg6";
+ nvidia,function = "spi4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pg7 {
+ nvidia,pins = "pg7";
+ nvidia,function = "spi4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ pi3 {
+ nvidia,pins = "pi3";
+ nvidia,function = "spi4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis UART1 */
+ pb1 { /* DCD GPIO */
+ nvidia,pins = "pb1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ pk7 { /* RI GPIO */
+ nvidia,pins = "pk7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ uart1_txd_pu0 {
+ nvidia,pins = "pu0";
+ nvidia,function = "uarta";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ uart1_rxd_pu1 {
+ nvidia,pins = "pu1";
+ nvidia,function = "uarta";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ uart1_cts_n_pu2 {
+ nvidia,pins = "pu2";
+ nvidia,function = "uarta";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ uart1_rts_n_pu3 {
+ nvidia,pins = "pu3";
+ nvidia,function = "uarta";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ uart3_cts_n_pa1 { /* DSR GPIO */
+ nvidia,pins = "uart3_cts_n_pa1";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ uart3_rts_n_pc0 { /* DTR GPIO */
+ nvidia,pins = "uart3_rts_n_pc0";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis UART2 */
+ uart2_txd_pc2 {
+ nvidia,pins = "uart2_txd_pc2";
+ nvidia,function = "irda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ uart2_rxd_pc3 {
+ nvidia,pins = "uart2_rxd_pc3";
+ nvidia,function = "irda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ uart2_cts_n_pj5 {
+ nvidia,pins = "uart2_cts_n_pj5";
+ nvidia,function = "uartb";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ uart2_rts_n_pj6 {
+ nvidia,pins = "uart2_rts_n_pj6";
+ nvidia,function = "uartb";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis UART3 */
+ uart3_txd_pw6 {
+ nvidia,pins = "uart3_txd_pw6";
+ nvidia,function = "uartc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ uart3_rxd_pw7 {
+ nvidia,pins = "uart3_rxd_pw7";
+ nvidia,function = "uartc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis UART4 */
+ uart4_rxd_pb0 {
+ nvidia,pins = "pb0";
+ nvidia,function = "uartd";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ uart4_txd_pj7 {
+ nvidia,pins = "pj7";
+ nvidia,function = "uartd";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis USBH_EN */
+ usb_vbus_en1_pn5 {
+ nvidia,pins = "usb_vbus_en1_pn5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis USBH_OC# */
+ pbb0 {
+ nvidia,pins = "pbb0";
+ nvidia,function = "vgp6";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis USBO1_EN */
+ usb_vbus_en0_pn4 {
+ nvidia,pins = "usb_vbus_en0_pn4";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis USBO1_OC# */
+ pbb4 {
+ nvidia,pins = "pbb4";
+ nvidia,function = "vgp4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis WAKE1_MICO */
+ pex_wake_n_pdd3 {
+ nvidia,pins = "pex_wake_n_pdd3";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* CORE_PWR_REQ */
+ core_pwr_req {
+ nvidia,pins = "core_pwr_req";
+ nvidia,function = "pwron";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* CPU_PWR_REQ */
+ cpu_pwr_req {
+ nvidia,pins = "cpu_pwr_req";
+ nvidia,function = "cpu";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* DVFS */
+ dvfs_pwm_px0 {
+ nvidia,pins = "dvfs_pwm_px0";
+ nvidia,function = "cldvfs";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dvfs_clk_px2 {
+ nvidia,pins = "dvfs_clk_px2";
+ nvidia,function = "cldvfs";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* eMMC */
+ sdmmc4_dat0_paa0 {
+ nvidia,pins = "sdmmc4_dat0_paa0";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_dat1_paa1 {
+ nvidia,pins = "sdmmc4_dat1_paa1";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_dat2_paa2 {
+ nvidia,pins = "sdmmc4_dat2_paa2";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_dat3_paa3 {
+ nvidia,pins = "sdmmc4_dat3_paa3";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_dat4_paa4 {
+ nvidia,pins = "sdmmc4_dat4_paa4";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_dat5_paa5 {
+ nvidia,pins = "sdmmc4_dat5_paa5";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_dat6_paa6 {
+ nvidia,pins = "sdmmc4_dat6_paa6";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_dat7_paa7 {
+ nvidia,pins = "sdmmc4_dat7_paa7";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_clk_pcc4 {
+ nvidia,pins = "sdmmc4_clk_pcc4";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4_cmd_pt7 {
+ nvidia,pins = "sdmmc4_cmd_pt7";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* JTAG_RTCK */
+ jtag_rtck {
+ nvidia,pins = "jtag_rtck";
+ nvidia,function = "rtck";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* LAN_DEV_OFF# */
+ ulpi_data5_po6 {
+ nvidia,pins = "ulpi_data5_po6";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* LAN_RESET# */
+ kb_row10_ps2 {
+ nvidia,pins = "kb_row10_ps2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* LAN_WAKE# */
+ ulpi_data4_po5 {
+ nvidia,pins = "ulpi_data4_po5";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* MCU_INT1# */
+ pk2 {
+ nvidia,pins = "pk2";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* MCU_INT2# */
+ pj2 {
+ nvidia,pins = "pj2";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* MCU_INT3# */
+ pi5 {
+ nvidia,pins = "pi5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* MCU_INT4# */
+ pj0 {
+ nvidia,pins = "pj0";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* MCU_RESET */
+ pbb6 {
+ nvidia,pins = "pbb6";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* MCU SPI */
+ gpio_x4_aud_px4 {
+ nvidia,pins = "gpio_x4_aud_px4";
+ nvidia,function = "spi2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gpio_x5_aud_px5 {
+ nvidia,pins = "gpio_x5_aud_px5";
+ nvidia,function = "spi2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gpio_x6_aud_px6 { /* MCU_CS */
+ nvidia,pins = "gpio_x6_aud_px6";
+ nvidia,function = "spi2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gpio_x7_aud_px7 {
+ nvidia,pins = "gpio_x7_aud_px7";
+ nvidia,function = "spi2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ gpio_w2_aud_pw2 { /* MCU_CSEZP */
+ nvidia,pins = "gpio_w2_aud_pw2";
+ nvidia,function = "spi2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* PMIC_CLK_32K */
+ clk_32k_in {
+ nvidia,pins = "clk_32k_in";
+ nvidia,function = "clk";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* PMIC_CPU_OC_INT */
+ clk_32k_out_pa0 {
+ nvidia,pins = "clk_32k_out_pa0";
+ nvidia,function = "soc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* PWR_I2C */
+ pwr_i2c_scl_pz6 {
+ nvidia,pins = "pwr_i2c_scl_pz6";
+ nvidia,function = "i2cpwr";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+ pwr_i2c_sda_pz7 {
+ nvidia,pins = "pwr_i2c_sda_pz7";
+ nvidia,function = "i2cpwr";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* PWR_INT_N */
+ pwr_int_n {
+ nvidia,pins = "pwr_int_n";
+ nvidia,function = "pmi";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* RESET_MOCI_CTRL */
+ pu4 {
+ nvidia,pins = "pu4";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* RESET_OUT_N */
+ reset_out_n {
+ nvidia,pins = "reset_out_n";
+ nvidia,function = "reset_out_n";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* SHIFT_CTRL_DIR_IN */
+ kb_row0_pr0 {
+ nvidia,pins = "kb_row0_pr0";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row1_pr1 {
+ nvidia,pins = "kb_row1_pr1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Configure level-shifter as output for HDA */
+ kb_row11_ps3 {
+ nvidia,pins = "kb_row11_ps3";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* SHIFT_CTRL_DIR_OUT */
+ kb_col5_pq5 {
+ nvidia,pins = "kb_col5_pq5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_col6_pq6 {
+ nvidia,pins = "kb_col6_pq6";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_col7_pq7 {
+ nvidia,pins = "kb_col7_pq7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* SHIFT_CTRL_OE */
+ kb_col0_pq0 {
+ nvidia,pins = "kb_col0_pq0";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_col1_pq1 {
+ nvidia,pins = "kb_col1_pq1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_col2_pq2 {
+ nvidia,pins = "kb_col2_pq2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_col4_pq4 {
+ nvidia,pins = "kb_col4_pq4";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row2_pr2 {
+ nvidia,pins = "kb_row2_pr2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* GPIO_PI6 aka TEMP_ALERT_L */
+ pi6 {
+ nvidia,pins = "pi6";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* TOUCH_INT */
+ gpio_w3_aud_pw3 {
+ nvidia,pins = "gpio_w3_aud_pw3";
+ nvidia,function = "spi6";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ pc7 { /* NC */
+ nvidia,pins = "pc7";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pg0 { /* NC */
+ nvidia,pins = "pg0";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pg1 { /* NC */
+ nvidia,pins = "pg1";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pg2 { /* NC */
+ nvidia,pins = "pg2";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pg3 { /* NC */
+ nvidia,pins = "pg3";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pg4 { /* NC */
+ nvidia,pins = "pg4";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ph4 { /* NC */
+ nvidia,pins = "ph4";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ph5 { /* NC */
+ nvidia,pins = "ph5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ph6 { /* NC */
+ nvidia,pins = "ph6";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ph7 { /* NC */
+ nvidia,pins = "ph7";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pi0 { /* NC */
+ nvidia,pins = "pi0";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pi1 { /* NC */
+ nvidia,pins = "pi1";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pi2 { /* NC */
+ nvidia,pins = "pi2";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pi4 { /* NC */
+ nvidia,pins = "pi4";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pi7 { /* NC */
+ nvidia,pins = "pi7";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pk0 { /* NC */
+ nvidia,pins = "pk0";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pk1 { /* NC */
+ nvidia,pins = "pk1";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pk3 { /* NC */
+ nvidia,pins = "pk3";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pk4 { /* NC */
+ nvidia,pins = "pk4";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap1_fs_pn0 { /* NC */
+ nvidia,pins = "dap1_fs_pn0";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap1_din_pn1 { /* NC */
+ nvidia,pins = "dap1_din_pn1";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap1_sclk_pn3 { /* NC */
+ nvidia,pins = "dap1_sclk_pn3";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_data7_po0 { /* NC */
+ nvidia,pins = "ulpi_data7_po0";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_data0_po1 { /* NC */
+ nvidia,pins = "ulpi_data0_po1";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_data1_po2 { /* NC */
+ nvidia,pins = "ulpi_data1_po2";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_data2_po3 { /* NC */
+ nvidia,pins = "ulpi_data2_po3";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_data3_po4 { /* NC */
+ nvidia,pins = "ulpi_data3_po4";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ ulpi_data6_po7 { /* NC */
+ nvidia,pins = "ulpi_data6_po7";
+ nvidia,function = "ulpi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap4_fs_pp4 { /* NC */
+ nvidia,pins = "dap4_fs_pp4";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap4_din_pp5 { /* NC */
+ nvidia,pins = "dap4_din_pp5";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap4_dout_pp6 { /* NC */
+ nvidia,pins = "dap4_dout_pp6";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap4_sclk_pp7 { /* NC */
+ nvidia,pins = "dap4_sclk_pp7";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_col3_pq3 { /* NC */
+ nvidia,pins = "kb_col3_pq3";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row3_pr3 { /* NC */
+ nvidia,pins = "kb_row3_pr3";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row4_pr4 { /* NC */
+ nvidia,pins = "kb_row4_pr4";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row5_pr5 { /* NC */
+ nvidia,pins = "kb_row5_pr5";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row6_pr6 { /* NC */
+ nvidia,pins = "kb_row6_pr6";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row7_pr7 { /* NC */
+ nvidia,pins = "kb_row7_pr7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row8_ps0 { /* NC */
+ nvidia,pins = "kb_row8_ps0";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row9_ps1 { /* NC */
+ nvidia,pins = "kb_row9_ps1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row12_ps4 { /* NC */
+ nvidia,pins = "kb_row12_ps4";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row13_ps5 { /* NC */
+ nvidia,pins = "kb_row13_ps5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row14_ps6 { /* NC */
+ nvidia,pins = "kb_row14_ps6";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row15_ps7 { /* NC */
+ nvidia,pins = "kb_row15_ps7";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row16_pt0 { /* NC */
+ nvidia,pins = "kb_row16_pt0";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb_row17_pt1 { /* NC */
+ nvidia,pins = "kb_row17_pt1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pu5 { /* NC */
+ nvidia,pins = "pu5";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pv0 { /* NC */
+ nvidia,pins = "pv0";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pv1 { /* NC */
+ nvidia,pins = "pv1";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ sdmmc3_cd_n_pv2 { /* NC */
+ nvidia,pins = "sdmmc3_cd_n_pv2";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gpio_x1_aud_px1 { /* NC */
+ nvidia,pins = "gpio_x1_aud_px1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gpio_x3_aud_px3 { /* NC */
+ nvidia,pins = "gpio_x3_aud_px3";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pbb7 { /* NC */
+ nvidia,pins = "pbb7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pcc1 { /* NC */
+ nvidia,pins = "pcc1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pcc2 { /* NC */
+ nvidia,pins = "pcc2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ clk3_req_pee1 { /* NC */
+ nvidia,pins = "clk3_req_pee1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap_mclk1_req_pee2 { /* NC */
+ nvidia,pins = "dap_mclk1_req_pee2";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ };
+ };
+
+ serial@70006040 {
+ compatible = "nvidia,tegra124-hsuart";
+ };
+
+ serial@70006200 {
+ compatible = "nvidia,tegra124-hsuart";
+ };
+
+ serial@70006300 {
+ compatible = "nvidia,tegra124-hsuart";
+ };
+
+ hdmi_ddc: i2c@7000c400 {
+ clock-frequency = <100000>;
+ };
+
+ /* PWR_I2C: power I2C to audio codec, PMIC and temperature sensor */
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* SGTL5000 audio codec */
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <&vddio_1v8>;
+ clocks = <&tegra_car TEGRA124_CLK_EXTERN1>;
+ };
+
+ pmic: pmic@40 {
+ compatible = "ams,as3722";
+ reg = <0x40>;
+ interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
+
+ ams,system-power-controller;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&as3722_default>;
+
+ as3722_default: pinmux {
+ gpio2_7 {
+ pins = "gpio2", /* PWR_EN_+V3.3 */
+ "gpio7"; /* +V1.6_LPO */
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ gpio1_3_4_5_6 {
+ pins = "gpio1", "gpio3", "gpio4",
+ "gpio5", "gpio6";
+ bias-high-impedance;
+ };
+ };
+
+ regulators {
+ vsup-sd2-supply = <®_3v3>;
+ vsup-sd3-supply = <®_3v3>;
+ vsup-sd4-supply = <®_3v3>;
+ vsup-sd5-supply = <®_3v3>;
+ vin-ldo0-supply = <&vddio_ddr_1v35>;
+ vin-ldo1-6-supply = <®_3v3>;
+ vin-ldo2-5-7-supply = <&vddio_1v8>;
+ vin-ldo3-4-supply = <®_3v3>;
+ vin-ldo9-10-supply = <®_3v3>;
+ vin-ldo11-supply = <®_3v3>;
+
+ vdd_cpu: sd0 {
+ regulator-name = "+VDD_CPU_AP";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-min-microamp = <3500000>;
+ regulator-max-microamp = <3500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ams,ext-control = <2>;
+ };
+
+ sd1 {
+ regulator-name = "+VDD_CORE";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-min-microamp = <2500000>;
+ regulator-max-microamp = <4000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ams,ext-control = <1>;
+ };
+
+ vddio_ddr_1v35: sd2 {
+ regulator-name =
+ "+V1.35_VDDIO_DDR(sd2)";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ sd3 {
+ regulator-name =
+ "+V1.35_VDDIO_DDR(sd3)";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_1v05: sd4 {
+ regulator-name = "+V1.05";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ vddio_1v8: sd5 {
+ regulator-name = "+V1.8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd_gpu: sd6 {
+ regulator-name = "+VDD_GPU_AP";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-min-microamp = <3500000>;
+ regulator-max-microamp = <3500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ avdd_1v05: ldo0 {
+ regulator-name = "+V1.05_AVDD";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ams,ext-control = <1>;
+ };
+
+ vddio_sdmmc1: ldo1 {
+ regulator-name = "VDDIO_SDMMC1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo2 {
+ regulator-name = "+V1.2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3 {
+ regulator-name = "+V1.05_RTC";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ams,enable-tracking;
+ };
+
+ /* 1.8V for LVDS, 3.3V for eDP */
+ ldo4 {
+ regulator-name = "AVDD_LVDS0_PLL";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /* LDO5 not used */
+
+ vddio_sdmmc3: ldo6 {
+ regulator-name = "VDDIO_SDMMC3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ /* LDO7 not used */
+
+ ldo9 {
+ regulator-name = "+V3.3_ETH(ldo9)";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo10 {
+ regulator-name = "+V3.3_ETH(ldo10)";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo11 {
+ regulator-name = "+V1.8_VPP_FUSE";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+
+ /*
+ * TMP451 temperature sensor
+ * Note: THERM_N directly connected to AS3722 PMIC THERM
+ */
+ temperature-sensor@4c {
+ compatible = "ti,tmp451";
+ reg = <0x4c>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
+ /* SPI2: MCU SPI */
+ spi@7000d600 {
+ status = "okay";
+ spi-max-frequency = <25000000>;
+ };
+
+ pmc@7000e400 {
+ nvidia,invert-interrupt;
+ nvidia,suspend-mode = <1>;
+ nvidia,cpu-pwr-good-time = <500>;
+ nvidia,cpu-pwr-off-time = <300>;
+ nvidia,core-pwr-good-time = <641 3845>;
+ nvidia,core-pwr-off-time = <61036>;
+ nvidia,core-power-req-active-high;
+ nvidia,sys-clock-req-active-high;
+
+ /* Set power_off bit in ResetControl register of AS3722 PMIC */
+ i2c-thermtrip {
+ nvidia,i2c-controller-id = <4>;
+ nvidia,bus-addr = <0x40>;
+ nvidia,reg-addr = <0x36>;
+ nvidia,reg-data = <0x2>;
+ };
+ };
+
+ sata@70020000 {
+ phys = <&{/padctl@7009f000/pads/sata/lanes/sata-0}>;
+ phy-names = "sata-0";
+
+ avdd-supply = <&vdd_1v05>;
+ hvdd-supply = <®_3v3>;
+ vddio-supply = <&vdd_1v05>;
+ };
+
+ usb@70090000 {
+ /* USBO1, USBO1 (SS), USBH2, USBH4 and USBH4 (SS) */
+ phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>,
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>,
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>,
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>,
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>;
+ phy-names = "usb2-0", "usb3-1", "usb2-1", "usb2-2", "usb3-0";
+
+ avddio-pex-supply = <&vdd_1v05>;
+ avdd-pll-erefe-supply = <&avdd_1v05>;
+ avdd-pll-utmip-supply = <&vddio_1v8>;
+ avdd-usb-ss-pll-supply = <&vdd_1v05>;
+ avdd-usb-supply = <®_3v3>;
+ dvddio-pex-supply = <&vdd_1v05>;
+ hvdd-usb-ss-pll-e-supply = <®_3v3>;
+ hvdd-usb-ss-supply = <®_3v3>;
+ };
+
+ padctl@7009f000 {
+ pads {
+ usb2 {
+ status = "okay";
+
+ lanes {
+ usb2-0 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+
+ usb2-1 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+
+ usb2-2 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+ };
+ };
+
+ pcie {
+ status = "okay";
+
+ lanes {
+ pcie-0 {
+ nvidia,function = "usb3-ss";
+ status = "okay";
+ };
+
+ pcie-1 {
+ nvidia,function = "usb3-ss";
+ status = "okay";
+ };
+
+ pcie-2 {
+ nvidia,function = "pcie";
+ status = "okay";
+ };
+
+ pcie-3 {
+ nvidia,function = "pcie";
+ status = "okay";
+ };
+
+ pcie-4 {
+ nvidia,function = "pcie";
+ status = "okay";
+ };
+ };
+ };
+
+ sata {
+ status = "okay";
+
+ lanes {
+ sata-0 {
+ nvidia,function = "sata";
+ status = "okay";
+ };
+ };
+ };
+ };
+
+ ports {
+ /* USBO1 */
+ usb2-0 {
+ status = "okay";
+ mode = "otg";
+
+ vbus-supply = <®_usbo1_vbus>;
+ };
+
+ /* USBH2 */
+ usb2-1 {
+ status = "okay";
+ mode = "host";
+
+ vbus-supply = <®_usbh_vbus>;
+ };
+
+ /* USBH4 */
+ usb2-2 {
+ status = "okay";
+ mode = "host";
+
+ vbus-supply = <®_usbh_vbus>;
+ };
+
+ usb3-0 {
+ nvidia,usb2-companion = <2>;
+ status = "okay";
+ };
+
+ usb3-1 {
+ nvidia,usb2-companion = <0>;
+ status = "okay";
+ };
+ };
+ };
+
+ /* eMMC */
+ sdhci@700b0600 {
+ status = "okay";
+ bus-width = <8>;
+ non-removable;
+ };
+
+ /* CPU DFLL clock */
+ clock@70110000 {
+ status = "okay";
+ vdd-cpu-supply = <&vdd_cpu>;
+ nvidia,i2c-fs-rate = <400000>;
+ };
+
+ ahub@70300000 {
+ i2s@70301200 {
+ status = "okay";
+ };
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clk32k_in: clock@0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ cpus {
+ cpu@0 {
+ vdd-cpu-supply = <&vdd_cpu>;
+ };
+ };
+
+ reg_1v05_avdd_hdmi_pll: regulator-1v05-avdd-hdmi-pll {
+ compatible = "regulator-fixed";
+ regulator-name = "+V1.05_AVDD_HDMI_PLL";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+ vin-supply = <&vdd_1v05>;
+ };
+
+ reg_3v3_mxm: regulator-3v3-mxm {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3_MXM";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ /* PWR_EN_+V3.3 */
+ gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_3v3_mxm>;
+ };
+
+ reg_3v3_avdd_hdmi: regulator-3v3-avdd-hdmi {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3_AVDD_HDMI";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vdd_1v05>;
+ };
+
+ sound {
+ compatible = "toradex,tegra-audio-sgtl5000-apalis_tk1",
+ "nvidia,tegra-audio-sgtl5000";
+ nvidia,model = "Toradex Apalis TK1";
+ nvidia,audio-routing =
+ "Headphone Jack", "HP_OUT",
+ "LINE_IN", "Line In Jack",
+ "MIC_IN", "Mic Jack";
+ nvidia,i2s-controller = <&tegra_i2s2>;
+ nvidia,audio-codec = <&sgtl5000>;
+ clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
+ <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+ <&tegra_car TEGRA124_CLK_EXTERN1>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
+ };
+
+ thermal-zones {
+ cpu {
+ trips {
+ trip@0 {
+ temperature = <101000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ /*
+ * There are currently no cooling maps because
+ * there are no cooling devices
+ */
+ };
+ };
+
+ mem {
+ trips {
+ trip@0 {
+ temperature = <101000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ /*
+ * There are currently no cooling maps because
+ * there are no cooling devices
+ */
+ };
+ };
+
+ gpu {
+ trips {
+ trip@0 {
+ temperature = <101000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ /*
+ * There are currently no cooling maps because
+ * there are no cooling devices
+ */
+ };
+ };
+ };
+};
/ {
- clock@0,60006000 {
+ clock@60006000 {
emc-timings-3 {
nvidia,ram-code = <3>;
};
};
- emc@0,7001b000 {
+ emc@7001b000 {
emc-timings-3 {
nvidia,ram-code = <3>;
};
};
- memory-controller@0,70019000 {
+ memory-controller@70019000 {
emc-timings-3 {
nvidia,ram-code = <3>;
compatible = "nvidia,jetson-tk1", "nvidia,tegra124";
aliases {
- rtc0 = "/i2c@0,7000d000/pmic@40";
- rtc1 = "/rtc@0,7000e000";
+ rtc0 = "/i2c@7000d000/pmic@40";
+ rtc1 = "/rtc@7000e000";
/* This order keeps the mapping DB9 connector <-> ttyS0 */
serial0 = &uartd;
reg = <0x0 0x80000000 0x0 0x80000000>;
};
- pcie-controller@0,01003000 {
+ pcie-controller@01003000 {
status = "okay";
avddio-pex-supply = <&vdd_1v05_run>;
/* Mini PCIe */
pci@1,0 {
- phys = <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-4}>;
+ phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>;
phy-names = "pcie-0";
status = "okay";
};
/* Gigabit Ethernet */
pci@2,0 {
- phys = <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-2}>;
+ phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>;
phy-names = "pcie-0";
status = "okay";
};
};
- host1x@0,50000000 {
- hdmi@0,54280000 {
+ host1x@50000000 {
+ hdmi@54280000 {
status = "okay";
hdmi-supply = <&vdd_5v0_hdmi>;
vdd-supply = <&vdd_gpu>;
};
- pinmux: pinmux@0,70000868 {
+ pinmux: pinmux@70000868 {
pinctrl-names = "boot";
pinctrl-0 = <&state_boot>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
- owr {
- nvidia,pins = "owr";
- nvidia,function = "rsvd2";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,rcv-sel = <TEGRA_PIN_DISABLE>;
- };
clk_32k_in {
nvidia,pins = "clk_32k_in";
nvidia,function = "clk";
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
+ dsi_b {
+ nvidia,pins = "mipi_pad_ctrl_dsi_b";
+ nvidia,function = "dsi_b";
+ };
};
};
};
/* DB9 serial port */
- serial@0,70006300 {
+ serial@70006300 {
status = "okay";
};
/* Expansion GEN1_I2C_*, mini-PCIe I2C, on-board components */
- i2c@0,7000c000 {
+ i2c@7000c000 {
status = "okay";
clock-frequency = <100000>;
};
/* Expansion GEN2_I2C_* */
- i2c@0,7000c400 {
+ i2c@7000c400 {
status = "okay";
clock-frequency = <100000>;
};
/* Expansion CAM_I2C_* */
- i2c@0,7000c500 {
+ i2c@7000c500 {
status = "okay";
clock-frequency = <100000>;
};
/* HDMI DDC */
- hdmi_ddc: i2c@0,7000c700 {
+ hdmi_ddc: i2c@7000c700 {
status = "okay";
clock-frequency = <100000>;
};
/* Expansion PWR_I2C_*, on-board components */
- i2c@0,7000d000 {
+ i2c@7000d000 {
status = "okay";
clock-frequency = <400000>;
};
/* Expansion TS_SPI_* */
- spi@0,7000d400 {
+ spi@7000d400 {
status = "okay";
};
/* Internal SPI */
- spi@0,7000da00 {
+ spi@7000da00 {
status = "okay";
spi-max-frequency = <25000000>;
spi-flash@0 {
};
};
- pmc@0,7000e400 {
+ pmc@7000e400 {
nvidia,invert-interrupt;
nvidia,suspend-mode = <1>;
nvidia,cpu-pwr-good-time = <500>;
};
/* Serial ATA */
- sata@0,70020000 {
+ sata@70020000 {
status = "okay";
- phys = <&{/padctl@0,7009f000/pads/sata/lanes/sata-0}>;
+ phys = <&{/padctl@7009f000/pads/sata/lanes/sata-0}>;
phy-names = "sata-0";
hvdd-supply = <&vdd_3v3_lp0>;
target-12v-supply = <&vdd_12v0_sata>;
};
- hda@0,70030000 {
+ hda@70030000 {
status = "okay";
};
- usb@0,70090000 {
- phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-0}>, /* Micro A/B */
- <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* Mini PCIe */
- <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* USB3 */
- <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>; /* USB3 */
+ usb@70090000 {
+ phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>, /* Micro A/B */
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>, /* Mini PCIe */
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>, /* USB3 */
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>; /* USB3 */
phy-names = "usb2-0", "usb2-1", "usb2-2", "usb3-0";
avddio-pex-supply = <&vdd_1v05_run>;
status = "okay";
};
- padctl@0,7009f000 {
+ padctl@7009f000 {
status = "okay";
pads {
};
/* SD card */
- sdhci@0,700b0400 {
+ sdhci@700b0400 {
status = "okay";
cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
};
/* eMMC */
- sdhci@0,700b0600 {
+ sdhci@700b0600 {
status = "okay";
bus-width = <8>;
non-removable;
};
/* CPU DFLL clock */
- clock@0,70110000 {
+ clock@70110000 {
status = "okay";
vdd-cpu-supply = <&vdd_cpu>;
nvidia,i2c-fs-rate = <400000>;
};
- ahub@0,70300000 {
- i2s@0,70301100 {
+ ahub@70300000 {
+ i2s@70301100 {
status = "okay";
};
};
/* mini-PCIe USB */
- usb@0,7d004000 {
+ usb@7d004000 {
status = "okay";
};
- usb-phy@0,7d004000 {
+ usb-phy@7d004000 {
status = "okay";
};
/* USB A connector */
- usb@0,7d008000 {
+ usb@7d008000 {
status = "okay";
};
- usb-phy@0,7d008000 {
+ usb-phy@7d008000 {
status = "okay";
vbus-supply = <&vdd_usb3_vbus>;
};
thermal-zones {
cpu {
trips {
- trip@0 {
+ trip {
temperature = <101000>;
hysteresis = <0>;
type = "critical";
mem {
trips {
- trip@0 {
+ trip {
temperature = <101000>;
hysteresis = <0>;
type = "critical";
gpu {
trips {
- trip@0 {
+ trip {
temperature = <101000>;
hysteresis = <0>;
type = "critical";
/ {
- clock@0,60006000 {
+ clock@60006000 {
emc-timings-1 {
nvidia,ram-code = <1>;
};
};
- emc@0,7001b000 {
+ emc@7001b000 {
emc-timings-1 {
nvidia,ram-code = <1>;
};
};
- memory-controller@0,70019000 {
+ memory-controller@70019000 {
emc-timings-1 {
nvidia,ram-code = <1>;
ddc-i2c-bus = <&dpaux>;
};
- sdhci@0,700b0400 { /* SD Card on this bus */
+ sdhci@700b0400 { /* SD Card on this bus */
wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
};
nvidia,model = "GoogleNyanBig";
};
- pinmux@0,70000868 {
+ pinmux@70000868 {
pinctrl-names = "default";
pinctrl-0 = <&pinmux_default>;
/ {
- clock@0,60006000 {
+ clock@60006000 {
emc-timings-1 {
nvidia,ram-code = <1>;
};
};
- emc@0,7001b000 {
+ emc@7001b000 {
emc-timings-1 {
nvidia,ram-code = <1>;
};
};
- memory-controller@0,70019000 {
+ memory-controller@70019000 {
emc-timings-1 {
nvidia,ram-code = <1>;
nvidia,model = "GoogleNyanBlaze";
};
- pinmux@0,70000868 {
+ pinmux@70000868 {
pinctrl-names = "default";
pinctrl-0 = <&pinmux_default>;
/ {
aliases {
- rtc0 = "/i2c@0,7000d000/pmic@40";
- rtc1 = "/rtc@0,7000e000";
+ rtc0 = "/i2c@7000d000/pmic@40";
+ rtc1 = "/rtc@7000e000";
serial0 = &uarta;
};
reg = <0x0 0x80000000 0x0 0x80000000>;
};
- host1x@0,50000000 {
- hdmi@0,54280000 {
+ host1x@50000000 {
+ hdmi@54280000 {
status = "okay";
vdd-supply = <&vdd_3v3_hdmi>;
<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
};
- sor@0,54540000 {
+ sor@54540000 {
status = "okay";
nvidia,dpaux = <&dpaux>;
nvidia,panel = <&panel>;
};
- dpaux@0,545c0000 {
+ dpaux@545c0000 {
vdd-supply = <&vdd_3v3_panel>;
status = "okay";
};
};
- serial@0,70006000 {
+ serial@70006000 {
/* Debug connector on the bottom of the board near SD card. */
status = "okay";
};
- pwm@0,7000a000 {
+ pwm@7000a000 {
status = "okay";
};
- i2c@0,7000c000 {
+ i2c@7000c000 {
status = "okay";
clock-frequency = <100000>;
};
};
- i2c@0,7000c400 {
+ i2c@7000c400 {
status = "okay";
clock-frequency = <100000>;
};
};
- i2c@0,7000c500 {
+ i2c@7000c500 {
status = "okay";
clock-frequency = <400000>;
};
};
- hdmi_ddc: i2c@0,7000c700 {
+ hdmi_ddc: i2c@7000c700 {
status = "okay";
clock-frequency = <100000>;
};
- i2c@0,7000d000 {
+ i2c@7000d000 {
status = "okay";
clock-frequency = <400000>;
};
};
- spi@0,7000d400 {
+ spi@7000d400 {
status = "okay";
cros_ec: cros-ec@0 {
};
};
- spi@0,7000da00 {
+ spi@7000da00 {
status = "okay";
spi-max-frequency = <25000000>;
};
};
- pmc@0,7000e400 {
+ pmc@7000e400 {
nvidia,invert-interrupt;
nvidia,suspend-mode = <0>;
nvidia,cpu-pwr-good-time = <500>;
nvidia,sys-clock-req-active-high;
};
- hda@0,70030000 {
+ hda@70030000 {
status = "okay";
};
- usb@0,70090000 {
- phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-0}>, /* 1st USB A */
- <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* Internal USB */
- <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* 2nd USB A */
- <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>, /* 1st USB A */
- <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-1}>; /* 2nd USB A */
+ usb@70090000 {
+ phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>, /* 1st USB A */
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>, /* Internal USB */
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>, /* 2nd USB A */
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, /* 1st USB A */
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>; /* 2nd USB A */
phy-names = "usb2-0", "usb2-1", "usb2-2", "usb3-0", "usb3-1";
avddio-pex-supply = <&vdd_1v05_run>;
status = "okay";
};
- padctl@0,7009f000 {
+ padctl@7009f000 {
status = "okay";
pads {
reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
};
- sdhci@0,700b0000 { /* WiFi/BT on this bus */
+ sdhci@700b0000 { /* WiFi/BT on this bus */
status = "okay";
bus-width = <4>;
no-1-8-v;
keep-power-in-suspend;
};
- sdhci@0,700b0400 { /* SD Card on this bus */
+ sdhci@700b0400 { /* SD Card on this bus */
status = "okay";
cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
vqmmc-supply = <&vddio_sdmmc3>;
};
- sdhci@0,700b0600 { /* eMMC on this bus */
+ sdhci@700b0600 { /* eMMC on this bus */
status = "okay";
bus-width = <8>;
no-1-8-v;
};
/* CPU DFLL clock */
- clock@0,70110000 {
+ clock@70110000 {
status = "disabled";
vdd-cpu-supply = <&vdd_cpu>;
nvidia,i2c-fs-rate = <400000>;
};
- ahub@0,70300000 {
- i2s@0,70301100 {
+ ahub@70300000 {
+ i2s@70301100 {
status = "okay";
};
};
compatible = "nvidia,venice2", "nvidia,tegra124";
aliases {
- rtc0 = "/i2c@0,7000d000/pmic@40";
- rtc1 = "/rtc@0,7000e000";
+ rtc0 = "/i2c@7000d000/pmic@40";
+ rtc1 = "/rtc@7000e000";
serial0 = &uarta;
};
reg = <0x0 0x80000000 0x0 0x80000000>;
};
- host1x@0,50000000 {
- hdmi@0,54280000 {
+ host1x@50000000 {
+ hdmi@54280000 {
status = "okay";
vdd-supply = <&vdd_3v3_hdmi>;
<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
};
- sor@0,54540000 {
+ sor@54540000 {
status = "okay";
nvidia,dpaux = <&dpaux>;
nvidia,panel = <&panel>;
};
- dpaux@0,545c0000 {
+ dpaux@545c0000 {
vdd-supply = <&vdd_3v3_panel>;
status = "okay";
};
vdd-supply = <&vdd_gpu>;
};
- pinmux: pinmux@0,70000868 {
+ pinmux: pinmux@70000868 {
pinctrl-names = "boot";
pinctrl-0 = <&pinmux_boot>;
};
};
- serial@0,70006000 {
+ serial@70006000 {
status = "okay";
};
- pwm@0,7000a000 {
+ pwm@7000a000 {
status = "okay";
};
- i2c@0,7000c000 {
+ i2c@7000c000 {
status = "okay";
clock-frequency = <100000>;
};
};
- i2c@0,7000c400 {
+ i2c@7000c400 {
status = "okay";
clock-frequency = <100000>;
};
};
- i2c@0,7000c500 {
+ i2c@7000c500 {
status = "okay";
clock-frequency = <100000>;
};
- hdmi_ddc: i2c@0,7000c700 {
+ hdmi_ddc: i2c@7000c700 {
status = "okay";
clock-frequency = <100000>;
};
- i2c@0,7000d000 {
+ i2c@7000d000 {
status = "okay";
clock-frequency = <400000>;
};
};
- spi@0,7000d400 {
+ spi@7000d400 {
status = "okay";
cros_ec: cros-ec@0 {
};
};
- spi@0,7000da00 {
+ spi@7000da00 {
status = "okay";
spi-max-frequency = <25000000>;
spi-flash@0 {
};
};
- pmc@0,7000e400 {
+ pmc@7000e400 {
nvidia,invert-interrupt;
nvidia,suspend-mode = <1>;
nvidia,cpu-pwr-good-time = <500>;
nvidia,sys-clock-req-active-high;
};
- hda@0,70030000 {
+ hda@70030000 {
status = "okay";
};
- usb@0,70090000 {
- phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-0}>, /* 1st USB A */
- <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* Internal USB */
- <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* 2nd USB A */
- <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>, /* 1st USB A */
- <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-1}>; /* 2nd USB A */
+ usb@70090000 {
+ phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>, /* 1st USB A */
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>, /* Internal USB */
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>, /* 2nd USB A */
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, /* 1st USB A */
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>; /* 2nd USB A */
phy-names = "usb2-0", "usb2-1", "usb2-2", "usb3-0", "usb3-1";
avddio-pex-supply = <&vdd_1v05_run>;
status = "okay";
};
- padctl@0,7009f000 {
+ padctl@7009f000 {
pads {
usb2 {
status = "okay";
};
};
- sdhci@0,700b0400 {
+ sdhci@700b0400 {
cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
vqmmc-supply = <&vddio_sdmmc3>;
};
- sdhci@0,700b0600 {
+ sdhci@700b0600 {
status = "okay";
bus-width = <8>;
non-removable;
};
- ahub@0,70300000 {
- i2s@0,70301100 {
+ ahub@70300000 {
+ i2s@70301100 {
status = "okay";
};
};
- usb@0,7d000000 {
+ usb@7d000000 {
status = "okay";
};
- usb-phy@0,7d000000 {
+ usb-phy@7d000000 {
status = "okay";
vbus-supply = <&vdd_usb1_vbus>;
};
- usb@0,7d004000 {
+ usb@7d004000 {
status = "okay";
};
- usb-phy@0,7d004000 {
+ usb-phy@7d004000 {
status = "okay";
vbus-supply = <&vdd_run_cam>;
};
- usb@0,7d008000 {
+ usb@7d008000 {
status = "okay";
};
- usb-phy@0,7d008000 {
+ usb-phy@7d008000 {
status = "okay";
vbus-supply = <&vdd_usb3_vbus>;
};
#address-cells = <2>;
#size-cells = <2>;
- pcie-controller@0,01003000 {
+ pcie-controller@01003000 {
compatible = "nvidia,tegra124-pcie";
device_type = "pci";
reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */
};
};
- host1x@0,50000000 {
+ host1x@50000000 {
compatible = "nvidia,tegra124-host1x", "simple-bus";
reg = <0x0 0x50000000 0x0 0x00034000>;
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */
ranges = <0 0x54000000 0 0x54000000 0 0x01000000>;
- dc@0,54200000 {
+ dc@54200000 {
compatible = "nvidia,tegra124-dc";
reg = <0x0 0x54200000 0x0 0x00040000>;
interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
nvidia,head = <0>;
};
- dc@0,54240000 {
+ dc@54240000 {
compatible = "nvidia,tegra124-dc";
reg = <0x0 0x54240000 0x0 0x00040000>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
nvidia,head = <1>;
};
- hdmi@0,54280000 {
+ hdmi@54280000 {
compatible = "nvidia,tegra124-hdmi";
reg = <0x0 0x54280000 0x0 0x00040000>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- sor@0,54540000 {
+ sor@54540000 {
compatible = "nvidia,tegra124-sor";
reg = <0x0 0x54540000 0x0 0x00040000>;
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- dpaux: dpaux@0,545c0000 {
+ dpaux: dpaux@545c0000 {
compatible = "nvidia,tegra124-dpaux";
reg = <0x0 0x545c0000 0x0 0x00040000>;
interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
};
};
- gic: interrupt-controller@0,50041000 {
+ gic: interrupt-controller@50041000 {
compatible = "arm,cortex-a15-gic";
#interrupt-cells = <3>;
interrupt-controller;
interrupt-parent = <&gic>;
};
+ /*
+ * Please keep the following 0, notation in place as a former mainline
+ * U-Boot version was looking for that particular notation in order to
+ * perform required fix-ups on that GPU node.
+ */
gpu@0,57000000 {
compatible = "nvidia,gk20a";
reg = <0x0 0x57000000 0x0 0x01000000>,
interrupt-parent = <&gic>;
};
- timer@0,60005000 {
+ timer@60005000 {
compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer", "nvidia,tegra20-timer";
reg = <0x0 0x60005000 0x0 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
clocks = <&tegra_car TEGRA124_CLK_TIMER>;
};
- tegra_car: clock@0,60006000 {
+ tegra_car: clock@60006000 {
compatible = "nvidia,tegra124-car";
reg = <0x0 0x60006000 0x0 0x1000>;
#clock-cells = <1>;
nvidia,external-memory-controller = <&emc>;
};
- flow-controller@0,60007000 {
+ flow-controller@60007000 {
compatible = "nvidia,tegra124-flowctrl";
reg = <0x0 0x60007000 0x0 0x1000>;
};
- actmon@0,6000c800 {
+ actmon@6000c800 {
compatible = "nvidia,tegra124-actmon";
reg = <0x0 0x6000c800 0x0 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
reset-names = "actmon";
};
- gpio: gpio@0,6000d000 {
+ gpio: gpio@6000d000 {
compatible = "nvidia,tegra124-gpio", "nvidia,tegra30-gpio";
reg = <0x0 0x6000d000 0x0 0x1000>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
*/
};
- apbdma: dma@0,60020000 {
+ apbdma: dma@60020000 {
compatible = "nvidia,tegra124-apbdma", "nvidia,tegra148-apbdma";
reg = <0x0 0x60020000 0x0 0x1400>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
#dma-cells = <1>;
};
- apbmisc@0,70000800 {
+ apbmisc@70000800 {
compatible = "nvidia,tegra124-apbmisc", "nvidia,tegra20-apbmisc";
reg = <0x0 0x70000800 0x0 0x64>, /* Chip revision */
<0x0 0x7000e864 0x0 0x04>; /* Strapping options */
};
- pinmux: pinmux@0,70000868 {
+ pinmux: pinmux@70000868 {
compatible = "nvidia,tegra124-pinmux";
reg = <0x0 0x70000868 0x0 0x164>, /* Pad control registers */
<0x0 0x70003000 0x0 0x434>, /* Mux registers */
* the APB DMA based serial driver, the compatible is
* "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart".
*/
- uarta: serial@0,70006000 {
+ uarta: serial@70006000 {
compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
reg = <0x0 0x70006000 0x0 0x40>;
reg-shift = <2>;
status = "disabled";
};
- uartb: serial@0,70006040 {
+ uartb: serial@70006040 {
compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
reg = <0x0 0x70006040 0x0 0x40>;
reg-shift = <2>;
status = "disabled";
};
- uartc: serial@0,70006200 {
+ uartc: serial@70006200 {
compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
reg = <0x0 0x70006200 0x0 0x40>;
reg-shift = <2>;
status = "disabled";
};
- uartd: serial@0,70006300 {
+ uartd: serial@70006300 {
compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
reg = <0x0 0x70006300 0x0 0x40>;
reg-shift = <2>;
status = "disabled";
};
- pwm: pwm@0,7000a000 {
+ pwm: pwm@7000a000 {
compatible = "nvidia,tegra124-pwm", "nvidia,tegra20-pwm";
reg = <0x0 0x7000a000 0x0 0x100>;
#pwm-cells = <2>;
status = "disabled";
};
- i2c@0,7000c000 {
+ i2c@7000c000 {
compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
reg = <0x0 0x7000c000 0x0 0x100>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- i2c@0,7000c400 {
+ i2c@7000c400 {
compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
reg = <0x0 0x7000c400 0x0 0x100>;
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- i2c@0,7000c500 {
+ i2c@7000c500 {
compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
reg = <0x0 0x7000c500 0x0 0x100>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- i2c@0,7000c700 {
+ i2c@7000c700 {
compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
reg = <0x0 0x7000c700 0x0 0x100>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- i2c@0,7000d000 {
+ i2c@7000d000 {
compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
reg = <0x0 0x7000d000 0x0 0x100>;
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- i2c@0,7000d100 {
+ i2c@7000d100 {
compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
reg = <0x0 0x7000d100 0x0 0x100>;
interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- spi@0,7000d400 {
+ spi@7000d400 {
compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi";
reg = <0x0 0x7000d400 0x0 0x200>;
interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- spi@0,7000d600 {
+ spi@7000d600 {
compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi";
reg = <0x0 0x7000d600 0x0 0x200>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- spi@0,7000d800 {
+ spi@7000d800 {
compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi";
reg = <0x0 0x7000d800 0x0 0x200>;
interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- spi@0,7000da00 {
+ spi@7000da00 {
compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi";
reg = <0x0 0x7000da00 0x0 0x200>;
interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- spi@0,7000dc00 {
+ spi@7000dc00 {
compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi";
reg = <0x0 0x7000dc00 0x0 0x200>;
interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- spi@0,7000de00 {
+ spi@7000de00 {
compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi";
reg = <0x0 0x7000de00 0x0 0x200>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- rtc@0,7000e000 {
+ rtc@7000e000 {
compatible = "nvidia,tegra124-rtc", "nvidia,tegra20-rtc";
reg = <0x0 0x7000e000 0x0 0x100>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA124_CLK_RTC>;
};
- pmc@0,7000e400 {
+ pmc@7000e400 {
compatible = "nvidia,tegra124-pmc";
reg = <0x0 0x7000e400 0x0 0x400>;
clocks = <&tegra_car TEGRA124_CLK_PCLK>, <&clk32k_in>;
clock-names = "pclk", "clk32k_in";
};
- fuse@0,7000f800 {
+ fuse@7000f800 {
compatible = "nvidia,tegra124-efuse";
reg = <0x0 0x7000f800 0x0 0x400>;
clocks = <&tegra_car TEGRA124_CLK_FUSE>;
reset-names = "fuse";
};
- mc: memory-controller@0,70019000 {
+ mc: memory-controller@70019000 {
compatible = "nvidia,tegra124-mc";
reg = <0x0 0x70019000 0x0 0x1000>;
clocks = <&tegra_car TEGRA124_CLK_MC>;
#iommu-cells = <1>;
};
- emc: emc@0,7001b000 {
+ emc: emc@7001b000 {
compatible = "nvidia,tegra124-emc";
reg = <0x0 0x7001b000 0x0 0x1000>;
nvidia,memory-controller = <&mc>;
};
- sata@0,70020000 {
+ sata@70020000 {
compatible = "nvidia,tegra124-ahci";
reg = <0x0 0x70027000 0x0 0x2000>, /* AHCI */
<0x0 0x70020000 0x0 0x7000>; /* SATA */
status = "disabled";
};
- hda@0,70030000 {
+ hda@70030000 {
compatible = "nvidia,tegra124-hda", "nvidia,tegra30-hda";
reg = <0x0 0x70030000 0x0 0x10000>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- usb@0,70090000 {
+ usb@70090000 {
compatible = "nvidia,tegra124-xusb";
reg = <0x0 0x70090000 0x0 0x8000>,
<0x0 0x70098000 0x0 0x1000>,
status = "disabled";
};
- padctl: padctl@0,7009f000 {
+ padctl: padctl@7009f000 {
compatible = "nvidia,tegra124-xusb-padctl";
reg = <0x0 0x7009f000 0x0 0x1000>;
resets = <&tegra_car 142>;
};
};
- sdhci@0,700b0000 {
+ sdhci@700b0000 {
compatible = "nvidia,tegra124-sdhci";
reg = <0x0 0x700b0000 0x0 0x200>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- sdhci@0,700b0200 {
+ sdhci@700b0200 {
compatible = "nvidia,tegra124-sdhci";
reg = <0x0 0x700b0200 0x0 0x200>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- sdhci@0,700b0400 {
+ sdhci@700b0400 {
compatible = "nvidia,tegra124-sdhci";
reg = <0x0 0x700b0400 0x0 0x200>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- sdhci@0,700b0600 {
+ sdhci@700b0600 {
compatible = "nvidia,tegra124-sdhci";
reg = <0x0 0x700b0600 0x0 0x200>;
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- soctherm: thermal-sensor@0,700e2000 {
+ soctherm: thermal-sensor@700e2000 {
compatible = "nvidia,tegra124-soctherm";
reg = <0x0 0x700e2000 0x0 0x1000>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
#thermal-sensor-cells = <1>;
};
- dfll: clock@0,70110000 {
+ dfll: clock@70110000 {
compatible = "nvidia,tegra124-dfll";
reg = <0 0x70110000 0 0x100>, /* DFLL control */
<0 0x70110000 0 0x100>, /* I2C output control */
status = "disabled";
};
- ahub@0,70300000 {
+ ahub@70300000 {
compatible = "nvidia,tegra124-ahub";
reg = <0x0 0x70300000 0x0 0x200>,
<0x0 0x70300800 0x0 0x800>,
#address-cells = <2>;
#size-cells = <2>;
- tegra_i2s0: i2s@0,70301000 {
+ tegra_i2s0: i2s@70301000 {
compatible = "nvidia,tegra124-i2s";
reg = <0x0 0x70301000 0x0 0x100>;
nvidia,ahub-cif-ids = <4 4>;
status = "disabled";
};
- tegra_i2s1: i2s@0,70301100 {
+ tegra_i2s1: i2s@70301100 {
compatible = "nvidia,tegra124-i2s";
reg = <0x0 0x70301100 0x0 0x100>;
nvidia,ahub-cif-ids = <5 5>;
status = "disabled";
};
- tegra_i2s2: i2s@0,70301200 {
+ tegra_i2s2: i2s@70301200 {
compatible = "nvidia,tegra124-i2s";
reg = <0x0 0x70301200 0x0 0x100>;
nvidia,ahub-cif-ids = <6 6>;
status = "disabled";
};
- tegra_i2s3: i2s@0,70301300 {
+ tegra_i2s3: i2s@70301300 {
compatible = "nvidia,tegra124-i2s";
reg = <0x0 0x70301300 0x0 0x100>;
nvidia,ahub-cif-ids = <7 7>;
status = "disabled";
};
- tegra_i2s4: i2s@0,70301400 {
+ tegra_i2s4: i2s@70301400 {
compatible = "nvidia,tegra124-i2s";
reg = <0x0 0x70301400 0x0 0x100>;
nvidia,ahub-cif-ids = <8 8>;
};
};
- usb@0,7d000000 {
+ usb@7d000000 {
compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
reg = <0x0 0x7d000000 0x0 0x4000>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- phy1: usb-phy@0,7d000000 {
+ phy1: usb-phy@7d000000 {
compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
reg = <0x0 0x7d000000 0x0 0x4000>,
<0x0 0x7d000000 0x0 0x4000>;
status = "disabled";
};
- usb@0,7d004000 {
+ usb@7d004000 {
compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
reg = <0x0 0x7d004000 0x0 0x4000>;
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- phy2: usb-phy@0,7d004000 {
+ phy2: usb-phy@7d004000 {
compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
reg = <0x0 0x7d004000 0x0 0x4000>,
<0x0 0x7d000000 0x0 0x4000>;
status = "disabled";
};
- usb@0,7d008000 {
+ usb@7d008000 {
compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
reg = <0x0 0x7d008000 0x0 0x4000>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- phy3: usb-phy@0,7d008000 {
+ phy3: usb-phy@7d008000 {
compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
reg = <0x0 0x7d008000 0x0 0x4000>,
<0x0 0x7d000000 0x0 0x4000>;
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
blocks = <0x5>;
irq-trigger = <0x1>;
- stmpe_touchscreen {
+ stmpe_touchscreen@0 {
compatible = "st,stmpe-ts";
reg = <0>;
/* 3.25 MHz ADC clock speed */
clk32k_in: clk@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
+
clk16m: clk@1 {
compatible = "fixed-clock";
- reg=<1>;
+ reg = <1>;
#clock-cells = <0>;
clock-frequency = <16000000>;
clock-output-names = "clk16m";
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clk32k_in: clock@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
clocks {
clk16m: clk@1 {
compatible = "fixed-clock";
- reg=<1>;
+ reg = <1>;
#clock-cells = <0>;
clock-frequency = <16000000>;
clock-output-names = "clk16m";
clk32k_in: clk@0 {
compatible = "fixed-clock";
- reg=<0>;
+ reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
};
};
reg = <0x58c00000 0x400>;
#address-cells = <2>;
#size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_system_bus>;
};
smpctrl@59800000 {
interrupt-controller;
};
- pinctrl: pinctrl@5f801000 {
- /* specify compatible in each SoC DTSI */
- reg = <0x5f801000 0xe00>;
+ soc-glue@5f800000 {
+ compatible = "simple-mfd", "syscon";
+ reg = <0x5f800000 0x2000>;
+
+ pinctrl: pinctrl {
+ /* specify compatible in each SoC DTSI */
+ };
};
};
};
};
&pinctrl {
- compatible = "socionext,ph1-ld4-pinctrl", "syscon";
+ compatible = "socionext,uniphier-ld4-pinctrl";
};
* which makes the pinctrl driver unshareable.
*/
&pinctrl {
- compatible = "socionext,ph1-ld6b-pinctrl", "syscon";
+ compatible = "socionext,uniphier-ld6b-pinctrl";
};
};
&pinctrl {
- compatible = "socionext,ph1-pro4-pinctrl", "syscon";
+ compatible = "socionext,uniphier-pro4-pinctrl";
};
};
&pinctrl {
- compatible = "socionext,ph1-pro5-pinctrl", "syscon";
+ compatible = "socionext,uniphier-pro5-pinctrl";
};
};
&pinctrl {
- compatible = "socionext,ph1-sld8-pinctrl", "syscon";
+ compatible = "socionext,uniphier-sld8-pinctrl";
};
function = "nand";
};
+ pinctrl_system_bus: system_bus_grp {
+ groups = "system_bus", "system_bus_cs1";
+ function = "system_bus";
+ };
+
pinctrl_uart0: uart0_grp {
groups = "uart0";
function = "uart0";
};
chosen {
- stdout-path = "serial2:115200n8";
+ stdout-path = "serial0:115200n8";
};
aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- serial2 = &serial2;
+ serial0 = &serial2;
+ serial1 = &serial0;
+ serial2 = &serial1;
i2c0 = &i2c0;
i2c2 = &i2c2;
i2c4 = &i2c4;
};
chosen {
- stdout-path = "serial2:115200n8";
+ stdout-path = "serial0:115200n8";
};
aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- serial2 = &serial2;
+ serial0 = &serial2;
+ serial1 = &serial0;
+ serial2 = &serial1;
i2c0 = &i2c0;
i2c4 = &i2c4;
i2c5 = &i2c5;
};
&pinctrl {
- compatible = "socionext,proxstream2-pinctrl", "syscon";
+ compatible = "socionext,uniphier-pxs2-pinctrl";
};
/ {
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
};
- i2c@0 {
+ i2c-gpio-0 {
status = "okay";
};
};
/ {
chosen {
- bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+ bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+ stdout-path = "serial0:115200n8";
};
memory {
reg = <0x20000000 0x4000000>;
};
- i2c@0 {
+ i2c-gpio-0 {
rv3029c2@56 {
compatible = "rv3029c2";
reg = <0x56>;
#define OF_SECONDARY_BOOT "secondary-boot-reg"
#define MPIDR_CPUID_BITMASK 0x3
-/* I/O address of register used to coordinate secondary core startup */
-static u32 secondary_boot_addr;
-
/*
* Enable the Cortex A9 Snoop Control Unit
*
return 0;
}
-static int nsp_write_lut(void)
+static u32 secondary_boot_addr_for(unsigned int cpu)
+{
+ u32 secondary_boot_addr = 0;
+ struct device_node *cpu_node = of_get_cpu_node(cpu, NULL);
+
+ if (!cpu_node) {
+ pr_err("Failed to find device tree node for CPU%u\n", cpu);
+ return 0;
+ }
+
+ if (of_property_read_u32(cpu_node,
+ OF_SECONDARY_BOOT,
+ &secondary_boot_addr))
+ pr_err("required secondary boot register not specified for CPU%u\n",
+ cpu);
+
+ of_node_put(cpu_node);
+
+ return secondary_boot_addr;
+}
+
+static int nsp_write_lut(unsigned int cpu)
{
void __iomem *sku_rom_lut;
phys_addr_t secondary_startup_phy;
+ const u32 secondary_boot_addr = secondary_boot_addr_for(cpu);
- if (!secondary_boot_addr) {
- pr_warn("required secondary boot register not specified\n");
+ if (!secondary_boot_addr)
return -EINVAL;
- }
sku_rom_lut = ioremap_nocache((phys_addr_t)secondary_boot_addr,
- sizeof(secondary_boot_addr));
+ sizeof(phys_addr_t));
if (!sku_rom_lut) {
- pr_warn("unable to ioremap SKU-ROM LUT register\n");
+ pr_warn("unable to ioremap SKU-ROM LUT register for cpu %u\n", cpu);
return -ENOMEM;
}
static void __init bcm_smp_prepare_cpus(unsigned int max_cpus)
{
- static cpumask_t only_cpu_0 = { CPU_BITS_CPU0 };
- struct device_node *cpus_node = NULL;
- struct device_node *cpu_node = NULL;
- int ret;
-
- /*
- * This function is only called via smp_ops->smp_prepare_cpu().
- * That only happens if a "/cpus" device tree node exists
- * and has an "enable-method" property that selects the SMP
- * operations defined herein.
- */
- cpus_node = of_find_node_by_path("/cpus");
- if (!cpus_node)
- return;
-
- for_each_child_of_node(cpus_node, cpu_node) {
- u32 cpuid;
-
- if (of_node_cmp(cpu_node->type, "cpu"))
- continue;
-
- if (of_property_read_u32(cpu_node, "reg", &cpuid)) {
- pr_debug("%s: missing reg property\n",
- cpu_node->full_name);
- ret = -ENOENT;
- goto out;
- }
-
- /*
- * "secondary-boot-reg" property should be defined only
- * for secondary cpu
- */
- if ((cpuid & MPIDR_CPUID_BITMASK) == 1) {
- /*
- * Our secondary enable method requires a
- * "secondary-boot-reg" property to specify a register
- * address used to request the ROM code boot a secondary
- * core. If we have any trouble getting this we fall
- * back to uniprocessor mode.
- */
- if (of_property_read_u32(cpu_node,
- OF_SECONDARY_BOOT,
- &secondary_boot_addr)) {
- pr_warn("%s: no" OF_SECONDARY_BOOT "property\n",
- cpu_node->name);
- ret = -ENOENT;
- goto out;
- }
- }
- }
-
- /*
- * Enable the SCU on Cortex A9 based SoCs. If -ENOENT is
- * returned, the SoC reported a uniprocessor configuration.
- * We bail on any other error.
- */
- ret = scu_a9_enable();
-out:
- of_node_put(cpu_node);
- of_node_put(cpus_node);
+ const cpumask_t only_cpu_0 = { CPU_BITS_CPU0 };
- if (ret) {
+ /* Enable the SCU on Cortex A9 based SoCs */
+ if (scu_a9_enable()) {
/* Update the CPU present map to reflect uniprocessor mode */
- pr_warn("disabling SMP\n");
+ pr_warn("failed to enable A9 SCU - disabling SMP\n");
init_cpu_present(&only_cpu_0);
}
}
u32 cpu_id;
u32 boot_val;
bool timeout = false;
+ const u32 secondary_boot_addr = secondary_boot_addr_for(cpu);
cpu_id = cpu_logical_map(cpu);
if (cpu_id & ~BOOT_ADDR_CPUID_MASK) {
return -EINVAL;
}
- if (!secondary_boot_addr) {
- pr_err("required secondary boot register not specified\n");
+ if (!secondary_boot_addr)
return -EINVAL;
- }
- boot_reg = ioremap_nocache(
- (phys_addr_t)secondary_boot_addr, sizeof(u32));
+ boot_reg = ioremap_nocache((phys_addr_t)secondary_boot_addr,
+ sizeof(phys_addr_t));
if (!boot_reg) {
pr_err("unable to map boot register for cpu %u\n", cpu_id);
return -ENOMEM;
* After wake up, secondary core branches to the startup
* address programmed at SKU ROM LUT location.
*/
- ret = nsp_write_lut();
+ ret = nsp_write_lut(cpu);
if (ret) {
pr_err("unable to write startup addr to SKU ROM LUT\n");
goto out;
return ret;
}
-static const struct smp_operations bcm_smp_ops __initconst = {
+static const struct smp_operations kona_smp_ops __initconst = {
.smp_prepare_cpus = bcm_smp_prepare_cpus,
.smp_boot_secondary = kona_boot_secondary,
};
CPU_METHOD_OF_DECLARE(bcm_smp_bcm281xx, "brcm,bcm11351-cpu-method",
- &bcm_smp_ops);
+ &kona_smp_ops);
static const struct smp_operations bcm23550_smp_ops __initconst = {
.smp_boot_secondary = bcm23550_boot_secondary,
DT_CLK(NULL, "smartreflex1_fck", "smartreflex1_fck"),
DT_CLK(NULL, "sha0_fck", "sha0_fck"),
DT_CLK(NULL, "aes0_fck", "aes0_fck"),
+ DT_CLK(NULL, "rng_fck", "rng_fck"),
DT_CLK(NULL, "timer1_fck", "timer1_fck"),
DT_CLK(NULL, "timer2_fck", "timer2_fck"),
DT_CLK(NULL, "timer3_fck", "timer3_fck"),
struct completion done;
};
-static int spi_st_clk_enable(struct spi_st *spi_st)
-{
- /*
- * Current platforms use one of the core clocks for SPI and I2C.
- * If we attempt to disable the clock, the system will hang.
- *
- * TODO: Remove this when platform supports power domains.
- */
- return 0;
-
- return clk_prepare_enable(spi_st->clk);
-}
-
-static void spi_st_clk_disable(struct spi_st *spi_st)
-{
- /*
- * Current platforms use one of the core clocks for SPI and I2C.
- * If we attempt to disable the clock, the system will hang.
- *
- * TODO: Remove this when platform supports power domains.
- */
- return;
-
- clk_disable_unprepare(spi_st->clk);
-}
-
/* Load the TX FIFO */
static void ssc_write_tx_fifo(struct spi_st *spi_st)
{
goto put_master;
}
- ret = spi_st_clk_enable(spi_st);
+ ret = clk_prepare_enable(spi_st->clk);
if (ret)
goto put_master;
return 0;
clk_disable:
- spi_st_clk_disable(spi_st);
+ clk_disable_unprepare(spi_st->clk);
put_master:
spi_master_put(master);
return ret;
struct spi_master *master = platform_get_drvdata(pdev);
struct spi_st *spi_st = spi_master_get_devdata(master);
- spi_st_clk_disable(spi_st);
+ clk_disable_unprepare(spi_st->clk);
pinctrl_pm_select_sleep_state(&pdev->dev);
writel_relaxed(0, spi_st->base + SSC_IEN);
pinctrl_pm_select_sleep_state(dev);
- spi_st_clk_disable(spi_st);
+ clk_disable_unprepare(spi_st->clk);
return 0;
}
struct spi_st *spi_st = spi_master_get_devdata(master);
int ret;
- ret = spi_st_clk_enable(spi_st);
+ ret = clk_prepare_enable(spi_st->clk);
pinctrl_pm_select_default_state(dev);
return ret;
--- /dev/null
+/*
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_R8A7792_H__
+#define __DT_BINDINGS_CLOCK_R8A7792_H__
+
+/* CPG */
+#define R8A7792_CLK_MAIN 0
+#define R8A7792_CLK_PLL0 1
+#define R8A7792_CLK_PLL1 2
+#define R8A7792_CLK_PLL3 3
+#define R8A7792_CLK_LB 4
+#define R8A7792_CLK_QSPI 5
+#define R8A7792_CLK_Z 6
+
+/* MSTP0 */
+#define R8A7792_CLK_MSIOF0 0
+
+/* MSTP1 */
+#define R8A7792_CLK_JPU 6
+#define R8A7792_CLK_TMU1 11
+#define R8A7792_CLK_TMU3 21
+#define R8A7792_CLK_TMU2 22
+#define R8A7792_CLK_CMT0 24
+#define R8A7792_CLK_TMU0 25
+#define R8A7792_CLK_VSP1DU1 27
+#define R8A7792_CLK_VSP1DU0 28
+#define R8A7792_CLK_VSP1_SY 31
+
+/* MSTP2 */
+#define R8A7792_CLK_MSIOF1 8
+#define R8A7792_CLK_SYS_DMAC1 18
+#define R8A7792_CLK_SYS_DMAC0 19
+
+/* MSTP3 */
+#define R8A7792_CLK_TPU0 4
+#define R8A7792_CLK_SDHI0 14
+#define R8A7792_CLK_CMT1 29
+
+/* MSTP4 */
+#define R8A7792_CLK_IRQC 7
+
+/* MSTP5 */
+#define R8A7792_CLK_AUDIO_DMAC0 2
+#define R8A7792_CLK_THERMAL 22
+#define R8A7792_CLK_PWM 23
+
+/* MSTP7 */
+#define R8A7792_CLK_HSCIF1 16
+#define R8A7792_CLK_HSCIF0 17
+#define R8A7792_CLK_SCIF3 18
+#define R8A7792_CLK_SCIF2 19
+#define R8A7792_CLK_SCIF1 20
+#define R8A7792_CLK_SCIF0 21
+#define R8A7792_CLK_DU1 23
+#define R8A7792_CLK_DU0 24
+
+/* MSTP8 */
+#define R8A7792_CLK_VIN5 4
+#define R8A7792_CLK_VIN4 5
+#define R8A7792_CLK_VIN3 8
+#define R8A7792_CLK_VIN2 9
+#define R8A7792_CLK_VIN1 10
+#define R8A7792_CLK_VIN0 11
+#define R8A7792_CLK_ETHERAVB 12
+
+/* MSTP9 */
+#define R8A7792_CLK_GPIO7 4
+#define R8A7792_CLK_GPIO6 5
+#define R8A7792_CLK_GPIO5 7
+#define R8A7792_CLK_GPIO4 8
+#define R8A7792_CLK_GPIO3 9
+#define R8A7792_CLK_GPIO2 10
+#define R8A7792_CLK_GPIO1 11
+#define R8A7792_CLK_GPIO0 12
+#define R8A7792_CLK_GPIO11 13
+#define R8A7792_CLK_GPIO10 14
+#define R8A7792_CLK_CAN1 15
+#define R8A7792_CLK_CAN0 16
+#define R8A7792_CLK_QSPI_MOD 17
+#define R8A7792_CLK_GPIO9 19
+#define R8A7792_CLK_GPIO8 21
+#define R8A7792_CLK_I2C5 25
+#define R8A7792_CLK_IICDVFS 26
+#define R8A7792_CLK_I2C4 27
+#define R8A7792_CLK_I2C3 28
+#define R8A7792_CLK_I2C2 29
+#define R8A7792_CLK_I2C1 30
+#define R8A7792_CLK_I2C0 31
+
+/* MSTP10 */
+#define R8A7792_CLK_SSI_ALL 5
+#define R8A7792_CLK_SSI4 11
+#define R8A7792_CLK_SSI3 12
+
+#endif /* __DT_BINDINGS_CLOCK_R8A7792_H__ */
#define R8A7794_CLK_IRQC 7
/* MSTP5 */
-#define R8A7794_CLK_THERMAL 22
#define R8A7794_CLK_PWM 23
/* MSTP7 */
#ifndef _DT_BINDINGS_CLK_STIH407
#define _DT_BINDINGS_CLK_STIH407
+/* CLOCKGEN A0 */
+#define CLK_IC_LMI0 0
+#define CLK_IC_LMI1 1
+
/* CLOCKGEN C0 */
#define CLK_ICN_GPU 0
#define CLK_FDMA 1
--- /dev/null
+/*
+ * This header provides constants for Keystone pinctrl bindings.
+ *
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_KEYSTONE_H
+#define _DT_BINDINGS_PINCTRL_KEYSTONE_H
+
+#define MUX_MODE0 0
+#define MUX_MODE1 1
+#define MUX_MODE2 2
+#define MUX_MODE3 3
+#define MUX_MODE4 4
+#define MUX_MODE5 5
+
+#define BUFFER_CLASS_B (0 << 19)
+#define BUFFER_CLASS_C (1 << 19)
+#define BUFFER_CLASS_D (2 << 19)
+#define BUFFER_CLASS_E (3 << 19)
+
+#define PULL_DISABLE (1 << 16)
+#define PIN_PULLUP (1 << 17)
+#define PIN_PULLDOWN (0 << 17)
+
+#define KEYSTONE_IOPAD_OFFSET(pa, offset) (((pa) & 0xffff) - (offset))
+
+#define K2G_CORE_IOPAD(pa) KEYSTONE_IOPAD_OFFSET((pa), 0x1000)
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+#ifndef __DT_BINDINGS_POWER_R8A7792_SYSC_H__
+#define __DT_BINDINGS_POWER_R8A7792_SYSC_H__
+
+/*
+ * These power domain indices match the numbers of the interrupt bits
+ * representing the power areas in the various Interrupt Registers
+ * (e.g. SYSCISR, Interrupt Status Register)
+ */
+
+#define R8A7792_PD_CA15_CPU0 0
+#define R8A7792_PD_CA15_CPU1 1
+#define R8A7792_PD_CA15_SCU 12
+#define R8A7792_PD_SGX 20
+#define R8A7792_PD_IMP 24
+
+/* Always-on power area */
+#define R8A7792_PD_ALWAYS_ON 32
+
+#endif /* __DT_BINDINGS_POWER_R8A7792_SYSC_H__ */
projects / cascardo / linux.git / commitdiff